Digital CCD Camera Head Amplifier CXA3796N Description The CXA3796N is a bipolar IC developed as a head amplifier for digital CCD cameras. This IC provides the following functions: correlated double sampling, AGC for the CCD signal, A/D sample and hold, blanking, A/D reference voltage, and an output driver. (Applications: CCD cameras) Features High sensitivity made possible by a high-gain AGC amplifier Blanking function provided for the purpose of calibrating the CCD output signal black level Regulator output pin provided for A/D converter reference voltage Built-in sample-and-hold circuits for camera signals required by external A/D converters <Changes and improvements from CXA2096N> Selectable maximum gain of AGC amplifier (MAXGAIN mode) Minus gain setting of AGC amplifier (GAINSHIFT mode) CCDLEVEL output blanking function Input dynamic range expansion Noise characteristics improvement Package 24-pin SSOP (Plastic) Structure Bipolar silicon monolithic IC Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. -1- E07Z39-CR CXA3796N Absolute Maximum Ratings Supply voltage VCC 5.5 V Operating temperature Topr –20 to +75 °C Storage temperature Tstg –65 to +150 °C Allowable power dissipation PD 417 mW 3.0 to 3.6 V Operating Conditions Supply voltage VCC1, 2, 3 -2- CXA3796N ICONT VCC2 DIN PIN CLPDM GND1 SHD SHP VCC1 CCDLEVEL AGCCONT AGCCLP Block Diagram and Pin Configuration 24 23 22 21 20 19 18 17 16 15 14 13 BUF SH1 SH2 DC SHIFT AGC OB SW SH3 AGC CLP DMSW2 CDS CLP2 VREF CAM SH DMSW1 CDS CLP1 VRT DRV OFFSET VRT VRB DRV BLK SW VRB DRVOUT VCC3 8 9 10 11 12 CLPOB GND3 7 XRS GAINSHIFT 6 PBLK 5 OFFSET 4 VRT 3 VRB 2 MAXGAIN 1 GND2 DRV -3- CXA3796N Pin Description (VCC1, 2, 3 = 3.3V) Pin No. Symbol 1 GND2 3 GND3 19 GND1 2 GAINSHIFT I/O Pin voltage — GND Gain shifted according to the following setting. I VCC to 0.7VCC: 0dB OPEN: –3dB 0.3VCC to GND: –6dB Equivalent circuit Description Ground. 11µA 1k 120k 80k 40k 2k 2 2.2V 40k 120k 7p 1k IOFFSET Gain shift. 80k 27.5µA 220µA 11µA 40k 27.5µA 0 to 55µA Driver output for A/D converter capable of direct DC coupling capacitor. 2k VRB = 1.485V 4 DRVOUT 55µA 55µA O VRB to VRB + 110mV ICONT 3.52 to 7.04mA Dynamic range = 1.07Vp-p. 2k 4 CAM signal 6 5 VCC3 16 VCC1 23 VCC2 6 MAXGAIN — VCC VCC to 0.7VCC: 34dB OPEN: 26dB I 0.3VCC to GND: 30dB * AGCCONT = 3.0V Power supply. 11µA 1k 120k 80k 40k 2k 6 2.2V 40k 120k 7p 1k -4- 80k 11µA 40k MAXGAIN. CXA3796N Pin No. Symbol I/O Pin voltage Equivalent circuit 100 Description 1.485V regulator output. 1k 200 16.5k 7 VRB O 1.485V (0.45VCC) 300 300 7 1.485V 1.3k 13.5k 110µA 4k 12 Be sure to decouple this pin near the IC pins to prevent the oscillation and external noise when this pin is not used. (Recommended capacitor value: 4.7μF) 2.585V regulator output. 