AD ADA4932-2YCPZ-RL Low power, differential adc driver Datasheet

Low Power,
Differential ADC Driver
ADA4932-1/ADA4932-2
Data Sheet
FUNCTIONAL BLOCK DIAGRAM
13 –VS
14 –VS
16 –VS
+IN 2
11 –OUT
–IN 3
10 +OUT
07752-001
VOCM
+VS 8
+VS 7
+VS 6
9
+VS 5
+FB 4
Figure 1. ADA4932-1
19 –OUT1
20 PD1
22 –VS1
21 –VS1
24 +IN1
ADA4932-2
–IN1 1
18 +OUT1
+FB1 2
17 VOCM1
16 –VS2
+VS1 3
+VS1 4
15 –VS2
–FB2 5
14 PD2
+IN2 6
07752-002
VOCM2 11
+OUT2 12
+VS2 10
13 –OUT2
+VS2 9
ADC drivers
Single-ended-to-differential converters
IF and baseband gain blocks
Differential buffers
Line drivers
15 –VS
12 PD
–FB 1
–IN2 7
APPLICATIONS
ADA4932-1
23 –FB1
High performance at low power
High speed
−3 dB bandwidth of 560 MHz, G = 1
0.1 dB gain flatness to 300 MHz
Slew rate: 2800 V/μs, 25% to 75%
Fast 0.1% settling time of 9 ns
Low power: 9.6 mA per amplifier
Low harmonic distortion
100 dB SFDR at 10 MHz
90 dB SFDR at 20 MHz
Low input voltage noise: 3.6 nV/√Hz
±0.5 mV typical input offset voltage
Externally adjustable gain
Can be used with gains less than 1
Differential-to-differential or single-ended-to-differential
operation
Adjustable output common-mode voltage
Input common-mode range shifted down by 1 VBE
Wide supply range: +3 V to ±5 V
Available in 16-lead and 24-lead LFCSP packages
+FB2 8
FEATURES
Figure 2. ADA4932-2
GENERAL DESCRIPTION
The ADA4932-1/ADA4932-2 are the next generation AD8132
with higher performance and lower noise and power consumption.
They are an ideal choice for driving high performance ADCs as
a single-ended-to-differential or differential-to-differential
amplifier. The output common-mode voltage is user adjustable
by means of an internal common-mode feedback loop, allowing
the ADA4932-1/ADA4932-2 output to match the input of the
ADC. The internal feedback loop also provides exceptional
output balance as well as suppression of even-order harmonic
distortion products.
With the ADA4932-1/ADA4932-2, differential gain configurations
are easily realized with a simple external four-resistor feedback
network that determines the closed-loop gain of the amplifier.
Rev. E
The ADA4932-1/ADA4932-2 were fabricated using the
Analog Devices, Inc., proprietary silicon-germanium (SiGe)
complementary bipolar process, enabling it to achieve low levels
of distortion and noise at low power consumption.
The low offset and excellent dynamic performance of the
ADA4932-1/ADA4932-2 make them well suited for a wide
variety of data acquisition and signal processing applications.
The ADA4932-1 is available in a 16-lead LFCSP, and the
ADA4932-2 is available in a 24-lead LFCSP. The pinouts are
optimized to facilitate the printed circuit board (PCB) layout
and minimize distortion. The ADA4932-1/ADA4932-2 are
specified to operate over the −40°C to +105°C temperature
range; both operate on supplies between +3 V and ±5 V.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2008–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADA4932-1/ADA4932-2
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 19
Applications ....................................................................................... 1
Applications Information .............................................................. 20
Functional Block Diagram .............................................................. 1
Analyzing an Application Circuit ............................................ 20
General Description ......................................................................... 1
Setting the Closed-Loop Gain .................................................. 20
Revision History ............................................................................... 2
Estimating the Output Noise Voltage ...................................... 20
Specifications..................................................................................... 3
Impact of Mismatches in the Feedback Networks ................. 21
±5 V Operation ............................................................................. 3
Calculating the Input Impedance for an Application Circuit.... 21
5 V Operation ............................................................................... 5
Input Common-Mode Voltage Range ..................................... 23
Absolute Maximum Ratings ............................................................ 7
Input and Output Capacitive AC Coupling ............................ 23
Thermal Resistance ...................................................................... 7
Setting the Output Common-Mode Voltage .......................... 23
Maximum Power Dissipation ..................................................... 7
High Performance Precision ADC Driver .............................. 23
ESD Caution .................................................................................. 7
High Performance ADC Driving ................................................. 25
Pin Configurations and Function Descriptions ........................... 8
Layout, Grounding, and Bypassing .............................................. 26
Typical Performance Characteristics ............................................. 9
Outline Dimensions ....................................................................... 27
Test Circuits ..................................................................................... 17
Ordering Guide .......................................................................... 27
Terminology .................................................................................... 18
REVISION HISTORY
5/2016—Rev. D to Rev. E
Changed ADA4932 Family to ADA4932-1/ADA4932-2,
ADA4932-x to ADA4932-1/ADA4932-2, and CP-16-2 to
CP-16-21 ......................................................................... Throughout
Deleted Figure 2 and Figure 3; Renumbered Sequentially .......... 1
Added Figure 2.................................................................................. 1
Updated Outline Dimensions ....................................................... 27
Changes to Ordering Guide .......................................................... 27
4/2014—Rev. C to Rev. D
Changes to Features Section, Figure 2, and Figure 3 ................... 1
Changes to Setting the Output Common-Mode Voltage Section.. 23
Added High Performance Precision ADC Driver Section ....... 24
Moved Layout, Grounding, and Bypassing Section ................... 26
1/2014—Rev. B to Rev. C
Changes to Figure 51...................................................................... 16
3/2013—Rev. A to Rev. B
Updated Outline Dimensions ....................................................... 26
Changes to Ordering Guide .......................................................... 26
8/2009—Rev. 0 to Rev. A
Changes to Features Section ............................................................1
Changes to Figure 11.........................................................................9
Changes to Figure 43 and Figure 45 ............................................ 15
Changes to Figure 52, Figure 53, and Figure 54 ......................... 17
10/2008—Revision 0: Initial Version
Rev. E | Page 2 of 27
Data Sheet
ADA4932-1/ADA4932-2
SPECIFICATIONS
±5 V OPERATION
TA = 25°C, +VS = 5 V, −VS = −5 V, VOCM = 0 V, RF = 499 Ω, RG = 499 Ω, RT = 53.6 Ω (when used), RL, dm = 1 kΩ, unless otherwise noted.
All specifications refer to single-ended input and differential outputs, unless otherwise noted. Refer to Figure 54 for signal definitions.
±DIN to VOUT, dm Performance
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
−3 dB Large Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
Third Harmonic
IMD
Voltage Noise (RTI)
Input Current Noise
Crosstalk
INPUT CHARACTERISTICS
Offset Voltage
Test Conditions/Comments
Min
VOUT, dm = 0.1 V p-p
VOUT, dm = 0.1 V p-p, RF = RG = 205 Ω
VOUT, dm = 2.0 V p-p
VOUT, dm = 2.0 V p-p, RF = RG = 205 Ω
VOUT, dm = 2.0 V p-p, ADA4932-1, RL = 200 Ω
VOUT, dm = 2.0 V p-p, ADA4932-2, RL = 200 Ω
VOUT, dm = 2 V p-p, 25% to 75%
VOUT, dm = 2 V step
VIN = 0 V to 5 V ramp, G = 2
See Figure 53 for distortion test circuit
VOUT, dm = 2 V p-p, 1 MHz
VOUT, dm = 2 V p-p, 10 MHz
VOUT, dm = 2 V p-p, 20 MHz
VOUT, dm = 2 V p-p, 50 MHz
VOUT, dm = 2 V p-p, 1 MHz
VOUT, dm = 2 V p-p, 10 MHz
VOUT, dm = 2 V p-p, 20 MHz
VOUT, dm = 2 V p-p, 50 MHz
f1 = 30 MHz, f2 = 30.1 MHz, VOUT, dm = 2 V p-p
f = 1 MHz
f = 1 MHz
f = 10 MHz, ADA4932-2
V+DIN = V−DIN = VOCM = 0 V
TMIN to TMAX variation
Input Bias Current
−2.2
−5.2
TMIN to TMAX variation
Input Offset Current
Input Resistance
−0.2
Differential
Common mode
Input Capacitance
Input Common-Mode Voltage Range
CMRR
Open-Loop Gain
OUTPUT CHARACTERISTICS
Output Voltage Swing
Linear Output Current
Output Balance Error
∆VOUT, dm/∆VIN, cm, ∆VIN, cm = ±1 V
64
Maximum ∆VOUT, single-ended output,
RF = RG = 10 kΩ, RL = 1 kΩ
200 kHz, RL, dm = 10 Ω, SFDR = 68 dB
∆VOUT, cm/∆VOUT, dm, ∆VOUT, dm = 2 V p-p, 1 MHz,
see Figure 52 for output balance test circuit
Rev. E | Page 3 of 27
−VS + 1.4 to
+VS − 1.4
Typ
Max
Unit
560
1000
360
360
300
100
2800
9
20
MHz
MHz
MHz
MHz
MHz
MHz
V/μs
ns
ns
−110
−100
−90
−72
−130
−120
−105
−80
−91
3.6
1.0
−100
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
nV/√Hz
pA/√Hz
dB
±0.5
−3.7
−2.5
−9.5
±0.025
11
16
0.5
−VS + 0.2 to
+VS − 1.8
−100
66
−VS + 1.2 to
+VS − 1.2
80
−64
+2.2
−0.1
+0.2
−87
mV
μV/°C
μA
nA/°C
μA
MΩ
MΩ
pF
V
dB
dB
V
−60
mA rms
dB
ADA4932-1/ADA4932-2
Data Sheet
VOCM to VOUT, cm Performance
Table 2.
