Features • • • • • • • • • • • High Performance, Low Power Atmel® AVR® 8-Bit Microcontroller Advanced RISC Architecture – 135 Powerful Instructions – Most Single Clock Cycle Execution – 32 × 8 General Purpose Working Registers – Fully Static Operation – Up to 16 MIPS Throughput at 16MHz – On-Chip 2-cycle Multiplier High Endurance Non-volatile Memory Segments – 64K/128K/256KBytes of In-System Self-Programmable Flash – 4Kbytes EEPROM – 8Kbytes Internal SRAM – Write/Erase Cycles:10,000 Flash/100,000 EEPROM – Data retention: 20 years at 85°C/ 100 years at 25°C – Optional Boot Code Section with Independent Lock Bits • In-System Programming by On-chip Boot Program • True Read-While-Write Operation – Programming Lock for Software Security • Endurance: Up to 64Kbytes Optional External Memory Space Atmel® QTouch® library support – Capacitive touch buttons, sliders and wheels – QTouch and QMatrix® acquisition – Up to 64 sense channels JTAG (IEEE std. 1149.1 compliant) Interface – Boundary-scan Capabilities According to the JTAG Standard – Extensive On-chip Debug Support – Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface Peripheral Features – Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode – Four 16-bit Timer/Counter with Separate Prescaler, Compare- and Capture Mode – Real Time Counter with Separate Oscillator – Four 8-bit PWM Channels – Six/Twelve PWM Channels with Programmable Resolution from 2 to 16 Bits (ATmega1281/2561, ATmega640/1280/2560) – Output Compare Modulator – 8/16-channel, 10-bit ADC (ATmega1281/2561, ATmega640/1280/2560) – Two/Four Programmable Serial USART (ATmega1281/2561, ATmega640/1280/2560) – Master/Slave SPI Serial Interface – Byte Oriented 2-wire Serial Interface – Programmable Watchdog Timer with Separate On-chip Oscillator – On-chip Analog Comparator – Interrupt and Wake-up on Pin Change Special Microcontroller Features – Power-on Reset and Programmable Brown-out Detection – Internal Calibrated Oscillator – External and Internal Interrupt Sources – Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby I/O and Packages – 54/86 Programmable I/O Lines (ATmega1281/2561, ATmega640/1280/2560) – 64-pad QFN/MLF, 64-lead TQFP (ATmega1281/2561) – 100-lead TQFP, 100-ball CBGA (ATmega640/1280/2560) – RoHS/Fully Green Temperature Range: – -40°C to 85°C Industrial Ultra-Low Power Consumption – Active Mode: 1MHz, 1.8V: 500µA – Power-down Mode: 0.1µA at 1.8V Speed Grade: – ATmega640V/ATmega1280V/ATmega1281V: • 0 - 4MHz @ 1.8V - 5.5V, 0 - 8MHz @ 2.7V - 5.5V – ATmega2560V/ATmega2561V: • 0 - 2MHz @ 1.8V - 5.5V, 0 - 8MHz @ 2.7V - 5.5V – ATmega640/ATmega1280/ATmega1281: • 0 - 8MHz @ 2.7V - 5.5V, 0 - 16MHz @ 4.5V - 5.5V – ATmega2560/ATmega2561: • 0 - 16MHz @ 4.5V - 5.5V 8-bit Atmel Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash ATmega640/V ATmega1280/V ATmega1281/V ATmega2560/V ATmega2561/V Summary 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 1. Pin Configurations 81 80 PA1 (AD1) 82 PA2 (AD2) 83 PJ7 84 PA0 (AD0) 85 GND 86 VCC 87 PK7 (ADC15/PCINT23) 88 PK5 (ADC13/PCINT21) 89 PK6 (ADC14/PCINT22) 90 PK3 (ADC11/PCINT19) 91 PK4 (ADC12/PCINT20) 92 PK1 (ADC9/PCINT17) 93 PK2 (ADC10/PCINT18) PK0 (ADC8/PCINT16) 94 PF7 (ADC7/TDI) 95 PF6 (ADC6/TDO) 96 PF4 (ADC4/TCK) 97 PF5 (ADC5/TMS) PF1 (ADC1) 98 PF2 (ADC2) PF0 (ADC0) 100 99 PF3 (ADC3) GND AREF TQFP-pinout ATmega640/1280/2560 AVCC Figure 1-1. 79 78 77 76 (OC0B) PG5 1 75 PA3 (AD3) (RXD0/PCINT8) PE0 2 74 PA4 (AD4) INDEX CORNER (TXD0) PE1 3 73 PA5 (AD5) (XCK0/AIN0) PE2 4 72 PA6 (AD6) (OC3A/AIN1) PE3 5 71 PA7 (AD7) (OC3B/INT4) PE4 6 70 PG2 (ALE) (OC3C/INT5) PE5 7 69 PJ6 (PCINT15) (T3/INT6) PE6 8 68 PJ5 (PCINT14) (CLKO/ICP3/INT7) PE7 9 67 PJ4 (PCINT13) VCC 10 66 PJ3 (PCINT12) GND 11 65 PJ2 (XCK3/PCINT11) (RXD2) PH0 12 64 PJ1 (TXD3/PCINT10) (TXD2) PH1 13 63 PJ0 (RXD3/PCINT9) (XCK2) PH2 14 62 GND (OC4A) PH3 15 61 VCC (OC4B) PH4 16 60 PC7 (A15) (OC4C) PH5 17 59 PC6 (A14) (OC2B) PH6 18 58 PC5 (A13) 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 (T1) PD6 31 (T0) PD7 30 (ICP1) PD4 29 (XCK1) PD5 28 (TXD1/INT3) PD3 27 (RXD1/INT2) PD2 26 (SDA/INT1) PD1 PG0 (WR) PL7 51 (SCL/INT0) PD0 25 PL6 (OC1B/PCINT6) PB6 (OC5C) PL5 PG1 (RD) (OC5A) PL3 PC0 (A8) 52 (OC5B) PL4 53 24 (T5) PL2 23 (OC1A/PCINT5) PB5 (ICP5) PL1 (OC2A/PCINT4) PB4 (ICP4) PL0 PC1 (A9) XTAL2 PC2 (A10) 54 XTAL1 55 22 VCC 21 (MISO/PCINT3) PB3 GND (MOSI/PCINT2) PB2 RESET PC3 (A11) (TOSC1) PG4 PC4 (A12) 56 (T4) PH7 57 20 (TOSC2) PG3 19 (OC0A/OC1C/PCINT7) PB7 (SS/PCINT0) PB0 (SCK/PCINT1) PB1 2 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 Figure 1-2. CBGA-pinout ATmega640/1280/2560 Top view 1 2 3 4 5 6 Bottom view 7 8 9 10 10 9 8 7 6 5 4 3 2 1 A A B B C C D D E E F F G G H H J J K K Table 1-1. CBGA-pinout ATmega640/1280/2560 1 2 3 4 5 6 7 8 9 10 A GND AREF PF0 PF2 PF5 PK0 PK3 PK6 GND VCC B AVCC PG5 PF1 PF3 PF6 PK1 PK4 PK7 PA0 PA2 C PE2 PE0 PE1 PF4 PF7 PK2 PK5 PJ7 PA1 PA3 D PE3 PE4 PE5 PE6 PH2 PA4 PA5 PA6 PA7 PG2 E PE7 PH0 PH1 PH3 PH5 PJ6 PJ5 PJ4 PJ3 PJ2 F VCC PH4 PH6 PB0 PL4 PD1 PJ1 PJ0 PC7 GND G GND PB1 PB2 PB5 PL2 PD0 PD5 PC5 PC6 VCC H PB3 PB4 RESET PL1 PL3 PL7 PD4 PC4 PC3 PC2 J PH7 PG3 PB6 PL0 XTAL2 PL6 PD3 PC1 PC0 PG1 K PB7 PG4 VCC GND XTAL1 PL5 PD2 PD6 PD7 PG0 Note: The functions for each pin is the same as for the 100 pin packages shown in Figure 1-1 on page 2. 3 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 (OC0B) PG5 1 (RXD0/PCINT8/PDI) PE0 2 AVCC GND AREF PF0 (ADC0) PF1 (ADC1) PF2 (ADC2) PF3 (ADC3) PF4 (ADC4/TCK) PF5 (ADC5/TMS) PF6 (ADC6/TDO) PF7 (ADC7/TDI) GND VCC PA0 (AD0) PA1 (AD1) PA2 (AD2) 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 Pinout ATmega1281/2561 64 Figure 1-3. INDEX CORNER 48 PA3 (AD3) 47 PA4 (AD4) 46 PA5 (AD5) 38 PC3 (A11) (MOSI/ PCINT2) PB2 12 37 PC2 (A10) (MISO/ PCINT3) PB3 13 36 PC1 (A9) (OC2A/ PCINT4) PB4 14 35 PC0 (A8) (OC1A/PCINT5) PB5 15 34 PG1 (RD) (OC1B/PCINT6) PB6 16 33 PG0 (WR) Note: 32 11 (T0) PD7 (SCK/ PCINT1) PB1 31 PC4 (A12) (T1) PD6 39 30 10 (XCK1) PD5 (SS/PCINT0) PB0 29 PC5 (A13) (ICP1) PD4 40 28 9 (TXD1/INT3) PD3 (ICP3/CLKO/INT7) PE7 27 PC6 (A14) (RXD1/INT2) PD2 41 26 8 (SDA/INT1) PD1 (T3/INT6) PE6 25 PC7 (A15) (SCL/INT0) PD0 42 24 7 XTAL1 (OC3C/INT5) PE5 23 PG2 (ALE) XTAL2 43 22 6 GND (OC3B/INT4) PE4 21 PA7 (AD7) VCC 44 20 5 RESET (OC3A/AIN1) PE3 19 PA6 (AD6) (TOSC1) PG4 45 18 4 (TOSC2) PG3 (XCK0/AIN0) PE2 17 3 (OC0A/OC1C/PCINT7) PB7 (TXD0/PDO) PE1 The large center pad underneath the QFN/MLF package is made of metal and internally connected to GND. It should be soldered or glued to the board to ensure good mechanical stability. If the center pad is left unconnected, the package might loosen from the board. 4 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 2. Overview The ATmega640/1280/1281/2560/2561 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega640/1280/1281/2560/2561 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. 2.1 Block Diagram Figure 2-1. Block Diagram PF7..0 PK7..0 PORT F (8) PORT K (8) PJ7..0 PE7..0 VCC Power Supervision POR/ BOD & RESET RESET PORT J (8) PORT E (8) Watchdog Timer GND Watchdog Oscillator Analog Comparator JTAG A/D Converter EEPROM Internal Bandgap reference USART 0 XTAL1 Oscillator Circuits / Clock Generation 16 bit T/C 3 USART 3 16 bit T/C 5 XTAL2 CPU PORT A (8) PA7..0 16 bit T/C 4 USART 1 PG5..0 PORT G (6) XRAM PC7..0 PORT C (8) TWI FLASH SPI SRAM 16 bit T/C 1 8 bit T/C 0 USART 2 8 bit T/C 2 NOTE: Shaded parts only available in the 100-pin version. Complete functionality for the ADC, T/C4, and T/C5 only available in the 100-pin version. PORT D (8) PORT B (8) PORT H (8) PORT L (8) PD7..0 PB7..0 PH7..0 PL7..0 5 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 The Atmel® AVR® core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The ATmega640/1280/1281/2560/2561 provides the following features: 64K/128K/256K bytes of In-System Programmable Flash with Read-While-Write capabilities, 4Kbytes EEPROM, 8 Kbytes SRAM, 54/86 general purpose I/O lines, 32 general purpose working registers, Real Time Counter (RTC), six flexible Timer/Counters with compare modes and PWM, 4 USARTs, a byte oriented 2-wire Serial Interface, a 16-channel, 10-bit ADC with optional differential input stage with programmable gain, programmable Watchdog Timer with Internal Oscillator, an SPI serial port, IEEE® std. 1149.1 compliant JTAG test interface, also used