Capacitors with 4 Snap-In Terminals and Solder Pins B43510 Miniaturized – 85 °C B43520 B43510, B43520 Long-life grade capacitors Applications ■ Frequency converters ■ Switch-mode power supplies in industrial and consumer electronics ■ Uninterruptible power supplies Features ■ ■ ■ ■ KAL0409-D Extremely small dimensions High ripple current capability Many different case sizes Pinning ensures correct insertion B43510 Construction ■ Charge-discharge proof, polar ■ Aluminum case, fully insulated ■ Overload protection by preset break point in case Terminals ■ 4 snap-in terminals (6,3 mm and 4,5 mm length) ■ Solder pin mounting on printed circuit boards, pins fit standardized spacings on PCB 178 10/02 B43520 B43510 / B43520 Miniaturized – 85 °C Specifications and characteristics in brief Rated voltage UR 385 … 500 VDC Surge voltage US 1,1 · UR Rated capacitance CR 390 … 2 700 µF Capacitance tolerance Leakage current IL ± 20 % M (5 min, 20 °C) C R U R 0,7 I L ≤ 0,3 µA ⋅ æè ------- ⋅ ------- öø + 4 µA µF V Self-inductance ESL Approx. 20 nH Useful life 85 °C; UR; I~R 40 °C; UR; 1,1 · I~R Requirements: > 5 000 h > 250 000 h ∆C/C ESR IL ≤ ± 30 % of initial value ≤ 3 times initial specified limit ≤ initial specified limit Failure percentage: ≤ 1 % Failure rate: ≤ 40 fit (≤ 40 · 10 –9/h) (for definiton “fit”, refer to chapter “Quality”, page 62) Voltage endurance test Post test requirements: Detail specification ∆C/C ≤ ± 10 % of initial value ESR ≤ 1,3 times initial specified limit IL ≤ initial specified limit To IEC 60068-2-6, test Fc: displacement amplitude 0,35 mm, frequency range 10 … 55 Hz, acceleration max. 5 g, duration 3 × 2 h To IEC 60068-1: UR ≤ 400 VDC: 40/085/56 (– 40 °C/+ 85 °C/56 days damp heat test) UR > 400 VDC: 25/085/56 (– 25 °C/+ 85 °C/56 days damp heat test) Similar to CECC 30301-805 Sectional specification IEC 60384-4 85 °C; UR Vibration resistance IEC climatic category 2 000 h 179 10/02 B43510 / B43520 Miniaturized – 85 °C Dimensional drawings B43510, 4 snap-in terminals Mounting holes Montagelochung 30 ±3 30 30 PluspolPlus pole marking Kennzeichnung d 0´ Minus pole marking Minuspol Kennzeichnung 2±0,1 6,3±1 6,3±1 l l 22,5±0,1 _ 0,1 0,8 +0,2 _ 0,1 0,8 +0,2 1,5±0,2 1,5±0,2 0,8 0,8 KAL0401-H KAL0401-H Standard snap-in terminals: length (6,3 ± 1) mm. Also available with a length of (4,5 – 1) mm. For ordering example cf. page 181 B43520, solder pins Dimensions (mm) Approx. d +1 l ± 2 lmax weight (g) Packing units (pieces) 35 35 35 35 35 50 60 70 80 100 54 64 74 84 104 63 76 88 101 126 60 36 36 36 36 40 40 40 40 40 40 40 50 60 70 80 100 44 54 64 74 84 104 71 89 107 125 143 178 33 33 33 33 33 33 45 45 45 45 45 45 40 50 60 70 80 100 — — — — — — 90 113 136 158 181 226 28 28 28 28 28 28 d = 35 mm d = 40 mm +1 + 1 2 4 1) – – Mounting holes (view ontovonsolder side) Montagelochung (Ansicht der Lötseite) 20±0,1 ø1,3+0,1 +1 15±0,1 1) Permissible range of positions for pole identification marks 3 ø1,3+0,1 +1 4 20±0,1 7,5±0,1 – – 2 17,5±0,1 l 3 l max 15 d 1) 2 3 17,5±0,1 4,5±0,5 15 3 0,8x1,1 _ 0,1 KAL0400-9 Pole markings: Plus: +; Minus: – All pin holes must be drilled into the PC-board, since the unconnected pins serve as mountings. These pins must be soldered to isolated pads or pads with the same potential as the negative pole (solder pin and 4 snap-in terminals). 