16k 1k 12 6.5k 8 VRT O 2.585V (0.783VCC) 300 300 2.58V 8 23.5k 200 55µ 1k 50k 220µ 55µ 50k 200 1k Controls the output offset. 2k 60k 1.65V 9 OFFSET I 1.65 to 3.3V & 0V 1.5k VRB 3k 24k 55µA 60k 55µA 2k 9 10 PBLK 60k When 0V (preset mode): VRB + 40mV Camera signal preblanking pulse input. 1k 60k 2k I When 3.3V: VRB + 0mV When 1.65V: VRB + 110mV 1k 55µA VTH = 1.65V Be sure to decouple this pin near the IC pins to prevent the oscillation and external noise when this pin is not used. (Recommended capacitor value: 4.7μF) 10 1.65V Active: Low 60k 27.5µA 50µA VTH = 0.74V Active when Low. Calibrates the black level of the AGC output waveform. When PBLK is Low, the DRVOUT potential is forced to VRB. 440µA 1k 24k 11 XRS 145 I 11 Sampling 0.74V 7k 98µA -5- 1k Camera signal sampleand-hold pulse input. CXA3796N Pin No. Symbol I/O Pin voltage Equivalent circuit 12 CLPOB 1k 16k VTH = 1.65V Description 60k 12 Clamp pulse input used to clamp the optical black portion of the camera signal after it passes through the AGC amplifier. 13 AGC clamp capacitor. (Recommended value: 0.1μF) 2k I 1.65V Active: Low 60k 55µA 1k 5k 5k 145 13 AGCCLP O Approximately1.4V 145 1k 50k 1.9V 1k 1k 1k 500 14 3.4k 3.4k 3.4k 3.18V I 500k 2.475V 220µA 14 AGCCONT 3.4k 220µA 1.65 to 3.3V (0.5VCC to 1.0VCC) 3k ICONT -6- 110µA 110µA 110µA 110µA 3k AGC gain control input. When 1.65V: –1 dB (Minimum gain) When 3.3V: 31.5 dB (Maximum gain) MAXGAIN = OPEN GAINSHIFT = VCC * Gain values can be changed by setting two pins shown above. CXA3796N Pin No. Symbol I/O Pin voltage Equivalent circuit Description 220µA 15 CCDLEVEL O CCD signal black level of DIN input Approximately2.5V 15 500 500 250 17 SHP I VTH = 0.74V Enables monitoring output of the SH3 output camera signal. 250 55µA Preset level sample-andhold pulse input. 440µA 1k 36k 145 17 Sampling 18 SHD 18 0.745V 10.5k I VTH = 1.65V Data level sample-andhold pulse input. 1k 1k 60k 1k 2k 20 CLPDM 1.65V I 20 Active: Low Clamp pulse input used to clamp the dummy pixel portion of the input CCD signal. 60k 55µA 500 500 1k 145 21 PIN 22 DIN Black level Approximately2.5V I 11µA 21 49k 22 1k 1.65 to 3.3V 22k 1k 11k 1k 27.5µA DRVOUT output waveform rise time control input. 1k 15k I CCD signal input. 145 330µA 24 ICONT 500 11µA 2k 2.475V 24 6k 6k 45k 110µA -7- When 1.65V: Maximum rise time When 3.3V: Minimum rise time CXA3796N Electrical Characteristics (Ta = 25°C, VCC1, 2, 3 = 3.3V) Item Symbol Min. Typ. Max. Unit IDC VAGCCONT = 1.65V, open between VRT and VRB 33 MAXGAIN = OPEN, GAINSHIFT = VCC ICONT = 3.3V, SHP, SHD = Duty75% (H:L = 3:1) VCC = 3.0V IDC30 VAGCCONT = 1.5V, open between VRT and VRB 29.5 41.3 MAXGAIN = OPEN, GAINSHIFT = VCC ICONT = 3.0V, SHP, SHD = Duty75% (H:L = 3:1) MAXGAIN1 DIN = 1μs, 15 mVp-p pulse A CONT max.1 VAGCCONT = 3.0V, ICONT = 3.3V MAXGAIN = VCC, GAINSHIFT = VCC 31 34 37 MAXGAIN2 DIN = 1μs, 20 mVp-p pulse A CONT max.2 VAGCCONT = 3.0V, ICONT = 3.3V MAXGAIN = GND, GAINSHIFT = VCC 27 30 33 MAXGAIN3 DIN = 1μs, 30 mVp-p pulse A CONT max.3 VAGCCONT = 3.0V, ICONT = 3.3V MAXGAIN = OPEN, GAINSHIFT = VCC 23 26 29 DIN = 1μs, 500 mVp-p pulse GAINSHIFT1 A CONT min.1 VAGCCONT = 1.65V, ICONT = 3.3V MAXGAIN = OPEN, GAINSHIFT = VCC — –0.8 1.4 DIN = 1μs, 500 mVp-p pulse GAINSHIFT2 A CONT min.2 VAGCCONT = 1.65V, ICONT = 3.3V MAXGAIN = OPEN, GAINSHIFT = OPEN — –3.6 DIN = 1μs, 500 mVp-p pulse GAINSHIFT3 A CONT min.3 VAGCCONT = 1.65V, ICONT = 3.3V MAXGAIN = OPEN, GAINSHIFT = GND — –6.5 –3.5 VCC = 3.3V Current consumption AGC Conditions 45.7 65.6 mA 59 –1 Gain variable AGC G1 width 1 A CONT max.1 – A CONT min.1 29.6 34.8 — Gain variable AGC G2 width 2 A CONT max.2 – A CONT min.1 25.6 30.8 — Gain variable AGC G3 width 3 A CONT max.3 – A CONT min.1 21.6 26.8 — Gain variable AGC G4 width 4 A CONT max.1 – A CONT min.2 32 37.6 — Gain variable AGC G5 width 5 A CONT max.2 – A CONT min.2 28 33.6 — Gain variable AGC G6 width 6 A CONT max.3 – A CONT min.2 24 29.6 — Gain variable AGC G7 width 7 A CONT max.1 – A CONT min.3 34.5 40.5 — Gain variable AGC G8 width 8 A CONT max.2 – A CONT min.3 30.5 36.5 — Gain variable AGC G9 width 9 A CONT max.3 – A CONT min.3 26.5 32.5 — -8- dB CXA3796N Item Symbol REF Min. Typ. Max. Unit Dynamic range Max. AGCmax.D VAGCCONT = 3.3V MAXGAIN = OPEN, GAINSHIFT = VCC At the 0.88 1.07 level when DRVOUT output signal is saturated — V Dynamic range Typ. AGCtyp.D VAGCCONT = 2.2V MAXGAIN = OPEN, GAINSHIFT = VCC At the 0.88 1.07 level when DRVOUT output signal is saturated — V Offset High CAOF high OFFSET = 1.65V 88 115 — Offset Low CAOF low OFFSET = 3.3V — 3 10 Offset Preset CAOF pre OFFSET = 0V 30 41 55 VRTDC level VRTO 400Ωload 2535 2585 2635 VRBDC level VRBO 400Ωload 1435 1485 1535 mV AGC DRV Conditions mV VRT – VRB ΔVR 400Ωload 1045 1087 1155 BLK Offset BLKOF1 BLKOF (PBLK = 3.3V) – BLKOF (PBLK = 0V) ICONT = 3.3V –15 2 30 mV SH3 Dynamic range SH3 D DIN = 1μs, 1.1Vp-p pulse 0.9 1 — V -9- CXA3796N Electrical Characteristics Measurement Circuit 24 23 21 19 20 18 17 16 C3 0.1µF 15 14 AGCCLP AGCCONT VCC1 SHP SHD GND1 DIN 22 V3 1.65 to 3.3V PL3 VCC1 3.3V C2 1µF CLPDM C1 1µF VCC2 ICONT VCC2 3.3V PL2 PL1 CCDLEVEL AC V2 PIN V1 1.65 to 3.3V 13 BUF SH1 SH2 DC SHIFT AGC OB SW SH3 AGC CLP DMSW2 CDS CLP2 VREF CAM SH DMSW1 CDS CLP1 VRT DRV OFFSET VRT VRB DRV BLK SW VRB DRV V6 3.3V V5 2.03V OPEN OPEN R3 10k C5 4.7µ C4 4.7µ 12 CLPOB V4 0 to 3.3V 11 XRS R1 400 10 PBLK 9 SW2 SW2 H L 8 OFFSET VCC3 3.3V R2 22 7 VRT 6 VRB 5 VCC3 GND3 GND2 SW1 H L 4 MAXGAIN 3 DRVOUT 2 GAINSHIFT 1 PL6 PL5 PL4 V7 3.3V C6 40pF GND SW1 H OPEN L GAINSHIFT 0dB mode –3dB mode –6dB mode SW2 H OPEN L MAXGAIN 34dB (VAGCCONT = 3.0V) 26dB (VAGCCONT = 3.0V) 30dB (VAGCCONT = 3.0V) - 10 - CXA3796N Measurement Timing Chart 1H 2µs 2.5V PL4 (CLPOB) GND 1H 2µs 2.5V