Marketing Bulletin DATE: May 6, 2005 TO: All Sales Personnel FROM: Mark Stoner RE: E11 (OS/03) Termination To all concerned parties, This bulletin is to notify all customers of the discontinuation of the following Ecliptek series effective May 1st, 2005: Series E11 Description 5V 14 pin DIP ECL Oscillator Recommended Replacement None In compliance with our End of Life (EOL) policy, this will serve as advanced notice of product termination. New orders will not be accepted after August 1st, 2005, with delivery to conclude by November 1st 2005. If there are any questions pertaining to this bulletin, please fell free to contact me. Thank you again for your cooperation. Best Regards, Mark W. Stoner Director of Marketing Ecliptek Corporation 3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234 STANDARD SPECIFICATIONS Frequency Range: Frequency Tolerance/Stability: 00 45 25 Operating Temperature Range Blank ET Storage Temperature Range Supply Voltage (VEE ) Input Current Output Voltage Logic High Output Voltage Logic Low Rise/Fall Time Duty Cycle Load Drive Capability Aging @ 25°C 6.000MHz to 155.520MHz (All Values Inclusive of Operating Temp. Range, Supply Voltage, and Load) ±100ppm Max. ±50ppm Max. ±25ppm Max. (0°C to +70°C only), (less than or equal to 125.000MHz only) OBSOLETE 0°C to +70°C -40°C to +85°C -55°C to +125°C -5.2Vdc ±5% (AA, AB, and AM); +5.2Vdc ±5% (AC) 140mA Maximum -1.0Vdc Min./-0.7Vdc Max. (AA, AB, and AM); 4.0Vdc Min./4.5Vdc M ax. (AC) -1.95Vdc Min./-1.60Vdc Max. (AA, AB, and AM); 3.00Vdc Min./3.42Vdc Max. (AC) 2nSec Maximum (Measured at 20% to 80% of waveform) 50% ±10% (Measured at 50% of waveform) 50 Ohms into -2.0Vdc (AA, AB, and AM); 50 Ohms into +3.0Vdc (AC) ±5ppm/year Maximum ENVIRONMENTAL & MECHANICAL Fine Leak Test: Gross Leak Test: Mechanical Shock: Vibration: Lead Integrity: MIL-STD-883, Method MIL-STD-883, Method MIL-STD-202, Method MIL-STD-883, Method MIL-STD-883, Method Solderability: Temperature Cycling: Resistance to Soldering Heat: Resistance to Solvents: 1014, Condition A 1014, Condition C 213, Condition C 2007, Condition A 2004 MIL-STD-883, Method 2002 MIL-STD-883, Method 1010 MIL-STD-202, Method 210 MIL-STD-202, Method 215 PIN CONFIGURATIONS PIN 1 7 8 14 AA Ground/Case -5.2V Output Ground AB No Connect or Complementary Output -5.2V Output Ground/Case AC No Connect or Complementary Output Ground/Case Output +5.2Vdc AM No Connect or Complementary Output Ground/Case Output -5.2Vdc PART NUMBERING GUIDE E11 00 AM ET C - 24.000M - CL175 Configuration Options CLXXX = Cut Leads (MAL01-101-000) G = Gull Wing (MAL01-001-000) Frequency Pin 1 Connection Blank = No Connect C = Complementary Output 15.240 ±0.203 1 0.9 MAX 7 7.620 ±0.203 Operating Temperature Range Blank = 0°C to +70°C ET = -40°C to +85°C Pin Configuration AA, AB, AC, or AM Per Pin Configuration Table Above Frequency Tolerance/Stability 00 = ±100ppm Maximum, 45 = ±50ppm Maximum 25 = ±25ppm Maximum ∅0.457 ±0.1 (X4) 8 14 5.08 MAX 13.2 MAX 5.08 MIN MARKING GUIDE 20.8 MAX (Line #1) ECLIPTEK ALL DIMENSIONS IN MILLIMETERS (Line #2) E11 AM C Pin 1 Connection Blank = No Connect C = Complementary Output Pin Configuration Per Pin Configuration Table Above (Line #3) XXX.XXXM Frequency (Line #4) XX Y ZZ ECLIPTEK E11AMC XXX.XXXM XXYZZ Week of Year Last Digit of Year Ecliptek Manufacturing Code (TEN02-001-000) SPECIFICATION CONTROL DRAWING Drawing Number CSC01-010-000 Title FULL SIZE ECL OSCILLATOR Revision Effectivity Date E 8675 NOTE: Pin 1 shall be marked with a black dot. Marking shall conform to conditions listed in TQC41-001-000. 08-27-03 ECN Number Approved By PAGE 1 OF 2 Date Released By Date