BCD AP2213D-3.3TRE1 500ma low noise ldo regulator Datasheet

Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
General Description
Features
The AP2213 is a 500mA output current fixed voltage
regulator which provides low noise, very low dropout
voltage (typically 350mV at 500mA), very low
standby current (1µA maximum) and excellent power
supply ripple rejection (PSRR 75dB at 100Hz) in battery powered applications, such as handsets and PDAs
and in noise sensitive applications, such as RF electronics.
·
·
·
Up to 500mA Output Current
Low Standby Current
Low Dropout Voltage: VDROP=350mV at 500mA
·
·
High Output Accuracy: ±1%
Good Ripple Rejection Ability: 75dB at 100Hz
and IOUT=100µA
·
·
·
·
·
·
Tight Load and Line Regulation
Low Temperature Coefficient
Over Current Protection
Thermal Protection
Reversed-battery Protection
Logic-controlled Enable
The AP2213 features individual logic compatible
enable/shutdown control inputs, a low power shutdown mode for extended battery life, over current protection, over temperature protection, as well as
reversed-battery protection.
Applications
The AP2213 has 2.5V, 3.0V and 3.3V versions.
·
·
·
·
The AP2213 is available in TO-252-2 (1) and SOIC-8
packages.
Laptop, Notebook, and Palmtop Computer
CD-ROM, CD-R/RW, DVD Driver
Portable Electronic
PC Peripheral
SOIC-8
TO-252-2 (1)
Figure 1. Package Types of AP2213
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
1
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Pin Configuration
D Package
M Package
(SOIC-8)
(TO-252-2 (1))
3
VOUT
2
GND
1
VIN
EN
1
8
GND
VIN
2
7
GND
VOUT
3
6
GND
BYP
4
5
GND
Figure 2. Pin Configuration of AP2213 (Top View)
Pin Description
Pin Number
Pin Name
Function
TO-252-2 (1)
SOIC-8
3
3
VOUT
Regulated output voltage
2
5, 6, 7, 8
GND
Ground
1
2
VIN
Input Voltage
1
EN
Enable input: CMOS or TTL compatible input. Logic high=enable,
logic low=shutdown
4
BYP
Bypass capacitor for low noise operation
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
2
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Functional Block Diagram
VIN
BYP
3 (3)
1 (2)
VOUT
(4)
+
EN
Bandgap
Ref.
A (B)
A for TO-252-2 (1)
B for SOIC-8
(1)
Current Limit
Thermal Shutdown
2 (5, 6, 7, 8)
GND
Figure 3. Functional Block Diagram of AP2213
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
3
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Ordering Information
AP2213
E1: Lead Free
Circuit Type
TR: Tape and Reel
Blank: Tube
Package
D: TO-252-2 (1)
M: SOIC-8
Package
Temperature Range
2.5: Fixed Output 2.5V
3.0: Fixed Output 3.0V
3.3: Fixed Output 3.3V
Part Number
AP2213D-2.5E1
TO-252-2 (1)
SOIC-8
-40 to 125oC
-40 to 125oC
Marking ID
Packing Type
AP2213D-2.5E1
Tube
AP2213D-2.5TRE1
AP2213D-2.5E1
Tape & Reel
AP2213D-3.0E1
AP2213D-3.0E1
Tube
AP2213D-3.0TRE1
AP2213D-3.0E1
Tape & Reel
AP2213D-3.3E1
AP2213D-3.3E1
Tube
AP2213D-3.3TRE1
AP2213D-3.3E1
Tape & Reel
AP2213M-2.5E1
2213M-2.5E1
Tube
AP2213M-2.5TRE1
2213M-2.5E1
Tape & