Series AM1DR-NZ 1 Watt | DC-DC Converter FEATURES: • • • • • • • • RoHS compliant Regulated output voltage Low ripple and noise High efficiency up to 73% o o Operating temperature -40 C to + 85 C Input / Output Isolation 1000 & 3000VDC Pin computable with multiple manufacturers UL94-VO Package Models Single output Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Efficiency (%) AM1DR-0505S-NZ AM1DR-0509S-NZ AM1DR-0512S-NZ AM1DR-0515S-NZ AM1DR-1205S-NZ AM1DR-1209S-NZ AM1DR-1212S-NZ AM1DR-1215S-NZ AM1DR-2405S-NZ AM1DR-2409S-NZ AM1DR-2412S-NZ AM1DR-2415S-NZ 4.75-5.25 4.75-5.25 4.75-5.25 4.75-5.25 11.4-12.6 11.4-12.6 11.4-12.6 11.4-12.6 22.8-25.2 22.8-25.2 22.8-25.2 22.8-25.2 5 9 12 15 5 9 12 15 5 9 12 15 150 111 84 67 150 111 84 67 150 111 84 67 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 69 70 71 72 69 71 72 72 70 72 73 73 AM1DR-0505SH30-NZ 4.75-5.25 5 150 3000 68 Model Input Specifications Parameters Voltage range Nominal Typical 5 12 24 4.75-5.25 11.4-12.6 22.8-25.2 Maximum Units VDC Filter Capacitor Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Conditions Typical 60 sec Rated Units 1000 & 3000 VDC MOhm pF Maximum Units >1000 60 Output Specifications Parameters Voltage accuracy Short Circuit protection Line voltage regulation (Single) Load voltage regulation (Single) Temperature coefficient Ripple & Noise Conditions Typical ±3 % Momentary (1sec) Input voltage: ±5% 10-100% ±0.25 ±1 ±0.03 50 % % o %/ C mV p-p General Specifications Parameters Switching frequency Operating temperature Storage temperature Cooling Humidity www.aimtec.com F 051e R6.E Conditions Typical 100% load o Derating above 71 C Maximum -40 to +85 -55 to +125 Free air convection 95 Tel: +1 514 620 2722 1 of 2 Units KHz o C o C 100 % Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1DR-NZ 1 Watt | DC-DC Converter General Specifications (continued) Parameters Conditions Typical Maximum Units Plastic UL94-VO Case material g Weight 2.7 0.77 x 0.24 x 0.37 inch 19.60 x 6.00 x 9.50 mm Dimensions (L x W x H) o MTBF >900 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C) NOTE: All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Pin Out Specification Pin Single 1000 & 3000VDC 1 2 4 5 6 7 + V Input - V Input - V Output No pin + V Output No pin Dimensions 19.60 (0.77) 6.00 (0.24) PRINTED FACE 10.0 (0.39) 9.50 (0.37) 0.50 (0.02) 4.10 (0.16) 2.54 (0.10) 15.20 (0.60) External capacitor Vin (VDC) External capacitor (uF) Vout (VDC) External capacitor (uF) 5 12 24 - 4.7 2.2 1 - 5 9 12 15 10 4.7 2.2 1 0.50 (0.02) 6.00 (0.24) 0.50 (0.02) 0.25 (0.01) 1.25 (0.05) Filtering Derating Free Air Convection Output Power (% Max) 100 71ºC 80 Safe Operating Area 60 40 20 0 -40 -20 0 20 40 60 80 85 100 Ambient Temperature º C NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R6.E Tel: +1 514 620 2722 2 of 2 Toll free: + 1 888 9 AIMTEC (924 6832) North America only