10-Bit, Integrated, Multiformat SDTV Video Decoder and RGB Graphics Digitizer ADV7181C FEATURES GENERAL DESCRIPTION Four 10-bit ADCs sampling up to 110 MHz 6 analog input channels SCART fast blank support Internal antialias filters NTSC, PAL, SECAM color standards support 525p/625p component progressive scan support 720p/1080i component HDTV support Digitizes RGB graphics up to 1280 × 1024 at 60 Hz (SXGA) 3 × 3 color space conversion matrix Industrial temperature range: −40°C to +85°C 12-bit 4:4:4 DDR, 8-/10-/16-/20-bit SDR pixel output interface Programmable interrupt request output pin Small package Low pin count Single front end for video and graphics The ADV7181C is a high quality, single-chip, multiformat video decoder and graphics digitizer. This multiformat decoder supports the conversion of PAL, NTSC, and SECAM standards in the form of composite or S-Video into a digital ITU-R BT.656 format. The ADV7181C also supports the decoding of a component RGB/YPrPb video signal into a digital YCrCb or RGB DDR pixel output stream. The support for component video includes standards such as 525i, 625i, 525p, 625p, 720p, 1080i, and many other HD and SMPTE standards. Graphics digitization is also supported by the ADV7181C; it is capable of digitizing RGB graphics signals from VGA to SXGA rates and converting them into a digital DDR RGB or YCrCb pixel output stream. SCART and overlay functionality are enabled by the ability of the ADV7181C to process simultaneously CVBS and standard definition RGB signals. The mixing of these signals is controlled by the fast blank pin. APPLICATIONS Automotive entertainment HDTVs LCD/DLP projectors HDTV STBs with PVR DVD recorders with progressive scan input support AVR receivers The ADV7181C contains two main processing sections. The first section is the standard definition processor (SDP), which processes all PAL, NTSC, and SECAM signal types. The second section is the component processor (CP), which processes YPrPb and RGB component formats, including RGB graphics. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2008 Analog Devices, Inc. All rights reserved. ADV7181C TABLE OF CONTENTS Features .............................................................................................. 1 SDP Pixel Data Output Modes ................................................. 11 Applications ....................................................................................... 1 CP Pixel Data Output Modes ................................................... 11 General Description ......................................................................... 1 Composite and S-Video Processing ......................................... 11 Revision History ............................................................................... 2 Component Video Processing .................................................. 12 Functional Block Diagram .............................................................. 3 RGB Graphics Processing ......................................................... 12 Specifications..................................................................................... 4 General Features ......................................................................... 12 Electrical Characteristics ............................................................. 4 Detailed Description ...................................................................... 13 Video Specifications ..................................................................... 5 Analog Front End ....................................................................... 13 Timing Characteristics ................................................................ 6 Standard Definition Processor (SDP)...................................... 13 Analog Specifications ................................................................... 7 Component Processor (CP) ...................................................... 13 Absolute Maximum Ratings............................................................ 8 Analog Input Muxing ................................................................ 14 Package Thermal Performance ................................................... 8 Pixel Output Formatting................................................................ 16 Thermal Specifications ................................................................ 8 Recommended External Loop Filter Components .................... 17 ESD Caution .................................................................................. 8 Typical Connection Diagram ....................................................... 18 Pin Configuration and Function Descriptions ............................. 9 Outline Dimensions ....................................................................... 19 Detailed Functionality ................................................................... 11 Ordering Guide .......................................................................... 19 Analog Front End ....................................................................... 11 REVISION HISTORY 8/08—Revision 0: Initial Version Rev. 0 | Page 2 of 20 Figure 1. Rev. 0 | Page 3 of 20 SOG/SOY HS_IN/ CS_IN VS_IN ALSB SDATA SCLK FB CVBS S-VIDEO YPrPb SCART– (RGB + CVBS) GRAPHICS RGB AIN1 6 TO AIN6 ADC2 ADC3 ANTIALIAS FILTER ANTIALIAS FILTER CLAMP CLAMP CLAMP SSPD XTAL STDI SYNC PROCESSING AND CLOCK GENERATION ADC1 ANTIALIAS FILTER CLAMP ADC0 ANTIALIAS FILTER SERIAL INTERFACE CONTROL AND VBI DATA INPUT MUX ADV7181C 10 10 10 10 10 COLORSPACE CONVERSION 10 10 DECIMATION AND DOWNSAMPLING 10 FILTERS DATA PREPROCESSOR 10 10 10 Cb Cr C CVBS DIGITAL FINE CLAMP ACTIVE PEAK AND AGC CHROMA DEMOD FSC RECOVERY CVBS/Y MACROVISION DETECTION CHROMA RESAMPLE RESAMPLE CONTROL LUMA RESAMPLE GAIN CONTROL MACROVISION DETECTION OFFSET CONTROL CGMS DATA EXTRACTION Y Cb Cr Y Cr CHROMA 2D COMB Cb (4H MAX) LUMA 2D COMB (5H MAX) AV CODE INSERTION FAST BLANK OVERLAY CONTROL AND AV CODE INSERTION VBI DATA RECOVERY COMPONENT PROCESSOR CHROMA FILTER SYNC EXTRACT LUMA FILTER STANDARD AUTODETECTION STANDARD DEFINITION PROCESSOR 20 20 10 10 INT SFL/ SYNCOUT LLC FIELD/DE VS HS/CS P9 TO P0 P19 TO P10 PIXEL DATA ADV7181C FUNCTIONAL BLOCK DIAGRAM 07513-001 OUTPUT FIFO AND FORMATTER ADV7181C SPECIFICATIONS ELECTRICAL CHARACTERISTICS AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V, nominal input range 1.6 V. TMIN to TMAX = −40°C to +85°C, unless otherwise noted. Table 1. Parameter1, 2 STATIC PERFORMANCE3, 4 Resolution (each ADC) Integral Nonlinearity Differential Nonlinearity DIGITAL INPUTS5 Input High Voltage6 Symbol N INL DNL Test Conditions BSL at 27 MHz (10-bit level) BSL at 54 MHz (10-bit level) BSL at 74 MHz (10-bit level) BSL at 110 MHz (8-bit level) At 27 MHz (10-bit level) At 54 MHz (10-bit level) At 74 MHz (10-bit level) At 110 MHz (8-bit level) VIH HS_IN, VS_IN low trigger mode Input Low Voltage7 Min Typ ±0.6 −0.6/+0.7 ±1.4 ±0.9 −0.2/+0.25 −0.2/+0.25 ±0.9 −0.2/+1.5 HS_IN, VS_IN low trigger mode IIN CIN Output Capacitance5 POWER REQUIREMENTS5 Digital Core Power Supply Digital I/O Power Supply PLL Power Supply Analog Power Supply Digital Core Supply Current COUT DVDD DVDDIO PVDD AVDD IDVDD Digital I/O Supply Current IDVDDIO PLL Supply Current IPVDD Analog Supply Current9 IAVDD Power-Down Current Green Mode Power-Down Power-Up Time IPWRDN IPWRDNG TPWRUP VOH VOL ILEAK −10 ISOURCE = 0.4 mA ISINK = 3.2 mA Pin 1 All other output pins Synchronization bypass function 1 10 ±2.5 Bits LSB LSB LSB LSB LSB LSB LSB LSB −0.99/+2.5 0.8 0.3 +10 10 V V V V μA pF 0.4 60 10 20 V V μA μA pF 2.4 1.65 3.0 1.71 3.15 CVBS input sampling at 54 MHz Graphics RGB sampling at 110 MHz SCART RGB FB sampling at 54 MHz CVBS input sampling at 54 MHz Graphics RGB sampling at 110 MHz CVBS input sampling at 54 MHz Graphics RGB sampling at 110 MHz CVBS input sampling at 54 MHz Graphics RGB sampling at 110 MHz SCART RGB FB sampling at 54 MHz Unit 2 0.7 VIL Input Current Input Capacitance5 DIGITAL OUTPUTS Output High Voltage8 Output Low Voltage8 High Impedance Leakage Current Max 1.8 3.3 1.8 3.3 105 113 106 4 16 11 12 99 198 269 2.25 16 20 2 3.6 1.89 3.45 V V V V mA mA mA mA mA mA mA mA mA mA mA mA ms The minimum/maximum specifications are guaranteed over this range. All specifications are obtained using the Analog Devices, Inc., recommended programming scripts. 3 All ADC linearity tests performed at input range of full scale – 12.5%, and at zero scale + 12.5%. 4 Maximum INL and DNL specifications obtained with part configured for component video input. 5 Guaranteed by characterization. 6 To obtain specified VIH level on Pin 22, program Register 0x13 (WO) with a value of 0x04. If Register 0x13 is programmed with a value of 0x00, then VIH on Pin 22 is 1.2 V. 7 To obtain specified VIL level on Pin 22, program Register 0x13 (WO) with a value of 0x04. If Register 0x13 is programmed with a value of 0x00, then VIL on Pin 22 is 0.4 V. 8 VOH and VOL levels obtained using default drive strength value (0xD5) in Register Subaddress 0xF4. 