Cherry CS3843BGD8 Off-line current mode pwm control circuit off-line current mode pwm control circuit Datasheet

CS3842B/3843B
CS3842B/CS3843B
Off-Line Current Mode PWM Control Circuit
with Very Low Start Up Current
Description
Features
possible. On board logic ensures that
VREF is stabilized before the output
stage is enabled. Ion-implant resistors
provide tighter control of undervoltage
lockout.
The CS384XB provides all the necessary features to implement off-line
fixed frequency current-mode control
with a minimum number of external
components. The family has been optimized for very low start up current
(300µA, typ).
Other features include pulse-by-pulse
current limiting, and a high-current
totem pole output for driving capacitive loads, such as the gate of a power
MOSFET. The output is LOW in the off
state, consistent with N-channel
devices.
The CS384XB family incorporates a
precision temperature-controlled oscillator with an internally trimmed discharge current to minimize variations
in frequency. A precision duty-cycle
clamp eliminates the need for an external oscillator when a 50% duty-cycle is
used. Duty-cycles of almost 100% are
These ICs are available in 8 and 14 lead
surface mount (SO) and 8 lead PDIP
packages.
Absolute Maximum Ratings
Supply Voltage (ICC<30mA) ..........................................................Self Limiting
Supply Voltage (Low Impedance Source)...................................................30V
Output Current ...............................................................................................±1A
Output Energy (Capacitive Load) .................................................................5µJ
Analog Inputs (VFB, Sense) ............................................................-0.3V to 5.5V
Error Amp Output Sink Current...............................................................10mA
Lead Temperature Soldering
Wave Solder (through hole styles only) ...................10 sec. max, 260°C peak
Reflow (SMD styles only) ....................60 sec. max above 183°C, 230°C peak
V CC
V CC Pwr
Undervoltage
Lock-out Circuit
34V
Set/
5V
Reset Reference
V REF
16V/10V
(8.4V/7.6V)
Internal
Bias
REF 2.50V
OSC
–
Error
Amplifier
1
8
VREF
VFB
2
7
VCC
Sense
3
6
VOUT
OSC
4
5
Gnd
COMP 1
14
VREF
NOR
V OUT
V FB
COMP
14L SO Narrow
Output
Enable
Oscillator
S
2 R
+
Package Options
8 Lead PDIP & SO Narrow
Block Diagram
Gnd
■ Very low Start Up Current
(300µA typ)
■ Optimized Off-line
Control
■ Internally Trimmed,
Temperature
Compensated Oscillator
■ Maximum Duty-cycle
Clamp
■ VREF stabilization before
Output Enable
■ Pulse-by-pulse Current
Limiting
■ Improved Undervoltage
Lockout
■ Double Pulse Suppression
■ 1% Trimmed Bandgap
Reference
■ High Current Totem Pole
Output
R
VC
R
1 V
COMP
PWM
Latch
Pwr Gnd
Current
Sense
Comparator
Sense
NC 2
13
NC
VFB 3
12
VCC
NC 4
11
VCC Pwr
Sense 5
10
VOUT
NC 6
9
Pwr Gnd
OSC 7
8
Gnd
( ) Indicates CS-3843B
Cherry Semiconductor Corporation
2000 South County Trail, East Greenwich, RI 02818
Tel: (401)885-3600 Fax: (401)885-5786
Email: [email protected]
Web Site: www.cherry-semi.com
Rev. 6/23/99
1
A
®
Company
CS3842B/3843B
Electrical Characteristics: 0≤TA≤70˚C, VCC=15V (Note 1); RT=680Ω, CT=.022µF for triangular mode,
RT=10kΩ, CT=3.3nF for sawtooth mode (see Fig. 3), unless otherwise stated
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
■ Reference Section
Output Voltage
TJ=25˚C, IOUT=1mA
5.00
5.10
V
Line Regulation
12≤VIN≤25V
6
20
mV
Load Regulation
1≤IOUT≤20mA
6
25
mV
Temperature Stability
(Note 2)
0.2
0.4
mV/˚C
