Emcore EOS-6000 Optical a/b switch Datasheet

PRELIMINARY DATA SHEET | JULY 7, 2008
Applications
EOS-6000 Optical A/B Switch
Fiber Optical Protection Switching
Redundant ring architectures
FTTx networks
Features
Automatic, manual and remote
switching
Auto-switching time less than 25ms
SNMP Control Interface
Front Panel LED indicators
1 RU rack-mount enclosure with choice
of AC or DC power supply
The Model EOS-6000 Optical A/B Switch series product line is a
high performance solution for network protection and optical
redundancy. Packaged in a convenient 1RU housing, this line of
optical switches provides an automatic or manual fiber switching
function to protect the network from inadvertent service outages
due to up-stream optical signal degradation. Each fiber’s optical
signal power level is continuously monitored, as is an adjustable
optical trip threshold for each channel. If the primary fiber’s optical
signal power level falls below the desired optical trip threshold, the
unit automatically switches to the secondary fiber, thus eliminating
the need for intervention of a system operator. The EOS-6000 is
capable of manual switching or can be switched remotely via
SNMP adding optical protection to many system applications.
The EOS-6000 series is designed as a low power, cost effective,
high performance switching solution for applications that demand
reliable and rapid response to changing network conditions.
Figure 1: Redundant Path Configuration for CATV Broadcast
1 of 3
For more information on this and other products:
Contact Sales at EMCORE 626-293-3400, or visit www.emcore.com.
EOS-6000 Optical A/B Switch
PRELIMINARY DATA SHEET | JULY 7, 2008
Optical Characteristics
PROPERTY
Operating Wave Length
Insertion Loss
Return Loss
Polarization Dependent
Loss
Repeatability
Isolation
Input Optical Power
Switching Time
MIN.
UNITS
nm
TYP.
MAX.
1310 +/- 10 or 1550+/-20
dB
dB
dB
55
dB
dB
dBm
ms
1.0
60
0.06
1.3
+/-0.01
-60
+/-0.02
-50
24
25
0.1
General and Mechanical Specifications
PROPERTY
Switching Threshold
Switching Mode
Optical Connector
Monitoring Interfaces
REQUIREMENT
20 dB range – see ordering info
Auto, Manual, remote
SC/APC
100 Base-T Ethernet
Rear Panel RS-232 interface
LED Indicators
0°C to 50°C
Operating Temperature
Storage Temperature
Agency Listings
-25°C to 65°C
FCC: Subpart B. Part 15, class “A” Unintentional
Radiators
Power Consumption
5W
Supply Range
(VAC)
(VDC)
Dimensions
COMMENTS
Settable within range
Other styles available
SNMP V1
Reserved for Factory Use
Power, Main, Backup, and Output Indicators
Maximum
85 to 240 VAC, 50/60 Hz
36 - 60 VDC
430x300x44mm
2 of 3
EMCORE Broadband
2015 West Chestnut Street
Alhambra, California 91803-1542
Tel: 626-293-3400
Fax: 626-293-3428
www.emcore.com
Copyright 2008. EMCORE Corporation
EOS-6000 Optical A/B Switch
PRELIMINARY DATA SHEET | JULY 7, 2008
Model Number Information (note 1)
Operating
Wavelenghth
3 – 1310nm
5 – 1550nm
Optics
1–
SC/APC
2–
FC/APC
3–
SC/UPC
4–
FC/UPC
Power
Supply
1 – AC
Switching
Threshold range
1 – [-30, -10] dBm
Emcore Logo
2 – DC
2 – [-20, 0] dBm
2 – Yes
0 – No
3 – [-10, 10] dBm
4 – [0, 20] dBm
Note 1: Not all configurations are available - contact factory.
Example: 6000-0S5-1232
1550nm, SC/APC connectors, DC power supply, -10 to + 10 dBm input range, Emcore Logo.
Information contained herein is deemed to be reliable and accurate as of issue date. EMCORE reserves the right to change the design or specifications of
the product at any time without notice. EMCORE, and the EMCORE logo are trademarks of EMCORE Corporation.
3 of 3
EMCORE Broadband
2015 West Chestnut Street
Alhambra, California 91803-1542
Tel: 626-293-3400
Fax: 626-293-3428
www.emcore.com
Copyright 2008. EMCORE Corporation
Similar pages