Aluminum electrolytic capacitors Single-ended capacitors Series/Type: B41858 Date: December 2006 EPCOS AG 2007. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Single-ended capacitors B41858 Low impedance 105 °C Long-life grade capacitors for professional applications Applications For use in output circuits of switch-mode power supplies of compact design For professional industrial electronics, telecommunications and data processing equipment Automotive electronics Features Low impedance at high frequency Low ESR High ripple current capability High reliability and long useful life Wide temperature range Construction Radial leads Charge-discharge proof, polar Aluminum case with insulating sleeve Minus pole marking on the insulating sleeve Case with safety vent Delivery mode Terminal configurations and packing: Bulk Taped, Ammo pack Cut Kinked PAPR (protection against polarity reversal): crimped leads, J leads, bent leads Refer to chapter "Single-ended capacitors Taping, packing and lead configurations" for further details and ordering example. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 30 B41858 Low impedance 105 °C Specifications and characteristics in brief Rated voltage VR Surge voltage VS 10 ... 100 V DC 1.15 VR Rated capacitance CR Capacitance tolerance 22 ... 12000 µF ±20% M Dissipation factor tan δ (20 °C, 120 Hz) For capacitance higher than 1000 µF add 0.02 for every increase of 1000 µF. VR (V DC) 10 16 25 35 50 63 80 100 tan δ (max.) 0.19 Diameter (mm) 8 ... 12.5 16 18 ESL (nH) 20 26 34 0.16 0.14 0.12 0.10 0.10 0.10 0.08 Leakage current Ileak (20 °C, 5 min) Self-inductance ESL Useful life 105 °C, VR, IAC,R 105 °C, VR, IAC,R Requirements Voltage endurance test 105 °C, VR > 3000 h for d = 8 mm > 5000 h for d ≥ 10 mm ∆C/C tan δ Ileak ≤ ±40% of initial value ≤ 3 times initial specified limit ≤ initial specified limit 3000 h for d = 8 mm 5000 h for d ≥ 10 mm ∆C/C ≤ ±30% of initial value tan δ ≤ 2 times initial specified limit Ileak ≤ initial specified limit Vibration resistance test To IEC 60068-2-6, test Fc: Displacement amplitude 0.75 mm, frequency range 10 ... 2000 Hz, acceleration max. 20 g, duration 3 × 2 h. Capacitor rigidly clamped by the aluminum case. Post test requirements IEC climatic category To IEC 60068-1: 55/105/56 (55 °C/+105 °C/56 days damp heat test) Sectional specification IEC 60384-4 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 30 B41858 Low impedance 105 °C Dimensional drawings With stand-off rubber seal Diameters (mm): 8, 10, 12.5, 16, 18 With flat rubber seal Diameter (mm): 8 Dimensions and weights Dimensions (mm) d +0.5 8 10 10 10 12.5 12.5 12.5 12.5 16 16 16 18 18 18 18 18 l 11.5 +1.5 12.5 +1.0 16 +1.0 20 +2.0 20 +2.0 25 +2.0 30 +2.0 40 +2.0 20 +2.0 25 +2.0 31.5 +2.0 20 +2.0 25 +2.0 31.5 +2.0 35 +2.0 40 +2.0 Please read Cautions and warnings and Important notes at the end of this document. a ±0.5 3.5 5.0 5.0 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 Page 4 of 30 b 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.80 ±0.05 0.80 ±0.05 0.80 ±0.05 0.80 ±0.05 0.80 ±0.05 0.80 ±0.1 0.80 ±0.1 0.80 ±0.1 0.80 ±0.1 0.80 ±0.1 Approx. weight g 1.0 1.6 1.9 2.6 3.6 4.5 5.3 7.4 5.5 7.5 7.8 8.0 9.0 11.0 13.0 16.0 B41858 Low impedance 105 °C Overview of available types VR (V DC) 10 16 25 35 Case dimensions d × l (mm) CR (µF) 8 × 11.5 8 × 11.5 10 × 12.5 8 × 11.5 10 × 12.5 120 180 220 270 330 8 × 11.5 390 8 × 11.5 470 8 × 11.5 560 10 × 12.5 680 10 × 12.5 820 10 × 16 1000 10 × 16 8 × 11.5 8 × 11.5 