AZ Displays AQM1696A Specifications for liquid crystal display Datasheet

AZ DISPLAYS
SPECIFICATIONS FOR
LIQUID CRYSTAL DISPLAY
CUSTOMER APPROVAL
※ PART NO. : AQM1696A-FLW-FBH (AZ DISPLAYS) VER1.0
COMPANY
CHOP
APPROVAL
CUSTOMER
COMMENTS
AZ DISPLAYS ENGINEERING APPROVAL
DESIGNED BY
CHECKED BY
APPROVED BY
BOBBY
JAY
GUZHENGHUA
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
REVISION RECORD
REVISION
VER1.0
REVISION DATE
16/12-2010
AZ DISPLAYS
PAGE
CONTENTS
FIRST ISSUE
1
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
※ CONTENTS
1.0
GENERAL SPECIFICATION
2.0
ABSOLUTE MAXIMUM RATINGS
3.0
ELECTRICAL CHARACTERISTICS
4.0
OPTICAL CHARACTERISTICS
5.0
BLOCK DIAGRAM
6.0
PIN ASSIGNMENT
7.0
POWER SUPPLY
8.0
TIMING CHARACTERISTICS
9.0
MECHANICAL DIAGRAM
10.0 RELIABILITY TEST
11.0 INSTRUCTION DESCRIPTION
12.0 PRECAUTION FOR USING LCM
AZ DISPLAYS
2
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
1.0 GENERAL SPECS
1. Display Format
160*96 Dot matrix
2. Power Supply
3.0V
3. Module outline dimension
98.48mm(W) x 67.79mm(H) x 9.2mm(D)
4. Viewing Aera(W*H)
74.31mm(W) x 44.87mm(H)
5. Dot Size (W*H)
0.40mm(W) x 0.38mm(H)
6. Dot Pitch (W*H)
0.43mm(W) x 0.41mm(H)
7. Viewing Direction
6:00 O’Clock
8. Driving Method
1/96 Duty,1/11Bias
9. Control IC
ST7528 or compatible
10. Display Mode
FSTN/Positive/Transflective
11. Backlight Options
White LED /Side
12. Operating temperature
-20ºC ~ 70ºC
13. Storage temperature
-30ºC ~ 80ºC
14. ROHS
ROHS compliant
2.0 ABSOLUTE MAXIMUM RATINGS
Item
Symbol
Min
Typ
Max
Unit
Operating temperature
Top
-20
-
70
ºC
Storage temperature
Tst
-30
-
80
ºC
Input voltage
Vin
-0.5
-
Vdd+0.5
V
Supply voltage for logic
Vdd- Vss
-0.5
-
3.6
V
Supply voltage for LCD driving
Vout-Vss
-0.5
20
V
3.0 ELECTRICAL CHARACTERISTICS
3.1 Electrical Characteristics Of LCM
Item
Symbol
Condition
Min
Typ
Max
Unit
Power Supply Voltage
VDD
Ta=25ºC
2.8
3.0
3.2
V
Power Supply Current
Idd
Vdd=3.0V
--
1.4
2.0
mA
Input voltage (high)
Vih
H level
0.7*VDD
--
VDD
V
Input voltage (low)
Vil
L level
VSS
--
0.3*VDD
V
-20ºC
12.8
13.0
13.2
25ºC
12.3
12.5
12.7
70ºC
11.8
12.0
12.2
Recommended
Voltage
AZ DISPLAYS
LC
Driving
V0-Vss
V
3
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
3.2 The Characteristics Of Backlight
3.2.1 Electrical-Optical Characteristics Of LED Backlight (Ta=25ºC)
Item
Symbol
Condition
Min
Typ
Max
Unit
Forward Voltage
Vf
If=90mA
2.9
3.1
3.3
V
Reverse
Vr
-
--
--
5
V
Lv
If=90mA
200
240
--
cd/㎡
Uniformity
Δ
(Lvmin/Lvmax)%
70%
--
--
-
Peak wave length
λp
-
--
--
--
nm
x
If=90mA
0.29
--
0.34
um
y
If=90mA
0.29
--
0.34
um
-
If=90mA
-
20000
-
Hours
(1)
Voltage
Luminance(2)
(3)
Chroma coordinate
(4)
Lifetime
NOTE:
(1) Forward voltage means voltage applied directly to the LED
(2)The luminance is the average value of 5 points,The measurement instrument is BM-7 luminance
colorimeter.The diameter of aperture is Φ5mm
(3) Luminance means the backlight brightness without LCD.