PL1 (CLPDM) GND 2.5V PL6 (PBLK) GND 1H V2 (DIN) Different for each test Equivalent to CCD signal black level 2.5V PL2 (SHD) PL3 (SHP) PL5 (XRS) GND - 11 - CXA3796N Application Circuit CCD 24 23 22 21 20 19 18 17 16 0.1µF 15 14 AGCCLP AGCCONT CCDLEVEL SHD GND1 PIN CLPDM 1µF DIN VCC2 ICONT 1µF VAGCCONT 1.65 to 3.3V SHP VCC SHD VCC1 CLPDM SHP VCC VICONT 1.65 to 3.3V 13 BUF SH1 SH2 DC SHIFT AGC OB SW SH3 AGC CLP DMSW2 CDS CLP2 VREF CAM SH DMSW1 CDS CLP1 VRT DRV OFFSET VRT VRB DRV BLK SW VRB DRV 12 PBLK XRS CLPOB 22 OPEN VCC OPEN 11 CLPOB 10 XRS 9 PBLK 8 OFFSET 7 VRT VCC3 GND3 6 VRB 5 MAXGAIN 4 DRVOUT 3 GAINSHIFT 2 GND2 1 3.3V A/D IN 3.3V VRB VRT GAINSHIFT 0dB mode –3dB mode –6dB mode GND 4.7µ A/D SW1 H OPEN L VOFFSET 0 to 3.3V 4.7µ SW2 H OPEN L MAXGAIN 34dB (VAGCCONT = 3.0V) 26dB (VAGCCONT = 3.0V) 30dB (VAGCCONT = 3.0V) Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. - 12 - CXA3796N Description of Operation Refer to the Block Diagram. Timing Chart (when VCC = 3.3 V) Signal interval OPB interval Idle transfer interval Signal interval Precharge level CCD output Signal level SHP SHD SH1 output 2.5V SH2 output [∗1] SH3 output [∗2] 2.5V CLPDM (2µ dummy bit portion during the idle transfer interval) 2µs AGC output SH3 output − SH2 output Basic black level Black level 0.715V × (–N) [∗3] XRS CLPOB (2µ during the OPB interval) 2µs CAMSH output 0.715V PBLK (10µ during the idle transfer interval) 10µs BLK SW output 1.485V [∗4] DRVOUT output [∗5] Approx. VRB + 40mV when OFFSET = 0V Approx. VRB + 110mV when OFFSET = 1.65V Approx. VRB when OFFSET = 3.3V - 13 - CXA3796N CDS (SH1, SH2, SH3): The CCD signal from the CCD image sensor is input to PIN and DIN where correlated double sampling (CDS) is performed by SH1, SH2 and SH3. The precharge level of the CCD output signal is sampled, held and output by the SH2 output, and the signal level is sampled, held and output by the SH3 output. SH1 and SH2 are the sample-and-hold circuits for the precharge level; SH3 is the sample-and-hold circuit for the signal level. CDSCLP 1, 2: CDSCLP1 and 2 stabilize the input signal DC level, clamp (CLPDM) the input signal during the idle transfer interval for the purpose of eliminating the AGC input offset, and adjust the DC level ([*1], [*2]) of SH2 and SH3 in line with VREF. CDSCLP1 is the clamp circuit for the precharge level, and CDSCLP2 is the clamp circuit for the signal level. AGC: AGC is the gain control amplifier for the camera signal. The gain can be varied from –1 to +31dB (when MAXGAIN = OPEN, GAINSHIFT = VCC) by adjusting the AGCCONT voltage control VAGCCONT from 1.65 to 3.3V. * Gain width can be changed by MAXGAIN = VCC/OPEN/GND, GAINSHIFT = VCC/OPEN/GND setting. CAM SH: CAM SH is the sample-and-hold circuit for synchronizing the data read-in timing for the external A/D. Sampling is possible according