10 × 12.5 10 × 16 10 × 12.5 10 × 16 10 × 20 10 × 20 10 × 16 12.5 × 20 10 × 20 1200 10 × 20 1500 12.5 × 20 12.5 × 25 10 × 20 12.5 × 20 12.5 × 25 16 × 20 12.5 × 40 16 × 25 1800 10 × 20 12.5 × 25 16 × 20 16 18 × 31.5 × 20 2200 12.5 × 20 12.5 × 25 12.5 × 40 16 × 25 18 × 25 2700 12.5 × 25 16 × 20 16 18 × 31.5 × 20 18 × 31.5 3300 12.5 × 25 16 × 20 12.5 × 40 16 × 25 18 × 25 18 × 35 3900 12.5 × 40 16 × 20 16 18 × 31.5 × 20 18 × 31.5 4700 18 × 20 18 × 25 18 × 35 18 × 40 5600 12.5 × 40 18 × 40 6800 16 × 31.5 18 × 31.5 8200 18 × 31.5 18 × 35 10000 18 × 35 18 × 40 12000 18 × 40 Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 30 B41858 Low impedance 105 °C VR (V DC) 50 63 80 100 Case dimensions d × l (mm) CR (µF) 22 8 × 11.5 27 10 × 12.5 10 × 16 10 × 20 33 8 × 11.5 39 10 × 12.5 56 8 × 11.5 100 8 × 11.5 120 10 × 12.5 82 8 × 11.5 10 × 16 10 × 12.5 10 × 20 10 × 16 12.5 × 20 12.5 × 25 12.5 × 20 150 180 10 × 16 × 20 12.5 × 25 12.5 × 20 12.5 × 30 16 × 20 12.5 × 20 16 × 25 16 18 × 31.5 × 25 12.5 × 25 12.5 × 40 18 × 20 18 × 31.5 18 × 35 18 × 40 10 220 16 270 330 10 × 20 390 470 12.5 × 20 560 12.5 × 25 680 820 1000 12.5 × 30 16 × 20 × 20 16 18 × 31.5 × 25 12.5 × 30 12.5 × 40 16 × 25 18 × 20 18 × 31.5 12.5 × 40 16 × 20 16 18 18 × 35 18 × 40 16 18 16 × 31.5 × 25 × 31.5 × 20 1200 18 × 31.5 1500 18 × 25 18 × 35 1800 18 × 31.5 18 × 40 2200 18 × 35 2700 18 × 40 Other voltage and capacitance ratings are available upon request. Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 30 × 25 12.5 × 40 18 × 20 B41858 Low impedance 105 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm VR = 10 V DC 330 8 × 11.5 390 8 × 11.5 470 8 × 11.5 560 10 × 12.5 680 10 × 12.5 820 10 × 16 1000 10 × 16 1800 10 × 20 2200 12.5 × 20 2700 12.5 × 25 3300 12.5 × 25 3300 16 × 20 3900 12.5 × 40 3900 16 × 20 4700 18 × 20 5600 12.5 × 40 6800 16 × 31.5 8200 18 × 31.5 10000 18 × 35 12000 18 × 40 VR = 16 V DC 270 8 × 11.5 330 8 × 11.5 470 10 × 12.5 680 10 × 16 1000 10 × 20 1200 10 × 20 1500 12.5 × 20 ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 105 °C mA IAC,max Ordering code 100 kHz (composition see 85 °C below) mA 2.195 2.195 2.195 1.035 1.035 0.946 0.946 0.584 0.496 0.327 0.327 0.307 0.243 0.307 0.271 0.243 0.192 0.165 0.160 0.125 0.727 0.615 0.511 0.429 0.353 0.293 0.240 0.133 0.121 0.098 0.088 0.088 0.074 0.074 0.067 0.061 0.054 0.051 0.047 0.043 0.274 0.274 0.274 0.129 0.129 0.118 0.118 0.073 0.062 0.041 0.041 0.038 0.030 0.038 0.034 0.030 0.024 0.021 0.020 0.016 0.246 0.246 0.246 0.113 0.113 0.105 0.105 0.062 0.060 0.034 0.034 0.033 0.025 0.033 0.031 0.025 0.022 0.020 0.018 0.015 436 436 436 746 746 846 846 1202 1396 2028 2028 2146 2858 2146 2381 2858 3122 3539 3864 4467 654 654 654 1118 1118 1269 1269 1803 2094 3043 3043 3219 4286 3219 3571 4286 4683 5308 5796 6700 B41858C3337M*** B41858C3397M*** B41858C3477M*** B41858C3567M*** B41858C3687M*** B41858C3827M*** B41858C3108M*** B41858C3188M*** B41858C3228M*** B41858C3278M*** B41858C3338M*** B41858D3338M*** B41858C3398M*** B41858D3398M*** B41858C3478M*** B41858C3568M*** B41858C3688M*** B41858C3828M*** B41858C3109M*** B41858C3129M*** 1.200 1.200 1.035 0.946 0.584 0.584 0.496 0.749 0.612 0.430 0.297 0.202 0.168 0.135 0.150 0.150 0.129 0.118 0.073 0.073 0.062 0.134 0.134 0.113 0.105 0.062 0.062 0.060 590 590 746 846 1202 1202 1396 885 885 1118 1269 1803 1803 2094 B41858C4277M*** B41858C4337M*** B41858C4477M*** B41858C4687M*** B41858C4108M*** B41858C4128M*** B41858C4158M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 30 B41858 Low impedance 105 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm VR = 16 V DC 1800 12.5 × 25 2200 12.5 × 25 2700 16 × 20 3300 12.5 × 40 3300 16 × 25 3900 16 × 31.5 3900 18 × 20 4700 18 × 25 6800 18 × 31.5 8200 18 × 35 10000 18 × 40 VR = 25 V DC 180 8 × 11.5 220 8 × 11.5 330 10 × 12.5 470 10 × 16 820 10 × 20 1000 12.5 × 20 1500 12.5 × 25 1800 16 × 20 2200 12.5 × 40 2200 16 × 25 2700 16 × 31.5 2700 18 × 20 3300 18 × 25 3900 18 × 31.5 4700 18 × 35 5600 18 × 40 ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 105 °C mA IAC,max Ordering code 100 kHz (composition see 85 °C below) mA 0.327 0.327 0.307 0.243 0.251 0.192 0.271 0.217 0.165 0.160 0.125 0.112 0.103 0.084 0.077 0.077 0.065 0.065 0.059 0.048 0.046 0.043 0.041 0.041 0.038 0.030 0.031 0.024 0.034 0.027 0.021 0.020 0.016 0.034 0.034 0.033 0.025 0.029 0.022 0.031 0.024 0.020 0.018 0.015 2028 2028 2146 2858 2483 3122 2381 2941 3539 3864 4467 3043 3043 3219 4286 3724 4683 3571 4412 5308 5796 6700 B41858C4188M*** B41858C4228M*** B41858C4278M*** B41858D4338M*** B41858C4338M*** B41858D4398M*** B41858C4398M*** B41858C4478M*** B41858C4688M*** B41858C4828M*** B41858C4109M*** 1.200 1.200 1.035 0.946 0.584 0.496 0.327 0.307 0.243 0.251 0.192 0.271 0.217 0.165 0.160 0.125 0.982 0.804 0.536 0.376 0.216 0.177 0.118 0.098 0.092 0.092 0.075 0.075 0.069 0.058 0.054 0.050 0.150 0.150 0.129 0.118 0.073 0.062 0.041 0.038 0.030 0.031 0.024 0.034 0.027 0.021 0.020 0.016 0.134 0.134 0.113 0.105 0.062 0.060 0.034 0.033 0.025 0.029 0.022 0.031 0.024 0.020 0.018 0.015 590 590 746 846 1202 1396 2028 2146 2858 2483 3122 2381 2941 3539 3864 4467 885 885 1118 1269 1803 2094 3043 3219 4286 3724 4683 3571 4412 5308 5796 6700 B41858C5187M*** B41858C5227M*** B41858C5337M*** B41858C5477M*** B41858C5827M*** B41858C5108M*** B41858C5158M*** B41858C5188M*** B41858D5228M*** B41858C5228M*** B41858D5278M*** B41858C5278M*** B41858C5338M*** B41858C5398M*** B41858C5478M*** B41858C5568M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 30 B41858 Low impedance 105 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm VR = 35 V DC 120 8 × 11.5 180 10 × 12.5 220 10 × 12.5 330 10 × 16 470 10 × 20 560 10 × 20 680 12.5 × 20 1000 12.5 × 25 1200 16 × 20 1500 12.5 × 40 1500 16 × 25 1800 16 × 31.5 1800 18 × 20 2200 18 × 25 2700 18 × 31.5 3300 18 × 35 4700 18 × 40 VR = 50 V DC 82 8 × 11.5 100 8 × 11.5 120 10 × 12.5 180 10 × 16 330 10 × 20 470 12.5 × 20 560 12.5 × 25 680 12.5 × 30 820 12.5 × 40 ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 105 °C mA IAC,max Ordering code 100 kHz (composition see 85 °C below) mA 1.200 1.035 1.035 0.946 0.584 0.584 0.496 0.327 0.307 0.243 0.251 0.192 0.271 0.217 0.165 0.160 0.125 1.263 0.842 0.689 0.459 0.323 0.271 0.223 0.152 0.126 0.101 0.101 0.084 0.084 0.080 0.065 0.061 0.048 0.150 0.129 0.129 0.118 0.073 0.073 0.062 0.041 0.038 0.030 0.031 0.024 0.034 0.027 0.021 0.020 0.016 0.134 0.113 0.113 0.105 0.062 0.062 0.060 0.034 0.033 0.025 0.029 0.022 0.031 0.024 0.020 0.018 0.015 590 746 746 846 1202 1202 1396 2028 2146 2858 2483 3122 2381 2941 3539 3864 4467 885 1118 1118 1269 1803 1803 2094 3043 3219 4286 3724 4683 3571 4412 5308 5796 6700 B41858C7127M*** B41858C7187M*** B41858C7227M*** B41858C7337M*** B41858C7477M*** B41858C7567M*** B41858C7687M*** B41858C7108M*** B41858C7128M*** B41858D7158M*** B41858C7158M*** B41858D7188M*** B41858C7188M*** B41858C7228M*** B41858C7278M*** B41858C7338M*** B41858C7478M*** 5.168 5.168 2.984 1.400 1.000 0.880 0.712 0.360 0.269 1.540 1.263 1.053 0.702 0.383 0.269 0.226 0.186 0.154 0.646 0.646 0.373 0.175 0.125 0.110 0.089 0.045 0.034 0.573 0.573 0.336 0.160 0.118 0.104 0.082 0.043 0.032 340 340 555 778 1030 1300 1490 2140 2799 510 510 833 1167 1545 1950 2235 3210 4199 B41858C6826M*** B41858C6107M*** B41858C6127M*** B41858C6187M*** B41858C6337M*** B41858C6477M*** B41858C6567M*** B41858C6687M*** B41858C6827M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 30 B41858 Low impedance 105 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm VR = 50 V DC 820 16 × 20 1000 16 × 31.5 1000 18 × 20 1500 18 × 25 1800 18 × 31.5 2200 18 × 35 2700 18 × 40 VR = 63 V DC 56 8 × 11.5 82 10 × 12.5 120 10 × 16 180 10 × 20 270 12.5 × 20 330 12.5 × 20 390 12.5 × 25 470 16 × 20 680 12.5 × 40 680 16 × 25 680 18 × 20 820 16 × 31.5 820 18 × 25 1200 18 × 31.5 1500 18 × 35 1800 18 × 40 ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 105 °C mA IAC,max Ordering code 100 kHz (composition see 85 °C below) mA 0.401 0.260 0.477 0.382 0.300 0.268 0.210 0.154 0.126 0.126 0.084 0.070 0.069 0.065 0.050 0.032 0.048 0.038 0.030 0.027 0.021 0.046 0.030 0.044 0.036 0.028 0.024 0.020 1820 2653 1997 2417 2989 3320 3871 2730 3980 2995 3626 4483 4980 5807 B41858D6827M*** B41858C6108M*** B41858D6108M*** B41858C6158M*** B41858C6188M*** B41858C6228M*** B41858C6278M*** 5.413 5.766 3.075 1.986 1.688 1.688 1.236 1.037 0.717 0.772 0.960 0.541 0.761 0.518 0.441 0.375 2.256 1.540 1.053 0.702 0.468 0.383 0.324 0.269 0.186 0.186 0.186 0.154 0.154 0.105 0.084 0.070 0.541 0.577 0.308 0.199 0.169 0.169 0.124 0.104 0.072 0.077 0.096 0.054 0.076 0.052 0.044 0.038 0.488 0.500 0.279 0.180 0.153 0.153 0.112 0.094 0.065 0.070 0.087 0.049 0.069 0.047 0.040 0.034 310 354 519 705 876 876 1118 1272 1785 1600 1427 2092 1735 2294 2592 2967 464 531 779 1058 1315 1315 1676 1907 2677 2400 2140 3138 2602 3441 3888 4450 B41858C8566M*** B41858C8826M*** B41858C8127M*** B41858C8187M*** B41858C8277M*** B41858C8337M*** B41858C8397M*** B41858C8477M*** B41858C8687M*** B41858D8687M*** B41858E8687M*** B41858C8827M*** B41858D8827M*** B41858C8128M*** B41858C8158M*** B41858C8188M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 10 of 30 B41858 Low impedance 105 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω VR = 80 V DC 33 8 × 11.5 12.219 3.828 39 10 × 12.5 9.813 3.239 56 10 × 16 6.542 2.256 82 10 × 20 4.606 1.540 150 12.5 × 20 3.048 0.842 180 12.5 × 25 2.038 0.702 270 12.5 × 30 1.732 0.468 270 16 × 20 1.313 0.468 330 16 × 25 0.985 0.383 390 12.5 × 40 1.314 0.324 390 18 × 20 1.260 0.324 470 16 × 31.5 0.973 0.269 470 18 × 25 1.008 0.269 680 18 × 31.5 0.720 0.186 820 18 × 35 0.679 0.154 1000 18 × 40 0.438 0.126 VR = 100 V DC 22 8 × 11.5 12.219 4.593 27 10 × 12.5 9.813 3.743 33 10 × 16 6.542 3.062 56 10 × 20 4.606 1.804 100 12.5 × 20 3.048 1.011 120 12.5 × 25 2.038 0.842 180 12.5 × 30 1.732 0.561 180 16 × 20 1.313 0.561 220 16 × 25 0.985 0.459 270 12.5 × 40 1.314 0.374 ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 105 °C mA IAC,max Ordering code 100 kHz (composition see 85 °C below) mA 1.222 0.981 0.654 0.461 0.305 0.204 0.173 0.131 0.099 0.131 0.126 0.097 0.101 0.072 0.068 0.044 1.114 0.883 0.589 0.423 0.281 0.188 0.159 0.122 0.091 0.121 0.119 0.090 0.095 0.068 0.063 0.042 205 266 357 460 647 864 1009 1119 1402 1309 1220 1546 1477 1907 2061 2683 307 400 536 691 971 1296 1514 1678 2103 1963 1830 2319 2215 2861 3092 4025 B41858C0336M*** B41858C0396M*** B41858C0566M*** B41858C0826M*** B41858C0157M*** B41858C0187M*** B41858C0277M*** B41858D0277M*** B41858C0337M*** B41858C0397M*** B41858D0397M*** B41858C0477M*** B41858D0477M*** B41858C0687M*** B41858C0827M*** B41858C0108M*** 