for accessing the Onchip Debug system and programming and six software selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt system to continue functioning. The Power-down mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next interrupt or Hardware Reset. In Powersave mode, the asynchronous timer continues to run, allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O modules except Asynchronous Timer and ADC, to minimize switching noise during ADC conversions. In Standby mode, the Crystal/Resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low power consumption. In Extended Standby mode, both the main Oscillator and the Asynchronous Timer continue to run. Atmel offers the QTouch® library for embedding capacitive touch buttons, sliders and wheelsfunctionality into AVR microcontrollers. The patented charge-transfer signal acquisition offersrobust sensing and includes fully debounced reporting of touch keys and includes Adjacent KeySuppression® (AKS™) technology for unambiguous detection of key events. The easy-to-use QTouch Suite toolchain allows you to explore, develop and debug your own touch applications. The device is manufactured using Atmel’s high-density nonvolatile memory technology. The Onchip ISP Flash allows the program memory to be reprogrammed in-system through an SPI serial interface, by a conventional nonvolatile memory programmer, or by an On-chip Boot program running on the AVR core. The boot program can use any interface to download the application program in the application Flash memory. Software in the Boot Flash section will continue to run while the Application Flash section is updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATmega640/1280/1281/2560/2561 is a powerful microcontroller that provides a highly flexible and cost effective solution to many embedded control applications. The ATmega640/1280/1281/2560/2561 AVR is supported with a full suite of program and system development tools including: C compilers, macro assemblers, program debugger/simulators, in-circuit emulators, and evaluation kits. 6 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 2.2 Comparison Between ATmega1281/2561 and ATmega640/1280/2560 Each device in the ATmega640/1280/1281/2560/2561 family differs only in memory size and number of pins. Table 2-1 summarizes the different configurations for the six devices. Table 2-1. Configuration Summary Flash EEPROM RAM General Purpose I/O pins 16 bits resolution PWM channels Serial USARTs ADC Channels ATmega640 64KB 4KB 8KB 86 12 4 16 ATmega1280 128KB 4KB 8KB 86 12 4 16 ATmega1281 128KB 4KB 8KB 54 6 2 8 ATmega2560 256KB 4KB 8KB 86 12 4 16 ATmega2561 256KB 4KB 8KB 54 6 2 8 Device 2.3 2.3.1 Pin Descriptions VCC Digital supply voltage. 2.3.2 GND Ground. 2.3.3 Port A (PA7..PA0) Port A is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port A output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port A pins that are externally pulled low will source current if the pull-up resistors are activated. The Port A pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port A also serves the functions of various ATmega640/1280/1281/2560/2561 as listed on page 78. 2.3.4 special features of the Port B (PB7..PB0) Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port B has better driving capabilities than the other ports. Port B also serves the functions of various ATmega640/1280/1281/2560/2561 as listed on page 79. 2.3.5 special features of the Port C (PC7..PC0) Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up 7 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 resistors are activated. The Port C pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port C also serves the functions of special features of the ATmega640/1280/1281/2560/2561 as listed on page 82. 2.3.6 Port D (PD7..PD0) Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D also serves the functions of various ATmega640/1280/1281/2560/2561 as listed on page 83. 2.3.7 features of the Port E (PE7..PE0) Port E is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port E output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port E pins that are externally pulled low will source current if the pull-up resistors are activated. The Port E pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port E also serves the functions of various ATmega640/1280/1281/2560/2561 as listed on page 86. 2.3.8 special special features of the Port F (PF7..PF0) Port F serves as analog inputs to the A/D Converter. Port F also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins can provide internal pull-up resistors (selected for each bit). The Port F output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port F pins that are externally pulled low will source current if the pull-up resistors are activated. The Port F pins are tri-stated when a reset condition becomes active, even if the clock is not running. If the JTAG interface is enabled, the pull-up resistors on pins PF7(TDI), PF5(TMS), and PF4(TCK) will be activated even if a reset occurs. Port F also serves the functions of the JTAG interface. 2.3.9 Port G (PG5..PG0) Port G is a 6-bit I/O port with internal pull-up resistors (selected for each bit). The Port G output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port G pins that are externally pulled low will source current if the pull-up resistors are activated. The Port G pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port G also serves the functions of various ATmega640/1280/1281/2560/2561 as listed on page 90. 2.3.10 special features of the Port H (PH7..PH0) Port H is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port H output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port H pins that are externally pulled low will source current if the pull-up 8 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 resistors are activated. The Port H pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port H also serves the functions of various special features of the ATmega640/1280/2560 as listed on page 92. 2.3.11 Port J (PJ7..PJ0) Port J is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port J output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port J pins that are externally pulled low will source current if the pull-up resistors are activated. The Port J pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port J also serves the functions of various special features of the ATmega640/1280/2560 as listed on page 94. 2.3.12 Port K (PK7..PK0) Port K serves as analog inputs to the A/D Converter. Port K is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port K output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port K pins that are externally pulled low will source current if the pull-up resistors are activated. The Port K pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port K also serves the functions of various special features of the ATmega640/1280/2560 as listed on page 96. 2.3.13 Port L (PL7..PL0) Port L is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port L output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port L pins that are externally pulled low will source current if the pull-up resistors are activated. The Port L pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port L also serves the functions of various special features of the ATmega640/1280/2560 as listed on page 98. 2.3.14 RESET Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not running. The minimum pulse length is given in “System and Reset Characteristics” on page 372. Shorter pulses are not guaranteed to generate a reset. 2.3.15 XTAL1 Input to the inverting Oscillator amplifier and input to the internal clock operating circuit. 2.3.16 XTAL2 Output from the inverting Oscillator amplifier. 9 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 2.3.17 AVCC AVCC is the supply voltage pin for Port F and the A/D Converter. It should be externally connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter. 2.3.18 AREF This is the analog reference pin for the A/D Converter. 