Parameter
VOCM DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
−3 dB Large Signal Bandwidth
Slew Rate
Input Voltage Noise (RTI)
VOCM INPUT CHARACTERISTICS
Input Voltage Range
Input Resistance
Input Offset Voltage
VOCM CMRR
Gain
Test Conditions/Comments
Min
VOUT, cm = 100 mV p-p
VOUT, cm = 2 V p-p
VIN = 1.5 V to 3.5 V, 25% to 75%
f = 1 MHz
V+DIN = V−DIN = 0 V
ΔVOUT, dm/ΔVOCM, ΔVOCM = ±1 V
ΔVOUT, cm/ΔVOCM, ΔVOCM = ±1 V
Typ
Max
270
105
410
9.6
22
−5.1
0.995
Unit
MHz
MHz
V/µs
nV/√Hz
−VS + 1.2 to +VS − 1.2
25
±1
−100
0.998
29
+5.1
−86
1.000
V
kΩ
mV
dB
V/V
Max
Unit
11
10.1
V
mA
µA/°C
mA
dB
General Performance
Table 3.
Parameter
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
Power Supply Rejection Ratio
POWER-DOWN (PD)
PD Input Voltage
Turn-Off Time
Turn-On Time
PD Pin Bias Current per Amplifier
Enabled
Disabled
Test Conditions/Comments
Min
3.0
9.0
TMIN to TMAX variation
Powered down
ΔVOUT, dm/ΔVS, ΔVS = 1 V p-p
Powered down
Enabled
Typ
9.6
35
0.9
−96
1.0
−84
≤(+VS − 2.5)
≥(+VS − 1.8)
1100
16
PD = 5 V
PD = 0 V
−10
−240
OPERATING TEMPERATURE RANGE
−40
Rev. E | Page 4 of 27
+0.7
−195
V
V
ns
ns
+10
−140
µA
µA
+105
°C
Data Sheet
ADA4932-1/ADA4932-2
5 V OPERATION
TA = 25°C, +VS = 5 V, −VS = 0 V, VOCM = 2.5 V, RF = 499 Ω, RG = 499 Ω, RT = 53.6 Ω (when used), RL, dm = 1 kΩ, unless otherwise noted.
All specifications refer to single-ended input and differential outputs, unless otherwise noted. Refer to Figure 54 for signal definitions.
±DIN to VOUT, dm Performance
Table 4.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
−3 dB Large Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
Third Harmonic
IMD
Voltage Noise (RTI)
Input Current Noise
Crosstalk
INPUT CHARACTERISTICS
Offset Voltage
Test Conditions/Comments
Min
VOUT, dm = 0.1 V p-p
VOUT, dm = 0.1 V p-p, RF = RG = 205 Ω
VOUT, dm = 2.0 V p-p
VOUT, dm = 2.0 V p-p, RF = RG = 205 Ω
VOUT, dm = 2.0 V p-p, ADA4932-1, RL = 200 Ω
VOUT, dm = 2.0 V p-p, ADA4932-2, RL = 200 Ω
VOUT, dm = 2 V p-p, 25% to 75%
VOUT, dm = 2 V step
VIN = 0 V to 2.5 V ramp, G = 2
See Figure 53 for distortion test circuit
VOUT, dm = 2 V p-p, 1 MHz
VOUT, dm = 2 V p-p, 10 MHz
VOUT, dm = 2 V p-p, 20 MHz
VOUT, dm = 2 V p-p, 50 MHz
VOUT, dm = 2 V p-p, 1 MHz
VOUT, dm = 2 V p-p, 10 MHz
VOUT, dm = 2 V p-p, 20 MHz
VOUT, dm = 2 V p-p, 50 MHz
f1 = 30 MHz, f2 = 30.1 MHz, VOUT, dm = 2 V p-p
f = 1 MHz
f = 1 MHz
f = 10 MHz, ADA4932-2
V+DIN = V−DIN = VOCM = 2.5 V
TMIN to TMAX variation
Input Bias Current
−2.2
−5.3
TMIN to TMAX variation
Input Offset Current
Input Resistance
−0.25
Differential
Common mode
Input Capacitance
Input Common-Mode Voltage Range
CMRR
Open-Loop Gain
OUTPUT CHARACTERISTICS
Output Voltage Swing
Linear Output Current
Output Balance Error
∆VOUT, dm/∆VIN, cm, ∆VIN, cm = ±1 V
64
Maximum ∆VOUT, single-ended output,
RF = RG = 10 kΩ, RL = 1 kΩ
200 kHz, RL, dm = 10 Ω, SFDR = 67 dB
∆VOUT, cm/∆VOUT, dm, ∆VOUT, dm = 1 V p-p, 1 MHz,
see Figure 52 for output balance test circuit
Rev. E | Page 5 of 27
−VS + 1.15 to
+VS − 1.15
Typ
Max
Unit
560
990
315
320
120
200
2200
10
20
MHz
MHz
MHz
MHz
MHz
MHz
V/μs
ns
ns
−110
−100
−90
−72
−120
−100
−87
−70
−91
3.6
1.0
−100
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
nV/√Hz
pA/√Hz
dB
±0.5
−3.7
−3.0
−9.5
±0.025
11
16
0.5
−VS + 0.2 to
+VS − 1.8
−100
66
−VS + 1.02 to
+VS − 1.02
53
−64
+2.2
−0.23
+0.25
−87
mV
μV/°C
μA
nA/°C
μA
MΩ
MΩ
pF
V
dB
dB
V
−60
mA rms
dB
ADA4932-1/ADA4932-2
Data Sheet
VOCM to VOUT, cm Performance
Table 5.
Parameter
VOCM DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
−3 dB Large Signal Bandwidth
Slew Rate
Input Voltage Noise (RTI)
VOCM INPUT CHARACTERISTICS
Input Voltage Range
Input Resistance
Input Offset Voltage
VOCM CMRR
Gain
Test Conditions/Comments
Min
VOUT, cm = 100 mV p-p
VOUT, cm = 2 V p-p
VIN = 1.5 V to 3.5 V, 25% to 75%
f = 1 MHz
V+DIN = V−DIN = 2.5 V
ΔVOUT, dm/ΔVOCM, ΔVOCM = ±1 V
ΔVOUT, cm/ΔVOCM, ΔVOCM = ±1 V
Typ
Max
260
90
360
9.6
22
−6.5
0.995
Unit
MHz
MHz
V/µs
nV/√Hz
−VS + 1.2 to +VS − 1.2
25
−3.0
−100
0.998
29
+6.5
−86
1.000
V
kΩ
mV
dB
V/V
General Performance
Table 6.
Parameter
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
Power Supply Rejection Ratio
POWER-DOWN (PD)
PD Input Voltage
Turn-Off Time
Turn-On Time
PD Pin Bias Current per Amplifier
Enabled
Disabled
Test Conditions/Comments
Min
3.0
8.2
TMIN to TMAX variation
Powered down
ΔVOUT, dm/ΔVS, ΔVS = 1 V p-p
Powered down
Enabled
Typ
8.8
35
0.7
−96
Max
Unit
11
9.5
V
mA
µA/°C
mA
dB
0.8
−84
≤(+VS − 2.5)
≥(+VS − 1.8)
1100
16
PD = 5 V
PD = 0 V
−10
−100
OPERATING TEMPERATURE RANGE
−40
Rev. E | Page 6 of 27
+0.7
−70
V
V
ns
ns
+10
−40
µA
µA
+105
°C
Data Sheet
ADA4932-1/ADA4932-2
ABSOLUTE MAXIMUM RATINGS
Table 7.
Rating
11 V
See Figure 3
±5 mA
−65°C to +125°C
−40°C to +105°C
−40°C to +105°C
300°C
150°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Airflow increases heat dissipation, effectively reducing θJA. In
addition, more metal directly in contact with the package leads/
exposed pad from metal traces, through holes, ground, and power
planes reduces θJA.
Figure 3 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the single 16-lead
LFCSP (91°C/W) and the dual 24-lead LFCSP (65°C/W) on a
JEDEC standard 4-layer board with the exposed pad soldered to
a PCB pad that is connected to a solid plane.
3.5
θJA is specified for the device (including exposed pad) soldered
to a high thermal conductivity 2s2p circuit board, as described
in EIA/JESD 51-7.
Table 8. Thermal Resistance
Package Type
ADA4932-1, 16-Lead LFCSP (Exposed Pad)
ADA4932-2, 24-Lead LFCSP (Exposed Pad)
θJA
91
65
Unit
°C/W
°C/W
MAXIMUM POWER DISSIPATION (W)
THERMAL RESISTANCE
MAXIMUM POWER DISSIPATION
The maximum safe power dissipation for the ADA4932-1/
ADA4932-2 package is limited by the associated rise in junction
temperature (TJ) on the die. At approximately 150°C, which is
the glass transition temperature, the plastic changes its properties.
Even temporarily exceeding this temperature limit can change
the stresses that the package exerts on the die, permanently
shifting the parametric performance of the ADA4932-1/
ADA4932-2. Exceeding a junction temperature of 150°C for an
extended period can result in changes in the silicon devices,
potentially causing failure.
3.0
2.5
ADA4932-2
2.0
1.5
ADA4932-1
1.0
0.5
0
–40
–20
0
20
40
60
AMBIENT TEMPERATURE (°C)
80
100
07752-204
Parameter
Supply Voltage
Power Dissipation
Input Current, +IN, −IN, PD
Storage Temperature Range
Operating Temperature Range
ADA4932-1
ADA4932-2
Lead Temperature (Soldering, 10 sec)
Junction Temperature
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive. The quiescent power is the voltage
between the supply pins (VS) times the quiescent current (IS).
The power dissipated due to the load drive depends upon the
particular application. The power due to load drive is calculated
by multiplying the load current by the associated voltage drop
across the device. RMS voltages and currents must be used in
these calculations.
Figure 3. Maximum Power Dissipation vs. Ambient Temperature for
a 4-Layer Board
ESD CAUTION
Rev. E | Page 7 of 27
ADA4932-1/ADA4932-2
Data Sheet
19 –OUT1
21 –VS1
20 PD1
22 –VS1
24 +IN1
–IN1 1
18 +OUT1
+FB1 2
17 VOCM1
12 PD
+VS1 3
ADA4932-2
16 –VS2
+IN 2
ADA4932-1
11 –OUT
+VS1 4
15 –VS2
–IN 3
TOP VIEW
(Not to Scale)
10 +OUT
–FB2 5
TOP VIEW
(Not to Scale)
VOCM
+IN2 6
14 PD2
+OUT2 12
VOCM2 11
+VS2 10
+VS2 9
13 –OUT2
–IN2 7
NOTES
1. SOLDER EXPOSED PADDLE ON BACK OF PACKAGE
TO GROUND PLANE OR TO A POWER PLANE.
07752-005
+VS 8
+VS 7
+VS 6
+VS 5
9
+FB2 8
+FB 4
NOTES
1. SOLDER EXPOSED PADDLE ON BACK OF PACKAGE
TO GROUND PLANE OR TO A POWER PLANE.
07752-006
–FB 1
23 –FB1
13 –VS
14 –VS
16 –VS
15 –VS
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Figure 5. ADA4932-2 Pin Configuration
Figure 4. ADA4932-1 Pin Configuration
Table 9. ADA4932-1 Pin Function Descriptions
Pin No.
1
2
3
4
5 to 8
9
10
11
12
13 to 16
17
Mnemonic
−FB
+IN
−IN
+FB
+VS
VOCM
+OUT
−OUT
PD
−VS
Exposed Paddle (EPAD)
Description
Negative Output for Feedback Component Connection.
Positive Input Summing Node.
Negative Input Summing Node.
Positive Output for Feedback Component Connection.
Positive Supply Voltage.
Output Common-Mode Voltage.
Positive Output for Load Connection.
Negative Output for Load Connection.
Power-Down Pin.
Negative Supply Voltage.
Solder the exposed paddle on the back of the package to a ground plane or to a power plane.
Table 10. ADA4932-2 Pin Function Descriptions
Pin No.
1
2
3, 4
5
6
7
8
9, 10
11
12
13
14
15, 16
17
18
19
20
21, 22
23
24
25
Mnemonic
−IN1
+FB1
+VS1
−FB2
+IN2
−IN2
+FB2
+VS2
VOCM2
+OUT2
−OUT2
PD2
−VS2
VOCM1
+OUT1
−OUT1
PD1
−VS1
−FB1
+IN1
Exposed Paddle (EPAD)
Description
Negative Input Summing Node 1.
Positive Output Feedback 1.
Positive Supply Voltage 1.
Negative Output Feedback 2.
Positive Input Summing Node 2.
Negative Input Summing Node 2.
Positive Output Feedback 2.
Positive Supply Voltage 2.
Output Common-Mode Voltage 2.
Positive Output 2.
Negative Output 2.
Power-Down Pin 2.
Negative Supply Voltage 2.
Output Common-Mode Voltage 1.
Positive Output 1.
Negative Output 1.
Power-Down Pin 1.
Negative Supply Voltage 1.
Negative Output Feedback 1.
Positive Input Summing Node 1.
Solder the exposed paddle on the back of the package to a ground plane or to a power plane.
Rev. E | Page 8 of 27
Data Sheet
ADA4932-1/ADA4932-2
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, +VS = 5 V, −VS = −5 V, VOCM = 0 V, RG = 499 Ω, RF = 499 Ω, RT = 53.6 Ω (when used), RL, dm = 1 kΩ, unless otherwise noted.
Refer to Figure 51 for test setup. Refer to Figure 54 for signal definitions.
2
0
NORMALIZED CLOSED-LOOP GAIN (dB)
1
GAIN = 1
GAIN = 2
–1
–2
–3
–4
–5
–6
–7
–8
1M
10M
100M
FREQUENCY (Hz)
–4
–5
–6
–7
1M
10M
100M
FREQUENCY (Hz)
1G
Figure 9. Large Signal Frequency Response for Various Gains
RF = RG = 499Ω
RF = RG = 205Ω
VOUT, dm = 2V p-p
RF = RG = 499Ω
1
0
CLOSED-LOOP GAIN (dB)
–1
–2
–3
–4
–5
RF = RG = 205Ω
–1
–2
–3
–4
–5
–6
07752-008
–6
–8
1M
10M
100M
FREQUENCY (Hz)
1G
–7
–8
10G
100
1k
Figure 10. Large Signal Frequency Response for Various RF and RG
2
VOUT, dm = 100mV p-p
1
10
FREQUENCY (MHz)
Figure 7. Small Signal Frequency Response for Various RF and RG
2
1
07752-058
–7
VOUT, dm = 2V p-p
1
0
CLOSED-LOOP GAIN (dB)
0
VS = ±5V
VS = ±2.5V
–1
–2
–3
–4
–5
VS = ±5V
VS = ±2.5V
–1
–2
–3
–4
–5
–6
07752-009
–6
–7
–8
1M
10M
100M
FREQUENCY (Hz)
07752-012
CLOSED-LOOP GAIN (dB)
–3
–8
0
CLOSED-LOOP GAIN (dB)
–2
2
VOUT, dm = 100mV p-p
1
0
GAIN = 1
GAIN = 2
–1
1G
Figure 6. Small Signal Frequency Response for Various Gains
2
VIN = 2V p-p
RF = 499Ω
RG = 499Ω, 249Ω
1
07752-010
VIN = 100mV p-p
RF = 499Ω
RG = 499Ω, 249Ω
07752-007
NORMALIZED CLOSED-LOOP GAIN (dB)
2
–7
–8
1M
1G
10M
100M
FREQUENCY (Hz)
1G
Figure 11. Large Signal Frequency Response for Various Supplies
Figure 8. Small Signal Frequency Response for Various Supplies
Rev. E | Page 9 of 27
ADA4932-1/ADA4932-2
2
Data Sheet
2
VOUT, dm = 100mV p-p
1
0
CLOSED-LOOP GAIN (dB)
–1
TA = –40°C
TA = +25°C
TA = +105°C
–2
–3
–4
–5
–3
–4
–5
–8
1M
10M
100M
FREQUENCY (Hz)
–7
–8
1G
1M
Figure 12. Small Signal Frequency Response for Various Temperatures
2
VOUT, dm = 100mV p-p
1
07752-016
–7
10M
100M
FREQUENCY (Hz)
1G
Figure 15. Large Signal Frequency Response for Various Temperatures
2
RL = 1kΩ
RL = 200Ω
VOUT, dm = 2V p-p
1
RL = 1kΩ
RL = 200Ω
0
CLOSED-LOOP GAIN (dB)
0
–1
–2
–3
–4
–5
–2
–3
–4
–5
–6
07752-014
–6
–1
–7
–8
1M
10M
100M
FREQUENCY (Hz)
–7
–8
1G
1M
Figure 13. Small Signal Frequency Response at Various Loads
2
10M
100M
FREQUENCY (Hz)
1G
Figure 16. Large Signal Frequency Response at Various Loads
2
VOUT, dm = 100mV p-p
1