Total Output Variation
Line, Load, Temperature (Note 2)
5.18
V
Output Noise Voltage
10Hz≤f≤10kHz, TJ=25˚C (Note 2)
4.90
4.82
50
µV
Long Term Stability
TA=125˚C, 1kHrs. (Note 2)
5
25
mV
Output Short Circuit
TA=25˚C
-30
-100
-180
mA
Initial Accuracy
Sawtooth Mode (see Fig. 3), TJ=25˚C
Triangular Mode (see Fig. 3), TJ=25˚C
47
44
52
52
57
60
kHz
kHz
Voltage Stability
12≤VCC≤25V
0.2
1.0
%
Temp. Stability
Sawtooth Mode TMIN≤TA≤TMAX
(Note 2)
Triangular Mode TMIN≤TA≤TMAX
(Note 2)
■ Oscillator Section
5
%
8
%
1.7
V
Amplitude
Oscillator peak to peak
Discharge Current
TJ=25˚C
TMIN≤TA≤TMAX
7.5
7.2
8.3
9.3
9.5
mA
mA
VCOMP=2.5V
2.42
2.50
2.58
V
-0.3
-2.0
µA
AVOL
2≤VOUT≤4V
65
90
dB
Unity Gain Bandwidth
(Note 2)
0.7
1.0
MHz
■ Error Amp Section
Input Voltage
Input Bias Current
PSRR
12≤VCC≤25V
60
70
dB
Output Sink Current
VFB=2.7V, VOSC=1.1V
2
6
mA
Output Source Current
VFB=2.3V, VOSC=5V
-0.5
-0.8
mA
VOUT High
VFB=2.3V, RL=15kΩ to ground
5
6
VOUT Low
VFB=2.7V, RL=15kΩ to VREF
V
0.7
1.1
V
■ Current Sense Section
Gain
(Notes 3 & 4)
2.85
3.00
3.15
V/V
Maximum Input Signal
VCOMP=5V (Note 3)
0.9
1.0
1.1
V
PSRR
12≤VCC≤25V (Note 3)
-2
-10
µA
TJ=25˚C (Note 2)
150
300
ns
Output Low Level
ISINK=20mA
ISINK=200mA
0.1
1.5
0.4
2.2
V
V
Output High Level
ISOURCE=20mA
ISOURCE=200mA
70
Input Bias Current
Delay to Output
dB
■ Output Section
13.0
12.0
2
13.5
13.5
V
V
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
■ Output Section: continued
Rise Time
TJ=25˚C, CL=1nF (Note 2)
50
150
ns
Fall Time
TJ=25˚C, CL=1nF (Note 2)
50
150
ns
Output Leakage
UVLO Active, VOUT=0
-0.01
-10.00
µA
0.3
0.5
mA
17
mA
■ Total Standby Current
Start-Up Current
Operating Supply Current
VFB=VSense=0V RT=10kΩ, CT=3.3nF
11
VCC Zener Voltage
ICC=25mA
34
V
CS-3842B
PARAMETER
TEST CONDITIONS
MIN
TYP
CS-3843B
MAX
MIN
TYP
MAX UNITS
■ Under-Voltage Lockout Section
Start Threshold
Min. Operating
Voltage
After Turn On
Notes: 1. Adjust VCC above the start threshold before setting at 15V.
14.5
16.0
17.5
7.8
8.4
9.0
V
8.5
10.0
11.5
7.0
7.6
8.2
V
3. Parameter measured at trip point of latch with VFB=0.
2. These parameters, although guaranteed, are not 100% tested
in production.
4.
Gain defined as:
A=
∆VCOMP
∆VSense
; 0 ≤ VSense ≤ 0.8V.
Package Pin Description
PACKAGE PIN #
PIN SYMBOL
FUNCTION
8L PDIP/SO
14L SO Narrow
1
1
COMP
2
3
VFB
3
5
Sense
Noninverting input to Current Sense Comparator
4
7
OSC
Oscillator Timing Network with Capacitor to Ground, resistor
to VREF
5
8
Gnd
Ground
9
Pwr Gnd
10
VOUT
11
VCCPwr
7
12
VCC
Positive power supply
8
14
VREF
Output of 5V internal reference
2,4,6,13
NC
No Connection
6
Error amp output, used to compensate error amplifier
Error amp inverting input
Output driver Ground
Output drive pin
Output driver positive supply
3
CS3842B/3843B
Electrical Characteristics: continued
CS3842B/3843B
Typical Performance Characteristics:
Oscillator Duty Cycle vs RT
Oscillator Frequency vs CT
100
900
90
800
80
RT =680Ω
DUTY CYCLE (%)
FREQ. (kHz)
700
600
500
RT =1.5kΩ
400
70
60
50
40
30
300
20
200
RT =10kΩ
10
100
100
.0005
.001
.002
.003
.005
.01
.02
200
300 400 500 700
1k
2k
3k 4k 5k
7k
10k
.03 .04 .05
RT (Ω)
CT (µF)
Test Circuit
V REF
RT
2N2222
V CC
A
100kΩ
COMP
4.7kΩ
0.1µF
CS-3842B
1kΩ
ERROR AMP
ADJUST
4.7kΩ
V REF
V FB
CS-3843B
V CC
0.1µF
5kΩ
V OUT
V OUT
Sense
Sense
ADJUST
1kΩ
1W
OSC
Gnd
Gnd
CT
Circuit Description
Undervoltage Lockout
V CC
During Undervoltage Lockout (Figure 1), the output driver is biased to a high impedance state. VOUT should be
shunted to ground with a resistor to prevent output leakage current from activating the power switch.