9 For CVBS current measurement only, ADC0 is powered up. For RGB current measurements only, ADC0, ADC1, and ADC2 are powered up. For SCART FB current measurements, all ADCs are powered up. 2 Rev. 0 | Page 4 of 20 ADV7181C VIDEO SPECIFICATIONS AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V. TMIN to TMAX = −40°C to +85°C, unless otherwise noted. Table 2. Parameter 1, 2 NONLINEAR SPECIFICATIONS Differential Phase Differential Gain Luma Nonlinearity NOISE SPECIFICATIONS SNR Unweighted SNR Unweighted Analog Front-End Crosstalk LOCK TIME SPECIFICATIONS Horizontal Lock Range Vertical Lock Range FSC Subcarrier Lock Range Color Lock in Time Sync Depth Range 3 Color Burst Range Vertical Lock Time Horizontal Lock Time CHROMA SPECIFICATIONS Hue Accuracy Color Saturation Accuracy Color AGC Range Chroma Amplitude Error Chroma Phase Error Chroma Luma Intermodulation LUMA SPECIFICATIONS Luma Brightness Accuracy Luma Contrast Accuracy 1 2 3 Symbol Test Conditions DP DG LNL CVBS input, modulated 5 step CVBS input, modulated 5 step CVBS input, 5 step Luma ramp Luma flat field Min 54 58 Typ Max 0.5 0.5 0.5 Degrees % % 56 60 60 dB dB dB −5 40 +5 70 ±1.3 60 20 5 200 200 2 100 HUE CL_AC 1 1 The minimum/maximum specifications are guaranteed over this range. Guaranteed by characterization. Nominal synchronization depth is 300 mV at 100% synchronization depth range. Rev. 0 | Page 5 of 20 % Hz kHz Lines % % Fields Lines 0.5 0.4 0.2 Degrees % % % Degrees % 1 1 % % 5 CVBS, 1 V input CVBS, 1 V input Unit 400 ADV7181C TIMING CHARACTERISTICS AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V. TMIN to TMAX = −40°C to +85°C, unless otherwise noted. Table 3. Parameter 1, 2 SYSTEM CLOCK AND CRYSTAL Crystal Nominal Frequency Crystal Frequency Stability LLC Frequency Range 3 I2C PORT 4 SCLK Frequency SCLK Min Pulse Width High SCLK Min Pulse Width Low Hold Time (Start Condition) Setup Time (Start Condition) SDA Setup Time SCLK and SDA Rise Time SCLK and SDA Fall Time Setup Time for Stop Condition RESET FEATURE Reset Pulse Width CLOCK OUTPUTS LLC Mark Space Ratio DATA and CONTROL OUTPUTS Data Output Transition Time SDR (SDP) 5 Symbol Test Conditions Min Typ Max Unit ±50 110 MHz ppm MHz 28.63636 12.825 400 t1 t2 t3 t4 t5 t6 t7 t8 0.6 1.3 0.6 0.6 100 300 300 0.6 5 t9:t10 t11 Data Output Transition Time SDR (SDP)5 t12 Data Output Transition Time SDR (CP) 6 t13 Data Output Transition Time SDR (CP)6 t14 Data Output Transition Time DDR (CP)6, 7 t15 Data Output Transition Time DDR (CP)6, 7 t16 Data Output Transition Time DDR (CP)6, 7 t17 Data Output Transition Time DDR (CP)6, 7 t18 45:55 Negative clock edge to start of valid data End of valid data to negative clock edge End of valid data to negative clock edge Negative clock edge to start of valid data Positive clock edge to end of valid data Positive clock edge to start of valid data Negative clock edge to end of valid data Negative clock edge to start of valid data 1 3 Rev. 0 | Page 6 of 20 ms 55:45 % duty cycle 3.6 ns 2.4 ns 2.8 ns 0.1 ns −4 + TLLC/4 ns 0.25 + TLLC/4 ns −2.95 + TLLC/4 ns −0.5 + TLLC/4 ns The minimum/maximum specifications are guaranteed over this range. Guaranteed by characterization. Maximum LLC frequency is 110 MHz. 4 TTL input values are 0 V to 3 V, with rise/fall times of ≤3 ns, measured between the 10% and 90% points. 5 SDP timing figures obtained using default drive strength value (0xD5) in Register Subaddress 0xF4. 6 CP timing figures obtained using maximum drive strength value (0xFF) in Register Subaddress 0xF4. 7 DDR timing specifications dependent on LLC output pixel clock; TLCC/4 = 9.25 ns at LLC = 27 MHz. 2 kHz μs μs μs μs ns ns ns μs ADV7181C ANALOG SPECIFICATIONS AVDD = 3.1.5 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V. TMIN to TMAX = −40°C to +85°C, unless otherwise noted. Recommended analog input video signal range: 0.5 V to 1.6 V, typically 1 V p-p. Table 4. Parameter 1, 2 CLAMP CIRCUITRY External Clamp Capacitor Input Impedance; Except Pin 34 (FB) Input Impedance of Pin 34 (FB) CML ADC Full-Scale Level ADC Zero-Scale level ADC Dynamic Range Clamp Level (When Locked) Large Clamp Source Current Large Clamp Sink Current Fine Clamp Source Current Fine Clamp Sink Current 1 2 Test Conditions Clamps switched off CVBS input SCART RGB input (R, G, B signals) S-Video input (Y signal) S-Video input (C signal) Component input (Y, Pr, Pb signals) PC RGB input (R, G, B signals) SDP only SDP only SDP only SDP only The minimum/maximum specifications are guaranteed over this range. Guaranteed by characterization. Rev. 0 | Page 7 of 20 Min Typ 0.1 10 20 1.86 CML + 0.8 V CML − 