1.222 0.981 0.654 0.461 0.305 0.204 0.173 0.131 0.099 0.131 1.114 0.883 0.589 0.423 0.281 0.188 0.159 0.122 0.091 0.121 205 266 357 460 647 864 1009 1119 1402 1309 307 400 536 691 971 1296 1514 1678 2103 1963 B41858C9226M*** B41858C9276M*** B41858C9336M*** B41858C9566M*** B41858C9107M*** B41858C9127M*** B41858C9187M*** B41858D9187M*** B41858C9227M*** B41858C9277M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 30 B41858 Low impedance 105 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm ESRmax 10 kHz 40 °C Ω VR = 100 V DC 270 18 × 20 330 16 × 31.5 330 18 × 25 390 18 × 31.5 560 18 × 35 680 18 × 40 1.260 0.973 1.008 0.720 0.679 0.438 ESRmax 120 Hz 20 °C Ω ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 105 °C mA IAC,max Ordering code 100 kHz (composition see 85 °C below) mA 0.374 0.306 0.306 0.259 0.180 0.149 0.126 0.097 0.101 0.072 0.068 0.044 0.119 0.090 0.095 0.068 0.063 0.042 1220 1546 1477 1907 2061 2683 1830 2319 2215 2861 3092 4025 B41858D9277M*** B41858C9337M*** B41858D9337M*** B41858C9397M*** B41858C9567M*** B41858C9687M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 30 B41858 Low impedance 105 °C Useful life depending on ambient temperature TA under ripple current operating conditions1) d = 8 mm d ≥ 10 mm 1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life graphs. Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 30 B41858 Low impedance 105 °C Frequency factor of permissible ripple current IAC versus frequency f Please read Cautions and warnings and Important notes at the end of this document. Page 14 of 30 B41858 Low impedance 105 °C Taping, packing and lead configurations Taping Single-ended capacitors are available taped in Ammo pack from diameter 5 to 18 mm as follows: Lead spacing F = 2.5 mm (∅ d = 5 … 6.3 mm) Lead spacing F = 3.5 mm (∅ d = 8 mm) Lead spacing F = 5.0 mm (∅ d = 5 … 12.5 mm) Lead spacing F = 7.5 mm (∅ d = 16 ... 18 mm). Lead spacing 2.5 mm (∅ d = 5 ... 6.3 mm) Last 3 digits of ordering code: 007 Dimensions in mm ∅d 5 F H W W0 W1 W2 H0 P P0 P1 I1 t ∆h D0 2.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0 6.3 Toler- +0.8 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2 ance 02 Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 30 B41858 Low impedance 105 °C Lead spacing 3.5 mm (∅ d = 8 mm) Last 3 digits of ordering code: 006 Dimensions in mm ∅d 8 Tolerance F H W W0 W1 W2 P P0 P1 I1 t ∆h 3.5 18.5 18.0 12.5 9.0 1.5 12.7 12.7 4.6 1.0 0.7 1.0 +0.8 02 1.0 ±0.5 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 Please read Cautions and warnings and Important notes at the end of this document. Page 16 of 30 D0 4.0 max. ±0.2 B41858 Low impedance 105 °C Lead spacing 5.0 mm (∅ d = 5 ... 8 mm) Last 3 digits of ordering code: 008 Lead spacing 5.0 mm (∅ d = 10 ... 12.5 mm) Last 3 digits of ordering code: 008 Dimensions in mm ∅d 5 6.3 F H W W0 W1 W2 H0 P P0 P1 I1 t ∆h D0 5.0 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 3.85 1.0 0.7 1.0 4.0 16.0 12.7 12.7 3.85 18.0 12.5 9.0 1.5 12.7 12.7 3.85 1.0 0.7 1.0 4.0 15.0 15.0 5.0 ±1.0 ±0.2 ±0.5 8 10 20.0 5.0 12.5 Toler- +0.8 ance 02 19.0 19.0 ±0.75 ±0.5 min. ±0.5 max. ±0.5 Please read Cautions and warnings and Important notes at the end of this document. Page 17 of 30 max. ±0.2 max. ±0.2 B41858 Low impedance 105 °C Lead spacing 7.5 mm (∅ d = 16 ...18 mm) Last 3 digits of ordering code: 009 Dimensions in mm ∅d 16 F H W 