TOSHIBA TC74HCT7007AP

TC74HCT7007AP/AF
TOSHIBA CMOS Digital Integrated Circuit
Silicon Monolithic
TC74HCT7007AP,TC74HCT7007AF
Hex Buffer
The TC74HCT7007A is a high speed CMOS BUFFER
fabricated with silicon gate C2MOS technology.
It achieves the high speed operation similar to equivalent
LSTTL while maintaining the CMOS low power dissipation.
This device may be used as a level converter for interfacing
TTL or NMOS to High Speed CMOS. The inputs are compatible
with TTL, NMOS and CMOS output voltage levels.
The internal circuit is composed of 4 stages including a buffer
output, which provides high noise immunity and stable output.
All inputs are equipped with protection circuits against static
discharge or transient excess voltage.
TC74HCT7007AP
TC74HCT7007AF
Features
•
High speed: tpd = 11 ns (typ.) at VCC = 5 V
•
Low power dissipation: ICC = 1 μA (max) at Ta = 25°C
•
Compatible with TTL outputs: VIH = 2 V (min)
•
Wide interfacing ability: LSTTL, NMOS, CMOS
•
Output drive capability: 10 LSTTL loads
•
Symmetrical output impedance: |IOH| = IOL = 4 mA (min)
•
Balanced propagation delays: tpLH ≈ tpHL
•
Pin and function compatible with 74LS07
VIL = 0.8 V (max)
Weight
DIP14-P-300-2.54
SOP14-P-300-1.27A
: 0.96 g (typ.)
: 0.18 g (typ.)
Pin Assignment
IEC Logic Symbol
1
2007-10-01
TC74HCT7007AP/AF
Truth Table
A
Y
L
L
H
H
Absolute Maximum Ratings (Note 1)
Characteristics
Symbol
Rating
Unit
Supply voltage range
VCC
−0.5~7
V
DC input voltage
VIN
−0.5~VCC + 0.5
V
DC output voltage
VOUT
−0.5~VCC + 0.5
V
Input diode current
IIK
±20
mA
Output diode current
IOK
±20
mA
DC output current
IOUT
±25
mA
DC VCC/ground current
ICC
±50
mA
Power dissipation
PD
500 (DIP) (Note 2)/180 (SOP)
mW
Storage temperature
Tstg
−65~150
°C
Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or
even destruction.
Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly
even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute
maximum ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 2: 500 mW in the range of Ta = −40°C~65°C. From Ta = 65°C to 85°C a derating factor of −10 mW/°C shall be
applied until 300 mW.
Operating Ranges (Note)
Characteristics
Symbol
Rating
Unit
Supply voltage
VCC
4.5~5.5
V
Input voltage
VIN
0~VCC
V
VOUT
0~VCC
V
Operating temperature
Topr
−40~85
°C
Input rise and fall time
tr, tf
0~500
ns
Output voltage
Note:
The operating ranges must be maintained to ensure the normal operation of the device.
Unused inputs must be tied to either VCC or GND.
2
2007-10-01
TC74HCT7007AP/AF
Electrical Characteristics
DC Characteristics
Ta = 25°C
Test Condition
Characteristics
Symbol
Ta = −40~85°C
VCC
(V)
Min
Typ.
Max
Min
Max
Unit
High-level input
voltage
VIH
⎯
4.5~
5.5
2.0
⎯
⎯
2.0
⎯
V
Low-level input
voltage
VIL
⎯
4.5~
5.5
⎯
⎯
0.8
⎯
0.8
V
High-level output
voltage
VOH
IOH = −20 μA
VIN
= VIH or
IOH = −4 mA
VIL
4.5
4.4
4.5
⎯
4.4
⎯
4.5
4.18
4.31
⎯
4.13
⎯
Low-level output
voltage
VOL
IOL = 20 μA
VIN
= VIH or
IOL = 4 mA
VIL
4.5
⎯
0.0
0.1
⎯
0.1
4.5
⎯
0.17
0.26
⎯
0.33
IIN
VIN = VCC or GND
5.5
⎯
⎯
±0.1
⎯
±1.0
μA
ICC
VIN = VCC or GND
5.5
⎯
⎯
1.0
⎯
10.0
μA
5.5
⎯
⎯
2.0
⎯
2.9
mA
Test Condition
Min
Typ.
Max
Unit
⎯
⎯
6
12
ns
⎯
⎯
11
17
ns
Input leakage
current
Quiescent supply
current
Per input: VIN = 0.5 V or 2.4 V
IC
Other input: VCC or GND
V
V
AC Characteristics (CL = 15 pF, VCC = 5 V, Ta = 25°C, input: tr = tf = 6 ns)
Characteristics
Symbol
tTLH
Output transition time
tTHL
tpLH
Propagation delay time
tpHL
AC Characteristics (CL = 50 pF, input: tr = tf = 6 ns)
Ta = 25°C
Test Condition
Characteristics
Output transition time
Symbol
tTLH
tTHL
Propagation delay
time
tpLH
Input capacitance
CIN
Power dissipation
capacitance
CPD
Note:
tpHL
(Note)
Ta = −40~85°C
Unit
VCC
(V)
Min
Typ.
Max
Min
Max
4.5
⎯
8
15
⎯
19
5.5
⎯
7
14
⎯
18
4.5
⎯
14
23
⎯
28
5.5
⎯
12
21
⎯
26
⎯
⎯
5
10
⎯
10
pF
⎯
⎯
22
⎯
⎯
⎯
pF
⎯
⎯
ns
ns
CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating
current consumption without load.
Average operating current can be obtained by the equation:
ICC (opr) = CPD・VCC・fIN + ICC/6 (per gate)
3
2007-10-01
TC74HCT7007AP/AF
Package Dimensions
Weight: 0.96 g (typ.)
4
2007-10-01
TC74HCT7007AP/AF
Package Dimensions
Weight: 0.18 g (typ.)
5
2007-10-01
TC74HCT7007AP/AF
RESTRICTIONS ON PRODUCT USE
20070701-EN
• The information contained herein is subject to change without notice.
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.
• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his
document shall be made at the customer’s own risk.
• The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.
• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which
may result from its use. No license is granted by implication or otherwise under any patents or other rights of
TOSHIBA or the third parties.
• Product names mentioned herein may be trademarks of their respective companies.
• Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations
that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses
occurring as a result of noncompliance with applicable laws and regulations.
6
2007-10-01