0.8 V 1.6 CML – 0.292 V CML – 0.4 V CML – 0.292 V CML – 0 V CML – 0.3 V CML – 0.3 V 0.75 0.9 17 17 Max Unit μF MΩ kΩ V V V V V V V V V V mA mA μA μA ADV7181C ABSOLUTE MAXIMUM RATINGS PACKAGE THERMAL PERFORMANCE Table 5. Parameter AVDD to AGND DVDD to DGND PVDD to AGND DVDDIO to DGND DVDDIO to AVDD PVDD to DVDD DVDDIO to PVDD DVDDIO to DVDD AVDD to PVDD AVDD to DVDD Digital Inputs Voltage to DGND Digital Outputs Voltage to DGND Analog Inputs to AGND Operating Temperature Maximum Junction Temperature (TJ MAX) Storage Temperature Range Infrared Reflow Soldering (20 sec) Rating 4V 2.2 V 2.2 V 4V −0.3 V to +0.3 V −0.3 V to +0.3 V −0.3 V to +2 V −0.3 V to +2 V −0.3 V to +2 V −0.3 V to +2 V DGND − 0.3 V to DVDDIO + 0.3 V DGND − 0.3 V to DVDDIO + 0.3 V AGND − 0.3 V to AVDD + 0.3 V −40°C to +85°C 125°C −65°C to +150°C 260°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. To reduce power consumption when using the part the user is advised to turn off any unused ADCs. It is imperative that the recommended scripts be used for the following high current modes: SCART, 720p, 1080i, and all RGB graphic standards. Using the recommended scripts ensures correct thermal performance. These scripts are available from a local FAE. The junction temperature must always stay below the maximum junction temperature (TJ MAX) of 125°C. Using the following equation, calculate the junction temperature: TJ = TA MAX + (θJA × WMAX) where: TA MAX = 85°C. θJA = 45.5°C/W. WMAX = ((AVDD × IAVDD) + (DVDD × IDVDD) + (DVDDIO × IDVDDIO) + (PVDD × IPVDD)). THERMAL SPECIFICATIONS Table 6. Package Type 64-Lead LQFP 64-Lead LFCSP_VQ 1 2 θJA1 45.5 20.3 4-layer PCB with solid ground plane (still air). 4-layer PCB with solid ground plane. ESD CAUTION Rev. 0 | Page 8 of 20 θJC2 9.2 1.2 Unit °C/W °C/W ADV7181C 64 63 62 61 60 59 58 AIN6 SOG/SOY RESET ALSB SDATA SCLK VS_IN HS_IN/CS_IN DGND DVDD P19 P18 P17 P16 FIELD/DE VS PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 57 56 55 54 53 52 51 50 49 INT 1 HS/CS 2 48 AIN5 DGND 3 46 AIN3 DVDDIO 4 45 NC P15 5 44 CAPC2 P14 6 43 AGND P13 7 P12 8 SFL/SYNC_OUT 9 PIN 1 47 AIN4 42 CML ADV7181C 41 REFOUT TOP VIEW (Not to Scale) DGND 10 40 AVDD 39 CAPY2 DVDDIO 11 38 CAPY1 P11 12 37 AGND P10 13 36 AIN2 P9 14 35 AIN1 P8 15 34 FB P7 16 33 NC NOTES 1. NC = NO CONNECT. 2. THE LFCSP_VQ HAS AN EXPOSED PADDLE THAT MUST BE CONNECTED TO GND. 07513-002 AGND PVDD ELPF PWRDWN P0 P1 P2 P3 DGND DVDD XTAL XTAL1 LLC P4 P5 P6 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Figure 2. Pin Configuration Table 7. Pin Function Descriptions Pin No. 3, 10, 24, 57 32, 37, 43 4, 11 23, 58 40 31 34 35, 36, 46, 47, 48, 49 28 to 25, 19 to 12, 8 to 5, 62 to 59 1 Mnemonic DGND AGND DVDDIO DVDD AVDD PVDD FB AIN1 to AIN6 P0 to P19 Type 1 G G P P P P I I O Description Digital Ground. Analog Ground. Digital I/O Supply Voltage (3.3 V). Digital Core Supply Voltage (1.8 V). Analog Supply Voltage (3.3 V). PLL Supply Voltage (1.8 V). Fast Switch Overlay Input. This pin switches between CVBS and RGB analog signals. Analog Video Input Channels. Video Pixel Output Port. Refer to Table 10 for output configuration modes. INT O 2 HS/CS O 64 63 VS FIELD/DE O O 53 54 52 SDATA SCLK ALSB I/O I I Interrupt. This pin can be active low or active high. When SDP/CP status bits change, this pin is triggered. The set of events that triggers an interrupt is under user control. HS: Horizontal Synchronization Output Signal (SDP and CP Modes). CS: Digital Composite Synchronization Signal (CP Mode). Vertical Synchronization Output Signal (SDP and CP Modes). Field Synchronization Output Signal (All Interlaced Video Modes). This pin also can be enabled as an data enable signal (DE) in CP mode to allow direct connection to a HDMI/DVI Tx IC. I2C Port Serial Data Input/Output Pin. I2C Port Serial Clock Input. Maximum clock rate of 400 kHz. This pin selects the I2C address for the ADV7181C control and VBI readback ports. ALSB set to Logic 0 sets the address for a write to Control Port 0x40 and the readback address for VBI Port 0x21. ALSB set to a Logic 1 sets the address for a write to Control Port 0x42 and the readback address for VBI Port 0x23. Rev. 0 | Page 9 of 20 ADV7181C Pin No. 51 Mnemonic RESET Type 1 I 20 LLC O 22 XTAL I 21 XTAL1 O 30 9 ELPF SFL/SYNC_OUT O O 41 REFOUT O 42 CML O 38, 39 CAPY1, CAPY2 I 44 CAPC2 I 56 HS_IN/CS_IN I 55 50 29 33, 45 VS_IN SOG/SOY PWRDWN NC I I I 1 Description System Reset Input, Active Low. A minimum low reset pulse width of 5 ms is required to reset the ADV7181C circuitry. Line-Locked Output Clock. This