7.5 18.5 18.0 18 *) Toler0.5 ±0.8 ±0.5 ance +0.75 W0 W1 W2 P P0 P1 I1 t ∆P ∆h D0 12.5 9.0 1.5 30.0 15.0 3.75 1.0 0.7 0 0 4.0 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 ±1.0 ±1.0 ±0.2 *) Available only for case dimensions 18 × 20, 18 × 25 and 18 × 31.5 mm Please read Cautions and warnings and Important notes at the end of this document. Page 18 of 30 B41858 Low impedance 105 °C Packing units and box dimensions Ammo pack Please read Cautions and warnings and Important notes at the end of this document. Case size d×l mm Dimensions (mm) Amax Bmax Cmax 5 × 11 345 55 240 2000 6.3 × 11 345 55 290 2000 8 × 11.5 345 55 240 1000 10 × 12.5 345 55 280 750 10 × 16 345 60 200 500 10 × 20 345 60 200 500 12.5 × 20 345 65 280 500 12.5 × 25 345 65 280 500 12.5 × 25 345 65 280 500 12.5 × 30 345 65 275 500 16 × 20 315 65 275 300 16 × 25 315 65 275 300 16 × 31.5 315 65 275 300 18 × 20 315 65 275 250 18 × 25 315 65 275 250 18 × 31.5 315 65 275 250 Page 19 of 30 Packing units pcs. B41858 Low impedance 105 °C Kinked or cut leads Single-ended capacitors are available with kinked or cut leads. Other lead configurations also available upon request. Kinked leads Last 3 digits of ordering code: 001 With stand-off rubber seal Case size d × l (mm) With flat rubber seal Please read Cautions and warnings and Important notes at the end of this document. Page 20 of 30 Dimensions (mm) a ±0.5 10 × 20 5.0 12.5 × 20 5.0 12.5 × 25 5.0 12.5 × 30 5.0 12.5 × 35 5.0 12.5 × 40 5.0 16 × 20 7.5 16 × 25 7.5 16 × 31.5 7.5 18 × 20 7.5 18 × 25 7.5 18 × 31.5 7.5 18 × 35 7.5 18 × 40 7.5 20 × 20 10.0 20 × 25 10.0 20 × 40 10.0 22 × 30 10.0 22 × 35 10.0 22 × 40 10.0 B41858 Low impedance 105 °C Cut leads Last 3 digits of ordering code: 002 With stand-off rubber seal Case size d × l (mm) With flat rubber seal Please read Cautions and warnings and Important notes at the end of this document. Page 21 of 30 Dimensions (mm) a ±0.5 10 × 12.5 5.0 10 × 16 5.0 10 × 20 5.0 12.5 × 20 5.0 12.5 × 25 5.0 12.5 × 30 5.0 12.5 × 35 5.0 12.5 × 40 5.0 16 × 20 7.5 16 × 25 7.5 16 × 31.5 7.5 18 × 20 7.5 18 × 25 7.5 18 × 31.5 7.5 18 × 35 7.5 18 × 40 7.5 20 × 20 10.0 20 × 25 10.0 20 × 40 10.0 B41858 Low impedance 105 °C PAPR leads (Protection Against Polarity Reversal) These lead configurations ensure correct placement of the capacitor on the PCB with regard to polarity. PAPR leads are available for diameters from 10 mm up to 20 mm. There are three configurations available: Crimped leads, J leads, bent 90° leads Crimped leads Last 3 digits of ordering code: 003 With stand-off rubber seal With flat rubber seal Suggestion for PCB hole diameter Case size d × l (mm) Dimensions (mm) B ±0.2 C ±0.5 D ±0.1 E ±0.1 16 × 20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05 16 × 25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05 16 × 31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05 18 × 20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 35 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 40 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 20 × 20 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1 20 × 25 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1 20 × 40 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1 Please read Cautions and warnings and Important notes at the end of this document. Page 22 of 30 a ±0.5 ∅b B41858 Low impedance 105 °C J leads Last 3 digits of ordering code: 004 Suggestion for PCB hole diameter Case size d × l (mm) Dimensions (mm) C ±0.5 E ±0.5 J ±0.2 