APLUS AVxx16 Series 巨華積体電路股份有限公司 GENERAL DESCRIPTION: The AVH316B, AVH316C, AVH316D, AV0716C, AV0716D, AV1416D, AV2116A, AV2816A is a single-chip synthesizing CMOS VLSI that can synthesize voice up to 3.5,7,14,21,28 seconds using APLUS qualified coding algorithm (LOGPCM). Customer speech data will be edited and programmed into ROM by changing one mask during one mask during the device fabrication. FEATURES: 1. Single power supply can operate from 2.4v through 5v. 2. The total voice duration is about 3.5,7,14,21,28,42 seconds could be partitioned up to 16 voice sections. Each voice section could have 4 playing lengths; the longest one is the origional voice+mute length. 3. Voice + mute length could up to 22 seconds ( 11 seconds in AVH316 ) (6k sampling rate) for each voice section. 4. One 112 voice-steps table, could be partitioned up to 16 subtables of steps. 5. 5 mask option of playback speed : 1> 4.3K ; 2> 5.0K ; 3> 6.0K ; 4> 7.5K ; 5> 10.0K ( Hz ) 6. 1 trigger input (TG): with resistive schmitt input (270K---1M) for CDS interface. sequential function : once the input was triggered sequentially the device will response by one subtable of voice_step sequentially and cyclically , from subtable_m ( m= 1 -16 ) to user defined subtable_n ( n= 1 - 16 ) . random function : Once the input was trigger , the device will response from subtable_m ( m: 1 - 16 ) to subtable_n ( n: 1 - 16 ) at random . snooze function : use 2 subtables : 1st stores ringing voice , playing when time's up. 2nd stores ( greeting sound + ) snooze time . 7.Has two debounce time : 10 ms, 50 us. with following mask option A>50us B>10ms C>IO1(VDD-50us,GND-10ms) D>IO2(VDD-50us,GND-10ms) E>IO3(VDD-50us,GND-10ms) C,D,E;could only be selected when IO1,IO2,IO3 are mask_option as control input . 8. Automatic Rosc selection : enable - the device will use external Rosc if it has external Rosc ; the device will use internal Rosc automatically if it hasn't external Rosc . ( It must be determined before operation ) disable - use external Rosc only . IO2 - VDD : disable GND : enable Internal Rosc options : (mask option) For VH316B ,AVH316C ,AVH316D ,AV0716C ,AV0716D ,AV1416D ,AV2116A , AV2816A : playback speed(khz) A B C D E F G H I J K L M 4.3 5 6 7.5 10 8.9 10.3 12.4 15.5 20.7 8.6 10 12 15 20 7.9 9.2 11 13.8 18.3 7 8.2 9.8 12.3 16.3 6.3 7.3 8.8 11 14.7 5.8 6.8 8.1 10.1 13.5 5.4 6.3 7.5 9.4 12.5 5.1 5.9 7.1 8.9 11.8 4.7 5.5 6.6 8.3 11 4.3 5 6 7.5 10 4.1 4.8 5.7 7.1 9.5 3.9 4.6 5.5 6.9 9.2 3.6 4.2 5 6.3 8.3 www.aplusinc.com.tw Page 1 / 9 2002-Rev.2 APLUS AVxx16 Serie 巨華積体電路股份有限公司 9. Playing mode :EDGEL/LEVEL , HOLD/UNHOLD , RETRIGGER/IRRETRIGGER with following mask options : EDGE/LEVEL HOLD/UNHOLD RETRIGGERING/IRRETRIGGER A>EDGE A>HOLD A>IRRETRIGGER B>LEVEL B>UNHOLD B>RETRIGGER C>IO1(VDD-edge.GND-level) C>IO1(VDD-hold,GND-unhold) C>IO1(VDD-irretrigger,GND-retrigger) D>IO2(VDD-edge.GND-level) D>IO2(VDD-hold,GND-unhold) D>IO2(VDD-irretrigger,GND-retrigger) E>IO3(VDD-edge.GND-level) E>IO3(VDD-hold,GND-unhold) E>IO3(VDD-irretrigger,GND-retrigger) C, D, E could only be selected when IO1,IO2,IO3 are mask_option as control input . 10. 3 I/O PINS WITH FOLLOWING OPTIONS: * IO1 * IO2 A>COUT B>STOPH C>STOPL A>PWM1 B>STOPH D>BUSYH D>BUSYH G>DYNA1/4 E>BUSYL F>6HZ H>DYN2/4 I>DYN3/4 J>USED AS CONTROL INPUT G>DYNA1/4 * IO3 C>STOPL E>BUSYL F>6HZ H>DYN2/4 I>DYN3/4 J>USED AS CONTROL INPUT A>PWM2 B>STOPH C>STOPL D>BUSYH E>BUSYL F>6HZ G>DYNA1/4 H>DYN2/4 I>DYN3/4 J>USED AS CONTROL INPUT Item_F : 0.75Hz or 1.5Hz or 3Hz or 6Hz(mask option) Item_B~I : with one subtable enable status option for IO1, IO2, IO3. COUT : 3 current output levels, with 4 mask options (1.5mA;3mA;4.5mA;IO3<GND-3mA,VDD-4.5mA>). PWM1, PWM2 : must be selected on the same time ,direct driving buzzer or 8 or 32 or 64 ohm speaker. STOPH, STOPL : 40 ms high/low output when device stop playing.(drive 1.8 mA,sink 10mA;3v). BUSYH, BUSYL : high/low output during device playing (drive 1.8 mA,sink 10mA;3v). 6Hz/3Hz, DYNA1/4, 2/4, 3/4 : LED driving. (drive 1.8 mA, sink 10mA;3v) Used as control input : internal pull GND (0.5uA,3V) For all the IO options : the dynamic should choice same level. If IO2 and IO3 are both at 6Hz(3Hz), they will flash alternatively. When used as control input, they could be used to control following options by bonding or toggle switch. EDGE/LEVEL, HOLD/UNHOLD, RETRIGGER/IRRETRIGGER, DEBOUNCE 10ms/50us ㆒般規格: AVH316B ,AVH316C ,AVH316D ,AV0716C ,AV0716D ,AV1416D ,AV2116A,AV2816A 乃㆒單晶片CMOS VLSI語音合成器，它以LOGPCM編碼方式，合成長達3.5、7、14、21、28、42 秒之語音。藉由製造過程㆗更換 光罩，將客戶需要之語音資料編寫入ROM㆗。 特性： 1. 