pin is for the pixel data (the range is 12.825 MHz to 110 MHz). Input pin for 28.63636 MHz crystal, or can be overdriven by an external 3.3 V, 28.63636 MHz clock oscillator source to clock the ADV7181C. This pin should be connected to the 28.63636 MHz crystal or left as a no connect if an external 3.3 V, 28.63636 MHz clock oscillator source is used to clock the ADV7181C. In crystal mode, the crystal must be a fundamental crystal. The recommended external loop filter must be connected to this ELPF pin. SFL: Subcarrier Frequency Lock. This pin contains a serial output stream that can be used to lock the subcarrier frequency when this decoder is connected to any Analog Devices digital video encoder. SYNC_OUT: Sliced Synchronization Output Signal Available Only in CP Mode. Internal Voltage Reference Output. See Figure 5 for a recommended capacitor network for this pin. Common-Mode Level Pin (CML) for the Internal ADCs. See Figure 5 for a recommended capacitor network for this pin. ADC Capacitor Network. See Figure 5 for a recommended capacitor network for this pin. ADC Capacitor Network. See Figure 5 for a recommended capacitor network for this pin. This pin can be configured in CP mode to be either a digital HS input signal or a digital CS input signal used to extract timing in a 5-wire or 4-wire RGB mode. VS Input Signal. Used in CP mode for 5-wire timing mode. Sync on Green/Sync on Luma Input. Used in embedded synchronization mode. A Logic 0 on this pin places the ADV7181C in a power-down mode. No Connect. These pins are not connected internally. G = ground, I = input, O = output, I/O = input/output. Rev. 0 | Page 10 of 20 ADV7181C DETAILED FUNCTIONALITY ANALOG FRONT END COMPOSITE AND S-VIDEO PROCESSING The analog front-end section contains four high quality 10-bit ADCs, and the six analog input channel mux enables multisource connection without the requirement of an external mux. It also contains Composite and S-Video processing features offer support for NTSC M/J, NTSC 4.43, PAL B/D/I/G/H, PAL60, PAL M, PAL N, and SECAM (B, D, G, K, and L) standards in the form of CVBS and S-Video as well as super-adaptive, 2D, 5-line comb filters for NTSC and PAL give superior chrominance and luminance separation for composite video. They also include full automatic detection and autoswitching of all worldwide standards (PAL, NTSC, and SECAM) and automatic gain control with white peak mode to ensure the video is always processed without loss of the video processing range. Other features are • • • Four current and voltage clamp control loops to ensure that any dc offsets are removed from the video signal SCART functionality and SD RGB overlay on CVBS that are controlled by fast blank input Four internal antialias filters to remove out-of-band noise on standard definition input video signals SDP PIXEL DATA OUTPUT MODES • • 8-/10-bit ITU-R BT.656 4:2:2 YCrCb with embedded time codes and/or HS, S, and FIELD 16-/20-bit YCrCb with embedded time codes and/or HS, VS, and FIELD CP PIXEL DATA OUTPUT MODES CP pixel data output modes include single data rate (SDR) and double data rate (DDR) as follows: • • • • SDR 8-/10-bit 4:2:2 YCrCb for 525i, 625i SDR 16-/20-bit 4:2:2 YCrCb for all standards DDR 8-/10-bit 4:2:2 YCrCb for all standards DDR 12-bit 4:4:4 RGB for graphics inputs • • • • • • • • • • • • • • • • Rev. 0 | Page 11 of 20 Adaptive Digital Line Length Tracking (ADLLT™) Proprietary architecture for locking to weak, noisy, and unstable sources from VCRs and tuners IF filter block to compensate for high frequency luma attenuation due to tuner SAW filter Chroma transient improvement (CTI) Luminance digital noise reduction (DNR) Color controls including hue, brightness, saturation, contrast, and Cr and Cb offset controls Certified Macrovision® copy protection detection on composite and S-Video for all worldwide formats (PAL/NTSC/SECAM) 4× oversampling (54 MHz) for CVBS, S-Video, and YUV modes Line-locked clock output (LLC) Letterbox detection support Free-run output mode to provide stable timing when no video input is present Vertical blanking interval data processor, including teletext, video programming system (VPS), vertical interval time codes (VITC), closed captioning (CC) and extended data service (EDS), wide screen signaling (WSS), copy generation management system (CGMS), and compatibility with GemStar™ 1×/2× electronic program guide Clocked from a single 28.63636 MHz crystal Subcarrier frequency lock (SFL) output for downstream video encoder Differential gain typically 0.5% Differential phase typically 0.5° ADV7181C COMPONENT VIDEO PROCESSING GENERAL FEATURES Component video processing supports formats including 525i, 625i, 525p, 625p, 720p, 1080i, and many other HDTV formats, as well as automatic adjustments that include gain (contrast) and offset (brightness), and manual adjustment controls. Other features supported by component video processing are General features of the ADV7181C include HS/CS, VS, and FIELD/DE output signals with programmable position, polarity, and width as well as a programmable interrupt request output pin, INT, that signals SDP/CP status changes. Other features are • • • • • • • Analog component YPrPb/RGB video formats with embedded synchronization or with separate HS, VS, or CS Color space conversion matrix to support YCrCb-to-DDR RGB and RGB-to-YCrCb Standard identification (STDI) enables system level component format detection Synchronization source polarity detector (SSPD) to determine the source and polarity of the synchronization signals that accompany the input video Certified Macrovision copy protection detection on component formats (525i, 625i, 525p, and 625p) Free-run output mode to provide stable timing when no video input is present Arbitrary pixel sampling support for nonstandard video sources • • • • RGB GRAPHICS PROCESSING RGB graphics processing offers a 110 MSPS conversion rate that supports RGB input resolutions up to 1280 × 1024 at 60 Hz (SXGA), automatic or manual clamp and gain controls for graphics modes, and contrast and brightness controls. Other features include • • • • • • • 32-phase DLL to allow optimum pixel clock sampling Automatic detection of synchronization source and polarity by SSPD block Standard identification enabled by the STDI block RGB that can be color space converted to YCrCb and decimated to a 4:2:2 format for video centric back-end IC interfacing Data enable (DE) output signal supplied for direct connection to HDMI/DVI Tx IC Arbitrary pixel sampling support for nonstandard video sources RGB graphics supported on 12-bit DDR format Rev. 0 | Page 12 of 20 Low power consumption: 1.8 V digital core, 3.3 V analog and digital I/O, low power, power-down mode, and green PC mode Industrial temperature range of −40°C to +85°C 64-lead, 10 mm × 10 mm, Pb-free LQFP 3.3 V ADCs giving enhanced dynamic range and performance ADV7181C DETAILED DESCRIPTION ANALOG FRONT END The ADV7181C analog front end comprises four 10-bit ADCs that digitize the analog video signal before applying it to the SDP or CP. The analog front end uses differential channels to each ADC to ensure high performance in a mixed-signal application. The front end also includes a 6-channel input mux that enables multiple video signals to be applied to the ADV7181C. Current and voltage clamps are positioned in front of each ADC to ensure that the video signal remains within the range of the converter. Fine clamping of the video signals is performed downstream by digital fine clamping in either the CP or SDP. Optional antialiasing filters are positioned in front of each ADC. These filters can be used to band-limit standard definition video signals, removing spurious out-of-band noise. The ADCs are configured to run in 4× oversampling mode when decoding composite and S-Video inputs; 2× oversampling is performed for component 525i, 625i, 525p, and 625p sources. All other video standards are 1× oversampled. Oversampling the video signals reduces the cost and complexity of external antialiasing filters with the benefit of an increased signal-tonoise ratio (SNR). The ADV7181C can support simultaneous processing of CVBS and RGB standard definition signals to enable SCART compatibility and overlay functionality. A combination of CVBS and RGB inputs can be mixed and output under the control of the I2C registers and the fast blank pin. STANDARD DEFINITION PROCESSOR (SDP) The SDP section is capable of decoding a large selection of baseband video signals in composite S-Video and YUV formats. The video standards supported by the SDP include PAL B/D/I/G/H, PAL60, PAL M, PAL N, NTSC M/J, NTSC 4.43, and SECAM B/D/G/K/L. The ADV7181C automatically detects the video standard and processes it accordingly. The SDP has a 5-line super adaptive 2D comb filter that gives superior chrominance and luminance separation when decoding a composite video signal. This highly adaptive filter automatically adjusts its processing mode according to video standards and signal quality with no user intervention required. The SDP has an IF filter block that compensates for attenuation in the high frequency luma spectrum due to the tuner SAW filter. The SDP has specific luminance and chrominance parameter control for brightness, contrast, saturation, and hue. The ADV7181C implements a patented Adaptive-Digital-LineLength-Tracking (ADLLT) algorithm to track varying video line lengths from sources such as a VCR. ADLLT enables the ADV7181C to track and decode poor quality video sources such as VCRs, noisy sources from tuner outputs, VCD players, and camcorders. The SDP also contains a chroma transient improvement (CTI) processor. This processor increases the edge rate on chroma transitions, resulting in a sharper video image. The SDP can process a variety of VBI data services, such as teletext, closed captioning (CC), wide screen signaling (WSS), video programming system (VPS), vertical interval time codes (VITC), copy generation management system (CGMS), GemStar 1×/2×, and extended data service (XDS). The ADV7181C SDP section has a Macrovision 7.1 detection circuit that allows it to detect Type I, Type II, and Type III protection levels. The decoder is also fully robust to all Macrovision signal inputs. COMPONENT PROCESSOR (CP) The CP section is capable of decoding/digitizing a wide range of component video formats in any color space. Component video standards supported by the CP are 525i, 625i, 525p, 625p, 720p, 1080i, graphics up to SXGA at 60 Hz, and many other standards. The CP section of the ADV7181C contains an AGC block. When no embedded synchronization is present, the video gain can be set manually. The AGC section is followed by a digital clamp circuit that ensures the video signal is clamped to the correct blanking level. Automatic adjustments within the CP include gain (contrast) and offset (brightness); manual adjustment controls are also supported. A fixed mode graphics RGB to component output is available. A color space conversion matrix is placed between the analog front end and the CP section. This enables YPrPb-to-DDR RGB and RGB-to-YCrCb conversions. Many other standards of color space can be implemented using the color space converter. The output section of the CP is highly flexible. It can be configured in SDR mode with one data packet per clock cycle or in a DDR mode where data is presented on the rising and falling edges of the clock. In SDR mode, a 20-bit 4:2:2 is possible. In these modes, HS/CS, VS, and FIELD/DE (where applicable) timing reference signals are provided. In DDR mode, the ADV7181C can be configured in an 8-bit 4:2:2 YCrCb or 12-bit 4:4:4 RGB pixel output interface with corresponding timing signals. The CP section contains circuitry to enable the detection of Macrovision encoded YPrPb signals for 525i, 625i, 525p, and 625p. It is designed to be fully robust when decoding these types of signals. VBI extraction of component data is performed by the CP section of the ADV7181C for interlaced, progressive, and high definition scanning rates. The data extracted can be read back over the I2C interface. Rev. 0 | Page 13 of 20 ADV7181C ANALOG INPUT MUXING AIN5 AIN6 ADC_SW_MAN_EN 1 ADC0_SW[3:0] AIN1 AIN2 AIN3 ADC0 AIN4 AIN5 AIN6 1 ADC1_SW[3:0] AIN3 AIN4 AIN5 ADC1 AIN6 1 ADC2_SW[3:0] AIN2 AIN4 AIN5 AIN6 ADC2 1 ADC3_SW[3:0] AIN4 ADC3 Figure 3. ADV7181C Internal Pin Connections Rev. 0 | Page 14 of 20 07513-003 AIN4 AIN3 AIN2 AIN1 The ADV7181C has an integrated analog muxing section that allows more than one source of video signal to be connected to the decoder. Figure 3 outlines the overall structure of the input muxing provided in the ADV7181C. ADV7181C On the ADV7181C, it is recommended to use the ADC mapping shown in Table 8. Table 8. Recommended ADC Mapping Mode CVBS Required ADC Mapping ADC0 AIN Channel CVBS = AIN1 Core SD YC/YC auto Y = ADC0 C = ADC1 Y = AIN2 C = AIN3 SD Component YUV Y = ADC0 U = ADC2 V = ADC1 Y = AIN6 U = AIN4 V = AIN5 SD Component YUV Y = ADC0 U = ADC2 V = ADC1 Y = AIN6 U = AIN4 V = AIN5 CP SCART RGB CBVS = ADC0 G = ADC1 B = ADC3 R = ADC2 G = ADC0 B = ADC2 R = ADC1 CVBS = AIN2 G = AIN6 B = AIN4 R = AIN5 G = AIN6 B = AIN4 R = AIN5 SD Graphics RGB Mode 1 CP Configuration 1 INSEL[3:0] = 0000 SDM_SEL[1:0] = 00 PRIM_MODE[3:0] = 0000 VID_STD[3:0] = 0010 INSEL[3:0] = 0000 SDM_SEL[1:0] = 11 PRIM_MODE[3:0] = 0000 VID_STD[3:0] = 0010 INSEL[3:0] = 1001 SDM_SEL[1:0] = 00 PRIM_MODE[3:0] = 0000 VID_STD[3:0] = 0010 INSEL[3:0] = 0000 SDM_SEL[1:0] = 00 PRIM_MODE[3:0] = 0000 VID_STD[3:0] = 1010 INSEL[3:0] = 0000 SDM_SEL[1:0] = 00 PRIM_MODE[3:0] = 0000 VID_STD[3:0] = 0010 INSEL[3:0] = 0000 SDM_SEL[1:0] = 00 PRIM_MODE[3:0] = 