ON/OFF Command
to reset of IC
CS3842B CS3843B
V ON
V OFF
16V
10V
8.4V
7.6V
PWM Waveform
To generate the PWM waveform, the control voltage from
the error amplifier is compared to a current sense signal
which represents the peak output inductor current
(Figure 2). An increase in VCC causes the inductor current
slope to increase, thus reducing the duty cycle. This is an
inherent feed-forward characteristic of current mode control, since the control voltage does not have to change
during changes of input supply voltage.
When the power supply sees a sudden large output current increase, the control voltage will increase allowing
the duty cycle to momentarily increase. Since the duty
I CC
<15mA
<0.5mA
V CC
V ON
V OFF
Figure 1: Typical Undervoltage Characteristics
4
cycle tends to exceed the maximum allowed, to prevent
transformer saturation in some power supplies, the internal oscillator waveform provides the maximum duty cycle
clamp as programmed by the selection of oscillator timing
components.
VOSC
OSC
RESET
Setting the Oscillator
EA Output
The oscillator timing capacitor, CT, is charged by VREF
through RT and discharged by an internal current source
(Figure 3). During the discharge time, the internal clock
signal blanks out the output to the Low state, thus providing a user selected maximum duty cycle clamp.
Switch
Current
VCC
Charge and discharge times are determined by the general
formulas:
IOUT
VOUT
tc = RTCT ln
(
VREF – Vlower
VREF – Vupper
)
Figure 2: Timing Diagram for key CS-384XB parameters
td = RTCT ln
V REF
(
VREF – Id RT –Vlower
VREF – Id RT – Vupper
)
Substituting in typical values for the parameters in the
above formulas:
RT
OSC
CT
then
Gnd
VREF = 5.0V, Vupper = 2.7V, Vlower = 1.0V, Id = 8.3mA,
tc ≈ 0.5534RTCT
td = RTCT ln
Vupper
(
2.3 – 0.0083 RT
4.0 – 0.0083 RT
)
The frequency and maximum duty cycle can be determined from the Typical Performance Characteristics
graphs.
Vlower
tc
td
Grounding
High peak currents associated with capacitive loads necessitate careful grounding techniques. Timing and bypass
capacitors should be connected close to ground in a single
point ground.
Sawtooth Mode
LARGE RT (≈10kΩ)
VOSC
The transistor and 5kΩ potentiometer are used to sample
the oscillator waveform and apply an adjustable ramp to
Sense.
Internal Clock
Triangular Mode
SMALL RT (≈700kΩ)
VREF
Internal Clock
Figure 3: Oscillator Timing Network and parameters
5
CS3842B/3843B
Figure 3: Oscillator
CS3842B/3843B
Package Specification
PACKAGE THERMAL DATA
PACKAGE DIMENSIONS IN mm (INCHES)
Thermal Data
D
Lead Count
Metric
Max
Min
10.16
9.02
5.00
4.80
8.75
8.55
8 L PDIP
8 L SOIC Narrow
14L SOIC Narrow
English
Max Min
.400 .355
.197 .189
.344 .337
RΘJC
RΘJA
typ
typ
Surface Mount Narrow Body (D); 150 mil wide
Plastic DIP (N); 300 mil wide
7.11 (.280)
6.10 (.240)
6.20 (.244)
5.80 (.228)
4.00 (.157)
3.80 (.150)
8L
8L
14 L
PDIP SO Narrow SO Narrow
52
45
30
˚C/W
100
165
125
˚C/W
8.26 (.325)
7.62 (.300)
1.77 (.070)
1.14 (.045)
2.54 (.100) BSC
3.68 (.145)
2.92 (.115)
0.51 (.020)
0.33 (.013)
1.27 (.050) BSC
1.75 (.069) MAX
.356 (.014)
.203 (.008)
1.57 (.062)
1.37 (.054)
1.27 (.050)
0.40 (.016)
0.39 (.015)
MIN.
.558 (.022)
.356 (.014)
0.25 (.010)
0.19 (.008)
D
REF: JEDEC MS-001
0.25 (0.10)
0.10 (.004)
D
Some 8 and 16 lead
packages may have
1/2 lead at the end
of the package.
All specs are the same.
REF: JEDEC MS-012
Ordering Information
Part Number
CS3842BGN8
CS3842BGD8
CS3842BGDR8
CS3842BGD14
CS3842BGDR14
CS3843BGN8
CS3843BGD8
CS3843BGDR8
CS3843BGD14
CS3843BGDR14
Rev. 6/23/99
Description
8L PDIP
8L SO Narrow
8L SO Narrow (tape & reel)
14L SO Narrow
14L SO Narrow (tape & reel)
8L PDIP
8L SO Narrow
8L SO Narrow (tape & reel)
14L SO Narrow
14L SO Narrow (tape & reel)
Cherry Semiconductor Corporation reserves the right to
make changes to the specifications without notice. Please
contact Cherry Semiconductor Corporation for the latest
available information.
6
© 1999 Cherry Semiconductor Corporation
Similar pages