10 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 3. Resources A comprehensive set of development tools and application notes, and datasheets are available for download on http://www.atmel.com/avr. 4. About Code Examples This documentation contains simple code examples that briefly show how to use various parts of the device. Be aware that not all C compiler vendors include bit definitions in the header files and interrupt handling in C is compiler dependent. Please confirm with the C compiler documentation for more details. These code examples assume that the part specific header file is included before compilation. For I/O registers located in extended I/O map, "IN", "OUT", "SBIS", "SBIC", "CBI", and "SBI" instructions must be replaced with instructions that allow access to extended I/O. Typically "LDS" and "STS" combined with "SBRS", "SBRC", "SBR", and "CBR". 5. Data Retention Reliability Qualification results show that the projected data retention failure rate is much less than 1 ppm over 20 years at 85°C or 100 years at 25°C. 6. Capacitive touch sensing The Atmel®QTouch® Library provides a simple to use solution to realize touch sensitive interfaces on most Atmel AVR ® microcontrollers. The QTouch Library includes support for the QTouch and QMatrix® acquisition methods. Touch sensing can be added to any application by linking the appropriate Atmel QTouch Library for the AVR Microcontroller. This is done by using a simple set of APIs to define the touch channels and sensors, and then calling the touch sensing API’s to retrieve the channel information and determine the touch sensor states. The QTouch Library is FREE and downloadable from the Atmel website at the following location: www.atmel.com/qtouchlibrary. For implementation details and other information, refer to the Atmel QTouch Library User Guide - also available for download from the Atmel website. 11 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 7. Register Summary Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (0x1FF) Reserved - - - - - - - - - - - - - - - - - - - ... Reserved (0x13F) Reserved (0x13E) Reserved (0x13D) Reserved (0x13C) Reserved (0x13B) Reserved (0x13A) Reserved (0x139) Reserved (0x138) Reserved (0x137) Reserved (0x136) UDR3 (0x135) UBRR3H USART3 I/O Data Register (0x134) UBRR3L (0x133) Reserved - - (0x132) UCSR3C UMSEL31 (0x131) UCSR3B RXCIE3 - 222 USART3 Baud Rate Register High Byte 227 USART3 Baud Rate Register Low Byte - - - UMSEL30 UPM31 UPM30 TXCIE3 UDRIE3 RXEN3 Page 227 - - - USBS3 UCSZ31 UCSZ30 UCPOL3 239 TXEN3 UCSZ32 RXB83 TXB83 238 238 (0x130) UCSR3A RXC3 TXC3 UDRE3 FE3 DOR3 UPE3 U2X3 MPCM3 (0x12F) Reserved - - - - - - - - - - - - - - - - (0x12E) Reserved (0x12D) OCR5CH Timer/Counter5 - Output Compare Register C High Byte 165 (0x12C) OCR5CL Timer/Counter5 - Output Compare Register C Low Byte 165 (0x12B) OCR5BH Timer/Counter5 - Output Compare Register B High Byte 165 (0x12A) OCR5BL Timer/Counter5 - Output Compare Register B Low Byte 165 (0x129) OCR5AH Timer/Counter5 - Output Compare Register A High Byte 164 (0x128) OCR5AL Timer/Counter5 - Output Compare Register A Low Byte 164 (0x127) ICR5H Timer/Counter5 - Input Capture Register High Byte 165 (0x126) ICR5L Timer/Counter5 - Input Capture Register Low Byte 165 (0x125) TCNT5H Timer/Counter5 - Counter Register High Byte 163 (0x124) TCNT5L (0x123) Reserved - - - Timer/Counter5 - Counter Register Low Byte - - 163 - - - (0x122) TCCR5C FOC5A FOC5B FOC5C - - - - - 162 (0x121) TCCR5B ICNC5 ICES5 - WGM53 WGM52 CS52 CS51 CS50 160 (0x120) TCCR5A COM5A1 COM5A0 COM5B1 COM5B0 COM5C1 COM5C0 WGM51 WGM50 158 (0x11F) Reserved - - - - - - - - (0x11E) Reserved - - - - - - - - (0x11D) Reserved - - - - - - - - (0x11C) Reserved - - - - - - - - (0x11B) Reserved - - - - - - - - (0x11A) Reserved - - - - - - - - (0x119) Reserved - - - - - - - - (0x118) Reserved - - - - - - - - (0x117) Reserved - - - - - - - - (0x116) Reserved - - - - - - - - (0x115) Reserved - - - - - - - - (0x114) Reserved - - - - - - - - (0x113) Reserved - - - - - - - - (0x112) Reserved - - - - - - - - (0x111) Reserved - - - - - - - - (0x110) Reserved - - - - - - - - (0x10F) Reserved - - - - - - - - (0x10E) Reserved - - - - - - - - (0x10D) Reserved - - - - - - - - (0x10C) Reserved - - - - - - - - (0x10B) PORTL PORTL7 PORTL6 PORTL5 PORTL4 PORTL3 PORTL2 PORTL1 PORTL0 104 (0x10A) DDRL DDL7 DDL6 DDL5 DDL4 DDL3 DDL2 DDL1 DDL0 104 (0x109) PINL PINL7 PINL6 PINL5 PINL4 PINL3 PINL2 PINL1 PINL0 104 (0x108) PORTK PORTK7 PORTK6 PORTK5 PORTK4 PORTK3 PORTK2 PORTK1 PORTK0 103 (0x107) DDRK DDK7 DDK6 DDK5 DDK4 DDK3 DDK2 DDK1 DDK0 103 (0x106) PINK PINK7 PINK6 PINK5 PINK4 PINK3 PINK2 PINK1 PINK0 103 (0x105) PORTJ PORTJ7 PORTJ6 PORTJ5 PORTJ4 PORTJ3 PORTJ2 PORTJ1 PORTJ0 103 (0x104) DDRJ DDJ7 DDJ6 DDJ5 DDJ4 DDJ3 DDJ2 DDJ1 DDJ0 103 (0x103) PINJ PINJ7 PINJ6 PINJ5 PINJ4 PINJ3 PINJ2 PINJ1 PINJ0 103 (0x102) PORTH PORTH7 PORTH6 PORTH5 PORTH4 PORTH3 PORTH2 PORTH1 PORTH0 102 (0x101) DDRH DDH7 DDH6 DDH5 DDH4 DDH3 DDH2 DDH1 DDH0 103 12 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page (0x100) PINH PINH7 PINH6 PINH5 PINH4 PINH3 PINH2 PINH1 PINH0 103 (0xFF) Reserved - - - - - - - - (0xFE) Reserved - - - - - - - - (0xFD) Reserved - - - - - - - - (0xFC) Reserved - - - - - - - - (0xFB) Reserved - - - - - - - - (0xFA) Reserved - - - - - - - - (0xF9) Reserved - - - - - - - - (0xF8) Reserved - - - - - - - - (0xF7) Reserved - - - - - - - - (0xF6) Reserved - - - - - - - - (0xF5) Reserved - - - - - - - - (0xF4) Reserved - - - - - - - - (0xF3) Reserved - - - - - - - - (0xF2) Reserved - - - - - - - - (0xF1) Reserved - - - - - - - - (0xF0) Reserved - - - - - - - - (0xEF) Reserved - - - - - - - - (0xEE) Reserved - - - - - - - - (0xED) Reserved - - - - - - - - (0xEC) Reserved - - - - - - - - (0xEB) Reserved - - - - - - - (0xEA) Reserved - - - - - - - - (0xE9) Reserved - - - - - - - - (0xE8) Reserved - - - - - - - - (0xE7) Reserved - - - - - - - (0xE6) Reserved - - - - - - - - (0xE5) Reserved - - - - - - - - (0xE4) Reserved - - - - - - - - (0xE3) Reserved - - - - - - - (0xE2) Reserved - - - - - - - (0xE1) Reserved - - - - - - - (0xE0) Reserved - - - - - - - (0xDF) Reserved - - - - - - - - (0xDE) Reserved - - - - - - - - (0xDD) Reserved - - - - - - - (0xDC) Reserved - - - - - - - - (0xDB) Reserved - - - - - - - - (0xDA) Reserved - - - - - - - - (0xD9) Reserved - - - - - - - (0xD8) Reserved - - - - - - - - (0xD7) Reserved - - - - - - - - (0xD6) UDR2 (0xD5) UBRR2H (0xD4) UBRR2L (0xD3) Reserved - - (0xD2) UCSR2C UMSEL21 UMSEL20 (0xD1) UCSR2B RXCIE2 TXCIE2 (0xD0) UCSR2A RXC2 TXC2 (0xCF) Reserved - - USART2 I/O Data Register - - - - 222 USART2 Baud Rate Register High Byte 227 USART2 Baud Rate Register Low Byte - 227 - - - - - UPM21 UPM20 USBS2 UCSZ21 UCSZ20 UCPOL2 239 UDRIE2 RXEN2 TXEN2 UCSZ22 RXB82 TXB82 238 UDRE2 FE2 DOR2 UPE2 U2X2 MPCM2 238 - - - - - - - - - (0xCE) UDR1 (0xCD) UBRR1H USART1 I/O Data Register (0xCC) UBRR1L (0xCB) Reserved - - (0xCA) UCSR1C UMSEL11 UMSEL10 (0xC9) UCSR1B RXCIE1 TXCIE1 (0xC8) UCSR1A RXC1 TXC1 (0xC7) Reserved - - - - - - 222 USART1 Baud Rate Register High Byte 227 USART1 Baud Rate Register Low Byte (0xC6) UDR0 (0xC5) UBRR0H (0xC4) UBRR0L (0xC3) Reserved - - (0xC2) UCSR0C UMSEL01 UMSEL00 (0xC1) UCSR0B RXCIE0 TXCIE0 (0xC0) UCSR0A RXC0 TXC0 (0xBF) Reserved - - - 227 - - - - - UPM11 UPM10 USBS1 UCSZ11 UCSZ10 UCPOL1 239 UDRIE1 RXEN1 TXEN1 UCSZ12 RXB81 TXB81 238 UDRE1 FE1 DOR1 UPE1 U2X1 MPCM1 238 - - - - - - USART0 I/O Data Register - 222 USART0 Baud Rate Register High Byte 227 USART0 Baud Rate Register Low Byte - 227 - - - - - UPM01 UPM00 USBS0 UCSZ01 UCSZ00 UCPOL0 239 UDRIE0 RXEN0 TXEN0 UCSZ02 RXB80 TXB80 238 UDRE0 FE0 DOR0 UPE0 U2X0 MPCM0 238 - - - - - - 13 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (0xBE) Reserved - - - - - - - - (0xBD) TWAMR TWAM6 TWAM5 TWAM4 TWAM3 TWAM2 TWAM1 TWAM0 - 269 (0xBC) TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN - TWIE 266 (0xBB) TWDR (0xBA) TWAR TWA6 TWA5 TWA4 TWA3 TWA2 TWA1 TWA0 TWGCE 269 (0xB9) TWSR TWS7 TWS6 TWS5 TWS4 TWS3 - TWPS1 TWPS0 268 2-wire Serial Interface Data Register Page 268 (0xB8) TWBR (0xB7) Reserved - - - 2-wire Serial Interface Bit Rate Register - - - - - 266 (0xB6) ASSR - EXCLK AS2 TCN2UB OCR2AUB OCR2BUB TCR2AUB TCR2BUB (0xB5) Reserved - - - - - - - - (0xB4) OCR2B Timer/Counter2 Output Compare Register B 191 (0xB3) OCR2A Timer/Counter2 Output Compare Register A 191 (0xB2) TCNT2 Timer/Counter2 (8 Bit) (0xB1) TCCR2B FOC2A FOC2B - - WGM22 CS22 CS21 CS20 190 (0xB0) TCCR2A COM2A1 COM2A0 COM2B1 COM2B0 - - WGM21 WGM20 191 (0xAF) Reserved - - - - - - - - - - - - - - - - 184 191 (0xAE) Reserved (0xAD) OCR4CH Timer/Counter4 - Output Compare Register C High Byte 164 (0xAC) OCR4CL Timer/Counter4 - Output Compare Register C Low Byte 164 (0xAB) OCR4BH Timer/Counter4 - Output Compare Register B High Byte 164 (0xAA) OCR4BL Timer/Counter4 - Output Compare Register B Low Byte 164 (0xA9) OCR4AH Timer/Counter4 - Output Compare Register A High Byte 164 (0xA8) OCR4AL Timer/Counter4 - Output Compare Register A Low Byte 164 (0xA7) ICR4H Timer/Counter4 - Input Capture Register High Byte 165 (0xA6) ICR4L Timer/Counter4 - Input Capture Register Low Byte 165 (0xA5) TCNT4H Timer/Counter4 - Counter Register High Byte 163 (0xA4) TCNT4L Timer/Counter4 - Counter Register Low Byte (0xA3) Reserved - - - (0xA2) TCCR4C FOC4A FOC4B FOC4C - - - - - 162 (0xA1) TCCR4B ICNC4 ICES4 - WGM43 WGM42 CS42 CS41 CS40 160 (0xA0) TCCR4A COM4A1 COM4A0 COM4B1 COM4B0 COM4C1 COM4C0 WGM41 WGM40 158 (0x9F) Reserved - - - - - - - - - - - - - - - - - - 163 - - - (0x9E) Reserved (0x9D) OCR3CH Timer/Counter3 - Output Compare Register C High Byte 164 (0x9C) OCR3CL Timer/Counter3 - Output Compare Register C Low Byte 164 (0x9B) OCR3BH Timer/Counter3 - Output Compare Register B High Byte 164 (0x9A) OCR3BL Timer/Counter3 - Output Compare Register B Low Byte 164 (0x99) OCR3AH Timer/Counter3 - Output Compare Register A High Byte 163 (0x98) OCR3AL Timer/Counter3 - Output Compare Register A Low Byte 163 (0x97) ICR3H Timer/Counter3 - Input Capture Register High Byte 165 (0x96) ICR3L Timer/Counter3 - Input Capture Register Low Byte 165 (0x95) TCNT3H Timer/Counter3 - Counter Register High Byte 162 (0x94) TCNT3L Timer/Counter3 - Counter Register Low Byte (0x93) Reserved - - - - - 162 - - - (0x92) TCCR3C FOC3A FOC3B FOC3C - - - - - 162 (0x91) TCCR3B ICNC3 ICES3 - WGM33 WGM32 CS32 CS31 CS30 160 (0x90) TCCR3A COM3A1 COM3A0 COM3B1 COM3B0 COM3C1 COM3C0 WGM31 WGM30 158 (0x8F) Reserved - - - - - - - - - - - - - - - - (0x8E) Reserved (0x8D) OCR1CH Timer/Counter1 - Output Compare Register C High Byte 163 (0x8C) OCR1CL Timer/Counter1 - Output Compare Register C Low Byte 163 (0x8B) OCR1BH Timer/Counter1 - Output Compare Register B High Byte 163 (0x8A) OCR1BL Timer/Counter1 - Output Compare Register B Low Byte 163 (0x89) OCR1AH Timer/Counter1 - Output Compare Register A High Byte 163 (0x88) OCR1AL Timer/Counter1 - Output Compare Register A Low Byte 163 (0x87) ICR1H Timer/Counter1 - Input Capture Register High Byte 165 (0x86) ICR1L Timer/Counter1 - Input Capture Register Low Byte 165 (0x85) TCNT1H Timer/Counter1 - Counter Register High Byte 162 (0x84) TCNT1L Timer/Counter1 - Counter Register Low Byte (0x83) Reserved - - - - - 162 - - - (0x82) TCCR1C FOC1A FOC1B FOC1C - - - - - 161 (0x81) TCCR1B ICNC1 ICES1 - WGM13 WGM12 CS12 CS11 CS10 160 (0x80) TCCR1A COM1A1 COM1A0 COM1B1 COM1B0 COM1C1 COM1C0 WGM11 WGM10 158 (0x7F) DIDR1 - - - - - - AIN1D AIN0D 274 (0x7E) DIDR0 ADC7D ADC6D ADC5D ADC4D ADC3D ADC2D ADC1D ADC0D 295 (0x7D) DIDR2 ADC15D ADC14D ADC13D ADC12D ADC11D ADC10D ADC9D ADC8D 295 14 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (0x7C) ADMUX REFS1 REFS0 ADLAR MUX4 MUX3 MUX2 MUX1 MUX0 Page 289 (0x7B) ADCSRB - ACME - - MUX5 ADTS2 ADTS1 ADTS0 272, 290, 294 (0x7A) ADCSRA ADEN ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 292 (0x79) ADCH ADC Data Register High byte (0x78) ADCL ADC Data Register Low byte (0x77) Reserved (0x76) (0x75) 294 294 - - - - - - - - Reserved - - - - - - - - XMCRB XMBK - - - - XMM2 XMM1 XMM0 (0x74) XMCRA SRE SRL2 SRL1 SRL0 SRW11 SRW10 SRW01 SRW00 37 (0x73) TIMSK5 - - ICIE5 - OCIE5C OCIE5B OCIE5A TOIE5 166 (0x72) TIMSK4 - - ICIE4 - OCIE4C OCIE4B OCIE4A TOIE4 166 (0x71) TIMSK3 - - ICIE3 - OCIE3C OCIE3B OCIE3A TOIE3 166 (0x70) TIMSK2 - - - - - OCIE2B OCIE2A TOIE2 193 (0x6F) TIMSK1 - - ICIE1 - OCIE1C OCIE1B OCIE1A TOIE1 166 (0x6E) TIMSK0 - - - - - OCIE0B OCIE0A TOIE0 134 (0x6D) PCMSK2 PCINT23 PCINT22 PCINT21 PCINT20 PCINT19 PCINT18 PCINT17 PCINT16 116 (0x6C) PCMSK1 PCINT15 PCINT14 PCINT13 PCINT12 PCINT11 PCINT10 PCINT9 PCINT8 116 (0x6B) PCMSK0 PCINT7 PCINT6 PCINT5 PCINT4 PCINT3 PCINT2 PCINT1 PCINT0 117 (0x6A) EICRB ISC71 ISC70 ISC61 ISC60 ISC51 ISC50 ISC41 ISC40 114 (0x69) EICRA ISC31 ISC30 ISC21 ISC20 ISC11 ISC10 ISC01 ISC00 113 (0x68) PCICR - - - - - PCIE2 PCIE1 PCIE0 115 (0x67) Reserved - - - - - - - - (0x66) OSCCAL (0x65) PRR1 - - PRTIM5 PRTIM4 PRTIM3 PRUSART3 PRUSART2 PRUSART1 57 (0x64) PRR0 PRTWI PRTIM2 PRTIM0 - PRTIM1 PRSPI PRUSART0 PRADC 56 (0x63) Reserved - - - - - - - - (0x62) Reserved - - - - - - - - (0x61) CLKPR CLKPCE - - - CLKPS3 CLKPS2 CLKPS1 CLKPS0 50 (0x60) WDTCSR WDIF WDIE WDP3 WDCE WDE WDP2 WDP1 WDP0 67 0x3F (0x5F) SREG I T H S V N Z C 14 0x3E (0x5E) SPH SP15 SP14 SP13 SP12 SP11 SP10 SP9 SP8 16 0x3D (0x5D) SPL SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 16 0x3C (0x5C) EIND - - - - - - - EIND0 17 0x3B (0x5B) RAMPZ - - - - - - RAMPZ1 RAMPZ0 17 0x3A (0x5A) Reserved - - - - - - - - 0x39 (0x59) Reserved - - - - - - - - 0x38 (0x58) Reserved - - - - - - - - 0x37 (0x57) SPMCSR SPMIE RWWSB SIGRD RWWSRE BLBSET PGWRT PGERS SPMEN 0x36 (0x56) Reserved - - - - - - - - 0x35 (0x55) MCUCR JTD - - PUD - - IVSEL IVCE 67, 110, 100, 308 0x34 (0x54) MCUSR - - - JTRF WDRF BORF EXTRF PORF 308 0x33 (0x53) SMCR - - - - SM2 SM1 SM0 SE 52 0x32 (0x52) Reserved - - - - - - - - 0x31 (0x51) OCDR OCDR7 OCDR6 OCDR5 OCDR4 OCDR3 OCDR2 OCDR1 OCDR0 301 0x30 (0x50) ACSR ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 272 0x2F (0x4F) Reserved - - - - - - - - Oscillator Calibration Register 38 50 SPI Data Register 332 0x2E (0x4E) SPDR 0x2D (0x4D) SPSR SPIF WCOL - - - - - SPI2X 203 0x2C (0x4C) SPCR SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 202 0x2B (0x4B) GPIOR2 General Purpose I/O Register 2 0x2A (0x4A) GPIOR1 General Purpose I/O Register 1 0x29 (0x49) Reserved 0x28 (0x48) OCR0B Timer/Counter0 Output Compare Register B 133 0x27 (0x47) OCR0A Timer/Counter0 Output Compare Register A 133 0x26 (0x46) TCNT0 Timer/Counter0 (8 Bit) 0x25 (0x45) TCCR0B FOC0A FOC0B - - WGM02 CS02 CS01 CS00 0x24 (0x44) TCCR0A COM0A1 COM0A0 COM0B1 COM0B0 - - WGM01 WGM00 129 0x23 (0x43) GTCCR TSM - - - - - PSRASY PSRSYNC 170, 194 - - - - - - - 204 37 37 - - - EEPROM Address Register High Byte 0x22 (0x42) EEARH EEARL EEPROM Address Register Low Byte 0x20 (0x40) EEDR EEPROM Data Register 0x1F (0x3F) EECR 0x1E (0x3E) GPIOR0 0x1D (0x3D) EIMSK INT7 INT6 INT5 INT4 INT3 0x1C (0x3C) EIFR INTF7 INTF6 INTF5 INTF4 INTF3 INTF2 0x1B (0x3B) PCIFR - - - - - PCIF2 - EEPM1 EEPM0 - 133 0x21 (0x41) - - EERIE 132 35 35 35 EEMPE EEPE EERE 35 INT2 INT1 INT0 115 INTF1 INTF0 115 PCIF1 PCIF0 116 General Purpose I/O Register 0 37 15 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page 0x1A (0x3A) TIFR5 - - ICF5 - OCF5C OCF5B OCF5A TOV5 166 0x19 (0x39) TIFR4 - - ICF4 - OCF4C OCF4B OCF4A TOV4 167 0x18 (0x38) TIFR3 - - ICF3 - OCF3C OCF3B OCF3A TOV3 167 0x17 (0x37) TIFR2 - - - - - OCF2B OCF2A TOV2 193 0x16 (0x36) TIFR1 - - ICF1 - OCF1C OCF1B OCF1A TOV1 167 0x15 (0x35) TIFR0 - - - - - OCF0B OCF0A TOV0 134 0x14 (0x34) PORTG - - PORTG5 PORTG4 PORTG3 PORTG2 PORTG1 PORTG0 102 0x13 (0x33) DDRG - - DDG5 DDG4 DDG3 DDG2 DDG1 DDG0 102 0x12 (0x32) PING - - PING5 PING4 PING3 PING2 PING1 PING0 102 0x11 (0x31) PORTF PORTF7 PORTF6 PORTF5 PORTF4 PORTF3 PORTF2 PORTF1 PORTF0 101 0x10 (0x30) DDRF DDF7 DDF6 DDF5 DDF4 DDF3 DDF2 DDF1 DDF0 102 0x0F (0x2F) PINF PINF7 PINF6 PINF5 PINF4 PINF3 PINF2 PINF1 PINF0 102 0x0E (0x2E) PORTE PORTE7 PORTE6 PORTE5 PORTE4 PORTE3 PORTE2 PORTE1 PORTE0 101 0x0D (0x2D) DDRE DDE7 DDE6 DDE5 DDE4 DDE3 DDE2 DDE1 DDE0 101 0x0C (0x2C) PINE PINE7 PINE6 PINE5 PINE4 PINE3 PINE2 PINE1 PINE0 102 0x0B (0x2B) PORTD PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 101 0x0A (0x2A) DDRD DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 101 0x09 (0x29) PIND PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 101 0x08 (0x28) PORTC PORTC7 PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 101 0x07 (0x27) DDRC DDC7 DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 101 0x06 (0x26) PINC PINC7 PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 101 0x05 (0x25) PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 100 0x04 (0x24) DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 100 0x03 (0x23) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 100 0x02 (0x22) PORTA PORTA7 PORTA6 PORTA5 PORTA4 PORTA3 PORTA2 PORTA1 PORTA0 100 0x01 (0x21) DDRA DDA7 DDA6 DDA5 DDA4 DDA3 DDA2 DDA1 DDA0 100 0x00 (0x20) PINA PINA7 PINA6 PINA5 PINA4 PINA3 PINA2 PINA1 PINA0 100 Notes: 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. 