180 10/02 Packing B43510 / B43520 Miniaturized – 85 °C Packing of 4 snap-in terminals and solder pins For ecological reasons the packing is pure cardboard. Ordering codes 4 snap-in terminals Version Identification in 3rd block of ordering code Standard terminals (6,3 ± 1) mm M000 Short terminals (4,5 −1) mm M007 181 10/02 B43510 / B43520 Miniaturized – 85 °C Overview of available types UR (VDC) 385 CR (µF) Case dimensions d × l (mm) 400 420 450 500 390 35 × 60 470 35 × 70 35 × 70 40 × 60 35 × 60 560 680 820 35 × 40 × 35 × 40 × 50 50 60 50 1 000 35 × 70 40 × 60 1 200 35 × 80 40 × 70 1 500 40 × 80 45 × 60 1 800 40 × 100 45 × 70 35 × 40 × 35 × 40 × 60 50 60 50 35 × 70 40 × 60 45 × 50 35 × 100 40 × 70 35 × 100 40 × 80 45 × 70 40 × 100 45 × 80 2 200 40 × 100 45 × 100 2 700 45 × 100 45 × 100 35 × 40 × 35 × 40 × 70 50 80 60 35 × 100 40 × 70 35 × 100 40 × 80 35 × 80 40 × 60 35 × 100 40 × 70 45 × 60 40 × 100 45 × 70 40 × 70 40 × 80 45 × 70 45 × 100 40 × 100 45 × 70 40 × 100 45 × 80 45 × 100 40 × 100 45 × 80 45 × 100 60 50 70 60 35 × 40 × 35 × 40 × 45 × 100 The capacitance and voltage ratings listed above are available in different cases upon request. Other voltage and capacitance ratings are also available upon request. Capacitors with solder pins are only available in 35 and 40 mm case diameters. 182 10/02 B43510 / B43520 Miniaturized – 85 °C Technical data and ordering codes UR VDC 385 400 I ~R 100 Hz 85 °C A Ordering code 1) 7,7 8,1 3,5 3,7 B435*0A3687M000 B435*0B3687M000 130 130 9,0 8,9 4,1 4,0 B435*0A3827M000 B435*0B3827M000 130 130 110 110 10,6 10,5 4,8 4,8 B435*0A3108M000 B435*0B3108M000 35 × 80 40 × 70 110 110 90 90 12,3 12,2 5,6 5,5 B435*0A3128M000 B435*0B3128M000 1500 1500 40 × 80 45 × 60 90 90 70 70 14,4 12,9 6,5 5,9 B435*0A3158M000 B43510B3158M000 1800 1800 40 × 100 45 × 70 80 80 60 60 17,2 14,9 7,8 6,8 B435*0A3188M000 B43510B3188M000 2200 2700 40 × 100 45 × 100 60 50 50 40 19,1 21,1 8,7 9,6 B435*0A3228M000 B43510A3278M000 CR 100 Hz 20 °C µF Case dimensions d×l mm ESRmax 100 Hz 20 °C mΩ Zmax 10 kHz 20 °C mΩ 680 680 35 × 50 40 × 50 190 190 150 150 820 820 35 × 60 40 × 50 160 160 1000 1000 35 × 70 40 × 60 1200 1200 I~max 100 Hz 40 °C A * 1 = 4 snap-in 2 = solder pin 680 35 × 60 190 150 8,2 3,7 B435*0A9687M000 680 40 × 50 190 150 8,1 3,7 B435*0B9687M000 820 820 35 × 60 40 × 50 160 160 130 130 9,0 8,9 4,1 4,0 B435*0A9827M000 B435*0B9827M000 1000 35 × 70 130 110 10,6 4,8 B435*0A9108M000 1000 40 × 60 130 110 10,5 4,8 B435*0B9108M000 1000 1200 45 × 50 35 × 100 130 110 110 90 9,9 13,5 4,5 6,1 B43510C9108M000 B435*0A9128M000 1200 1500 1500 40 × 70 35 × 100 40 × 80 110 90 90 90 70 70 12,2 15,0 14,4 5,5 6,8 6,5 B435*0B9128M000 B435*0A9158M000 B435*0B9158M000 1500 1800 45 × 70 40 × 100 90 80 70 60 13,6 17,2 6,2 7,8 B43510C9158M000 B435*0A9188M000 1800 45 × 80 80 60 15,7 7,2 B43510B9188M000 2200 45 × 100 60 50 19,0 8,6 B43510A9228M000 2700 45 × 100 50 40 21,1 9,6 B43510A9278M000 Capacitors with solder pins are only available in 35 and 40 mm case diameters. 1) For capacitors with short 4 snap-in terminals, see page 181. 183 10/02 B43510 / B43520 Miniaturized – 85 °C Technical data and ordering codes UR VDC 420 450 CR 100 Hz 20 °C µF Case dimensions d×l mm ESRmax 100 Hz 20 °C mΩ Zmax 10 kHz 20 °C mΩ 680 680 35 × 60 40 × 50 300 300 240 240 820 820 35 × 70 40 × 60 250 250 200 200 I ~R 100 Hz 85 °C A Ordering code 1) 8,2 8,1 3,7 3,7 B435*0A0687M000 B435*0B0687M000 9,6 9,5 4,4 4,3 B435*0A0827M000 B435*0B0827M000 I~max 100 Hz 40 °C A * 1 = 4 snap-in 2 = solder pin 1000 35 × 80 200 160 11,2 5,1 B435*0A0108M000 1000 40 × 60 200 160 10,5 4,8 B435*0B0108M000 B435*0A0128M000 1200 40 × 70 170 140 12,2 5,5 1500 40 × 100 140 110 15,7 7,2 B435*0A0158M000 1500 1800 45 × 70 40 × 100 140 120 110 90 13,6 17,2 6,2 7,8 B43510B0158M000 B435*0A0188M000 1800 560 45 × 80 35 × 60 120 360 90 290 15,7 7,5 7,2 3,4 B43510B0188M000 B435*0A5567M000 680 680 35 × 