07752-017
CLOSED-LOOP GAIN (dB)
TA = –40°C
TA = +25°C
TA = +105°C
–2
–6
07752-013
–6
–1
VOUT, dm = 2V p-p
1
0
CLOSED-LOOP GAIN (dB)
0
–1
VOCM = 0V
VOCM = +2.5V
VOCM = –2.5V
–2
–3
–4
–5
VOCM = 0V
VOCM = +2.5V
VOCM = –2.5V
–2
–3
–4
–5
–6
07752-015
–6
–1
–7
–8
1M
10M
100M
FREQUENCY (Hz)
07752-018
CLOSED-LOOP GAIN (dB)
0
CLOSED-LOOP GAIN (dB)
VOUT, dm = 2V p-p
1
–7
–8
1G
1M
Figure 14. Small Signal Frequency Response for Various VOCM Levels
10M
100M
FREQUENCY (Hz)
1G
Figure 17. Large Signal Frequency Response for Various VOCM Levels
Rev. E | Page 10 of 27
Data Sheet
ADA4932-1/ADA4932-2
4
4
VOUT, dm = 100mV p-p
VOUT, dm = 2V p-p
2
CLOSED-LOOP GAIN (dB)
CL = 0pF
CL = 0.9pF
CL = 1.8pF
–2
–4
–6
1M
10M
100M
FREQUENCY (Hz)
1G
0.5
1G
0.2
0.1
0
–0.1
ADA4932-1, R L = 1kΩ
ADA4932-1, R L = 200Ω
ADA4932-2, CH 1, R L = 1kΩ
ADA4932-2, CH 1, R L = 200Ω
ADA4932-2, CH 2, R L = 1kΩ
ADA4932-2, CH 2, R L = 200Ω
–0.2
–0.3
–0.4
10M
100M
FREQUENCY (Hz)
–0.1
ADA4932-1,
ADA4932-1,
ADA4932-2,
ADA4932-2,
ADA4932-2,
ADA4932-2,
–0.2
R L = 1kΩ
R L = 200Ω
CH 1, R L = 1kΩ
CH 1, R L = 200Ω
CH 2, R L = 1kΩ
CH 2, R L = 200Ω
–0.5
1G
1M
10M
100M
FREQUENCY (Hz)
1G
Figure 22. 0.1 dB Flatness Large Signal Frequency Response for Various Loads
2
VOUT, cm = 100mV p-p
1
0
–0.4
Figure 19. 0.1 dB Flatness Small Signal Frequency Response for Various Loads
2
0.1
–0.3
–0.5
1M
0.2
07752-023
CLOSED-LOOP GAIN (dB)
0.3
07752-020
CLOSED-LOOP GAIN (dB)
100M
FREQUENCY (Hz)
VOUT, dm = 2V p-p
0.4
0.3
VOUT, cm = 2V p-p
1
0
0
–1
–1
–3
VOCM GAIN (dB)
VOCM (DC) = 0V
VOCM (DC) = +2.5V
VOCM (DC) = –2.5V
–2
–4
–2
–3
–4
–5
–5
–6
–6
07752-021
VOCM GAIN (dB)
–6
Figure 21. Large Signal Frequency Response at Various Capacitive Loads
VOUT, dm = 100mV p-p
0.4
–4
–10
10M
10G
Figure 18. Small Signal Frequency Response at Various Capacitive Loads
0.5
CL = 0pF
CL = 0.9pF
CL = 1.8pF
–2
–8
07752-019
–8
0
07752-022
0
–7
–8
1M
10M
100M
FREQUENCY (Hz)
–7
–8
1M
1G
VOCM (DC) = 0V
VOCM (DC) = +2.5V
VOCM (DC) = –2.5V
10M
100M
FREQUENCY (Hz)
Figure 20. VOCM Small Signal Frequency Response at Various DC Levels
1G
07752-224
CLOSED-LOOP GAIN (dB)
2
Figure 23. VOCM Large Signal Frequency Response at Various DC Levels
Rev. E | Page 11 of 27
ADA4932-1/ADA4932-2
–60
–70
–80
–90
–100
–110
07752-025
–120
–130
–140
100k
1M
10M
FREQUENCY (Hz)
±5.0V
±5.0V
±2.5V
±2.5V
–90
–100
–110
–120
–130
–140
100k
–30
1M
10M
FREQUENCY (Hz)
–110
–120
HD2,
HD3,
HD2,
HD3,
–70
–90
–100
–110
–120
–70
–80
–90
–100
–110
–4
–3
–2
–1
0
1
VOCM (V p-p)
2
3
2
3
4
5
6
VOUT, dm (V p-p)
7
8
9
10
VOUT = 2V p-p
–40
HD2 AT 10MHz
HD3 AT 10MHz
HD2 AT 30MHz
HD3 AT 30MHz
–50
–60
–70
–80
–90
–100
07752-030
10MHz
10MHz
30MHz
30MHz
–130
1
Figure 28. Harmonic Distortion vs. VOUT, dm and Supply Voltage, f = 10 MHz
–20
–120
±5.0V
±5.0V
±2.5V
±2.5V
–80
0
HARMONIC DISTORTION (dBc)
–60
100M
VOCM = 0V
–30
HD2 AT
HD3 AT
HD2 AT
HD3 AT
10M
FREQUENCY (Hz)
–140
VOUT = 2V p-p
–50
1M
–60
100M
07752-027
HARMONIC DISTORTION (dBc)
–100
–130
Figure 25. Harmonic Distortion vs. Frequency at Various Supplies
–40
–90
–50
HARMONIC DISTORTION (dBc)
–80
–80
–40
07752-026
HARMONIC DISTORTION (dBc)
HD2,
HD3,
HD2,
HD3,
=1
=1
=2
=2
Figure 27. Harmonic Distortion vs. Frequency at Various Gains
–60
–70
–70
G
G
G
G
–140
100k
100M
VOUT, dm = 2V p-p
VOCM = 0V
–50
HD2,
HD3,
HD2,
HD3,
–60
–130
Figure 24. Harmonic Distortion vs. Frequency at Various Loads
–40
VOUT, dm = 2V p-p
–50
RL = 1kΩ
RL = 1kΩ
RL = 200Ω
RL = 200Ω
07752-028
HD2,
HD3,
HD2,
HD3,
HARMONIC DISTORTION (dBc)
–50
HARMONIC DISTORTION (dBc)
–40
VOUT, dm = 2V p-p
07752-029
–40
Data Sheet
–110
–120
4
1.4
Figure 26. Harmonic Distortion vs. VOCM at Various Frequencies, ±5 V Supplies
1.6
1.8
2.0
2.2
2.4
2.6
VOCM (V)
2.8
3.0
3.2
3.4
Figure 29. Harmonic Distortion vs. VOCM at Various Frequencies, +5 V Supply
Rev. E | Page 12 of 27
Data Sheet
ADA4932-1/ADA4932-2
–40
–70
–80
–90
–100
–110
–120
–130
–140
100k
1M
10M
FREQUENCY (Hz)
–110
–120
0
RL = 200Ω
–90
–100
RL = 1kΩ
–120
–130
1M
10M
FREQUENCY (Hz)
100M
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
29.6
100M
29.7
29.8
29.9
30.0
30.1
30.2
30.3
30.4
30.5
FREQUENCY (MHz)
Figure 34. 30 MHz Intermodulation Distortion
–20
0
RL, dm = 200Ω
RL, dm = 200Ω
–20
–40
–40
PSSR (dB)
–50
–60
–70
–60
–80
–PSRR
–100
–80
+PSRR
–120
–100
1M
10M
100M
FREQUENCY (Hz)
07752-036
–90
07752-033
CMMR (dB)
10M
FREQUENCY (Hz)
VOUT, dm = 2V p-p
Figure 31. Spurious-Free Dynamic Range vs. Frequency at Various Loads
–30
1M
–10
NORMALIZED SPECTRUM (dBc)
–70
07752-032
SPURIOUS-FREE DYNAMIC RANGE (dBc)
–100
10
–60
–140
100k
–90
Figure 33. Harmonic Distortion vs. Frequency at Various RF and RG
–50
–110
–80
–140
100k
100M
VOUT, dm = 2V p-p
–80
–70
RF = RG = 499Ω
RF = RG = 499Ω
RF = RG = 200Ω
RF = RG = 200Ω
–130
Figure 30. Harmonic Distortion vs. Frequency at Various VOUT, dm
–40
HD2,
HD3,
HD2,
HD3,
–60
07752-235
–60
VOUT, dm = 2V p-p
–50
2V p-p
2V p-p
4V p-p
4V p-p
HARMONIC DISTORTION (dBc)
HD2,
HD3,
HD2,
HD3,
07752-031
HARMONIC DISTORTION (dBc)
–50
07752-034
–40
–140
1G
1M
Figure 32. CMRR vs. Frequency
10M
100M
FREQUENCY (Hz)
Figure 35. PSRR vs. Frequency
Rev. E | Page 13 of 27
1G
ADA4932-1/ADA4932-2
Data Sheet
–10
80
90
60
45
RL, dm = 200Ω
–40
–50
10M
100M
07752-237
–70
1M
1G
FREQUENCY (Hz)
–45
0
–90
PHASE
–20
–135
–40
–180
–60
–225
–80
1k
10k
100M
1G
–270
10G
100
OUTPUT IMPEDANCE (Ω)
–20
S22
–30
RL = 200Ω
10M
Figure 39. Open-Loop Gain and Phase vs. Frequency
INPUT SINGLE-ENDED, 50Ω LOAD TERMINATION
OUTPUT DIFFERENTIAL, 100Ω SOURCE TERMINATION
S11: COMMON-MODE-TO-COMMON-MODE
S22: DIFFERENTIAL-TO-DIFFERENTIAL
–10
1M
FREQUENCY (Hz)
Figure 36. Output Balance vs. Frequency
0
100k
PHASE (Degrees)
20
–60
S-PARAMETERS (dB)
0
GAIN
07752-240
40
–30
GAIN (dB)
OUTPUT BALANCE (dB)
–20
S11
–40
10
1
–60
1M
10M
100M
FREQUENCY (Hz)
0.1
100k
1G
1M
Figure 37. Return Loss (S11, S22) vs. Frequency
100M
1G
Figure 40. Closed-Loop Output Impedance Magnitude vs. Frequency, G = 1
100
10
2 × VIN
8
6
VOUT, dm
VOLTAGE (V)
4
10
2
0
–2
–4
–6
10
100
1k
10k
FREQUENCY (Hz)
100k
–8
–10
1M
0
100
200
300
400
500
600
700
800
TIME (ns)
Figure 41.Overdrive Recovery, G = 2
Figure 38. Voltage Noise Spectral Density, Referred to Input
Rev. E | Page 14 of 27
900
1000
07752-242