2. I/O registers within the address range $00 - $1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the value of single bits can be checked by using the SBIS and SBIC instructions. 3. Some of the status flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on all bits in the I/O register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers 0x00 to 0x1F only. 4. When using the I/O specific commands IN and OUT, the I/O addresses $00 - $3F must be used. When addressing I/O registers as data space using LD and ST instructions, $20 must be added to these addresses. The ATmega640/1280/1281/2560/2561 is a complex microcontroller with more peripheral units than can be supported within the 64 location reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from $60 - $1FF in SRAM, only the ST/STS/STD and LD/LDS/LDD instructions can be used. 16 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 8. Instruction Set Summary Mnemonics Operands Description Operation Flags #Clocks ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers Rd ← Rd + Rr Z, C, N, V, H 1 ADC Rd, Rr Add with Carry two Registers Rd ← Rd + Rr + C Z, C, N, V, H 1 ADIW Rdl,K Add Immediate to Word Rdh:Rdl ← Rdh:Rdl + K Z, C, N, V, S 2 SUB Rd, Rr Subtract two Registers Rd ← Rd - Rr Z, C, N, V, H 1 SUBI Rd, K Subtract Constant from Register Rd ← Rd - K Z, C, N, V, H 1 SBC Rd, Rr Subtract with Carry two Registers Rd ← Rd - Rr - C Z, C, N, V, H 1 SBCI Rd, K Subtract with Carry Constant from Reg. Rd ← Rd - K - C Z, C, N, V, H 1 SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl ← Rdh:Rdl - K Z, C, N, V, S 2 AND Rd, Rr Logical AND Registers Rd ← Rd • Rr Z, N, V 1 ANDI Rd, K Logical AND Register and Constant Rd ← Rd • K Z, N, V 1 OR Rd, Rr Logical OR Registers Rd ← Rd v Rr Z, N, V 1 ORI Rd, K Logical OR Register and Constant Rd ← Rd v K Z, N, V 1 EOR Rd, Rr Exclusive OR Registers Rd ← Rd ⊕ Rr Z, N, V 1 COM Rd One’s Complement Rd ← 0xFF − Rd Z, C, N, V 1 NEG Rd Two’s Complement Rd ← 0x00 − Rd Z, C, N, V, H 1 SBR Rd,K Set Bit(s) in Register Rd ← Rd v K Z, N, V 1 CBR Rd,K Clear Bit(s) in Register Rd ← Rd • (0xFF - K) Z, N, V 1 INC Rd Increment Rd ← Rd + 1 Z, N, V 1 DEC Rd Decrement Rd ← Rd − 1 Z, N, V 1 TST Rd Test for Zero or Minus Rd ← Rd • Rd Z, N, V 1 CLR Rd Clear Register Rd ← Rd ⊕ Rd Z, N, V 1 SER Rd Set Register Rd ← 0xFF None 1 MUL Rd, Rr Multiply Unsigned R1:R0 ← Rd x Rr Z, C 2 MULS Rd, Rr Multiply Signed R1:R0 ← Rd x Rr Z, C 2 MULSU Rd, Rr Multiply Signed with Unsigned R1:R0 ← Rd x Rr Z, C 2 FMUL Rd, Rr Fractional Multiply Unsigned R1:R0 ← (Rd x Rr) << Z, C 2 FMULS Rd, Rr Fractional Multiply Signed Z, C 2 FMULSU Rd, Rr Fractional Multiply Signed with Unsigned Z, C 2 1 R1:R0 ← (Rd x Rr) << 1 R1:R0 ← (Rd x Rr) << 1 BRANCH INSTRUCTIONS RJMP k Relative Jump PC ← PC + k + 1 None 2 Indirect Jump to (Z) None 2 None 2 None 3 4 Extended Indirect Jump to (Z) PC ← Z PC ←(EIND:Z) JMP k Direct Jump PC ← k RCALL k IJMP EIJMP Relative Subroutine Call PC ← PC + k + 1 None ICALL Indirect Call to (Z) None 4 EICALL Extended Indirect Call to (Z) PC ← Z PC ←(EIND:Z) None 4 Direct Subroutine Call PC ← k None 5 RET Subroutine Return PC ← STACK None 5 RETI Interrupt Return PC ← STACK I Compare, Skip if Equal if (Rd = Rr) PC ← PC + 2 or 3 None CALL CPSE k Rd,Rr 5 1/2/3 CP Rd,Rr Compare Rd − Rr Z, N, V, C, H 1 CPC Rd,Rr Compare with Carry Rd − Rr − C Z, N, V, C, H 1 CPI Rd,K Compare Register with Immediate Rd − K Z, N, V, C, H SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC ← PC + 2 or 3 None 1 1/2/3 SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC ← PC + 2 or 3 None 1/2/3 SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC ← PC + 2 or 3 None 1/2/3 1/2/3 SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC ← PC + 2 or 3 None BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC←PC+k + 1 None 1/2 BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC←PC+k + 1 None 1/2 BREQ k Branch if Equal if (Z = 1) then PC ← PC + k + 1 None 1/2 BRNE k Branch if Not Equal if (Z = 0) then PC ← PC + k + 1 None 1/2 BRCS k Branch if Carry Set if (C = 1) then PC ← PC + k + 1 None 1/2 BRCC k Branch if Carry Cleared if (C = 0) then PC ← PC + k + 1 None 1/2 BRSH k Branch if Same or Higher if (C = 0) then PC ← PC + k + 1 None 1/2 BRLO k Branch if Lower if (C = 1) then PC ← PC + k + 1 None 1/2 BRMI k Branch if Minus if (N = 1) then PC ← PC + k + 1 None 1/2 BRPL k Branch if Plus if (N = 0) then PC ← PC + k + 1 None 1/2 1/2 BRGE k Branch if Greater or Equal, Signed if (N ⊕ V= 0) then PC ← PC + k + 1 None BRLT k Branch if Less Than Zero, Signed if (N ⊕ V= 1) then PC ← PC + k + 1 None 1/2 BRHS k Branch if Half Carry Flag Set if (H = 1) then PC ← PC + k + 1 None 1/2 1/2 BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC ← PC + k + 1 None BRTS k Branch if T Flag Set if (T = 1) then PC ← PC + k + 1 None 1/2 BRTC k Branch if T Flag Cleared if (T = 0) then PC ← PC + k + 1 None 1/2 17 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 Mnemonics Operands Description Operation Flags #Clocks BRVS k Branch if Overflow Flag is Set if (V = 1) then PC ← PC + k + 1 None 1/2 BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC ← PC + k + 1 None 1/2 BRIE k Branch if Interrupt Enabled if ( I = 1) then PC ← PC + k + 1 None 1/2 BRID k Branch if Interrupt Disabled if ( I = 0) then PC ← PC + k + 1 None 1/2 BIT AND BIT-TEST INSTRUCTIONS SBI P,b Set Bit in I/O Register I/O(P,b) ← 1 None 2 CBI P,b Clear Bit in I/O Register I/O(P,b) ← 0 None 2 LSL Rd Logical Shift Left Rd(n+1) ← Rd(n), Rd(0) ← 0 Z, C, N, V 1 LSR Rd Logical Shift Right Rd(n) ← Rd(n+1), Rd(7) ← 0 Z, C, N, V 1 ROL Rd Rotate Left Through Carry Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7) Z, C, N, V 1 ROR Rd Rotate Right Through Carry Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0) Z, C, N, V 1 ASR Rd Arithmetic Shift Right Rd(n) ← Rd(n+1), n=0..6 Z, C, N, V 1 SWAP Rd Swap Nibbles Rd(3..0)←Rd(7..4),Rd(7..4)←Rd(3..0) None 1 BSET s Flag Set SREG(s) ← 1 SREG(s) 1 BCLR s Flag Clear SREG(s) ← 0 SREG(s) 1 BST Rr, b Bit Store from Register to T T ← Rr(b) T 1 BLD Rd, b Bit load from T to Register Rd(b) ← T None 1 SEC Set Carry C←1 C 1 CLC Clear Carry C←0 C 1 SEN Set Negative Flag N←1 N 1 CLN Clear Negative Flag N←0 N 1 SEZ Set Zero Flag Z←1 Z 1 CLZ Clear Zero Flag Z←0 Z 1 SEI Global Interrupt Enable I←1 I 1 CLI Global Interrupt Disable I←0 I 1 SES Set Signed Test Flag S←1 S 1 CLS Clear Signed Test Flag S←0 S 1 SEV Set Twos Complement Overflow. V←1 V 1 CLV Clear Twos Complement Overflow V←0 V 1 SET Set T in SREG T←1 T 1 CLT Clear T in SREG T←0 T 1 SEH CLH Set Half Carry Flag in SREG Clear Half Carry Flag in SREG H←1 H←0 H H 1 1 None 1 DATA TRANSFER INSTRUCTIONS MOV Rd, Rr Move Between Registers MOVW Rd, Rr Copy Register Word Rd ← Rr Rd+1:Rd ← Rr+1:Rr None 1 LDI Rd, K Load Immediate Rd ← K None 1 2 LD Rd, X Load Indirect Rd ← (X) None LD Rd, X+ Load Indirect and Post-Inc. Rd ← (X), X ← X + 1 None 2 LD Rd, - X Load Indirect and Pre-Dec. X ← X - 1, Rd ← (X) None 2 LD Rd, Y Load Indirect Rd ← (Y) None 2 LD Rd, Y+ Load Indirect and Post-Inc. Rd ← (Y), Y ← Y + 1 None 2 2 LD Rd, - Y Load Indirect and Pre-Dec. Y ← Y - 1, Rd ← (Y) None LDD Rd,Y+q Load Indirect with Displacement Rd ← (Y + q) None 2 LD Rd, Z Load Indirect Rd ← (Z) None 2 LD Rd, Z+ Load Indirect and Post-Inc. Rd ← (Z), Z ← Z+1 None 2 LD Rd, -Z Load Indirect and Pre-Dec. Z ← Z - 1, Rd ← (Z) None 2 2 LDD Rd, Z+q Load Indirect with Displacement Rd ← (Z + q) None LDS Rd, k Load Direct from SRAM Rd ← (k) None 2 ST X, Rr Store Indirect (X) ← Rr None 2 ST X+, Rr Store Indirect and Post-Inc. (X) ← Rr, X ← X + 1 None 2 ST - X, Rr Store Indirect and Pre-Dec. X ← X - 1, (X) ← Rr None 2 2 ST Y, Rr Store Indirect (Y) ← Rr None ST Y+, Rr Store Indirect and Post-Inc. (Y) ← Rr, Y ← Y + 1 None 2 ST - Y, Rr Store Indirect and Pre-Dec. Y ← Y - 1, (Y) ← Rr None 2 STD Y+q,Rr Store Indirect with Displacement (Y + q) ← Rr None 2 ST Z, Rr Store Indirect (Z) ← Rr None 2 ST Z+, Rr Store Indirect and Post-Inc. (Z) ← Rr, Z ← Z + 1 None 2 ST -Z, Rr Store Indirect and Pre-Dec. Z ← Z - 1, (Z) ← Rr None 2 STD Z+q,Rr Store Indirect with Displacement (Z + q) ← Rr None 2 STS k, Rr Store Direct to SRAM (k) ← Rr None 2 Load Program Memory R0 ← (Z) None 3 Load Program Memory Rd ← (Z) None 3 LPM LPM Rd, Z LPM Rd, Z+ ELPM ELPM Rd, Z Load Program Memory and Post-Inc Rd ← (Z), Z ← Z+1 None 3 Extended Load Program Memory R0 ← (RAMPZ:Z) None 3 Extended Load Program Memory Rd ← (RAMPZ:Z) None 3 18 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 Mnemonics ELPM Operands Rd, Z+ SPM Description Operation Flags #Clocks Extended Load Program Memory Rd ← (RAMPZ:Z), RAMPZ:Z ←RAMPZ:Z+1 None Store Program Memory (Z) ← R1:R0 None - Rd ← P None 1 3 IN Rd, P In Port OUT P, Rr Out Port P ← Rr None 1 PUSH Rr Push Register on Stack STACK ← Rr None 2 POP Rd Pop Register from Stack Rd ← STACK None 2 None 1 MCU CONTROL INSTRUCTIONS NOP No Operation SLEEP Sleep (see specific descr. for Sleep function) None 1 WDR BREAK Watchdog Reset Break (see specific descr. for WDR/timer) For On-chip Debug Only None None 1 N/A Note: EICALL and EIJMP do not exist in ATmega640/1280/1281. ELPM does not exist in ATmega640. 