單㆒工作電壓範圍為2.4 - 5 伏特。 2. 語音總長度可達3.5、7、14、21、28、42秒，且可被分割成16語音段(section)，每段長度可不 同。 每㆒語音段有㆕種不同播放時間的選擇，但是任何㆒種播放時間皆不可長於原段的 (語 音+靜音)時間。 www.aplusinc.com.tw Page 2 / 9 2002-Rev.2 APLUS AVxx16 Serie 巨華積体電路股份有限公司 3. 其㆗每㆒語音段的長度 (語音+靜音時間) 最多可達22秒( 11秒in AVH316 )。 (在6kHz取樣頻 率㆘) 4. 具有112個語音格(VOICE - STEPS)，可規劃成16語音組(subtable)。 5. 5種播放速度:：1>4.3k ; 2>5k ; 3>6k ; 4>7.5k ; 5>10k Hz 6. 單鍵觸發(TG)：內含電阻式史密特輸入(270K-1M)提供光敏電阻(CDS)使用。 順序觸發 (SEQUENTIAL)：㆒經觸發將由語音組(subtable) 1 至設定之語音組 (subtable n ; n=1 - 16 )每次觸發播放㆒組按順序循環播放。 隨機觸發(RANDOM)：㆒經觸發將由設定第m語音組 (m由光罩選擇)至第n語音組(n由 光罩選擇) 每次觸發播放㆒語音組, 按不規則播放。 貪睡功能 (SNOOZE)：使用㆓個語音,語音組1 儲存時間到達時的鬧鈴聲音 ，語音組2 儲存聲音和貪睡時間 7. 防止誤動作(DEBOUNCE)時間：10ms-提供㆒般手動操作, 50us-提供跳動開關使用, 以㆘選擇。 A>50us , B>10ms , C>IO1(VDD-50us,GND-10ms) , D>IO2(VDD-50us,GND-10ms) , E>IO3(VDD-50us,GND-10ms) , 選擇C,D,E 時,IO1,IO2,IO3須選擇為控制輸入 8. 自動選擇振盪電阻(光罩選擇): A). 致能 - 如果有接外部振盪電阻,則優先使用外部振盪電阻;如果沒有,則使用內部已選擇 之振盪電阻(振盪電阻的狀態須在觸發前決定）。 B). 非致能 - 只能使用外部振盪電阻。 C). IO2控制輸入：VDD - 非致能；GND - 致能。 D). 內部振盪電阻選擇 (光罩選擇)： For AVH316B ,AVH316C ,AVH316D ,AV0716C ,AV0716D ,AV1416D ,AV2116A ,AV2816A : 電 阻 選 選 擇 振 盪 播 器 放 速 項 度 選 4.3 5 6 7.5 10 A B C D E F G H I J K L M 8.9 10.3 12.4 15.5 20.7 8.6 10 12 15 20 7.9 9.2 11 13.8 18.3 7 8.2 9.8 12.3 16.3 6.3 7.3 8.8 11 14.7 5.8 6.8 8.1 10.1 13.5 5.4 6.3 7.5 9.4 12.5 5.1 5.9 7.1 8.9 11.8 4.7 5.5 6.6 8.3 11 4.3 5 6 7.5 10 4.1 4.8 5.7 7.1 9.5 3.9 4.6 5.5 6.9 9.2 3.6 4.2 5 6.3 8.3 9. 觸發模式的光罩選擇： 邊緣觸發 / 位準觸發 (EDGE / LEVEL) □ 邊緣觸發 □ 位準觸發 □ I01 (VDD-邊緣觸發 ，GND-位準觸發) □ I02 (VDD-邊緣觸發 ，GND-位準觸發) □ I03 (VDD-邊緣觸發 ，GND-位準觸發) 保持 / 非保持 ( HOLD / UNHOLD) □ 保持 □ 非保持 □ I01 (VDD-保持，GND-非保持) □ I02 (VDD-保持，GND-非保持) □ I03 (VDD-保持，GND-非保持) 後段蓋前段 / 無後段蓋 前段 (RETRIGGER / IRRETRIGGER) □ 後段蓋前段 □ 無後段蓋前段 □ I01(VDD-後段蓋前段,GND無後段蓋前段) □ I02(VDD-後段蓋前段,GND無後段蓋前段) □ I03(VDD-後段蓋前段,GND無後段蓋前段) ※ 選擇C,D,E 時,IO1,IO2,IO3須選擇為控制輸入。 www.aplusinc.com.tw Page 3 / 9 2002-Rev.2 APLUS 巨華積体電路股份有限公司 AVxx16 Serie 10.㆔個I/O PINS 有以㆘選擇： □ IO1的選擇 A) COUT聲音輸出 B) 停止播放時送出高位準脈衝. C) 停止播放時送出低位準脈衝. D) 播放時送出高位準訊號. E) 播放時送出低位準訊號. F) LED 6HZ閃爍. G) LED動態 1/4位準訊號. H) LED動態 2/4位準訊號. I) LED動態 3/4位準訊號. J) 控制輸入 □ IO2的選擇 A) PWM1聲音輸出 B)停止播放時送出高位準脈衝. C) 停止播放時送出低位準脈衝. D) 播放時送出高位準訊號. E) 播放時送出低位準訊號. F) LED 6HZ閃爍. G) LED動態 1/4位準訊號. H) LED動態 2/4位準訊號. I) LED動態 3/4位準訊號. J) 控制輸入 □ IO3的選擇 A) .PWM2聲音輸出 B)停止播放時送出高位準脈衝. C) 停止播放時送出低位準脈衝. D) 播放時送出高位準訊號. E) 播放時送出低位準訊號. F) LED 6HZ閃爍. G) LED動態 1/4位準訊號. H) LED動態 2/4位準訊號. I) LED動態 3/4位準訊號. J) 控制輸入 第 F 項: 可選擇為LED 0.75Hz閃爍或為LED 1.5Hz閃爍或為LED 3Hz閃爍 或為LED 6Hz閃爍。 第 B – I 項:㆒組狀態致能選擇, 可由光罩選擇IO1, IO2及IO3對每㆒語音組(subtable)致能或非 致能。 COUT：3種電流輸出, 4種光罩選擇 (1.5mA，3.0mA，4.5mA， IO3<GND-3mA,VDD-4.5mA> ) PWM1、PWM2須同時選擇，可驅動 buzzer 或 8、32、64 ohm speaker。 IO1、IO2及IO3為控制輸入時，有㆒內部到㆞路徑(0.5uA，3v)。 若IO1 - IO3同時選擇 LED動態位準訊號.，須選擇同㆒位準。 如IO2和IO3選擇相同LED 6HZ(3HZ)之狀態輸出時它們將交互閃爍。 IO1、IO2及IO3為控制輸入時，可控制以㆘功能： EDGE/LEVEL, HOLD/UNHOLD, RETRIGGER/IRRETRIGGER, DEBOUNCE 10ms/50us BLOCK DIAGRAM: www.aplusinc.com.tw Page 4 / 9 2002-Rev.2 APLUS AVxx16 Serie 巨華積体電路股份有限公司 PIN DESCRIPTION : PAD NAME VDD OSC TEST TG IO1,IO2,IO3 VSS PIN ATTR. POWER I I I I/O POWER FUNCTION POSITIVE POWER SUPPLY. OSCILLATOR INPUT (300K ohm CONNECT TO VDD). TEST PAD,FOR PRODUCTION TESTING (TEST HIGH FOR TESTING) TRIGGER INPUT, INTERNAL PULL LOW (HIGH ACTIVE). AUDIO SIGNAL; STATUS OUTPUT; CONTROL INPUT. NEGATIVE POWER SUPPLY. ABSOLUTE MAXIMUM RATING : SYMBOL VDD~VSS VIN (FOR ALL INPUT) VOUT (FOR ALL OUTPUT) T (OPERATING) T (STORAGE) RATING -0.5~+7.0 VSS-0.3<VIN<VDD+0.3 GND<VOUT<VDD 0~+70 -25~+75 UNIT V V V ℃ ℃ DC CHARACTERISTICS : SYMBOL VDD Isb Iop Iih Iil Ico Iih Iil Ioh Iol dF/F dF/F PARAMETER OPERATING VOLTAGE SUPPLY STANDBY CURRENT OPERATING TG MIN. 2.4 IO1 USE AS CURRENT OUT (FULL SCALE) IO1,IO2,IO3 USE AS CONTROL INPUT IO1,IO2,IO3 USE AS STATUS OUTPUT DURING OPERATING FREQUENCY STABILITY Fosc VARIATION -1.2 -2.4 -3.6 www.aplusinc.com.tw TYP. 3 5 0 -1.5 -3 -4.5 MAX. 5 0.1 200 -1.8 -3.6 -5.4 0.5 UNIT V uA CONDITION uA VDD=3V ,I/O OPEN (WITH Rosc) VDD=3V mA VDD=3V, V O/P=0.7V uA VDD=3V mA VDD=3V, V O/P=0V 0 8 -10 min:-0.9 max:-1.4 10 -10 Page 5 / 9 12 10 % 10 % VDD=3V, V O/P=3V Fosc(3v)-Fosc(2.4v) Fosc (3v) VDD=3V,Rosc=300K (Rosc=180K in AV1416 ) 2002-Rev.2 APLUS 巨華積体電路股份有限公司 www.aplusinc.com.tw Page 6 / 9 AVxx16 Serie 2002-Rev.2 APLUS AVxx16 Serie 巨華積体電路股份有限公司 APPLICATION CIRCUIT: A> IO1 -- COUT ; IO2 -- LED ; IO3 -- CONTROL INPUT. Rosc busy,3Hz,6Hz,or dynamic VDD IO2 TG LED IO3 GND S ( 8 ohm SPEAKER ) T ( 8050 ) IO1 B> IO1 -- LED ; IO2,IO3 --8,32,64 ohm SPEAKER OR BUZZER. Rosc VDD TG busy,3Hz,6Hz,or dynamic IO1 LED IO2 GND IO3 S (BUZZER OR 8,32,64 ohm SPEAKER ) C> IO1 -- COUT ; IO2,IO3 -- 8,32,64 ohm SPEAKER OR BUZZER. Rosc S ( 8 ohm SPEAKER ) VDD IO1 TG T ( 8050 ) IO2 GND IO3 S (BUZZER OR 8,32,64 ohm SPEAKER ) NOTE: 1>Rosc=300K ohm ( Rosc=180K ohm in AMA140A ) ( typical ) , or use internal Rosc ( it must be determined before operation ) Tbata=130( typical ) 2>BUZZER:resonant frequency should around 1KHz. 3>Input switch could be replace by CDS. 4>COUT,PWM1,PWM2 are tristate during standby. www.aplusinc.com.tw Page 7 / 9 2002-Rev.2 APLUS 巨華積体電路股份有限公司 AVxx16 Serie APPLICATION CIRCUITS : D > SNOOZE FUNCTION timer switch S ( 8 ohm SPEAKER ) Rosc OSC ( normal on switch ) VDD IO1 TG IO2 GND www.aplusinc.com.tw T ( 8050 ) Page 8 / 9 IO3 ( BUZZER or 8 , 32 , 64 ohm SPEAKER ) 2002-Rev.2 APLUS AVxx16 Serie 巨華積体電路股份有限公司 DIE SIZE: PRODUCT AVH316B AVH316C AVH316D AV0716C AV0716D AV1416D AV2116A AV2816A PIN NO. NAME 1 2 3 4 5 6 7 8 9 10 VDD1 OSC TEST TG IO1 VDD IO2 GND GND1 IO3 PIN NO. NAME 1 2 3 4 5 6 7 8 9 10 VDD1 OSC TEST TG IO1 VDD IO2 GND GND1 IO3 X 1450 Y 1080 PAD Size ( um^2 ) 80 * 80 Substrate GND UNIT um 1470 1100 80 * 80 GND um 1450 1470 1470 1470 1470 1230 1250 1610 1970 2370 80 * 80 80 * 80 80 * 80 80 * 80 80 * 80 GND GND GND GND GND um um um um um AVH316B AVH316C AVH316D X Y -606.1 -606.1 -485.2 -364.3 -243.4 -116.8 43.8 274 354.6 574.9 -197.4 -378.9 -378.9 -378.9 -378.9 -378.9 -354.3 -374.2 -374.2 -354.3 AV0716C AV0716D AV1416D AV2116A X Y X Y X Y -606.1 -606.1 -485.2 -364.3 -243.4 -116.8 43.8 274 354.6 574.9 -278 459.5 459.5 459.5 459.5 459.5 434.8 454.8 454.8 434.8 -606.1 -606.1 -485.2 -364.3 -243.4 -116.8 43.8 274 354.6 574.9 -455.2 -636.7 -636.7 -636.7 -636.7 -636.7 -612.1 -631.9 -631.9 -612.1 -606.1 -606.1 -485.2 -364.3 -243.4 -116.8 43.8 274 354.6 574.9 -637.5 -819.1 -819.1 -819.1 -819.1 -819.1 -794.4 -814.3 -814.3 -794.4 AV2816A X Y -606.1 -823.9 -606.1 -1005.5 -485.2 -1005.5 -364.3 -1005.5 -243.4 -1005.5 -116.8 -1005.5 43.8 -975.4 274 -995.3 354.6 -995.3 574.9 -975.4 NOTE : ( 1 ) . All data and specifications are subject to change without notice . ( 2 ) . Both VDD and VDD1 be connected to positive power supply ; GND and GND1 be connected to negative power supply for avoid power supply noise during operation . ( 3 ) . 0.1 uf capacitor be connected between positive and negative power supply were subjected for operating stability . www.aplusinc.com.tw Page 9 / 9 2002-Rev.2