1
07752-039
INPUT VOLTAGE NOISE (nV/√Hz)
10M
FREQUENCY (Hz)
07752-241
07752-038
–50
Data Sheet
ADA4932-1/ADA4932-2
1.5
0.06
1.0
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
0.04
0.02
0
–0.02
0.5
0
–0.5
–1.0
0
5
10
15
20
25
30
TIME (ns)
07752-059
–1.5
–0.06
07752-146
–0.04
0
Figure 42. Small Signal Pulse Response
5
10
15
TIME (ns)
20
25
30
Figure 45. Large Signal Pulse Response
0.08
1.5
0.06
1.0
OUTPUT VOLTAGE (V)
0.02
0
–0.02
CL = 0pF
CL = 0.9pF
CL = 1.8pF
10
15
20
25
30
TIME (ns)
Figure 43. Small Signal Pulse Response for Various Capacitive Loads
0
10
15
20
25
30
Figure 46. Large Signal Pulse Response for Various Capacitive Loads
0.06
1.5
0.04
1.0
0.02
0
–0.02
–0.04
0.5
0
–0.5
–1.0
0
5
10
15
20
25
TIME (ns)
30
07752-060
–0.06
5
TIME (ns)
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
–1.5
07752-244
–0.08
5
CL = 0pF
CL = 0.9pF
CL = 1.8pF
–0.5
–1.0
–0.06
0
0
07752-247
–0.04
0.5
–1.5
07752-148
OUTPUT VOLTAGE (V)
0.04
0
5
10
15
TIME (ns)
20
25
Figure 47. VOCM Large Signal Pulse Response
Figure 44. VOCM Small Signal Pulse Response
Rev. E | Page 15 of 27
30
ADA4932-1/ADA4932-2
Data Sheet
1.2
0.4
0.1
OUTPUT
0
0.8
0
ERROR
–0.4
–0.1
–0.8
–0.2
–1.2
–0.3
–1.6
–0.4
–2.0
0
2
4
6
8
10
12
TIME (ns)
14
16
18
20
–0.5
VOUT, dm = 2V p-p
RL, dm = 200Ω
CHANNEL 1 TO CHANNEL 2
CHANNEL 2 TO CHANNEL 1
–40
–60
–80
–100
–120
07752-150
–140
–160
1M
10M
100M
FREQUENCY (Hz)
VOUT, dm
0.6
2
0.4
0
0.2
–2
0
–4
–0.2
–6
–0.4
–8
–0.6
–10
0
0.5
1.0
1.5
2.0
2.5
3.0
Figure 50. PD Response Time
0
1G
Figure 49. Crosstalk vs. Frequency, ADA4932-2
Rev. E | Page 16 of 27
6
4
TIME (µs)
Figure 48. Settling Time
–20
PD
3.5
4.0
PD VOLTAGE (V)
0.2
OUTPUT VOLTAGE (V)
INPUT
0.8
1.0
ERROR (%)
0.3
07752-149
0.4
1.2
8
GAIN = 9
RL, dm = 200Ω
07752-252
0.5
1.6
CROSSTALK (dB)
VOLTAGE (V)
2.0
Data Sheet
ADA4932-1/ADA4932-2
TEST CIRCUITS
499Ω
DC-COUPLED
GENERATOR
+5V
50Ω
499Ω
53.6Ω
VIN
ADA4932-1/
ADA4932-2
VOCM
1kΩ
499Ω
07752-043
25.5Ω
–5V
499Ω
Figure 51. Equivalent Basic Test Circuit, G = 1
NETWORK
ANALYZER
INPUT
NETWORK
ANALYZER
OUTPUT
AC-COUPLED
499Ω
50Ω
+5V
50Ω
499Ω
ADA4932-1/
ADA4932-2
VOCM
53.6Ω
VIN
49.9Ω
499Ω
NETWORK
ANALYZER
INPUT
–5V
499Ω
0.1µF
49.9Ω
50Ω
07752-044
25.5Ω
Figure 52. Test Circuit for Output Balance, CMRR
499Ω
DC-COUPLED
GENERATOR
VIN
0.1µF 442Ω
499Ω
LOW-PASS
FILTER
53.6Ω
VOCM
ADA4932-1/
ADA4932-2
499Ω
261Ω
200Ω
2:1
50Ω
DUAL
FILTER
HP
LP
CT
0.1µF 442Ω
25.5Ω
–5V
499Ω
Figure 53. Test Circuit for Distortion Measurements
Rev. E | Page 17 of 27
07752-045
50Ω
+5V
ADA4932-1/ADA4932-2
Data Sheet
TERMINOLOGY
Common-Mode Voltage
Common-mode voltage refers to the average of two node voltages
with respect to the local ground reference. The output commonmode voltage is defined as
–FB
RG
+IN
–DIN
–OUT
ADA4932-1/
ADA4932-2
VOCM
RG R
F
–IN
RL, dm VOUT, dm
+OUT
+FB
VOUT, cm = (V+OUT + V−OUT)/2
07752-046
+DIN
RF
Figure 54. Signal and Circuit Definitions
Differential Voltage
Differential voltage refers to the difference between two node
voltages. For example, the output differential voltage (or
equivalently, output differential mode voltage) is defined as
VOUT, dm = (V+OUT − V−OUT)
where V+OUT and V−OUT refer to the voltages at the +OUT and
−OUT terminals with respect to a common ground reference.
Similarly, the differential input voltage is defined as
Balance
Output balance is a measure of how close the output differential
signals are to being equal in amplitude and opposite in phase.
Output balance is most easily determined by placing a wellmatched resistor divider between the differential voltage nodes
and comparing the magnitude of the signal at the divider midpoint
with the magnitude of the differential signal (see Figure 52). By
this definition, output balance is the magnitude of the output
common-mode voltage divided by the magnitude of the output
differential mode voltage.
Output Balance Error 
VIN, dm = (+DIN − (−DIN))
Rev. E | Page 18 of 27
VOUT , cm
VOUT , dm
Data Sheet
ADA4932-1/ADA4932-2
THEORY OF OPERATION
The ADA4932-1/ADA4932-2 differ from conventional op amps
in that it has two outputs whose voltages move in opposite
directions and an additional input, VOCM. Like an op amp, it relies
on high open-loop gain and negative feedback to force these
outputs to the desired voltages. The ADA4932-1/ADA4932-2
behave much like standard voltage feedback op amps and
facilitates single-ended-to-differential conversions, commonmode level shifting, and amplifications of differential signals.
Like an op amp, the ADA4932-1/ADA4932-2 have high input
impedance and low output impedance. Because they use voltage
feedback, the ADA4932-1/ADA4932-2 manifest a nominally
constant gain bandwidth product.
Two feedback loops are employed to control the differential and
common-mode output voltages. The differential feedback, set
with external resistors, controls only the differential output voltage.
The common-mode feedback controls only the common-mode
output voltage. This architecture makes it easy to set the output
common-mode level to any arbitrary value within the specified
limits. The output common-mode voltage is forced, by the internal
common-mode feedback loop, to be equal to the voltage applied
to the VOCM input.
The internal common-mode feedback loop produces outputs
that are highly balanced over a wide frequency range without
requiring tightly matched external components. This results in
differential outputs that are very close to the ideal of being
identical in amplitude and are exactly 180° apart in phase.
Rev. E | Page 19 of 27
ADA4932-1/ADA4932-2
Data Sheet
APPLICATIONS INFORMATION
ANALYZING AN APPLICATION CIRCUIT
The ADA4932-1/ADA4932-2 use high open-loop gain and
negative feedback to force their differential and common-mode
output voltages in such a way as to minimize the differential
and common-mode error voltages. The differential error
voltage is defined as the voltage between the differential inputs
labeled +IN and −IN (see Figure 54). For most purposes, this
voltage is zero. Similarly, the difference between the actual
output common-mode voltage and the voltage applied to VOCM
is also zero. Starting from these principles, any application circuit
can be analyzed.
SETTING THE CLOSED-LOOP GAIN
Using the approach described in the Analyzing an Application
Circuit section, the differential gain of the circuit in Figure 54
can be determined by
V IN , dm
VnRG1
RG1
VnRF1
RF1
inIN+
+
R
 F
RG
inIN–
VnIN ADA4932-1/
ADA4932-2
This presumes that the input resistors (RG) and feedback resistors
(RF) on each side are equal.
VnOD
VOCM
VnRG2
ESTIMATING THE OUTPUT NOISE VOLTAGE
RG2
RF2
VnCM
VnRF2
07752-047
VOUT , dm
input, and the noise currents, inIN− and inIN+, appear between
each input and ground. The output voltage due to vnIN is obtained
by multiplying vnIN by the noise gain, GN (defined in the GN
equation that follows). The noise currents are uncorrelated with
the same mean-square value, and each produces an output voltage
that is equal to the noise current multiplied by the associated
feedback resistance. The noise voltage density at the VOCM/VOCMx
pin is vnCM. When the feedback networks have the same feedback
factor, as is true in most cases, the output noise due to vnCM is
common mode. Each of the four resistors contributes (4kTRxx)1/2.
The noise from the feedback resistors appears directly at the output,
and the noise from the gain resistors appears at the output multiplied by RF/RG. Table 11 summarizes the input noise sources, the
multiplication factors, and the output-referred noise density terms.
Figure 55. Noise Model
The differential output noise of the ADA4932-1/ADA4932-2
can be estimated using the noise model in Figure 55. The inputreferred noise voltage density, vnIN, is modeled as a differential
Table 11. Output Noise Voltage Density Calculations for Matched Feedback Networks
Input Noise Contribution
Differential Input
Inverting Input
Noninverting Input
VOCM Input
Gain Resistor, RG1
Gain Resistor, RG2
Feedback Resistor, RF1
Feedback Resistor, RF2
Input Noise Term
vnIN
inIN−
inIN+
vnCM
vnRG1
vnRG2
vnRF1
vnRF2
Input Noise
Voltage Density
vnIN
inIN− × (RF2)
inIN+ × (RF1)
vnCM
(4kTRG1)1/2
(4kTRG2)1/2
(4kTRF1)1/2
(4kTRF2)1/2
Output
Multiplication Factor
GN
1
1
0
RF1/RG1
RF2/RG2
1
1
Differential Output Noise
Voltage Density Term
vnO1 = GN(vnIN)
vnO2 = (inIN−)(RF2)
vnO3 = (inIN+)(RF1)
vnO4 = 0 V
vnO5 = (RF1/RG1)(4kTRG1)1/2
vnO6 = (RF2/RG2)(4kTRG2)1/2
vnO7 = (4kTRF1)1/2
vnO8 = (4kTRF2)1/2
Table 12. Differential Input, DC-Coupled
Nominal Gain (dB)
0
6
10
RF (Ω)
499
499
768
RG (Ω)
499
249
243
RIN, dm (Ω)
998
498
486
Differential Output Noise Density (nV/√Hz)
9.25
12.9
18.2
Table 13. Single-Ended Ground-Referenced Input, DC-Coupled, RS = 50 Ω
Nominal Gain (dB)
0
6
10
1
RF (Ω)
511
523
806
RG1 (Ω)
499
249
243
RT (Ω) (Std 1%)
53.6
57.6
57.6
RIN, cm (Ω)
665
374
392
RG2 (Ω)1
525
276
270
RG2 = RG1 + (RS||RT).
Rev. E | Page 20 of 27
Differential Output Noise Density (nV/√Hz)
9.19
12.6
17.7
Data Sheet
ADA4932-1/ADA4932-2
where:
β1 
2
β1  β2 
is the circuit noise gain.
RG1
RG2
and β2 
are the feedback factors.
RF1  RG1
RF2  RG2
When the feedback factors are matched, RF1/RG1 = RF2/RG2, β1 =
β2 = β, and the noise gain becomes
GN 
1
R
1 F
β
RG
Note that the output noise from VOCM goes to zero in this case.
The total differential output noise density, vnOD, is the root-sumsquare of the individual output noise terms.
v nOD 
As a practical summarization of the above issues, resistors of 1%
tolerance produce a worst-case input CMRR of approximately
40 dB, a worst-case differential-mode output offset of 25 mV
due to a 2.5 V VOCM input, negligible VOCM noise contribution,
and no significant degradation in output balance error.
CALCULATING THE INPUT IMPEDANCE FOR AN
APPLICATION CIRCUIT
The effective input impedance of a circuit depends on whether
the amplifier is being driven by a single-ended or differential
signal source. For balanced differential input signals, as shown
in Figure 56, the input impedance (RIN, dm) between the inputs
(+DIN and −DIN) is RIN, dm = RG + RG = 2 × RG.
RF
+VS
8
2
 vnOi
+DIN
RG
i 1
IMPACT OF MISMATCHES IN THE FEEDBACK
NETWORKS
VOUT, dm
ADA4932-2
–DIN
Table 12 and Table 13 list several common gain settings,
associated resistor values, input impedance, and output noise
density for both balanced and unbalanced input configurations.
+IN
VOCM ADA4932-1/
RG
–IN
–VS
RF
Figure 56. ADA4932-1/ADA4932-2 Configured for Balanced (Differential) Inputs
As previously mentioned, even if the external feedback networks
(RF/RG) are mismatched, the internal common-mode feedback
loop still forces the outputs to remain balanced. The amplitudes
of the signals at each output remain equal and 180° out of phase.
The input-to-output differential mode gain varies proportionately
to the feedback mismatch, but the output balance is unaffected.
For an unbalanced, single-ended input signal (see Figure 57),
the input impedance is
R IN , se




RG

 

RF

1
 2  R G  R F  
RF
The gain from the VOCM/VOCMx pin to VOUT, dm is equal to
2(β1 − β2)/(β1 + β2)
+VS
RIN, se
When β1 = β2, this term goes to zero and there is no differential
output voltage due to the voltage on the VOCM input (including
noise). The extreme case occurs when one loop is open and the
other has 100% feedback; in this case, the gain from VOCM input
to VOUT, dm is either +2 or −2, depending on which loop is closed.
The feedback loops are nominally matched to within 1% in
most applications, and the output noise and offsets due to the
VOCM input are negligible. If the loops are intentionally mismatched
by a large amount, it is necessary to include the gain term from
VOCM to VOUT, dm and account for the extra noise. For example, if
β1 = 0.5 and β2 = 0.25, the gain from VOCM to VOUT, dm is 0.67. If
the VOCM/VOCMx pin is set to 2.5 V, a differential offset voltage is
present at the output of (2.5 V)(0.67) = 1.67 V. The differential
output noise contribution is (9.6 nV/√Hz)(0.67) = 6.4 nV/√Hz.
Both of these results are undesirable in most applications;
therefore, it is best to use nominally matched feedback factors.
Mismatched feedback networks also result in a degradation of
the ability of the circuit to reject input common-mode signals,
RG
VOCM
RG
ADA4932-1/
ADA4932-2
–VS
RF
RL
VOUT, dm
07752-049
GN 
much the same as for a four-resistor difference amplifier made
from a conventional op amp.
07752-048
Similar to the case of a conventional op amp, the output noise
voltage densities can be estimated by multiplying the inputreferred terms at +IN and −IN by the appropriate output factor,
Figure 57. The ADA4932-1/ADA4932-2 with Unbalanced (Single-Ended) Input
The input impedance of the circuit is effectively higher than it is
for a conventional op amp connected as an inverter because a
fraction of the differential output voltage appears at the inputs
as a common-mode signal, partially bootstrapping the voltage
across the input resistor, RG. The common-mode voltage at the
amplifier input terminals can be easily determined by noting that
the voltage at the inverting input is equal to the noninverting
output voltage divided down by the voltage divider that is formed
by RF and RG in the lower loop. This voltage is present at both
input terminals due to negative voltage feedback and is in phase
Rev. E | Page 21 of 27
ADA4932-1/ADA4932-2
Data Sheet
Terminating a Single-Ended Input
This section describes how to properly terminate a single-ended
input to the ADA4932-1/ADA4932-2 with a gain of 1, RF = 499 Ω,
and RG = 499 Ω. An example using an input source with a
terminated output voltage of 1 V p-p and source resistance of 50 Ω
illustrates the four steps that must be followed. Note that
because the terminated output voltage of the source is 1 V p-p,
the open-circuit output voltage of the source is 2 V p-p. The
source shown in Figure 58 indicates this open-circuit voltage.
RS
VS
2V p-p
RTH
50Ω
RT
53.6Ω
Figure 60. Calculating the Thevenin Equivalent
Calculate the input impedance by using the following
formula:


 


 
R
499
  665 Ω



G
R IN , se  

 
499
RF

 1
  1
2
(
499
499
)



 2  (R G  R F )  
RTS = RTH = RS||RT = 25.9 Ω. Note that VTH is greater than
1 V p-p, which was obtained with RT = 50 Ω. The modified
circuit with the Thevenin equivalent (closest 1% value used for
RTH) of the terminated source and RTS in the lower feedback
loop is shown in Figure 61.
RF
499Ω
+VS
RF
499Ω
RIN, se
665Ω
RS
+VS
VTH
1.03V p-p
RG
50Ω
VS
2V p-p
RG
ADA4932-1/
ADA4932-2
VOCM
RTS
25.5Ω
RL VOUT, dm
499Ω
07752-050
499Ω
Figure 61 presents a tractable circuit with matched
feedback loops that can be easily evaluated.
To match the 50 Ω source resistance, calculate the
termination resistor, RT, using RT||665 Ω = 50 Ω. The
closest standard 1% value for RT is 53.6 Ω.
RF
499Ω
+VS
RS
RG
499Ω
RT
53.6Ω
VOCM
RG
499Ω
Figure 61. Thevenin Equivalent and Matched Gain Resistors
Figure 58. Calculating Single-Ended Input Impedance, RIN
50Ω
RL VOUT, dm
–VS
–VS
RIN, se
50Ω
ADA4932-1/
ADA4932-2
RF
RF
ADA4932-1/
ADA4932-2
RL
VOUT, dm
499Ω
–VS
RF
499Ω
07752-051
VS
2V p-p
RG
499Ω
RG
499Ω
2.
RTH
25.5Ω
499Ω
VOCM
VTH
1.03V p-p
25.9Ω
07752-053
1.
Figure 59 shows that the effective RG in the upper feedback
loop is now greater than the RG in the lower loop due to the
addition of the termination resistors. To compensate for the
imbalance of the gain resistors, add a correction resistor (RTS)
in series with RG in the lower loop. RTS is the Thevenin
equivalent of the source resistance, RS, and the termination
resistance, RT, and is equal to RS||RT.
07752-052
3.
with the input signal, thus reducing the effective voltage across
RG in the upper loop and partially bootstrapping RG.
Figure 59. Adding Termination Resistor, RT
Rev. E | Page 22 of 27
It is useful to point out two effects that occur with a
terminated input. The first is that the value of RG is increased
in both loops, lowering the overall closed-loop gain. The
second is that VTH is a little larger than 1 V p-p, as it would
be if RT = 50 Ω. These two effects have opposite impacts on
the output voltage, and for large resistor values in the feedback
loops (~1 kΩ), the effects essentially cancel each other out.
For small RF and RG, or high gains, however, the diminished
closed-loop gain is not canceled completely by the increased
VTH. This can be seen by evaluating Figure 61.
The desired differential output in this example is 1 V p-p
because the terminated input signal was 1 V p-p and the
closed-loop gain = 1. The actual differential output voltage,
however, is equal to (1.03 V p-p)(499/524.5) = 0.98 V p-p.
To obtain the desired output voltage of 1 V p-p, a final gain
adjustment can be made by increasing RF without modifying
any of the input circuitry (see Step 4).
Data Sheet
4.
ADA4932-1/ADA4932-2
The feedback resistor value is modified as a final gain
adjustment to obtain the desired output voltage.
SETTING THE OUTPUT COMMON-MODE VOLTAGE
To make the output voltage VOUT = 1 V p-p, calculate RF by
using the following formula:
RF 
Desired V
OUT ,dm
R
VTH
1 V p  p524.5 
1.03 V p  p
G
 RTS 

 509 
The closest standard 1% value to 509 Ω is 511 Ω, which
gives a differential output voltage of 1.00 V p-p.
In cases where more accurate control of the output commonmode level is required, it is recommended that an external
source or resistor divider be used with source resistance less
than 100 Ω. If an external voltage divider consisting of equal
resistor values is used to set VOCM to midsupply with greater
accuracy than produced internally, higher values can be used
because the external resistors are placed in parallel with the
internal resistors. The output common-mode offset listed in the
Specifications section assumes that the VOCM input is driven by a
low impedance voltage source.
The final circuit is shown in Figure 62.
RF
511Ω
+VS
1V p-p
RS
VS
2V p-p
50Ω
RG
RT
53.6Ω
499Ω
VOCM
RG
RTS
25.5Ω
ADA4932-1/
ADA4932-2
RL
VOUT, dm
1.00V p-p
499Ω
07752-054
–VS
RF
511Ω
The VOCM/VOCMx pin of the ADA4932-1/ADA4932-2 is internally
biased with a voltage divider comprised of two 50 kΩ resistors
across the supplies, with a tap at a voltage approximately equal
to the midsupply point, [(+VS) + (−VS)]/2. Because of this
internal divider, the VOCM/VOCMx pin sources and sinks current,
depending on the externally applied voltage and its associated
source resistance. Relying on the internal bias results in an
output common-mode voltage that is within about 100 mV of
the expected value.
Figure 62. Terminated Single-Ended-to-Differential System with G = 2
INPUT COMMON-MODE VOLTAGE RANGE
The ADA4932-1/ADA4932-2 input common-mode range is
shifted down by approximately one VBE, in contrast to other
ADC drivers with centered input ranges such as the ADA4939-1/
ADA4939-2. The downward-shifted input common-mode
range is especially suited to dc-coupled, single-ended-todifferential, and single-supply applications.
For ±5 V operation, the input common-mode range at the
summing nodes of the amplifier is specified as −4.8 V to +3.2 V,
and is specified as +0.2 V to +3.2 V with a +5 V supply. To
avoid nonlinearities, the voltage swing at the +IN and −IN
terminals must be confined to these ranges.
INPUT AND OUTPUT CAPACITIVE AC COUPLING
While the ADA4932-1/ADA4932-2 is best suited to dc-coupled
applications, it is nonetheless possible to use it in ac-coupled
circuits. Input ac coupling capacitors can be inserted between
the source and RG. This ac coupling blocks the flow of the dc
common-mode feedback current and causes the ADA4932-1/
ADA4932-2 dc input common-mode voltage to equal the dc
output common-mode voltage. These ac coupling capacitors must
be placed in both loops to keep the feedback factors matched.
Output ac coupling capacitors can be placed in series between
each output and its respective load.
It is also possible to connect the VOCM input to a common-mode
level (CML) output of an ADC; however, care must be taken to
ensure that the output has sufficient drive capability. The input
impedance of the VOCM/VOCMx pin is approximately 25 kΩ. If
multiple ADA4932-1/ADA4932-2 devices share one ADC
reference output, a buffer may be necessary to drive the parallel
inputs.
HIGH PERFORMANCE PRECISION ADC DRIVER
Using a differential amplifier to drive an ADC successfully is
linked to balancing each side of the differential amplifier
correctly. Figure 64 shows the schematic for the ADA4932-1,
AD7626, and associated circuitry. In the test circuit used, a
2.4 MHz band-pass filter follows the signal source. The bandpass filter eliminates harmonics of the 2.4 MHz signal and
ensures that only the frequency of interest is passed and
processed by the ADA4932-1 and AD7626.
The ADA4932-1 is particularly useful when driving higher frequency inputs to the AD7626, a 10 MSPS ADC with a switched
capacitor input. The resistor (R8, R9) and capacitor (C5, C6)
circuit between the ADA4932-1 and AD7626 IN+ and IN− pins
acts as a low-pass filter to noise. The filter limits the input bandwidth to the AD7626, but its main function is to optimize the
interface between the driving amplifier and the AD7626. The
series resistor isolates the driver amplifier from high frequency
switching spikes from the ADC switched capacitor front end.
The AD7626 data sheet shows values of 20 Ω and 56 pF. In
Figure 64, these values were empirically optimized to 33 Ω and
56 pF. The resistor-capacitor combination can be optimized slightly
for the circuit and input frequency being converted by simply
varying the R-C combination; however, keep in mind that
having the incorrect combination limits the THD and linearity
performance of the AD7626. In addition, increasing the bandwidth
as seen by the ADC introduces more noise.
Rev. E | Page 23 of 27
Data Sheet
Another aspect of optimization is the selection of the power
supply voltages for the ADA4932-1. In the circuit, the output
common-mode voltage (VCM pin) of the AD7626 is 2.048 V
for the internal reference voltage of 4.096 V, and each input
(IN+, IN−) swings between 0 V and 4.096 V, 180° out of phase.
This provides an 8.2 V full-scale differential input to the ADC.
The ADA4932-1 output stage requires about 1.4 V headroom
with respect to each supply voltage for linear operation.
Optimum distortion performance is obtained when the supply
voltages are approximately symmetrical about the common-mode
voltage. If a negative supply of −2.5 V is chosen, then a positive
supply of at least +6.5 V is needed for symmetry about the
common-mode voltage of 2.048 V.
07752-064
ADA4932-1/ADA4932-2
FREQUENCY (MHz)
Experiments performed indicate that a positive supply of 7.25 V
gives the best overall distortion for a 2.4 MHz tone. Using a low
jitter clock source and a single tone −1 dBFS amplitude, 2.402 MHz
input to the AD7626 yielded the results shown in Figure 63 of
88.49 dB SNR and −86.17 dBc THD. At this input level, the ADC
limits the SFDR to 83.8 dB. As can be seen from the plot, the
harmonics of the fundamental alias back into the pass band.
For example, when sampling at 10 MSPS, the third harmonic
(7.206 MHz) is aliased into the pass band at 10.000 MHz –
7.206 MHz = 2.794 MHz.
Figure 63. AD7626 Output, 64,000 Point, FFT Plot −1 dBFS Amplitude
2.40173 MHz Input Ton, 10.000 MSPS Sampling Rate
The nonharmonic noise admitted through the pass band of the
band-pass filter used in the circuit is replaced by the average
noise across the Nyquist bandwidth when calculating the SNR
and THD. The performance of this or any high speed circuit is
highly dependent on proper PCB layout. This includes, but is
not limited to, power supply bypassing, controlled impedance
lines (where required), component placement, signal routing,
and power and ground planes. For a more detailed analysis of
this circuit, refer to Circuit Note CN-0105.
+5V
0.1µF
0.1µF
+2.048V
AD8031
+7.25V
6
7
8
+5V
FROM
50Ω
SIGNAL
SOURCE
R6
499Ω 1
2.4MHz
BPF
R3
499Ω
2
R2
53.6Ω
9
R1
53.6Ω
C1
2.2nF
R4
39Ω
+VS
–FB
11
+IN
–OUT
VOCM
R8
33Ω
3
R7
499Ω 4
+OUT
VCM
IN–
+FB
14
–2.5V
VDD1
VDD2
VIO
C5
56pF
10
R9
33Ω
C6
56pF
16 15
+2.5V
0.1µF
AD7626
–IN
–VS
+2.5V
0.1µF
+4.096V
TO 0V
ADA4932-1
0.1µF
R5
499Ω
0.1µF
IN+
GND
0V TO
+4.096V
PAD
13
0.1µF
Figure 64. ADA4932-1 Driving the AD7626 (All Connections and Decoupling Not Shown)
Rev. E | Page 24 of 27
07752-065
5
0.1µF
Data Sheet
ADA4932-1/ADA4932-2
HIGH PERFORMANCE ADC DRIVING
The ADA4932-1/ADA4932-2 are ideally suited for broadband
dc-coupled applications. The circuit in Figure 65 shows a frontend connection for an ADA4932-1 driving an AD9245, a 14-bit,
20 MSPS/40 MSPS/65 MSPS/80 MSPS ADC, with dc coupling
on the ADA4932-1 input and output. (The AD9245 achieves
its optimum performance when driven differentially.) The
ADA4932-1 eliminates the need for a transformer to drive the
ADC and performs a single-ended-to-differential conversion and
buffering of the driving signal.
Because the inputs are dc-coupled, dc common-mode current
flows in the feedback loops, and a nominal dc level of 0.84 V is
present at the amplifier input terminals. A fraction of the output
signal is also present at the input terminals as a common-mode
signal; its level is equal to the ac output swing at the noninverting
output, divided down by the feedback factor of the lower loop.
In this example, this ripple is 0.5 V p-p × [524.5/(524.5 + 511)] =
0.25 V p-p. This ac signal is riding on the 0.84 V dc level, producing a voltage swing between 0.72 V and 0.97 V at the input
terminals. This is well within the specified limits of 0.2 V to 1.5 V.
The ADA4932-1 is configured with a single 3.3 V supply and a
gain of 1 for a single-ended input to differential output. The
53.6 Ω termination resistor, in parallel with the single-ended
input impedance of approximately 665 Ω, provides a 50 Ω
termination for the source. The additional 25.5 Ω (524.5 Ω
total) at the inverting input balances the parallel impedance
of the 50 Ω source and the termination resistor driving the
noninverting input.
With an output common-mode voltage of 1.65 V, each ADA4932-1
output swings between 1.4 V and 1.9 V, opposite in phase,
providing a gain of 1 and a 1 V p-p differential signal to the
ADC input. The differential RC section between the ADA4932-1
output and the ADC provides single-pole low-pass filtering and
extra buffering for the current spikes that are output from the
ADC input when its SHA capacitors are discharged.
In this example, the signal generator has a 1 V p-p symmetric,
ground-referenced bipolar output when terminated in 50 Ω.
The VOCM input is bypassed for noise reduction, and set externally
with 1% resistors to maximize output dynamic range on the
tight 3.3 V supply.
The AD9245 is configured for a 1 V p-p full-scale input by
connecting its SENSE pin to VREF, as shown in Figure 65.
511Ω
VOUT, dm = 1V p-p
VOUT, cm = 1.65V
3.3V
0.1µF
10kΩ
1%
50Ω
499Ω
2V p-p
SIGNAL
GENERATOR
0.1µF
33Ω
VOCM
53.6Ω
10kΩ
1%
0.1µF
ADA4932-1
AVDD
20pF
499Ω
33Ω
25.5Ω
VIN–
0.1µF
AD9245
VIN+ VREF SENSE AGND
10µF
+
511Ω
Figure 65. ADA4932-1 Driving an AD9245 ADC with DC-Coupled Input and Output
Rev. E | Page 25 of 27
07752-270
1V p-p CENTERED
AT GROUND
ADA4932-1/ADA4932-2
Data Sheet
LAYOUT, GROUNDING, AND BYPASSING
As a high speed device, the ADA4932-1/ADA4932-2 are
sensitive to the PCB environment in which it operates.
Realizing its superior performance requires attention to the
details of high speed PCB design.
Bypass the power supply pins as close to the device as possible
and directly to a nearby ground plane. Use high frequency ceramic
chip capacitors. It is recommended to use two parallel bypass
capacitors (1000 pF and 0.1 μF) for each supply. Place the 1000
pF capacitor closer to the device. Further away, provide low
frequency bulk bypassing using 10 μF tantalum capacitors from
each supply to ground.
The first requirement is a solid ground plane that covers as much
of the board area around the ADA4932-1/ADA4932-2 as
possible. However, the area near the feedback resistors (RF), gain
resistors (RG), and clear the input summing nodes (Pin 2 and
Pin 3) of all ground and power planes (see Figure 66). Clearing the
ground and power planes minimizes any stray capacitance at
these nodes and thus minimizes peaking of the response of the
amplifier at high frequencies.
Ensure that signal routing is short and direct to avoid parasitic
effects. Wherever complementary signals exist, provide a
symmetrical layout to maximize balanced performance. When
routing differential signals over a long distance, keep PCB
traces close together, and twist any differential wiring to
minimize loop area. Doing this reduces radiated energy and
makes the circuit less susceptible to interference.
The thermal resistance, θJA, is specified for the device, including
the exposed pad, soldered to a high thermal conductivity 4-layer
circuit board, as described in EIA/JESD51-7.
1.30
0.80
07752-055
07752-056
1.30 0.80
Figure 66. Ground and Power Plane Voiding in Vicinity of RF and RG
Figure 67. Recommended PCB Thermal Attach Pad Dimensions (Millimeters)
1.30
TOP METAL
GROUND PLANE
0.30
PLATED
VIA HOLE
07752-057
POWER PLANE
BOTTOM METAL
Figure 68. Cross-Section of 4-Layer PCB Showing Thermal Via Connection to Buried Ground Plane (Dimensions in Millimeters)
Rev. E | Page 26 of 27
Data Sheet
ADA4932-1/ADA4932-2
OUTLINE DIMENSIONS
3.10
3.00 SQ
2.90
PIN 1
INDICATOR
0.30
0.23
0.18
PIN 1
INDICATOR
16
13
0.50
BSC
1
12
EXPOSED
PAD
1.45
1.30 SQ
1.15
4
9
0.80
0.75
0.70
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
0.25 MIN
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
111808-A
TOP VIEW
5
8
0.50
0.40
0.30
COMPLIANT TO JEDEC STANDARDS MO-220-WEED.
Figure 69. 16-Lead Lead Frame Chip Scale Package [LFCSP]
3 mm × 3 mm Body and 0.75 mm Package Height
(CP-16-21)
Dimensions shown in millimeters
4.10
4.00 SQ
3.90
PIN 1
INDICATOR
0.50
BSC
PIN 1
INDICATOR
24
19
18
1
2.40
2.30 SQ
2.20
EXPOSED
PAD
6
13
0.80
0.75
0.70
SEATING
PLANE
0.50
0.40
0.30
12
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.203 REF
0.30
0.25
0.20
7
BOTTOM VIEW
0.20 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WGGD-8.
01-18-2012-A
TOP VIEW
Figure 70. 24-Lead Lead Frame Chip Scale Package [LFCSP]
4 mm × 4 mm Body and 0.75 mm Package Height
(CP-24-14)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
ADA4932-1YCPZ-R2
ADA4932-1YCPZ-RL
ADA4932-1YCPZ-R7
ADA4932-2YCPZ-R2
ADA4932-2YCPZ-RL
ADA4932-2YCPZ-R7
1
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
16-Lead LFCSP
16-Lead LFCSP
16-Lead LFCSP
24-Lead LFCSP
24-Lead LFCSP
24-Lead LFCSP
Z = RoHS Compliant Part.
©2008–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07752-0-5/16(E)
Rev. E | Page 27 of 27
Package Option
CP-16-21
CP-16-21
CP-16-21
CP-24-14
CP-24-14
CP-24-14
Ordering Quantity
250
5,000
1,500
250
5,000
1,500
Branding
H1K
H1K
H1K