0001 VID_STD[3:0] = 1100 Configuration to format follow-on blocks in correct format. Table 9. Manual MUX Settings for All ADCs ADC0_SW_SEL[3:0] 0001 0010 0100 0101 0110 1100 ADC0 Connection AIN1 AIN2 AIN4 AIN5 AIN6 AIN3 ADC1_SW_SEL[3:0] 0001 0010 0100 0101 0110 1100 ADC_SWITCH_MAN to 1 ADC1 Connection ADC2_SW_SEL[3:0] N/A 0001 N/A 0010 AIN4 0100 AIN5 0101 AIN6 0110 AIN3 1100 The analog input muxes of the ADV7181C must be controlled directly. This is referred to as manual input muxing. The manual muxing is activated by setting the ADC_SWITCH_MAN bit (see Table 9). It affects only the analog switches in front of the ADCs. INSEL, SDM_SEL, PRIM_MODE, and VID_STD still have to be set so that the follow-on blocks process the video data in the correct format. Not every input pin can be routed to any ADC. There are restrictions in the channel routing imposed by the analog signal routing inside the IC. See Table 9 for an overview of the routing capabilities inside the chip. The three mux sections can be controlled by the reserved control signal buses ADC0_SW[3:0]/ ADC1_SW[3:0]/ADC2_SW[3:0]. ADC2 Connection N/A AIN2 AIN4 AIN5 AIN6 N/A ADC3_SW_SEL[3:0] 0001 0010 0100 0101 0110 1100 ADC3 Connection N/A N/A AIN4 N/A N/A N/A Table 9 explains the ADC mapping configuration for the following: • • • • • Rev. 0 | Page 15 of 20 ADC_SWITCH_MAN, manual input muxing enable, IO map, Address 0C[7] ADC0_SW[3:0], ADC0 mux configuration, IO map, Address 0D[3:0] ADC1_SW[3:0], ADC1 mux configuration, IO map, Address 0D[7:4] ADC2_SW[3:0], ADC2 mux configuration, IO map, Address 0E[3:0] ADC3_SW[3:0], ADC3 mux configuration, IO map, Address 0E[7:4] ADV7181C PIXEL OUTPUT FORMATTING Table 10. Pixel Output Formats Processor, Format, and Mode Video output SDP 8-bit 4:2:2 Video output SDP 10-bit 4:2:2 Video output SDP 16-bit 4:2:2 Video output SDP 20-bit 4:2:2 Video output CP 12-bit 4:4:4 RGB DDR Video output CP 16-bit 4:2:2 Video output CP 20-bit 4:2:2 1 Pixel Port Pins P[19:0] 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 YCrCb[7:0] YCrCb[9:0] Y[7:0] CrCb[7:0] Y[9:0] 1 CrCb[7:0] 1 1 1 1 1 1 1 D7 D6 D5 D4 D3 D2 D1 D0 B[7]↑ B[6]↑ B[5]↑ B[4]↑ B[3]↑ B[2]↑ B[1]↑ B[0]↑ R[3]↓ R[2]↓ R[1]↓ R[0]↓ G[7]↓ G[6]↓ G[5]↓ G[4]↓ D111 D101 D91 D81 G[3]↑ G[2]↑ G[1]↑ G[0]↑ R[7]↓ R[6]↓ R[5]↓ R[4]↓ CHA[7:0] (for example, Y[7:0]) CHB/C[7:0] (for example, Cr/Cb[7:0]) CHA[9:0] (for example, Y[9:0]) CHB/C[9:0] (for example, Cr/Cb[9:0]) ↑ indicates data clocked on the rising edge of LLC, ↓ indicates data clocked on the falling edge of LLC. Rev. 0 | Page 16 of 20 3 2 1 0 ADV7181C RECOMMENDED EXTERNAL LOOP FILTER COMPONENTS The external loop filter components for the ELPF pin should be placed as close as possible to the respective pins. Figure 4 shows the recommended component values. ELPF 30 1.69kΩ 10nF PVDD = 1.8V 07513-004 82nF Figure 4. ELPF Components Rev. 0 | Page 17 of 20 ADV7181C TYPICAL CONNECTION DIAGRAM 07513-005 Figure 5. ADV7181C Typical Connection Rev. 0 | Page 18 of 20 ADV7181C OUTLINE DIMENSIONS 0.75 0.60 0.45 12.20 12.00 SQ 11.80 1.60 MAX 64 49 1 48 PIN 1 10.20 10.00 SQ 9.80 TOP VIEW (PINS DOWN) 1.45 1.40 1.35 0.15 0.05 SEATING PLANE 0.20 0.09 7° 3.5° 0° 16 33 32 17 0.08 COPLANARITY VIEW A VIEW A 0.27 0.22 0.17 0.50 BSC LEAD PITCH 051706-A ROTATED 90° CCW COMPLIANT TO JEDEC STANDARDS MS-026-BCD Figure 6. 64-Lead Low Profile Quad Flat Package [LQFP] (ST-64) Dimensions shown in millimeters 0.60 MAX 9.00 BSC SQ 0.60 MAX 64 1 49 48 PIN 1 INDICATOR PIN 1 INDICATOR 0.50 BSC 0.50 0.40 0.30 1.00 0.85 0.80 SEATING PLANE 16 17 33 32 FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 0.05 MAX 0.02 NOM 0.30 0.23 0.18 0.25 MIN 7.50 REF 0.80 MAX 0.65 TYP 12° MAX 7.25 7.10 SQ 6.95 EXPOSED PAD (BOTTOM VIEW) 0.20 REF COMPLIANT TO JEDEC STANDARDS MO-220-VMMD-4 080108-C 8.75 BSC SQ TOP VIEW Figure 7. 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 9 mm × 9 mm Body, Very Thin Quad (CP-64-3) Dimensions shown in millimeters ORDERING GUIDE Model ADV7181CBCPZ 1 ADV7181CBCPZ-REEL1 ADV7181CBSTZ1 ADV7181CBSTZ-REEL1 ADV7181WBCPZ1 ADV7181WBCPZ-REEL1 ADV7181WBSTZ1 ADV7181WBSTZ_REEL1 1 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 64–Lead LFCSP_VQ 64-Lead LFCSP_VQ 64 –Lead LQFP 64–Lead LQFP 64-Lead LFCSP_VQ 64-Lead LFCSP_VQ 64–Lead LQFP 64 –Lead LQFP Z = RoHS Compliant Part. Rev. 0 | Page 19 of 20 Package Option CP-64-3 CP-64-3 ST-64 ST-64 CP-64-3 CP-64-3 ST-64 ST-64 ADV7181C Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. ©2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07513-0-8/08(0) Rev. 0 | Page 20 of 20