70 40 × 50 300 300 240 240 8,7 8,1 4,0 3,7 B435*0A5687M000 B435*0B5687M000 820 820 35 × 80 40 × 60 250 250 200 200 10,1 9,5 4,6 4,3 B435*0A5827M000 B435*0B5827M000 1000 1000 35 × 100 40 × 70 200 200 160 160 12,3 11,1 5,6 5,1 B435*0A5108M000 B435*0B5108M000 1000 45 × 60 200 160 10,5 4,8 B43510C5108M000 1200 40 × 80 170 140 12,8 5,8 B435*0A5128M000 B43510B5128M000 1200 45 × 70 170 140 12,2 5,5 1500 40 × 100 140 110 15,7 7,2 B435*0A5158M000 1500 1800 2200 45 × 80 45 × 100 45 × 100 140 120 100 110 90 80 14,4 17,2 19,0 6,5 7,8 8,6 B43510B5158M000 B43510A5188M000 B43510A5228M000 Capacitors with solder pins are only available in 35 and 40 mm case diameters. 1) For capacitors with short 4 snap-in terminals, see page 181. 184 10/02 B43510 / B43520 Miniaturized – 85 °C Technical data and ordering codes UR VDC 500 I ~R 100 Hz 85 °C A Ordering code 1) 4,1 4,8 1,9 2,2 B435*0A6397M000 B435*0A6477M000 290 290 5,2 5,1 2,4 2,3 B435*0A6567M000 B435*0B6567M000 300 240 6,6 3,0 B435*0A6687M000 300 240 6,0 2,7 B435*0B6687M000 35 × 100 250 200 7,3 3,3 B435*0A6827M000 40 × 80 250 200 7,0 3,2 B435*0B6827M000 1000 1000 40 × 100 45 × 70 200 200 160 160 8,4 7,3 3,8 3,3 B435*0A6108M000 B43510B6108M000 1200 1500 45 × 100 45 × 100 170 140 140 110 9,2 10,3 4,2 4,7 B43510A6128M000 B43510A6158M000 CR 100 Hz 20 °C µF Case dimensions d×l mm ESRmax 100 Hz 20 °C mΩ Zmax 10 kHz 20 °C mΩ 390 470 35 × 60 35 × 70 520 430 410 340 560 560 35 × 70 40 × 60 360 360 680 35 × 100 680 40 × 70 820 820 I~max 100 Hz 40 °C A * 1 = 4 snap-in 2 = solder pin Capacitors with solder pins are only available in 35 and 40 mm case diameters. 1) For capacitors with short 4 snap-in terminals, see page 181. 185 10/02 B43510 / B43520 Miniaturized – 85 °C Useful life depending on ambient temperature TA under ripple current operating conditions 1) KAL0568-J 2,5 Ι~ Ι ~R B43510/520 2,0 1,5 0 40 50 60 70 5 000 h 10 000 h 20 000 h 50 000 h 100 000 h 0,5 250 000 h 1,0 80 ˚C 90 TA Frequency characteristics of ESR Typical behavior Frequency factor of permissible ripple current I~ versus frequency f KAL0569-S 1,5 Ι ~f B43510/520 Ι ~100 Hz KAL0570-V 2,5 ESR f ESR 100 Hz B43510/520 2,0 1,3 1,2 1,5 <_ 400 V > 400 V 1,1 1,0 1,0 20 ˚C 0,9 0,5 > 60 ˚C 0,8 0,7 1 10 10 2 10 3 Hz f 0 1 10 10 4 5 10 2 1) Refer to page 40 for an explanation on how to interpret the useful life graphs. 186 10/02 5 10 3 Hz 10 4 f B43510 / B43520 Miniaturized – 85 °C Impedance Z at f = 10 kHz versus frequency f Typical behavior at 20 °C KAL0577-I 10 2 B43510/520 Ω Z 10 1 10 0 10 10 470 µF/450 V 680 µF/450 V 1800 µF/400 V _1 _2 10 1 10 2 10 3 10 4 10 5 Hz 10 6 f 187 10/02 Herausgegeben von EPCOS AG Unternehmenskommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND ++49 89 636 09, FAX (0 89) 636-2 26 89 ( EPCOS AG 2002. Vervielfältigung, Veröffentlichung, Verbreitung und Verwertung dieser Broschüre und ihres Inhalts ohne ausdrückliche Genehmigung der EPCOS AG nicht gestattet. Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen für Erzeugnisse und Leistungen der Elektroindustrie, soweit nichts anderes vereinbart wird. Diese Broschüre ersetzt die vorige Ausgabe. Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgelegenen Vertrieb der EPCOS AG oder an unsere Vertriebsgesellschaften im Ausland. Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe enthalten. Auskünfte darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsgesellschaft einzuholen. Published by EPCOS AG Corporate Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY ++49 89 636 09, FAX (0 89) 636-2 26 89 ( EPCOS AG 2002. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices.