Low Cost, 300 MHz Rail-to-Rail Amplifiers AD8061/AD8062/AD8063 FEATURES APPLICATIONS Low cost Single (AD8061), dual (AD8062) Single with disable (AD8063) Rail-to-rail output swing Low offset voltage: 6 mV High speed 300 MHz, −3 dB bandwidth (G = 1) 650 V/μs slew rate 8.5 nV/√Hz at 5 V 35 ns settling time to 0.1% with 1 V step Operates on 2.7 V to 8 V supplies Input voltage range = −0.2 V to +3.2 V with VS = 5 Excellent video specs (RL = 150 Ω, G = 2) Gain flatness 0.1 dB to 30 MHz 0.01% differential gain error 0.04° differential phase error 35 ns overload recovery Low power 6.8 mA/amplifier typical supply current AD8063 400 μA when disabled Imaging Photodiode preamps Professional video and cameras Hand sets DVDs/CDs Base stations Filters ADC drivers CONNECTION DIAGRAMS DISABLE (AD8063 ONLY) 7 +VS +IN 3 6 VOUT –VS 4 5 NC (Not to Scale) 01065-001 –IN 2 NC = NO CONNECT Figure 1. 8-Lead SOIC (R) AD8063 6 –VS 2 4 8 +VS –IN1 2 7 VOUT2 +IN1 3 6 –IN2 –VS 4 5 +IN2 (Not to Scale) AD8061 +VS VOUT 1 5 DISABLE +IN 3 1 Figure 2. 8-Lead SOIC (R)/MSOP (RM) –IN (Not to Scale) 5 +VS –VS 2 01065-002 VOUT 1 AD8062 VOUT1 01065-003 8 Figure 3. 6-Lead SOT-23 (RT) +IN 3 4 –IN (Not to Scale) 01065-004 AD8061/ AD8063 NC 1 Figure 4. 5-Lead SOT-23 (RT) GENERAL DESCRIPTION The AD8061, AD8062, and AD8063 offer a typical low power of 6.8 mA/amplifier, while being capable of delivering up to 50 mA of load current. The AD8063 has a power-down disable feature that reduces the supply current to 400 μA. These features make the AD8063 ideal for portable and battery-powered applications where size and power are critical. R F = 50Ω 0 VO = 0.2V p-p RL = 1kΩ VBIAS = 1V –3 RF = 0Ω RF –6 OUT RL IN 50Ω –9 ± VBIAS 01065-005 Despite being low cost, the AD8061, AD8062, and AD8063 provide excellent overall performance. For video applications their differential gain and phase errors are 0.01% and 0.04° into a 150 Ω load, along with 0.1 dB flatness out to 30 MHz. Additionally, they offer wide bandwidth to 300 MHz along with 650 V/μs slew rate. 3 NORMALIZED GAIN (dB) The AD8061, AD8062, and AD8063 are rail-to-rail output voltage feedback amplifiers offering ease of use and low cost. They have bandwidth and slew rate typically found in current feedback amplifiers. All have a wide input common-mode voltage range and output voltage swing, making them easy to use on single supplies as low as 2.7 V. –12 1 10 100 1k FREQUENCY (MHz) Figure 5. Small Signal Response, RF = 0 Ω, 50 Ω Rev. D Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 © 2005 Analog Devices, Inc. All rights reserved. AD8061/AD8062/AD8063 TABLE OF CONTENTS Features .............................................................................................. 1 Overload Behavior and Recovery ............................................ 15 Applications....................................................................................... 1 Capacitive Load Drive ............................................................... 15 Revision History ............................................................................... 2 Disable Operation ...................................................................... 16 Specifications..................................................................................... 3 Board Layout Considerations ................................................... 16 Absolute Maximum Ratings............................................................ 6 Applications..................................................................................... 17 Maximum Power Dissipation ..................................................... 6 Single-Supply Sync Stripper...................................................... 17 ESD Caution.................................................................................. 6 RGB Amplifier ............................................................................ 17 Typical Performance Characteristics ............................................. 7 Multiplexer .................................................................................. 18 Circuit Description......................................................................... 14 Outline Dimensions ....................................................................... 19 Headroom Considerations ........................................................ 14 Ordering Guide .......................................................................... 20 REVISION HISTORY 12/05—Rev. C to Rev. D Updated Format..................................................................Universal Change to Features and General Description............................... 1 Updated Outline Dimensions ....................................................... 19 Changes to Ordering Guide .......................................................... 20 5/01—Rev. B to Rev. C Replaced TPC 9 with new graph .................................................... 7 11/00—Rev. A to Rev. B 2/00—Rev. 0 to Rev. A 11/99—Revision 0: Initial Version Rev. D | Page 2 of 20 AD8061/AD8062/AD8063 SPECIFICATIONS TA = 25°C, VS = 5 V, RL = 1 kΩ, VO = 1 V, unless otherwise noted. Table 1. Parameter DYNAMIC PERFORMANCE −3 dB Small Signal Bandwidth −3 dB Large Signal Bandwidth Bandwidth for 0.1 dB Flatness Slew Rate Settling Time to 0.1% NOISE/DISTORTION PERFORMANCE Total Harmonic Distortion Crosstalk, Output to Output Input Voltage Noise Input Current Noise Differential Gain Error (NTSC) Differential Phase Error (NTSC) Third Order Intercept SFDR DC PERFORMANCE Input Offset Voltage Conditions Min Typ G = 1, VO = 0.2 V p-p G = –1, +2, VO = 0.2 V p-p G = 1, VO = 1 V p-p G = 1, VO = 0.2 V p-p G = 1, VO = 2 V step, RL = 2 kΩ G = 2, VO = 2 V step, RL = 2 kΩ G = 2, VO = 2 V step 150 60 320 115 280 30 650 500 35 MHz MHz MHz MHz V/μs V/μs ns −77 −50 −90 8.5 1.2 0.01 0.04 28 62 dBc dBc dBc nV/√Hz pA/√Hz % Degrees dBc dB 500 300 fC = 5 MHz, VO = 2 V p-p, RL = 1 kΩ fC = 20 MHz, VO = 2 V p-p, RL = 1 kΩ f = 5 MHz, G = 2, AD8062 f = 100 kHz f = 100 kHz G = 2, RL = 150 Ω G = 2, RL = 150 Ω f = 10 MHz f = 5 MHz 68 74 1 2 3.5 3.5 4 0.3 70 90 VCM = –0.2 V to +3.2 V 62 13 1 −0.2 to +3.2 80 RL = 150 Ω RL = 2 kΩ VO = 0.5 V to 4.5 V 30% overshoot: G = 1, RS = 0 Ω G = 2, RS = 4.7 Ω 0.3 0.25 25 TMIN to TMAX Input Offset Voltage Drift Input Bias Current TMIN to TMAX Input Offset Current Open-Loop Gain INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output Voltage Swing—Load Resistance Is Terminated at Midsupply Output Current Capacitive Load Drive, VOUT = 0.8 V VO = 0.5 V to 4.5 V, RL = 150 Ω VO = 0.5 V to 4.5 V, RL = 2 kΩ POWER-DOWN DISABLE Turn-On Time Turn-Off Time DISABLE Voltage—Off DISABLE Voltage—On POWER SUPPLY Operating Range Quiescent Current per Amplifier Supply Current when Disabled (AD8063 Only) Power Supply Rejection Ratio 0.1 to 4.5 0.1 to 4.9 50 25 300 Max 6 6 9 9 4.5 ∆VS = 2.7 V to 5 V Rev. D | Page 3 of 20 72 5 6.8 0.4 80 mV mV μV/°C μA μA ±μA dB dB MΩ pF V dB 4.75 4.85 40 300 2.8 3.2 2.7 Unit V V mA pF pF ns ns V V 8 9.5 V mA mA dB AD8061/AD8062/AD8063 TA = 25°C, VS = 3 V, RL = 1 kΩ, VO = 1 V, unless otherwise noted. Table 2. Parameter DYNAMIC PERFORMANCE –3 dB Small Signal Bandwidth –3 dB Large Signal Bandwidth Bandwidth for 0.1 dB Flatness Slew Rate Settling Time to 0.1% NOISE/DISTORTION PERFORMANCE Total Harmonic Distortion Crosstalk, Output to Output Input Voltage Noise Input Current Noise DC PERFORMANCE Input Offset Voltage Conditions Min Typ G = 1, VO = 0.2 V p-p G = –1, +2, VO = 0.2 V p-p G = 1, VO = 1 V p-p G = 1, VO = 0.2 V p-p G = 1, VO = 1 V step, RL = 2 kΩ G = 2, VO = 1.5 V step, RL = 2 kΩ G = 2, VO = 1 V step 150 60 300 115 250 30 280 230 40 MHz MHz MHz MHz V/μs V/μs ns −60 −44 −90 8.5 1.2 dBc dBc dBc nV/√Hz pA/√Hz 190 180 fC = 5 MHz, VO = 2 V p-p, RL = 1 kΩ fC = 20 MHz, VO = 2 V p-p, RL = 1 kΩ f = 5 MHz, G = 2 f = 100 kHz f = 100 kHz TMIN to TMAX Input Offset Voltage Drift Input Bias Current TMIN to TMAX Input Offset Current Open-Loop Gain INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Capacitive Load Drive, VOUT = 0.8 V VO = 0.5 V to 2.5 V, RL = 150 Ω VO = 0.5 V to 2.5 V, RL = 2 kΩ 66 74 6 6 8.5 8.5 4.5 13 1 −0.2 to +12 80 VCM = –0.2 V to +1.2 V RL = 150 Ω RL = 2 kΩ VO = 0.5 V to 2.5 V 30% overshoot, G = 1, RS = 0 Ω G = 2, RS = 4.7 Ω 1 2 3.5 3.5 4 0.3 70 90 Max 0.3 0.3 POWER-DOWN DISABLE Turn-On Time Turn-Off Time DISABLE Voltage—Off DISABLE Voltage—On 0.1 to 2.87 0.1 to 2.9 25 25 300 2.7 72 Rev. D | Page 4 of 20 6.8 0.4 80 mV mV μV/°C μA μA ±μA dB dB MΩ pF V dB 2.85 2.90 40 300 0.8 1.2 POWER SUPPLY Operating Range Quiescent Current per Amplifier Supply Current when Disabled (AD8063 Only) Power Supply Rejection Ratio Unit V V mA pF pF ns ns V V 3 9 V mA mA dB AD8061/AD8062/AD8063 TA = 25°C, VS = 2.7 V, RL = 1 kΩ, VO = 1 V, unless otherwise noted. Table 3. Parameter DYNAMIC PERFORMANCE –3 dB Small Signal Bandwidth Bandwidth for 0.1 dB Flatness Slew Rate Settling Time to 0.1% NOISE/DISTORTION PERFORMANCE Total Harmonic Distortion Crosstalk, Output to Output Input Voltage Noise Input Current Noise DC PERFORMANCE Input Offset Voltage Conditions Min Typ G = 1, VO = 0.2 V p-p G = –1, +2, VO = 0.2 V p-p G = 1, VO = 1 V p-p G = 1, VO = 0.2 V p-p, VO dc = 1 V G = 1, VO = 0.7 V step, RL = 2 kΩ G = 2, VO = 1.5 V step, RL = 2 kΩ G = 2, VO = 1 V step 150 60 300 115 230 30 150 130 40 MHz MHz MHz MHz V/μs V/μs ns –60 –44 –90 8.5 1.2 dBc dBc dBc nV/√Hz pA/√Hz 110 95 fC = 5 MHz, VO = 2 V p-p, RL = 1 kΩ fC = 20 MHz, VO = 2 V p-p, RL = 1 kΩ f = 5 MHz, G = 2 f = 100 kHz f = 100 kHz TMIN to TMAX Input Offset Voltage Drift Input Bias Current TMIN to TMAX Input Offset Current Open-Loop Gain INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Capacitive Load Drive, VOUT = 0.8 V VO = 0.5 V to 2.2 V, RL = 150 Ω VO = 0.5 V to 2.2 V, RL = 2 kΩ 63 74 POWER-DOWN DISABLE Turn-On Time Turn-Off Time DISABLE Voltage—Off DISABLE Voltage—On POWER SUPPLY Operating Range Quiescent Current per Amplifier Supply Current when Disabled (AD8063 Only) Power Supply Rejection Ratio 6 6 8.5 4.5 13 1 –0.2 to +0.9 0.8 VCM = –0.2 V to +0.9 V RL = 150 Ω RL = 2 kΩ VO = 0.5 V to 2.2 V 30% overshoot: G = 1, RS = 0 Ω G = 2, RS = 4.7 Ω 1 2 3.5 3.5 4 0.3 70 90 Max 0.3 0.25 0.1 to 2.55 0.1 to 2.6 25 25 2.55 2.6 40 300 0.5 0.9 6.8 0.4 80 Rev. D | Page 5 of 20 mV mV μV/°C μA μA ±μA dB dB MΩ pF V dB 300 2.7 Unit V V mA pF pF ns ns V V 8 8.5 V mA mA dB AD8061/AD8062/AD8063 ABSOLUTE MAXIMUM RATINGS Table 4. Parameter Supply Voltage Internal Power Dissipation 1 8-lead SOIC (R) 5-lead SOT-23 (RT) 6-lead SOT-23 (RT) 8-lead MSOP (RM) Input Voltage (Common-Mode) (−VS − 0.2 V) to (+VS − 1.8 V) Differential Input Voltage Output Short-Circuit Duration Storage Temperature Range R-8, RM-8, SOT-23-5, SOT-23-6 Operating Temperature Range Lead Temperature Range (Soldering 10 sec) 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rating 8V 0.8 W 0.5 W 0.5 W 0.6 W MAXIMUM POWER DISSIPATION ±VS Observe Power Derating Curves −65°C to +125°C −40°C to +85°C 300°C Specification is for device in free air. 8-Lead SOIC: θJA = 160°C/W; θJC = 56°C/W. 5-Lead SOT-23: θJA = 240°C/W; θJC = 92°C/W. 6-Lead SOT-23: θJA = 230°C/W; θJC = 92°C/W. 8-Lead MSOP: θJA = 200°C/W; θJC = 44°C/W. The maximum power that can be safely dissipated by the AD806x is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately 150°C. Temporarily exceeding this limit may cause a shift in parametric performance due to a change in the stresses exerted on the die by the package. Exceeding a junction temperature of 175°C for an extended period can result in device failure. While the AD806x is internally short-circuit protected, this may not be sufficient to guarantee that the maximum junction temperature (150°C) is not exceeded under all conditions. To ensure proper operation, it is necessary to observe the maximum power derating curves. TJ = 150°C 8-LEAD SOIC PACKAGE 1.5 1.0 0.5 MSOP SOT-23-5, -6 0 –50 –40 –30 –20 –10 0 10 20 01065-006 MAXIMUM POWER DISSIPATION (W) 2.0 30 40 50 60 70 80 AMBIENT TEMPERATURE (°C) Figure 6. Maximum Power Dissipation vs. Temperature for AD8061/AD8062/AD8063 ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. D | Page 6 of 20 90 AD8061/AD8062/AD8063 TYPICAL PERFORMANCE CHARACTERISTICS 3 G=1 +VOUT @ +85°C NORMALIZED GAIN (dB) 0 +VOUT @ +25°C 0.8 +VOUT @ –40°C 0.6 –VOUT @ –40°C 0.4 –VOUT @ +25°C 0 20 10 0 30 40 50 60 70 80 G=2 –6 G=5 VO = 0.2V p-p RL = 1kΩ VBIAS = 1V –9 –VOUT @ +85°C 0.2 –3 01065-010 1.0 01065-007 VOLTAGE DIFFERENTIAL FROM VS 1.2 –12 1 90 10 3 18 VO = 1.0V p-p RL = 1kΩ VBIAS = 1V AD8062 G=1 0 NORMALIZED GAIN (dB) 14 12 10 AD8061 8 6 4 G=2 –3 G=5 –6 2 0 2 3 5 4 6 7 01065-011 –9 01065-008 POWER SUPPLY CURRENT (mA) 1k Figure 10. Small Signal Frequency Response Figure 7. Output Saturation Voltage vs. Load Current 16 100 FREQUENCY (MHz) LOAD CURRENT (mA) –12 8 1 10 SINGLE POWER SUPPLY (V) 100 1k FREQUENCY (MHz) Figure 11. Large Signal Frequency Response Figure 8. ISUPPLY vs. VSUPPLY 3 RF = 50Ω 3 VS = 5V VO = 0.2V p-p RL = 1kΩ VBIAS = 1V VO = 0.2V p-p RL = 1kΩ VBIAS = 1V NORMALIZED GAIN (dB) RF –6 OUT IN RL 50Ω –9 VBIAS –12 1 10 100 G = –1 G = –5 –3 G = –2 RF –6 OUT IN RL 50Ω –9 VBIAS 1k 01065-012 –3 0 RF = 0Ω 01065-009 NORMALIZED GAIN (dB) 0 –12 1 FREQUENCY (MHz) 10 100 FREQUENCY (MHz) Figure 9. Small Signal Response, RF = 0 Ω, 50 Ω Figure 12. Small Signal Frequency Response Rev. D | Page 7 of 20 1k AD8061/AD8062/AD8063 3 0 HARMONIC DISTORTION (dBc) NORMALIZED GAIN (dB) 0 G = –1 –3 G = –2 –6 G = –5 01065-013 –9 –12 1 10 –20 –30 2ND @ 1MHz –40 3RD @ 10MHz –50 –60 –70 –80 –90 –100 0.5 1k 100 VS = 5V RL = 1kΩ G=1 –10 1.5 10μF + –50 0.1μF 1kΩ –0.1 VS = 5V VS = 3V –0.3 50Ω 1MΩ INPUT 52.3Ω 0.1μF 1.25Vdc –70 + 1kΩ (RLOAD) – –80 2ND H –90 –0.4 10 100 3RD H –110 0.01 1k Figure 14. 