10 × 12.5 3.2 0.7 1.2 5.0 0.6 ±0.05 10 × 16 3.2 0.7 1.2 5.0 0.6 ±0.05 10 × 20 3.2 0.7 1.2 5.0 0.6 ±0.05 12.5 × 20 3.2 0.7 1.2 5.0 0.6 ±0.05 12.5 × 25 3.2 0.7 1.2 5.0 0.6 ±0.05 16 × 20 3.5 0.7 1.6 7.5 0.8 ±0.05 16 × 25 3.5 0.7 1.6 7.5 0.8 ±0.05 16 × 31.5 3.5 0.7 1.6 7.5 0.8 ±0.05 18 × 20 3.5 0.7 1.6 7.5 0.8 ±0.1 18 × 25 3.5 0.7 1.6 7.5 0.8 ±0.1 18 × 31.5 3.5 0.7 1.6 7.5 0.8 ±0.1 18 × 35 3.5 0.7 1.6 7.5 0.8 ±0.1 Please read Cautions and warnings and Important notes at the end of this document. Page 23 of 30 a ±0.5 ∅b B41858 Low impedance 105 °C Bent 90° leads for horizontal mounting pinning Last 3 digits of ordering code: 012 Case size d × l (mm) Dimensions (mm) C ±0.5 E ±0.5 F ±0.5 a ±0.5 ∅b 16 × 20 4.0 4.0 12.0 7.5 0.8 ±0.05 16 × 25 4.0 4.0 12.0 7.5 0.8 ±0.05 16 × 31.5 4.0 4.0 12.0 7.5 0.8 ±0.05 18 × 20 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 25 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 31.5 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 35 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 40 4.0 4.0 13.0 7.5 0.8 ±0.1 Bent leads for diameter 12.5 mm available upon request. Please read Cautions and warnings and Important notes at the end of this document. Page 24 of 30 B41858 Low impedance 105 °C Overview of packing units and code numbers for case sizes 5 × 11 ... 16 × 31.5 PAPR Case size d×l Taped, Ammo pack mm Standard, bulk pcs. 5 × 11 2000 6.3 × 11 2500 2000 8 × 11.5 1000 1000 10 × 12.5 1000 750 10 × 16 100 500 1000 10 × 20 500 500 500 500 12.5 × 20 350 500 350 350 12.5 × 25 250 500 500 500 12.5 × 30 200 500 175 175 12.5 × 35 175 - 175 175 12.5 × 40 175 - 175 175 16 × 20 250 300 200 200 16 × 25 250 300 200 16 × 31.5 200 300 The last three digits of the complete ordering code state the lead configuration 000 Code 006 007 008 009 1) pcs. Kinked leads, bulk pcs. Cut Crimped J leads leads, leads bulk pcs. pcs. pcs. 2000 F (mm) d (mm) 3.5 2.5 5 7.5 1000 675 675 500 300 1) 225 1) 180 1) 150 1) 150 1) 200 200 120 200 200 200 120 250 250 344 344 120 001 002 003 004 012 8 5...6.3 5...12.5 16...18 Available upon request Please read Cautions and warnings and Important notes at the end of this document. Bent 90° leads, blister pcs. Page 25 of 30 B41858 Low impedance 105 °C Overview of packing units and code numbers for case sizes 18 × 20 ... 25 × 40 PAPR Case size d×l Taped, Ammo pack mm Standard, bulk pcs. pcs. Kinked leads, bulk pcs. Cut Crimped J leads leads, leads bulk pcs. pcs. pcs. Bent 90° leads, blister pcs. 18 × 20 175 18 × 25 150 250 175 175 200 200 120 250 150 150 200 200 18 × 31.5 120 100 250 100 100 150 150 120 18 × 35 100 100 100 150 150 150 18 × 40 125 100 100 120 72 20 × 20 125 125 125 200 20 × 25 125 125 125 200 20 × 30 100 100 100 120 20 × 35 100 100 100 120 20 × 40 100 100 100 120 22 × 30 80 100 100 22 × 35 80 100 100 22 × 40 80 100 100 25 × 40 40 100 The last three digits of the complete ordering code state the lead configuration 000 Code 007 008 009 001 002 Please read Cautions and warnings and Important notes at the end of this document. F (mm) d (mm) 2.5 5 7.5 4...6.3 6.3...12.5 16...18 Page 26 of 30 003 004 012 B41858 Low impedance 105 °C Cautions and warnings Personal safety The electrolytes used by EPCOS have not only been optimized with a view to the intended application, but also with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC). Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They contain flame-retarding substances which will quickly extinguish any flame that may have been ignited. As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes. However, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no safe substitute materials are currently known. However, the amount of dangerous materials used in our products has been limited to an absolute minimum. Nevertheless, the following rules should be observed when handling Al electrolytic capacitors: Any escaping electrolyte should not come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected parts immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. Please read Cautions and warnings and Important notes at the end of this document. Page 27 of 30 B41858 Low impedance 105 °C Product safety The table below summarize the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of chapter "General technical information". Topic Safety information Polarity Make sure that polar capacitors are connected with the right polarity. Reverse voltage Voltages polarity classes should be prevented by connecting a diode. Do not exceed the upper category temperatur. Upper category temperature Maintenance Mounting position of screw terminal capacitors Mounting of single-ended capacitors Robustness of terminals Soldering Make periodic inspections of the capacitors. Before the inspection, make sure that the power supply is turned off and carefully discharge the electricity of the capacitors. Do not apply any mechanical stress to the capacitor terminals. Do not mount the capacitor with the terminals (safety vent) upside down. Reference Chapter "General technical information" 1 "Basic construction of aluminum electrolytic capacitors" 3.1.6 "Reverse voltage" 7.2 "Maximum permissible operating temperature" 10 "Maintenance" 11.1. "Mounting positions of capacitors with screw terminals" The internal structure of single-ended capacitors 11.4 might be damaged if excessive force is applied to "Mounting the lead wires. considerations for Avoid any compressive, tensile or flexural stress. single-ended capacitors" Do not move the capacitor after soldering to PC board. Do not pick up the PC board by the soldered capacitor. Do not insert the capacitor on the PC board with a hole space different to the lead space specified. The following maximum tightening torques must 11.3 not be exceeded when connecting screw "Mounting torques" terminals: M5: 2 Nm M6: 2.5 Nm Do not exceed the specified time or temperature 11.5 limits during soldering. "Soldering" Please read Cautions and warnings and Important notes at the end of this document. Page 28 of 30 B41858 Low impedance 105 °C Topic Soldering, cleaning agents Passive flammability Active flammability Safety information Reference Chapter "General technical information" Do not allow halogenated hydrocarbons to come 11.6 into contact with aluminum electrolytic capacitors. "Cleaning agents" Avoid external energy, such as fire or electricity. 8.1 "Passive flammability" Avoid overload of the capacitors. 8.2 "Active flammability" Breakdown strength Do not damage the insulating sleeve, especially of insulating when ring clips are used for mounting. sleeves Please read Cautions and warnings and Important notes at the end of this document. Page 29 of 30 Reference Chapter "Capacitors with screw terminals" "Screw terminals accessories" Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as “hazardous”). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, EPCOS-JONES, BAOKE, Alu-X, CeraDiode, CSSP, MLSC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 30 of 30