19 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 9. Ordering Information 9.1 ATmega640 Speed (MHz)(2) Power Supply 8 16 Notes: Ordering Code Package(1)(3) 1.8 - 5.5V ATmega640V-8AU ATmega640V-8AUR(4) ATmega640V-8CU ATmega640V-8CUR(4) 100A 100A 100C1 100C1 2.7 - 5.5V ATmega640-16AU ATmega640-16AUR(4) ATmega640-16CU ATmega640-16CUR(4) 100A 100A 100C1 100C1 Operation Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. See “Speed Grades” on page 369. 3. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. 4. Tape & Reel Package Type 100A 100-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP) 100C1 100-ball, Chip Ball Grid Array (CBGA) 20 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 9.2 ATmega1280 Speed (MHz)(2) Power Supply 8 16 Notes: Ordering Code Package(1)(3) 1.8V - 5.5V ATmega1280V-8AU ATmega1280V-8AUR(4) ATmega1280V-8CU ATmega1280V-8CUR(4) 100A 100A 100C1 100C1 2.7V - 5.5V ATmega1280-16AU ATmega1280-16AUR(4) ATmega1280-16CU ATmega1280-16CUR(4) 100A 100A 100C1 100C1 Operation Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. See “Speed Grades” on page 369. 3. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. 4. Tape & Reel Package Type 100A 100-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP) 100C1 100-ball, Chip Ball Grid Array (CBGA) 21 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 9.3 ATmega1281 Speed (MHz)(2) 8 16 Notes: Ordering Code Package(1)(3) 1.8 - 5.5V ATmega1281V-8AU ATmega1281V-8AUR(4) ATmega1281V-8MU ATmega1281V-8MUR(4) 64A 64A 64M2 64M2 2.7 - 5.5V ATmega1281-16AU ATmega1281-16AUR(4) ATmega1281-16MU ATmega1281-16MUR(4) 64A 64A 64M2 64M2 Power Supply Operation Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. See “Speed Grades” on page 369. 3. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. 4. Tape & Reel Package Type 64A 64-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP) 64M2 64-pad, 9mm × 9mm × 1.0mm Body, Quad Flat No-lead/Micro Lead Frame Package (QFN/MLF) 22 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 9.4 ATmega2560 Speed (MHz)(2) Power Supply 8 16 Notes: Ordering Code Package(1)(3) 1.8V - 5.5V ATmega2560V-8AU ATmega2560V-8AUR(4) ATmega2560V-8CU ATmega2560V-8CUR(4) 100A 100A 100C1 100C1 4.5V - 5.5V ATmega2560-16AU ATmega2560-16AUR(4) ATmega2560-16CU ATmega2560-16CUR(4) 100A 100A 100C1 100C1 Operation Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. See “Speed Grades” on page 369. 3. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. 4. Tape & Reel Package Type 100A 100-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP) 100C1 100-ball, Chip Ball Grid Array (CBGA) 23 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 9.5 ATmega2561 Speed (MHz)(2) Power Supply 8 16 Notes: Ordering Code Package(1)(3) 1.8V - 5.5V ATmega1281V-8AU ATmega1281V-8AUR(4) ATmega1281V-8MU ATmega1281V-8MUR(4) 64A 64A 64M2 64M2 4.5V - 5.5V ATmega1281-16AU ATmega1281-16AUR(4) ATmega1281-16MU ATmega1281-16MUR(4) 64A 64A 64M2 64M2 Operation Range Industrial (-40°C to 85°C) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. See “Speed Grades” on page 369. 3. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. 4. Tape & Reel Package Type 64A 64-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP) 64M2 64-pad, 9mm × 9mm × 1.0mm Body, Quad Flat No-lead/Micro Lead Frame Package (QFN/MLF) 24 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 10. Packaging Information 10.1 100A PIN 1 B PIN 1 IDENTIFIER E1 e E D1 D C 0°~7° A1 A2 A L COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-026, Variation AED. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.08mm maximum. SYMBOL MIN NOM MAX A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 15.75 16.00 16.25 D1 13.90 14.00 14.10 E 15.75 16.00 16.25 E1 13.90 14.00 14.10 B 0.17 – 0.27 C 0.09 – 0.20 L 0.45 – 0.75 e NOTE Note 2 Note 2 0.50 TYP 2010-10-20 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 100A, 100-lead, 14 x 14mm Body Size, 1.0mm Body Thickness, 0.5mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. 100A REV. D 25 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 10.2 100C1 0.12 Z E Marked A1 Identifier SIDE VIEW D A TOP VIEW A1 Øb e A1 Corner 0.90 TYP 10 9 8 7 6 5 4 3 2 1 A 0.90 TYP B C D COMMON DIMENSIONS (Unit of Measure = mm) E D1 F e SYMBOL MIN NOM MAX H A 1.10 – 1.20 I A1 0.30 0.35 0.40 D 8.90 9.00 9.10 E 8.90 9.00 9.10 G J E1 BOTTOM VIEW D1 7.10 7.20 7.30 E1 7.10 7.20 7.30 Øb 0.35 0.40 0.45 e NOTE 0.80 TYP 5/25/06 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 100C1, 100-ball, 9 x 9 x 1.2 mm Body, Ball Pitch 0.80 mm Chip Array BGA Package (CBGA) DRAWING NO. 100C1 REV. A 26 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 10.3 64A PIN 1 B e PIN 1 IDENTIFIER E1 E D1 D C 0°~7° A1 A2 A L COMMON DIMENSIONS (Unit of measure = mm) Notes: 1.This package conforms to JEDEC reference MS-026, Variation AEB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10mm maximum. SYMBOL MIN NOM MAX A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 15.75 16.00 16.25 D1 13.90 14.00 14.10 E 15.75 16.00 16.25 E1 13.90 14.00 14.10 B 0.30 – 0.45 C 0.09 – 0.20 L 0.45 – 0.75 e NOTE Note 2 Note 2 0.80 TYP 2010-10-20 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 64A, 64-lead, 14 x 14mm Body Size, 1.0mm Body Thickness, 0.8mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. REV. 64A C 27 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 10.4 64M2 D Marked pin# 1 I D E C SEATING PLANE A1 TOP VIEW A3 A K 0.08 C L Pin #1 Corner D2 1 2 3 SIDE VIEW Pin #1 Triangle Option A COMMON DIMENSIONS (Unit of measure = mm) E2 Option B Pin #1 Chamfer (C 0.30) SYMBOL MIN NOM MAX A 0.80 0.90 1.00 A1 – 0.02 0.05 A3 K Option C b e Pin #1 Notch (0.20 R) BOTTOM VIEW 0.20 REF b 0.18 0.25 0.30 D 8.90 9.00 9.10 D2 7.50 7.65 7.80 E 8.90 9.00 9.10 E2 7.50 7.65 7.80 e Notes: 1. JEDEC Standard MO-220, (SAW Singulation) fig . 1, VMMD. 2. Dimension and tolerance conform to ASMEY14.5M-1994. NOTE 0.50 BSC L 0.35 0.40 0.45 K 0.20 0.27 0.40 2010-10-20 R TITLE 2325 Orchard Parkway 64M2, 64-pad, 9 x 9 x 1.0mm Bod y, Lead Pitch 0.50mm , San Jose, CA 95131 7.65mm Exposed Pad, Micro Lead Frame Package (MLF) DRAWING NO. 64M2 REV. E 28 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 11. Errata 11.1 ATmega640 rev. B • Inaccurate ADC conversion in differential mode with 200× gain • High current consumption in sleep mode 1. Inaccurate ADC conversion in differential mode with 200× gain With AVCC <3.6V, random conversions will be inaccurate. Typical absolute accuracy may reach 64 LSB. Problem Fix/Workaround None. 2. High current consumption in sleep mode If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. 11.2 ATmega640 rev. A • Inaccurate ADC conversion in differential mode with 200× gain • High current consumption in sleep mode 1. Inaccurate ADC conversion in differential mode with 200× gain With AVCC <3.6V, random conversions will be inaccurate. Typical absolute accuracy may reach 64 LSB. Problem Fix/Workaround None. 2. High current consumption in sleep mode If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. 11.3 ATmega1280 rev. B • Inaccurate ADC conversion in differential mode with 200× gain • High current consumption in sleep mode 1. Inaccurate ADC conversion in differential mode with 200× gain With AVCC <3.6V, random conversions will be inaccurate. Typical absolute accuracy may reach 64 LSB. 29 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 Problem Fix/Workaround None. 2. High current consumption in sleep mode If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. 11.4 ATmega1280 rev. A • Inaccurate ADC conversion in differential mode with 200× gain • High current consumption in sleep mode 1. Inaccurate ADC conversion in differential mode with 200× gain With AVCC <3.6V, random conversions will be inaccurate. Typical absolute accuracy may reach 64 LSB. Problem Fix/Workaround None. 2. High current consumption in sleep mode If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. 11.5 ATmega1281 rev. B • Inaccurate ADC conversion in differential mode with 200× gain • High current consumption in sleep mode 1. Inaccurate ADC conversion in differential mode with 200× gain With AVCC <3.6V, random conversions will be inaccurate. Typical absolute accuracy may reach 64 LSB. Problem Fix/Workaround None. 2. High current consumption in sleep mode If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. 30 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 11.6 ATmega1281 rev. A • Inaccurate ADC conversion in differential mode with 200× gain • High current consumption in sleep mode 1. Inaccurate ADC conversion in differential mode with 200× gain With AVCC <3.6V, random conversions will be inaccurate. Typical absolute accuracy may reach 64 LSB. Problem Fix/Workaround None. 2. High current consumption in sleep mode If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. 11.7 ATmega2560 rev. F Not sampled. 11.8 ATmega2560 rev. E No known errata. 11.9 ATmega2560 rev. D Not sampled. 11.10 ATmega2560 rev. C • High current consumption in sleep mode 1. High current consumption in sleep mode If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. 11.11 ATmega2560 rev. B Not sampled. 31 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 11.12 ATmega2560 rev. A • • • • • • 1. Non-Read-While-Write area of flash not functional Part does not work under 2.4 volts Incorrect ADC reading in differential mode Internal ADC reference has too low value IN/OUT instructions may be executed twice when Stack is in external RAM EEPROM read from application code does not work in Lock Bit Mode 3 Non-Read-While-Write area of flash not functional The Non-Read-While-Write area of the flash is not working as expected. The problem is related to the speed of the part when reading the flash of this area. Problem Fix/Workaround - Only use the first 248K of the flash. - If boot functionality is needed, run the code in the Non-Read-While-Write area at maximum 1/4th of the maximum frequency of the device at any given voltage. This is done by writing the CLKPR register before entering the boot section of the code. 2. Part does not work under 2.4 volts The part does not execute code correctly below 2.4 volts. Problem Fix/Workaround Do not use the part at voltages below 2.4 volts. 3. Incorrect ADC reading in differential mode The ADC has high noise in differential mode. It can give up to 7 LSB error. Problem Fix/Workaround Use only the 7 MSB of the result when using the ADC in differential mode. 4. Internal ADC reference has too low value The internal ADC reference has a value lower than specified. Problem Fix/Workaround - Use AVCC or external reference. - The actual value of the reference can be measured by applying a known voltage to the ADC when using the internal reference. The result when doing later conversions can then be calibrated. 5. IN/OUT instructions may be executed twice when Stack is in external RAM If either an IN or an OUT instruction is executed directly before an interrupt occurs and the stack pointer is located in external ram, the instruction will be executed twice. In some cases this will cause a problem, for example: - If reading SREG it will appear that the I-flag is cleared. - If writing to the PIN registers, the port will toggle twice. - If reading registers with interrupt flags, the flags will appear to be cleared. 32 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 Problem Fix/Workaround There are two application work-arounds, where selecting one of them, will be omitting the issue: - Replace IN and OUT with LD/LDS/LDD and ST/STS/STD instructions. - Use internal RAM for stack pointer. 6. EEPROM read from application code does not work in Lock Bit Mode 3 When the Memory Lock Bits LB2 and LB1 are programmed to mode 3, EEPROM read does not work from the application code. Problem Fix/Workaround Do not set Lock Bit Protection Mode 3 when the application code needs to read from EEPROM. 11.13 ATmega2561 rev. F Not sampled. 11.14 ATmega2561 rev. E No known errata. 11.15 ATmega2561 rev. D Not sampled. 11.16 ATmega2561 rev. C • High current consumption in sleep mode. 1. High current consumption in sleep mode If a pending interrupt cannot wake the part up from the selected sleep mode, the current consumption will increase during sleep when executing the SLEEP instruction directly after a SEI instruction. Problem Fix/Workaround Before entering sleep, interrupts not used to wake the part from the sleep mode should be disabled. 11.17 ATmega2561 rev. B Not sampled. 11.18 ATmega2561 rev. A • • • • • • Non-Read-While-Write area of flash not functional Part does not work under 2.4 Volts Incorrect ADC reading in differential mode Internal ADC reference has too low value IN/OUT instructions may be executed twice when Stack is in external RAM EEPROM read from application code does not work in Lock Bit Mode 3 33 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 1. Non-Read-While-Write area of flash not functional The Non-Read-While-Write area of the flash is not working as expected. The problem is related to the speed of the part when reading the flash of this area. Problem Fix/Workaround - Only use the first 248K of the flash. - If boot functionality is needed, run the code in the Non-Read-While-Write area at maximum 1/4th of the maximum frequency of the device at any given voltage. This is done by writing the CLKPR register before entering the boot section of the code. 2. Part does not work under 2.4 volts The part does not execute code correctly below 2.4 volts. Problem Fix/Workaround Do not use the part at voltages below 2.4 volts. 3. Incorrect ADC reading in differential mode The ADC has high noise in differential mode. It can give up to 7 LSB error. Problem Fix/Workaround Use only the 7 MSB of the result when using the ADC in differential mode. 4. Internal ADC reference has too low value The internal ADC reference has a value lower than specified. Problem Fix/Workaround - Use AVCC or external reference. - The actual value of the reference can be measured by applying a known voltage to the ADC when using the internal reference. The result when doing later conversions can then be calibrated. 5. IN/OUT instructions may be executed twice when Stack is in external RAM If either an IN or an OUT instruction is executed directly before an interrupt occurs and the stack pointer is located in external ram, the instruction will be executed twice. In some cases this will cause a problem, for example: - If reading SREG it will appear that the I-flag is cleared. - If writing to the PIN registers, the port will toggle twice. - If reading registers with interrupt flags, the flags will appear to be cleared. Problem Fix/Workaround There are two application workarounds, where selecting one of them, will be omitting the issue: - Replace IN and OUT with LD/LDS/LDD and ST/STS/STD instructions. - Use internal RAM for stack pointer. 6. EEPROM read from application code does not work in Lock Bit Mode 3 When the Memory Lock Bits LB2 and LB1 are programmed to mode 3, EEPROM read does not work from the application code. 34 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 Problem Fix/Workaround Do not set Lock Bit Protection Mode 3 when the application code needs to read from EEPROM. 35 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 12. Datasheet Revision History Please note that the referring page numbers in this section are referring to this document.The referring revision in this section are referring to the document revision. 12.1 Rev. 2549P-10/2012 1. 