0.1 dB Flatness Figure 17. Harmonic Distortion for a 1 V p-p Output Signal vs. Input Signal DC Bias 80 SERIES 1 200 –30 150 –40 100 –50 0 20 –50 –100 0 –150 –300 0.1 1 10 100 01065-015 –250 2ND VS = 5V RL = 1kΩ G=5 VO = 1V p-p 3RD 10MHz –60 –70 –80 2ND –90 3RD 5MHz –100 –200 – 20 DISTORTION (dB) SERIES 2 PHASE (Degrees) 50 40 – 40 0.01 50 10 FREQUENCY (MHz, START = 10kHz, STOP = 30MHz) FREQUENCY (MHz) 60 1 0.1 1MHz –110 3RD 2ND –120 0 1k FREQUENCY (MHz) 1 2 3 4 OUTPUT SIGNAL DC BIAS (V) Figure 15. AD8062 Open-Loop Gain and Phase vs. Frequency, VS = 5 V, RL = 1 kΩ Figure 18. Harmonic Distortion vs. Output Signal DC Bias Rev. D | Page 8 of 20 01065-018 1 01065-017 –100 01065-014 –0.5 OPEN-LOOP GAIN (dB) 3.5 3.0 604Ω 5V DISTORTION (dB) NORMALIZED GAIN (dB) VO = 0.2V p-p RL = 1kΩ VBIAS = 1V G=1 –60 –0.2 2.5 Figure 16. Harmonic Distortion for a 1 V p-p Signal vs. Input Signal DC Bias –40 0 2.0 INPUT SIGNAL BIAS (V) Figure 13. Large Signal Frequency Response VS = 2.7V 3RD @ 1MHz 2ND @ 10MHz 1.0 FREQUENCY (MHz) 0.1 01065-016 VS = 5V VO = 1V p-p RL = 1kΩ VBIAS = 1V 5 AD8061/AD8062/AD8063 –40 0.1μF 50Ω 1kΩ –70 + 10μF 1kΩ 50Ω 1kΩ 1MΩ INPUT TO 3589A 2ND @ 2MHz –80 2ND @ 500kHz –90 3RD @ 2MHz 01065-019 –100 3RD @ 500kHz –110 1.0 1.5 2.0 2.5 4.0 3.5 3.0 4.5 0 –0.01 –0.02 –0.04 –0.06 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH 0.02 0 –0.02 –0.04 01065-022 5V 0.01 DIFFERENTIAL GAIN (%) DISTORTION (dB) –60 2ND @ 10MHz DIFFERENTIAL PHASE (Degrees) VS = 5V RF = RL = 1kΩ G=2 –50 –0.06 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH RTO OUTPUT (V p-p) Figure 22. Differential Gain and Phase Error, G = 2, NTSC Input Signal, RL = 1 kΩ, VS = 5 V Figure 19. Harmonic Distortion vs. Output Signal Amplitude –30 DIFFERENTIAL GAIN (%) VS = 5V RI = RL = 1kΩ VO = 2V p-p G=2 S1 3RD HARMONIC/ DUAL ±2.5V SUPPLY –60 S1 2ND HARMONIC/ DUAL ±2.5V SUPPLY –70 –100 S1 3RD HARMONIC/ SINGLE +5V SUPPLY 0.1 1 01065-020 –90 –110 0.01 –0.010 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH S1 2ND HARMONIC/ SINGLE +5V SUPPLY –80 0 –0.005 10 0.04 0.03 0.02 0.01 0 –0.01 –0.02 01065-023 DISTORTION (dB) –50 0.010 0.005 DIFFERENTIAL PHASE (Degrees) –40 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH FREQUENCY (MHz, START = 10kHz, STOP = 30MHz) Figure 20. Harmonic Distortion vs. Frequency 1.0 1000 VS = 5V RL = 1kΩ G=1 0.9 900 800 0.7 700 SLEW RATE (V/μs) 0.8 0.6 0.5 0.4 0.3 0.2 FALLING EDGE VS = 5V RL = 1kΩ G=1 RISING EDGE 600 500 400 300 0.1 0 0 0.1 0.2 0.3 0.4 01065-024 200 01065-021 OUTPUT VOLTAGE (V) Figure 23. Differential Gain and Phase Error, G = 2, NTSC Input Signal, RL = 150 Ω, VS = 5 V 100 0 1.0 0.5 1.5 2.0 2.5 OUTPUT STEP AMPLITUDE (V) TIME (μs) Figure 21. 400 mV Pulse Response Figure 24. Slew Rate vs. Output Step Amplitude Rev. D | Page 9 of 20 3.0 AD8061/AD8062/AD8063 1400 FALLING EDGE VS = ±4V 1200 2.5V FALLING EDGE VS = +5V VOUT VOLTS 1000 800 600 RISING EDGE VS = ±4V 400 0V RISING EDGE VS = +5V 01065-025 200 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 01065-028 SLEW RATE (V/μs) VS = ±2.5V G=1 RL = 1kΩ VIN 500mV/DIV 0 4.0 20 40 60 80 100 120 140 160 OUTPUT STEP (V) 200 Figure 28. Input Overload Recovery, Input Step = 0 V to 2 V Figure 25. Slew Rate vs. Output Step Amplitude, G = 2, RL = 1 kΩ, VS = 5 V 1k VS = ±2.5V G=5 RL = 1kΩ VS = 5V RL = 1kΩ VOUT 2.5V 100 VOLTS VOLTAGE NOISE (nV/ Hz) 180 TIME (ns) VIN 1.0V 10 1 10 100 1k 10k 100k 1M 01065-029 01065-026 0V 500mV/DIV 0 10M 20 40 60 100 120 140 160 180 200 TIME (ns) FREQUENCY (Hz) Figure 29. Output Overload Recovery, Input Step = 0 V to 1 V Figure 26. Voltage Noise vs. Frequency 0 100 –10 VS = 5V RL = 1kΩ –20 VCM = 0.2V p-p RL = 100Ω VS = ±2.5V SIDE 2 –30 10 1 –40 –50 –60 604Ω 604Ω –70 VIN 200mV p-p –80 0 10 100 1k 10k 100k 1M 10M 50Ω 154Ω 57.6Ω 154Ω –90 –100 0.01 0.1 1 10 FREQUENCY (MHz) FREQUENCY (Hz) Figure 27. Current Noise vs. Frequency Figure 30. CMRR vs. Frequency Rev. D | Page 10 of 20 01065-030 CMRR (dB) SIDE 1 01065-027 CURRENT NOISE (pA/ Hz) 80 100 500 AD8061/AD8062/AD8063 0 7 ΔVS = 0.2V p-p RL = 1kΩ VS = 5V –10 VS = 5V 6 –20 –PSRR 5 ISUPPLY (mA) PSRR (dB) –30 –40 –50 +PSRR –60 –70 4 3 2 –80 –100 0.01 0.1 10 1 100 0 1.0 500 01065-034 1 01065-031 –90 1.5 2.0 FREQUENCY (MHz) Figure 31. ±PSRR vs. Frequency Delta +2.5V VDISABLE 5 1kΩ –2.5V –70 INPUT = SIDE 2 INPUT = SIDE 1 –80 –90 VS = 5V VIN = 400mV rms RL = 1kΩ G=2 –100 –110 0.1 5.0 1 10 100 4 3 2 1 0 VOUT 01065-035 –60 OUTPUT VOLTAGE (V) OUT IN 50Ω 4.5 VS = 5V G=2 fIN = 10MHz @ 1.3VBIAS RL = 100Ω –40 –50 4.0 6 1kΩ 01065-032 OUTPUT TO OUTPUT CROSSTALK (dB) 3.5 –30 –120 0.01 –1 500 0 0.8 0.4 1.2 1.6 2.0 TIME (μs) FREQUENCY (MHz) Figure 32. AD8062 Crosstalk, VOUT = 2.0 V p-p, RL = 1 kΩ, G = 2, VS = 5 V Figure 35. DISABLE Function, Voltage = 0 V to 5 V 1k 0 VS = 5V VO = 0.2V p-p RL = 1kΩ VBIAS = 1V –10 –20 100 IMPEDANCE (Ω) –30 –40 –50 –60 –70 VS = 5V VO = 0.2V p-p RL = 1kΩ VBIAS = 1V 10 1 –80 –90 1 10 100 0.01 0.1 1k 01065-036 0.1 01065-033 DISABLED ISOLATION (dB) 3.0 Figure 34. DISABLE Voltage vs. Supply Current –20 1kΩ 2.5 DISABLE VOLTAGE 1 10 100 FREQUENCY (MHz) FREQUENCY (MHz) Figure 36. Output Impedance vs. Frequency, VOUT = 0.2 V p-p, RL = 1 kΩ, VS = 5 V Figure 33. Disabled Output Isolation Frequency Response Rev. D | Page 11 of 20 1k AD8061/AD8062/AD8063 VS = 5V G=2 RL = 1kΩ VIN = 1V p-p +0.1% 3.5V –0.1% 2.5V 1kΩ 1kΩ 1.5V RL = 1kΩ 01065-037 50Ω t=0 01065-040 SETTLING TIME TO 0.1% VS = 5V RL = 1kΩ 500mV/DIV 0 20ns/DIV 10 20 30 40 50 60 70 80 90 100 TIME (ns) Figure 37. Output Settling Time to 0.1% Figure 40. 1 V Step Response 50 45 2.6V 40 35 RISING EDGE 30 2.5V 25 20 5 0 0.5 1.0 1.5 2.0 01065-038 VS = 5V RL = 1kΩ G=1 10 01065-041 2.4V 15 20mV/DIV 0 2.5 10 20 OUTPUT VOLTAGE STEP 30 40 50 60 TIME (ns) 70 80 90 100 Figure 41. 100 mV Step Response Figure 38. Settling Time vs. VOUT VS = 5V G = –1 RF = 1kΩ RL = 1kΩ VS = 5V G=2 RF = RL = 1kΩ VIN = 4V p-p 4.86 2.43 0V 1V 2μs 2μs/DIV Figure 39. Output Swing Figure 42. Output Rail-to-Rail Swing Rev. D | Page 12 of 20 1V/DIV 01065-042 0V 01065-039 SETTLING TIME (ns) VS = 5V G=2 RL = 1kΩ VIN = 100mV FALLING EDGE AD8061/AD8062/AD8063 VS = 5V G=2 RL = RF = 1kΩ VIN = 2V p-p 4.5V 2.5V 2.5V 2.4V 0.5V 01065-043 2.6V 50mV/DIV 0 5 10 15 20 25 30 35 40 45 01065-044 VS = 5V G=1 RL = 1kΩ 1V/DIV 50 0 5 10 15 20 25 30 35 TIME (ns) TIME (ns) Figure 44. 2 V Step Response Figure 43. 200 mV Step Response Rev. D | Page 13 of 20 40 45 50 AD8061/AD8062/AD8063 CIRCUIT DESCRIPTION –0.4 –0.8 –1.2 –1.6 –2.0 –2.4 HEADROOM CONSIDERATIONS –2.8 These amplifiers are designed for use in low voltage systems. To obtain optimum performance, it is useful to understand the behavior of the amplifier as input and output signals approach the amplifier’s headroom limits. –3.2 01065-045 VOS (mV) The AD8061/AD8062/AD8063 family is comprised of high speed voltage feedback op amps. The high slew rate input stage is a true, single-supply topology, capable of sensing signals at or below the minus supply rail. The rail-to-rail output stage can pull within 30 mV of either supply rail when driving light loads and within 0.3 V when driving 150 Ω. High speed performance is maintained at supply voltages as low as 2.7 V. –3.6 –4.0 –0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 VCM (V) Figure 45. VOS vs. Common-Mode Voltage, VS = 5 V 2 0 VCM = 3.0 VCM = 3.1 GAIN (dB) Exceeding the headroom limit is not a concern for any inverting gain on any supply voltage, as long as the reference voltage at the amplifier’s positive input lies within the amplifier’s input common-mode range. The input stage is the headroom limit for signals when the amplifier is used in a gain of 1 for signals approaching the positive rail. Figure 45 shows a typical offset voltage vs. input common-mode voltage for the AD806x amplifier on a 5 V supply. Accurate dc performance is maintained from approximately 200 mV below the minus supply to within 1.8 V of the positive supply. For high-speed signals, however, there are other considerations. Figure 46 shows −3 dB bandwidth vs. dc input voltage for a unity-gain follower. As the common-mode voltage approaches the positive supply, the amplifier holds together well, but the bandwidth begins to drop at 1.9 V within +VS. This manifests itself in increased distortion or settling time. Figure 16 plots the distortion of a 1 V p-p signal with the AD806x amplifier used as a follower on a 5 V supply vs. signal common-mode voltage. Distortion performance is maintained until the input signal center voltage gets beyond 2.5 V, as the peak of the input sine wave begins to run into the upper common-mode voltage limit. VCM = 3.2 –2 VCM = 3.3 VCM = 3.4 –4 –6 –8 0.1 01065-046 The AD806x’s input common-mode voltage range extends from the negative supply voltage (actually 200 mV below this), or ground for single-supply operation, to within 1.8 V of the positive supply voltage. Thus, at a gain of 2, the AD806x can provide full rail-to-rail output swing for supply voltage as low as 3.6 V, assuming the input signal swing from −VS (or ground) to +VS/2. At a gain of 3, the AD806x can provide a rail-to-rail output range down to 2.7 V total supply voltage. 1 10 100 1k 10k FREQUENCY (MHz) Figure 46. Unity-Gain Follower Bandwidth vs. Input Common Mode, VS = 5 V Higher frequency signals require more headroom than lower frequencies to maintain distortion performance. Figure 47 illustrates how the rising edge settling time for the amplifier configured as a unity-gain follower stretches out as the top of a 1 V step input approaches and exceeds the specified input common-mode voltage limit. For signals approaching the minus supply and inverting gain and high positive gain configurations, the headroom limit is the output stage. The AD806x amplifiers use a common emitter style output stage. This output stage maximizes the available output range, limited by the saturation voltage of the output transistors. The saturation voltage increases with the drive current the output transistor is required to supply, due to the output transistors’ collector resistance. The saturation voltage is estimated using the equation VSAT = 25 mV + IO × 8 Ω, where IO is the output current, and 8 Ω is a typical value for the output transistors’ collector resistance. Rev. D | Page 14 of 20 AD8061/AD8062/AD8063 3.6 3.7 3.4 3.5 OUTPUT VOLTAGE (V) 3.0 2V TO 3V STEP 2.1V TO 3.1V STEP 2.2V TO 3.2V STEP 2.6 2.3V TO 3.3V STEP 2.4 4 8 12 16 20 24 28 2.9 VOLTAGE STEP FROM 2.4V TO 3.6V 2.7 VOLTAGE STEP FROM 2.4V TO 3.8V, 4V AND 5V 2.3 01065-047 0 VOLTAGE STEP FROM 2.4V TO 3.4V 2.5 2.4V TO 3.4V STEP 2.2 2.0 3.1 01065-048 2.8 3.3 2.1 0 32 100 200 300 400 500 600 TIME (ns) TIME (ns) Figure 48. Pulse Response for G = 1 Follower, Input Step Overloading the Input Stage Figure 47. Output Rising Edge for 1 V Step at Input Headroom Limits, G = 1, VS = 5 V, 0 V As the saturation point of the output stage is approached, the output signal shows increasing amounts of compression and clipping. As in the input headroom case, the higher frequency signals require a bit more headroom than lower frequency signals. Figure 16, Figure 17, and Figure 18 illustrate this point, plotting typical distortion vs. output amplitude and bias for gains of 2 and 5. Output Output overload recovery is typically within 40 ns after the amplifier’s input is brought to a nonoverloading value. Figure 49 shows output recovery transients for the amplifier recovering from a saturated output from the top and bottom supplies to a point at midsupply. 5.0 4.6 INPUT AND OUTPUT VOLTAGE (V) OVERLOAD BEHAVIOR AND RECOVERY Input The specified input common-mode voltage of the AD806x is −200 mV below the negative supply to within 1.8 V of the positive supply. Exceeding the top limit results in lower bandwidth and increased settling time as seen in Figure 46 and Figure 47. Pushing the input voltage of a unity-gain follower beyond 1.6 V within the positive supply leads to the behavior shown in Figure 48—an increasing amount of output error and much increased settling time. Recovery time from input voltages 1.6 V or closer to the positive supply is approximately 35 ns, which is limited by the settling artifacts caused by transistors in the input stage coming out of saturation. The AD806x family does not exhibit phase reversal, even for input voltages beyond the voltage supply rails. Going more than 0.6 V beyond the power supplies will turn on protection diodes at the input stage, which will greatly increase the device’s current draw. OUTPUT VOLTAGE 5V TO 2.5V 4.2 3.8 OUTPUT VOLTAGE 0V TO 2.5V 3.4 3.0 2.6 INPUT VOLTAGE EDGES 2.2 R 1.8 1.4 R 1.0 VIN – 0.6 5V 2.5V VO – 0.2 –0.2 0 10 20 30 40 50 60 01065-049 OUTPUT VOLTAGE (V) 3.2 70 TIME (ns) Figure 49. Overload Recovery, G = −1, VS = 5 V CAPACITIVE LOAD DRIVE The AD806x family is optimized for bandwidth and speed, not for driving capacitive loads. Output capacitance creates a pole in the amplifier’s feedback path, leading to excessive peaking and potential oscillation. If dealing with load capacitance is a requirement of the application, the two strategies to consider are as follows: 1. Use a small resistor in series with the amplifier’s output and the load capacitance. 2. Reduce the bandwidth of the amplifier’s feedback loop by increasing the overall noise gain. Rev. D | Page 15 of 20 AD8061/AD8062/AD8063 Figure 50 shows a unity-gain follower using the series resistor strategy. The resistor isolates the output from the capacitance and, more importantly, creates a zero in the feedback path that compensates for the pole created by the output capacitance. VCC 2V TO AMPLIFIER BIAS DISABLE 01065-050 VO CLOAD VIN VEE 01065-052 RSERIES AD8061 Figure 50. Series Resistor Isolating Capacitive Load Figure 52. Disable Circuit of the AD8063 Voltage feedback amplifiers like those in the AD806x family are able to drive more capacitive load without excessive peaking when used in higher gain configurations, because the increased noise gain reduces the bandwidth of the overall feedback loop. Figure 51 plots the capacitance that produces 30% overshoot vs. noise gain for a typical amplifier. Figure 34 shows the AD8063 supply current vs. DISABLE voltage. Figure 35 plots the output seen when the AD8063 input is driven with a 10 MHz sine wave, and the DISABLE is toggled from 0 V to 5 V, illustrating the part’s turn-on and turn-off time. Figure 33 shows the input/output isolation response with the AD8063 shut off. BOARD LAYOUT CONSIDERATIONS Maintaining the high speed performance of the AD806x family requires the use of high speed board layout techniques and low parasitic components. RS = 4.7 1k The PCB should have a ground plane covering unused portions of the component side of the board to provide a low impedance path. Remove the ground plane near the package to reduce parasitic capacitance. RS = 0 100 Proper bypassing is critical. Use a ceramic 0.1 μF chip capacitor to bypass both supplies. Locate the chip capacitor within 3 mm of each power pin. Additionally, connect in parallel a 4.7 μF to 10 μF tantalum electrolytic capacitor to provide charge for fast, large signal changes at the output. 01065-051 CAPACITIVE LOAD (pF) 10k 10 1 2 3 4 5 CLOSED-LOOP GAIN Figure 51. Capacitive Load vs. Closed-Loop Gain DISABLE OPERATION The internal circuit for the AD8063 disable function is shown in Figure 52. When the DISABLE node is pulled below 2 V from the positive supply, the supply current decreases from typically 6.5 mA to under 400 μA, and the AD8063 output will enter a high impedance state. If the DISABLE node is not connected and allowed to float, the AD8063 stays biased at full power. Minimizing parasitic capacitance at the amplifier’s inverting input pin is very important. Locate the feedback resistor close to the inverting input pin. The value of the feedback resistor may come into play—for instance, 1 kΩ interacting with 1 pF of parasitic capacitance creates a pole at 159 MHz. Use stripline design techniques for signal traces longer than 25 mm. Design them with either 50 Ω or 75 Ω characteristic impedance and proper termination at each end. Rev. D | Page 16 of 20 AD8061/AD8062/AD8063 APPLICATIONS SINGLE-SUPPLY SYNC STRIPPER When a video signal contains synchronization pulses, it is sometimes desirable to remove them prior to performing certain operations. In the case of A-to-D conversion, the sync pulses consume some of the dynamic range, so removing them increases the converter’s available dynamic range for the video information. Figure 53 shows a basic circuit for creating a sync stripper using the AD8061 powered by a single supply. When the negative supply is at ground potential, the lowest potential to which the output can go is ground. This feature is exploited to create a waveform whose lowest amplitude is the black level of the video and does not include the sync level. 0.1μF 7 2 AD8061 4 RG 1kΩ 75Ω 75Ω 75Ω 75Ω 75Ω 75Ω MONITOR #1 10μF 1kΩ 6 75Ω VIDEO OUT 3V 75Ω RF 1kΩ PIN NUMBERS ARE FOR 8-LEAD PACKAGE 1kΩ 3 10μF 0.1μF 7 2 AD8061 75Ω 6 RED 75Ω Figure 53. Single 3 V Sync Stripper Using AD8061 4 1kΩ In this case, the input video signal has its black level at ground, so it comes out at ground at the input. Since the sync level is below the black level, it will not show up at the output. However, all of the active video portion of the waveform will be amplified by a gain of two and then be normalized to unity gain by the backterminated transmission line. Figure 54 is an oscilloscope plot of the input and output waveforms. 3V MONITOR #2 10μF 0.1μF 8 1kΩ 2 3 1 AD8062 75Ω 75Ω 5 7 AD8062 1kΩ GREEN 75Ω BLUE 75Ω 6 1 1kΩ INPUT 4 01065-055 75Ω GREEN DAC 01065-053 3 RED DAC BLUE DAC 3V VIDEO IN The circuit can be modified to provide the sync stripping function for such a waveform. Instead of connecting RG to ground, connect it to a dc voltage that is two times the black level of the input signal. The gain from the +input to the output is two, which means the black level will be amplified by two to the output. However, the gain through RG is –unity to the output. It takes a dc level of twice the input black level to shift the black level to ground at the output. When this occurs, the sync will be stripped, and the active video will be passed as in the ground-referenced case. Figure 55. RGB Cable Driver Using AD8061 and AD8062 RGB AMPLIFIER 2 500mV 10μs 01065-054 OUTPUT Figure 54. Input and Output Waveforms for a Single-Supply Video Sync Stripper Using an AD8061 Some video signals with sync are derived from single-supply devices, such as video DACs. These signals can contain sync, but the whole waveform is positive, and the black level is not at ground but at some positive voltage. Most RGB graphics signals are created by video DAC outputs that drive a current through a resistor to ground. At the video black level, the current goes to zero, and the voltage of the video is also zero. Before the availability of high speed rail-to rail op amps, it was essential that an amplifier have a negative supply to amplify such a signal. Such an amplifier is necessary if one wants to drive a second monitor from the same DAC outputs. However, high speed, rail-to-rail output amplifiers like the AD8061 and AD8062 accept ground level input signals and output ground level signals. They are used as RGB signal amplifiers. A combination of the AD8061 (single) and the AD8062 (dual) amplifies the three video channels of an RGB system. Figure 55 shows a circuit that performs this function. Rev. D | Page 17 of 20 AD8061/AD8062/AD8063 MULTIPLEXER The AD8063 has a disable pin used to power down the amplifier to save power or to create a mux circuit. If two (or more) AD8063 outputs are connected together, and only one is enabled, then only the signal of the enabled amplifier will appear at the output. This configuration is used to select from various input signal sources. Additionally, the same input signal is applied to different gain stages, or differently tuned filters, to make a gainstep amplifier or a selectable frequency amplifier. Figure 56 shows a schematic of two AD8063s used to create a mux that selects between two inputs. One of these is a 1 V p-p, 3 MHz sine wave; the other is a 2 V p-p, 1 MHz sine wave. The SELECT signal and the output waveforms for this circuit are shown in Figure 57. For synchronization clarity, two different frequency synthesizers, whose time bases are locked to each other, generate the signals. 2μs OUTPUT SELECT 0.1μF 1V p-p 3MHz TIME BASE OUT 49.9Ω AD8063 1V 10μF Figure 57. AD8063 Mux Output 1 0.1μF 10μF –4V 1kΩ 49.9Ω 1kΩ +4V 49.9Ω 0.1μF 49.9Ω 2V p-p 1MHz AD8063 TIME BASE IN VOUT 10μF 1 0.1μF 10μF –4V 1kΩ HCO4 SELECT 01065-056 1kΩ Figure 56. Two-to-One Multiplexer Using Two AD8063s Rev. D | Page 18 of 20 2V 01065-057 +4V AD8061/AD8062/AD8063 OUTLINE DIMENSIONS 2.90 BSC 5 5.00 (0.1968) 4.80 (0.1890) 4 2.80 BSC 1.60 BSC 1 2 3 8 5 4.00 (0.1574) 3.80 (0.1497) 1 4 6.20 (0.2440) 5.80 (0.2284) PIN 1 0.95 BSC 1.90 BSC 1.30 1.15 0.90 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) 1.45 MAX 0.15 MAX 0.50 0.30 0.22 0.08 0.51 (0.0201) COPLANARITY SEATING 0.31 (0.0122) 0.10 PLANE 10° 5° 0° SEATING PLANE 0.60 0.45 0.30 COMPLIANT TO JEDEC STANDARDS MO-178AA Figure 58. 5-Lead Small Outline Transistor Package [SOT-23] (RT-5) Dimensions shown in millimeters 0.50 (0.0196) × 45° 0.25 (0.0099) 1.75 (0.0688) 1.35 (0.0532) 8° 0.25 (0.0098) 0° 1.27 (0.0500) 0.40 (0.0157) 0.17 (0.0067) COMPLIANT TO JEDEC STANDARDS MS-012AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN Figure 59. 8-Lead Standard Small Outline Package [SOIC] Narrow Body (R-8) Dimensions shown in millimeters and (inches) 2.90 BSC 6 5 3.00 BSC 4 2.80 BSC 1.60 BSC 8 1 2 3 3.00 BSC PIN 1 INDICATOR 1 5 4.90 BSC 4 0.95 BSC 1.30 1.15 0.90 1.90 BSC PIN 1 0.65 BSC 1.45 MAX 0.15 MAX 0.50 0.30 SEATING PLANE 1.10 MAX 0.15 0.00 0.22 0.08 10° 4° 0° 0.60 0.45 0.30 COMPLIANT TO JEDEC STANDARDS MO-178AB 0.38 0.22 COPLANARITY 0.10 0.23 0.08 8° 0° SEATING PLANE COMPLIANT TO JEDEC STANDARDS MO-187AA Figure 60. 6-Lead Small Outline Transistor Package [SOT-23] (RT-6) Dimensions shown in millimeters Rev. D | Page 19 of 20 Figure 61. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters 0.80 0.60 0.40 AD8061/AD8062/AD8063 ORDERING GUIDE Model AD8061AR AD8061AR-REEL AD8061AR-REEL7 AD8061ARZ 1 AD8061ARZ-REEL1 AD8061ARZ-REEL71 AD8061ART-R2 AD8061ART-REEL AD8061ART-REEL7 AD8061ARTZ-R21 AD8061ARTZ-REEL1 AD8061ARTZ-REEL71 AD8062AR AD8062AR-REEL AD8062AR-REEL7 AD8062ARZ1 AD8062ARZ-RL1 AD8062ARZ-R71 AD8062ARM AD8062ARM-REEL AD8062ARM-REEL7 AD8062ARMZ 3 AD8062ARMZ-RL3 AD8062ARMZ-R73 AD8063AR AD8063AR-REEL AD8063AR-REEL7 AD8063ARZ1 AD8063ARZ-REEL1 AD8063ARZ-REEL71 AD8063ART-R2 AD8063ART-REEL AD8063ART-REEL7 AD8063ARTZ-R21 AD8063ARTZ-REEL1 AD8063ARTZ-REEL71 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C –40°C to +85°C −40°C to +85°C −40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C 40°C to +85°C 40°C to +85°C 40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C Package Description 8-Lead SOIC 8-Lead SOIC, 13-Inch Tape and Reel 8-Lead SOIC, 7-Inch Tape and Reel 8-Lead SOIC 8-Lead SOIC, 13-Inch Tape and Reel 8-Lead SOIC, 7-Inch Tape and Reel 5-Lead SOT-23, 250 piece Tape and Reel 5-Lead SOT-23, 13-Inch Tape and Reel 5-Lead SOT-23, 7-Inch Tape and Reel 5-Lead SOT-23, 250 piece Tape and Reel 5-Lead SOT-23, 13-Inch Tape and Reel 5-Lead SOT-23, 7-Inch Tape and Reel 8-Lead SOIC 8-Lead SOIC, 13-Inch Tape and Reel 8-Lead SOIC, 7-Inch Tape and Reel 8-Lead SOIC 8-Lead SOIC, 13-Inch Tape and Reel 8-Lead SOIC, 7-Inch Tape and Reel 8-Lead MSOP 8-Lead MSOP, 13-Inch Tape and Reel 8-Lead MSOP, 7-Inch Tape and Reel 8-Lead MSOP 8-Lead MSOP, 13-Inch Tape and Reel 8-Lead MSOP, 7-Inch Tape and Reel 8-Lead SOIC 8-Lead SOIC, 13-Inch Tape and Reel 8-Lead SOIC, 7-Inch Tape and Reel 8-Lead SOIC 8-Lead SOIC, 13-Inch Tape and Reel 8-Lead SOIC, 7-Inch Tape and Reel 6-Lead SOT-23, 250 Piece Tape and Reel 6-Lead SOT-23, 13-Inch Tape and Reel 6-Lead SOT-23, 7-Inch Tape and Reel 6-Lead SOT-23, 250 Piece Tape and Reel 6-Lead SOT-23, 13-Inch Tape and Reel 6-Lead SOT-23, 7-Inch Tape and Reel 1 Z = Pb-free part. New branding after data code 0542, previously branded HGA. 3 Z = Pb-free part, # denotes lead-free product may be top or bottom marked. 4 New branding after data code 0542, previously branded HHA. 2 © 2005 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C01065-0-12/05(D) Rev. D | Page 20 of 20 Package Option R-8 R-8 R-8 R-8 R-8 R-8 RT-5 RT-5 RT-5 RT-5 RT-5 RT-5 R-8 R-8 R-8 R-8 R-8 R-8 RM-8 RM-8 RM-8 RM-8 RM-8 RM-8 R-8 R-8 R-8 R-8 R-8 R-8 RT-6 RT-6 RT-6 RT-6 RT-6 RT-6 Branding HGA HGA HGA H0D 2 H0D2 H0D2 HCA HCA HCA #HCA #HCA #HCA HHA HHA HHA H0E 4 H0E4 H0E4