(4) Backlight lifetime means luminance value larger than half of the original after 20000 hours’ continuous working.
3.2.2 Backlight Control Circuit FOR LCM(1x6=6 pcs LED)
A:Vin=5.0V
If=90mA(TYPE.)
Vf
K:0V
3.2.3 LED Characteristics Curves(for single led)
2.Forward
1.Forward current VS.Ambient Temperature
Forward Current (mA)
)
A
m
(
t
n
e
r
r
u
C
d
r
a
w
r
o
F
20
15
10
5
0
-30
current VS Forward Voltage
30
25
25
20
15
10
5
0
0
25
50 80
Ambient Temperature
AZ DISPLAYS
100
2
3
4
Forward Voltage
5
4
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
4.0 OPTICAL CHARACTERISTICS
Item
Symbol
Condition
Min
Typ
Max
Unit
Viewing angle (Left - right)
θ2
Cr ≥ 2.0
-35
-
35
deg
Viewing angle (Up-down)
θ1
Cr ≥ 2.0
-25
-
40
deg
Contrast Ratio
Cr
θ1=0°, θ2=0°
-
6
-
Response time (rise)
Tr
θ1=0°, θ2=0°
-
180
300
ms
Response time (fall)
Tf
θ1=0°, θ2=0°
-
150
250
ms
(1). Definition of Optical Response Time
(2). Definition of Contrast Ratio
AZ DISPLAYS
5
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
(3). Definition of Viewing Angle θ2 and θ1
5.0 BLOCK DIAGRAM
A(5.0V)
LED BACKLIGHT
K
COM49
COM95
COM50
LCD160X96
SEG159
COM0
SEG0
SEG160
ST7528P
COM46
VSS
VSS
VOUT
VSS
VDD
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
E
RW
A0
RST
AZ DISPLAYS
CSB
1
COM50
30
6
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
6.0 PIN ASSIGNMENT
Pin No.
Symbol
Function
1
CSB
Chip select signal
2
RST
Reset signal
3
A0
Display/Control data select signal
4
RW
Write- Read signal
5
E
6
DB0
Data bit0
7
DB1
Data bit1
8
DB2
Data bit2
Enable signal
9
DB3
Data bit3
10
DB4
Data bit4
11
DB5
Data bit5
12
DB6
Data bit6
13
DB7
Data bit7
14
VDD
Logic power supply
15
VSS
Ground
16
VOUT
17
VSS
LCD power supply
Ground
18
VSS
Ground
7.0 POWER SUPPLY
Vdd
LCD
MODULE Vout
VLCD
Vdd
Vss
AZ DISPLAYS
7
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
8.0 TIMING CHARACTERISTICS
AZ DISPLAYS
8
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
For more details,please refer to IC specification.
AZ DISPLAYS
9
AZ DISPLAYS
A
B
C
D
E
COM95
ALIGNMENT PADS
ON BOTH SIDES*2
SEG159
A
K
CAPACITOR*4
0.1uF/25V/0805
3
0.79mm THICKNESS
CAN COMPRESSED
TO 0.25mm.
1
2
3
4
5
5
THE Borde With 0.35mm
Thickness 2mm Around
SILICONE(COVER IC)
NO EXCEED LCD
BACK POLARIZER
1.59mm THICKNESS
CAN COMPRESSED
TO 0.5mm.
DETAIL B(5:1)
COVER WITH SILICONE
4
Note:Unspecified Tolerance:±0.2mm
COM0
160*96 DOTS
2
SEG0
F
1
6
6
DETAIL C(NOT SCALED)
7
7
8
8
A
B
C
D
E
F
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
9.0 MECHANICAL DIAGRAM
10
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
10.0 RELIABILITY TEST
Test Item
NO
1
High temperature
storage
2
Low temperature
storage
3
High temperature
Operation
4
Environmental
Test
5
Low temperature
Operation
High
temperature/High
Humidity Storage
Temperature
Cycle
6
Description
Applying the high storage
temperature Under normal humidity for
a long time Check normal performance
Applying the low storage temperature
Under normal humidity for a long time
Check normal performance
Apply the electric stress(Voltage and
current) Under high temperature for a
long time
Apply the electric stress Under low
temperature for a long time
Apply high temperature and high
humidity storage for a long time
Apply the low and high temperature
cycle
-30ºC<>25ºC<>80ºC <>25ºC
30min
10min 30min 10min
Test Condition
Remark
80 ºC
96hrs
-30ºC
96hrs
70 ºC
96hrs
-20ºC
96hrs
90% RH
40ºC
96hrs
Note1
Note1
Note2
Note2
-30ºC/80ºC
10 cycle
1 cycle
Check normal performance
7
Mechanical
Test
Vibration
test(Package
state)
Shock
test(package
state)
8
9
Applying vibration to product check
normal performance
Applying shock to product check
normal performance
Freq:10~55~10H
z
Amplitude:0.75m
m
1cycle time:1min
X.Y.Z every
direction for 15
cycles
Drop them
through 70cm
height to strike
horizontal plane
Other
Remark
Note1:Normal operations condition (25ºC±5ºC).
Note2:Pay attention to keep dewdrops from the module during this test.
AZ DISPLAYS
11
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
11.0 DISPLAY CONTROL INSTRUCTION
AZ DISPLAYS
12
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
AZ DISPLAYS
13
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
For more details,please refer to IC specification.
AZ DISPLAYS
14
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
12.0 PRECAUTION FOR USING LCM
1. When design the product with this LCD Module, make sure the viewing angle matches to its purpose of usage.
2. As LCD panel is made of glass substrate, Dropping the LCD module or banging it against hard objects may
cause cracking or fragmentation. Especially at corners and edges.
3. Although the polarizer of this LCD Module has the anti-glare coating, always be careful not to scratch its
surface. Use of a plastic cover is recommended to protect the surface of polarizer.
4. If the LCD module is stored at below specified temperature, the LC material may freeze and be deteriorated. If
it is stored at above specified temperature, the molecular orientation of the LC material may change to Liquid
state and it may not revert to its original state. Excessive temperature and humidity could cause polarizer peel
off or bubble. Therefore, the LCD module should always be stored within specified temperature range.
5. Saliva or water droplets must be wiped off immediately as those may leave stains or cause color changes if
remained for a long time. Water vapor will cause corrosion of ITO electrodes.
6. If the surface of LCD panel needs to be cleaned, wipe it swiftly with cotton or other soft cloth. If it is not still
clean enough, blow a breath on the surface and wipe again.
7. The module should be driven according to the specified ratings to avoid malfunction and permanent damage.
Applying DC voltage cause a rapid deterioration of LC material. Make sure to apply alternating waveform by
continuous application of the M signal. Especially the power ON/OFF sequence should be kept to avoid latchup
of driver LSIs and DC charge up to LCD panel.
8. Mechanical Considerations
a) LCM are assembled and adjusted with a high degree of precision. Avoid excessive shocks and do not
make any alterations or modifications. The following should be noted.
b) Do not tamper in any way with the tabs on the metal frame.
c) Do not modify the PCB by drilling extra holes, changing its outline, moving its components or modifying its
pattern.
d) Do not touch the elastomer connector; especially insert a backlight panel (for example, EL).
e) When mounting a LCM makes sure that the PCB is not under any stress such as bending or twisting.
Elastomer contacts are very delicate and missing pixels could result from slight dislocation of any of the
elements.
f) Avoid pressing on the metal bezel, otherwise the elastomer connector could be deformed and lose
contact, resulting in missing pixels.
9. Static Electricity
a) Operator
Ware the electrostatics shielded clothes because human body may be statically charged if not ware shielded clothes.
Never touch any of the conductive parts such as the LSI pads; the copper leads on the PCB and the interface terminals
with any parts of the human body.
b) Equipment
There is a possibility that the static electricity is charged to the equipment, which has a function of peeling or friction
action (ex: conveyer, soldering iron, working table). Earth the equipment through proper resistance (electrostatic
earth: 1x108 ohm).
AZ DISPLAYS
15
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
Only properly grounded soldering irons should be used.
If an electric screwdriver is used, it should be well grounded and shielded from commutator sparks.
The normal static prevention measures should be observed for work clothes and working benches; for the latter
conductive (rubber) mat is recommended.
c) Floor
Floor is the important part to drain static electricity, which is generated by operators or equipment.
There is a possibility that charged static electricity is not properly drained in case of insulating floor. Set the
electrostatic earth (electrostatic earth: 1x108 ohm).
d) Humidity
Proper humidity helps in reducing the chance of generating electrostatic charges. Humidity should be kept over
50%RH.
e) Transportation/storage
The storage materials also need to be anti-static treated because there is a possibility that the human body or storage
materials such as containers may be statically charged by friction or peeling.
The modules should be kept in antistatic bags or other containers resistant to static for storage.
f) Soldering
Solder only to the I/O terminals.Use only soldering irons with proper grounding and no leakage.
Soldering temperature : 280°C ± 10°C
Soldering time: 3 to 4 sec.
Use eutectic solder with resin flux fill.
If flux is used, the LCD surface should be covered to avoid flux spatters. Flux residue should be removed
afterwards.
g) Others
The laminator (protective film) is attached on the surface of LCD panel to prevent it from scratches or stains. It should
be peeled off slowly using static eliminator.
Static eliminator should also be installed to the workbench to prevent LCD module from static charge.
10. Operation
a) Driving voltage should be kept within specified range; excess voltage shortens display life.
b) Response time increases with decrease in temperature.
c) Display may turn black or dark blue at temperatures above its operational range; this is (however not
pressing on the viewing area) may cause the segments to appear “fractured”.
d) Mechanical disturbance during operation (such as pressing on the viewing area) may cause the
segments to appear “fractured”.
11. If any fluid leaks out of a damaged glass cell, wash off any human part that comes into contact with soap and
water. The toxicity is extremely low but caution should be exercised at all the time.
12. Disassembling the LCD module can cause permanent damage and it should be strictly avoided.
13. LCD retains the display pattern when it is applied for long time (Image retention). To prevent image retention,
do not apply the fixed pattern for a long time. Image retention is not a deterioration of LCD. It will be removed
after display pattern is changed.
14. Do not use any materials, which emit gas from epoxy resin (hardener for amine) and silicone adhesive agent
AZ DISPLAYS
16
AQM1696A-FLW-FBH(AZ DISPLAYS) GRAPHIC MODULE VER1.0
(dealcohol or deoxym) to prevent discoloration of polarizer due to gas.
15. Avoid the exposure of the module to the direct sunlight or strong ultraviolet light for a long time.
16. The brightness of LCD module may be affected by the routing of CCFL cables due to leakage to the chassis
through coupling effect. The inverter circuit needs to be designed taking the level of leakage current into
consideration. Thorough evaluation is needed for LCD module and inverter built into its host equipment to
ensure specified brightness.
AZ DISPLAYS
17
Similar pages