to the approximately 10ns sampling pulse width input to XRS. AGCCLP: The basic black level is set ([*3]) by clamping the AGC output waveform with the CLPOB clock during the OPB interval. When PBLK is High and CLPOB is Low, the clamping circuit operates, adjusting the AGCCLP current so that the DRVOUT potential equals the OFFSET potential (which is determined by the voltage applied to the OFFSET pin), thus setting the AGCCLP potential. The AGCCLP capacitance is connected to the AGCCLP pin. DC SHIFT: This circuit functions when AGCCLP operates, following the AGCCLP potential and forcing a DC shift of the AGC output waveform OPB interval to the basic black level. When AGCCLP is not operating, the basic black level is maintained at its previous setting. BLK SW: The black level is calibrated by blanking the black level signal of the AGC output waveform so that it does not fall below the basic black level and replacing the DC potential with VRB. ([*4]) The signal is blanked when PBLK is Low. OFFSET: OFFSET controls the DRV output waveform black level offset. The offset of the DRVOUT camera signals can be adjusted when a voltage is applied to OFFSET. ([*5]) The voltage controlled by OFFSET is output as the DRV output DC offset via AGCCLP, DCSHIFT, CAMSH and BLKSW. When the OFFSET voltage is 1.65 to 3.3V, DRVOUT DC can vary in a linear fashion from VRB + 110mV to VRB. In addition, when the OFFSET voltage is 0V, DRVOUT DC is preset to VRB + 40mV. DRV: DRV drives the external A/D. The current that flows to the last-stage amplifier in DRV is controlled by applying voltage to the ICONT pin, making it possible to adjust the rise time of the output waveform, which affects the external A/D load capacitance. The variable range is 1.65 to 3.3V, with 1.65V yielding the maximum and 3.3V yielding the minimum. The optimum rise time for the external A/D input capacitance can be selected. - 14 - CXA3796N VRT DRV, VRB DRV: These are the external A/D reference voltage drivers. These circuits are connected to A/D VRT and VRB, supplying 2.585V and 1.485V, respectively, when VCC is 3.3V. The IC's internal primary voltage is also generated on the basis of the VRT and VRB voltage. GAINSHIFT: AGC gain curve can be shifted by setting GAINSHIFT as follows. 0dB shift When applying VCC When OPEN –3dB shift When GND –6dB shift MAXGAIN: AGC MAX gain can be changed by setting MAXGAIN as follows. 34dB * when VAGCCOUNT = 3.0V When applying VCC When OPEN 26dB * when VAGCCOUNT = 3.0V When GND 30dB * when VAGCCOUNT = 3.0V CCDLEVEL BUF: This is buffer to monitor SH3 output camera signal and output from CCDLEVEL. SH3 output is output to CCDLEVEL when PBLK = High and internal generation voltage (Vref) is output when PBLK = Low. - 15 - CXA3796N Example of Representative Characteristics AGCCONT control supply voltage characteristics VAGCCONT vs. Gain 40 40 35 GAINSHIFT = VCC (0dB) MAXGAIN = VCC (34dB mode) GAINSHIFT = OPEN (−3dB) MAXGAIN = GND (30dB mode) 30 MAXGAIN = VCC (34dB mode) 30 MAXGAIN = GND (30dB mode) MAXGAIN = OPEN (26dB mode) MAXGAIN = OPEN (26dB mode) 25 Gain [dB] 25 Gain [dB] 35 20 15 20 15 10 10 5 5 0 0 −5 −5 0.5 0.6 0.7 0.8 VAGCCONT/VCC 0.9 1 0.9 1 40 35 30 GAINSHIFT = GND (−6dB) MAXGAIN = VCC (34dB mode) MAXGAIN = GND (30dB mode) MAXGAIN = OPEN (26dB mode) Gain [dB] 25 20 15 10 5 0 −5 −10 0.5 0.6 0.7 0.8 VAGCCONT/VCC - 16 - −10 0.5 0.6 0.7 0.8 VAGCCONT/VCC 0.9 1 CXA3796N AGCCONT control supply voltage characteristics VAGCCONT vs. Gain OFFSET control supply voltage characteristics VOFFSET vs. OFFSET 140 35 Tc = 27˚C 120 OFFSET [mV] 25 Gain [dB] Tc = 27˚C VCC = 3.0V VCC = 3.3V VCC = 3.6V 30 20 15 10 VCC = 3.0 VCC = 3.3 VCC = 3.6 100 80 60 40 5 20 0 −5 1.5 0 2 2.5 3 3.5 0 1 140 35 VCC = 3.3V −20˚C +27˚C +75˚C 20 15 10 100 80 60 40 5 20 0 −5 1.65 VCC = 3.3V Tc = −20˚C Tc = +27˚C Tc = +75˚C 120 OFFSET [mV] Gain [dB] 25 3 OFFSET control temperature characteristics VOFFSET vs. OFFSET AGCCONT control temperature characteristics AGCCONT vs. Gain 30 2 VOFFSET [V] VAGCCONT [V] 0 2.15 2.65 0 3.15 VAGCCONT [V] 1 2 VOFFSET [V] - 17 - 3 4 CXA3796N Maximum signal amplitude temperature characteristics (Max. gain) Tc vs. Vout Maximum signal amplitude temperature characteristics (Min. gain) Tc vs. Vout 1.4 1.4 VCC = 3.3V, AGCCONT = 3.3V Input amplitude DIN = 28mVpp Input amplitude DIN = 24mVpp Input amplitude DIN = 21mVpp 1.3 1.3 1.2 1.2 1 0.9 31.29dB DIN = 24mVpp +0 31.29 –0.16 dB 31.29dB DIN = 1250mVpp 1.1 VOUT [Vpp] 31.23dB DIN = 28mVpp +0 31.23 –0.18 dB 31.23dB 31.06dB 31.13dB 0.8 1 DIN = 1200mVpp DIN = 1100mVpp 0.9 DIN = 1000mVpp 0.8 31.35dB 0.7 31.35dB DIN = 21mVpp 31.17dB +0 31.235 –0.17 dB DIN = 800mVpp 0.7 DIN = 700mVpp 0.6 –20 0 30 0.6 –20 130 80 30 0 Tc [˚C] 80 Tc [˚C] VRT, VRB, VRT − VRB temperature characteristics Tc vs. VRT, VRB, VRT − VRB 2.8 VCC = 3.3V 2.6 VRT, VRB, VRT − VRB [V] VOUT [Vpp] 1.1 VCC = 3.3V, AGCCONT = 1.65V Input amplitude DIN = 700mVpp Input amplitude DIN = 800mVpp Input amplitude DIN = 1Vpp Input amplitude DIN = 1.1Vpp Input amplitude DIN = 1.2Vpp Input amplitude DIN = 1.25Vpp VRT 2.4 2.2 2 1.8 1.6 VRB 1.4 1.2 VRT – VRB 1 –40 –20 0 20 40 Tc [˚C] - 18 - 60 80 100 130 CXA3796N Package Outline (Unit: mm) 24PIN SSOP (PLASTIC) + 0.2 1.25 – 0.1 ∗7.8 ± 0.1 0.1 24 13 1 7.6 ± 0.2 ∗5.6 ± 0.1 A 12 b 0.13 M b = 0.22 ± 0.03 0.5 ± 0.2 0.1 ± 0.1 + 0.03 0.15 – 0.01 0.65 B DETAIL B : PALLADIUM 0˚ to 10˚ NOTE: Dimension "∗" does not include mold protrusion. DETAIL A PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN SONY CODE SSOP-24P-L01 LEAD TREATMENT PALLADIUM PLATING EIAJ CODE P-SSOP24-7.8x5.6-0.65 LEAD MATERIAL COPPER ALLOY PACKAGE MASS 0.1g JEDEC CODE - 19 - Sony Corporation