2. 3. 12.2 Rev. 2549O-05/12 1. 2. 3. 12.3 The datasheet changed status from Preliminary to Complete. Removed “Preliminary” from the front page. Replaced Figure 10-3 on page 46 by a new one. Updated the last page to include the new address for Atmel Japan site. Rev. 2549N-05/11 1. 2. 3. 4. 5. 6. 7. 12.4 Replaced drawing in 10.4 “64M2” on page 28. Former page 439 has been deleted as the content of this page did not belong there (same page as the last page). Some small correction made in the setup. Added Atmel QTouch Library Support and QTouch Sensing Capablity Features Updated Cross-reference in “Bit 5, 2:0 - WDP3:0: Watchdog Timer Prescaler 3, 2, 1 and 0” on page 68 Updated Assembly codes in section “USART Initialization” on page 210 Added “Standard Power-On Reset” on page 372. Added “Enhanced Power-On Reset” on page 373. Updated Figure 32-13 on page 393 Updated “Ordering Information” on page 20 to include Tape & Reel devices. Rev. 2549M-09/10 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Updated typos in Figure 26-9 on page 285 and in Figure 26-10 on page 285. Note is added below Table 1-1 on page 3. The values for “typical characteristics” in Table 31-9 on page 377 and Table 31-10 on page 378, has been rounded. Units for tRST and tBOD in Table 31-3 on page 372 have been changed from “ns” to “µs”. The figure text for Table 31-2 on page 371 has been changed. Text in first column in Table 30-3 on page 336 has been changed from “Fuse Low Byte” to “Extended Fuse Byte”. The text in “Power Reduction Register” on page 54 has been changed. The value of the inductor in Figure 26-9 on page 285 and Figure 26-10 on page 285 has been changed to 10 µH. “Port A” has been changed into “Port K” in the first paragraph of “Features” on page 275. Minimum wait delay for tWD_EEPROM in Table 30-16 on page 351 has been changed from 9.0ms to 3.6ms Dimension A3 is added in “64M2” on page 28. Several cross-references are corrected. 36 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 13. 14. 15. 12.5 Rev. 2549L-08/07 1. 2. 3. 4. 5. 6. 7. 8. 9. 12.6 Updated note in Table 10-11 on page 47. Updated Table 10-3 on page 43, Table 10-5 on page 44, Table 10-9 on page 47. Updated typos in “DC Characteristics” on page 367 Updated “Clock Characteristics” on page 371 Updated “External Clock Drive” on page 371. Added “System and Reset Characteristics” on page 372. Updated “SPI Timing Characteristics” on page 375. Updated “ADC Characteristics – Preliminary Data” on page 377. Updated ordering code in “ATmega640” on page 20. Rev. 2549K-01/07 1. 2. 3. 4. 5. 6: 7. 8. 9. 10. 12.7 “COM0A1:0” on page 130 is corrected to “COM0B1:0”. Corrected some Figure and Table numbering. Updated Section 10.6 “Low Frequency Crystal Oscillator” on page 45. Updated Table 1-1 on page 3. Updated “Pin Descriptions” on page 7. Updated “Stack Pointer” on page 16. Updated “Bit 1 – EEPE: EEPROM Programming Enable” on page 36. Updated Assembly code example in “Thus, when the BOD is not enabled, after setting the ACBG bit or enabling the ADC, the user must always allow the reference to start up before the output from the Analog Comparator or ADC is used. To reduce power consumption in Power-down mode, the user can avoid the three conditions above to ensure that the reference is turned off before entering Power-down mode.” on page 63. Updated “EIMSK – External Interrupt Mask Register” on page 115. Updated Bit description in “PCIFR – Pin Change Interrupt Flag Register” on page 116. Updated code example in “USART Initialization” on page 210. Updated Figure 26-8 on page 284. Updated “DC Characteristics” on page 367. Rev. 2549J-09/06 1. 2. 3. 4. 5. 6. Updated “” on page 46. Updated code example in “Moving Interrupts Between Application and Boot Section” on page 109. Updated “Timer/Counter Prescaler” on page 186. Updated “Device Identification Register” on page 303. Updated “Signature Bytes” on page 338. Updated “Instruction Set Summary” on page 17. 37 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 12.8 Rev. 2549I-07/06 1. 2. 3. 12.9 Added “Data Retention” on page 11. Updated Table 16-3 on page 129, Table 16-6 on page 130, Table 16-8 on page 131, Table 17-2 on page 148, Table 17-4 on page 159, Table 17-5 on page 160, Table 20-3 on page 187, Table 20-6 on page 188 and Table 20-8 on page 189. Updated “Fast PWM Mode” on page 150. Rev. 2549H-06/06 1. 2. 3. Updated “” on page 46. Updated “OSCCAL – Oscillator Calibration Register” on page 50. Added Table 31-1 on page 371. 12.10 Rev. 2549G-06/06 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Updated “Features” on page 1. Added Figure 1-2 on page 3, Table 1-1 on page 3. Updated “” on page 46. Updated “Power Management and Sleep Modes” on page 52. Updated note for Table 12-1 on page 68. Updated Figure 26-9 on page 285 and Figure 26-10 on page 285. Updated “Setting the Boot Loader Lock Bits by SPM” on page 324. Updated “Ordering Information” on page 20. Added Package information “100C1” on page 26. Updated “Errata” on page 29. 12.11 Rev. 2549F-04/06 1. 2. 3. 4. Updated Figure 9-3 on page 31, Figure 9-4 on page 31 and Figure 9-5 on page 32. Updated Table 20-2 on page 187 and Table 20-3 on page 187. Updated Features in “ADC – Analog to Digital Converter” on page 275. Updated “Fuse Bits” on page 336. 12.12 Rev. 2549E-04/06 1. 2. 3. 4. 5. 5. 6. Updated “Features” on page 1. Updated Table 12-1 on page 62. Updated note for Table 12-1 on page 62. Updated “Bit 6 – ACBG: Analog Comparator Bandgap Select” on page 273. Updated “Prescaling and Conversion Timing” on page 278. Updated “Maximum speed vs. VCC” on page 373. Updated “Ordering Information” on page 20. 38 2549PS–AVR–10/2012 ATmega640/1280/1281/2560/2561 12.13 Rev. 2549D-12/05 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Advanced Information Status changed to Preliminary. Changed number of I/O Ports from 51 to 54. Updatet typos in “TCCR0A – Timer/Counter Control Register A” on page 129. Updated Features in “ADC – Analog to Digital Converter” on page 275. Updated Operation in“ADC – Analog to Digital Converter” on page 275 Updated Stabilizing Time in “Changing Channel or Reference Selection” on page 282. Updated Figure 26-1 on page 276, Figure 26-9 on page 285, Figure 26-10 on page 285. Updated Text in “ADCSRB – ADC Control and Status Register B” on page 290. Updated Note for Table 4 on page 43, Table 13-15 on page 86, Table 26-3 on page 289 and Table 26-6 on page 295. Updated Table 31-9 on page 377 and Table 31-10 on page 378. Updated “Filling the Temporary Buffer (Page Loading)” on page 323. Updated “Typical Characteristics” on page 385. Updated “Packaging Information” on page 25. Updated “Errata” on page 29. 12.14 Rev. 2549C-09/05 1. 2. 3. 4. 5. 6. 7. 8. Updated Speed Grade in section “Features” on page 1. Added “Resources” on page 11. Updated “SPI – Serial Peripheral Interface” on page 195. In Slave mode, low and high period SPI clock must be larger than 2 CPU cycles. Updated “Bit Rate Generator Unit” on page 247. Updated “Maximum speed vs. VCC” on page 373. Updated “Ordering Information” on page 20. Updated “Packaging Information” on page 25. Package 64M1 replaced by 64M2. Updated “Errata” on page 29. 12.15 Rev. 2549B-05/05 1. 2. 3. 4. JTAG ID/Signature for ATmega640 updated: 0x9608. Updated Table 13-7 on page 81. Updated “Serial Programming Instruction set” on page 352. Updated “Errata” on page 29. 12.16 Rev. 2549A-03/05 1. Initial version. 39 2549PS–AVR–10/2012 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: (+1)(408) 441-0311 Fax: (+1)(408) 487-2600 www.atmel.com Atmel Asia Limited Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel: (+852) 2245-6100 Fax: (+852) 2722-1369 Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel: (+49) 89-31970-0 Fax: (+49) 89-3194621 Atmel Japan 16F, Shin-Osaki Kangyo Bldg. 1-6-8 Osaki Shinagawa-ku Tokyo 141-0032 JAPAN Tel: (+81)(3) 6417-0300 Fax: (+81)(3) 6417-0370 © 2012 Atmel Corporation. All rights reserved. Atmel ®, Atmel logo and combinations thereof, AVR ®, QTouch ®, QMatrix®, AVR Studio ® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Windows ® and others are registered trademarks of Microsoft Corporation in U.S. and other countries. Other terms and product names may be trademarks of others. Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. 2549PS–AVR–10/2012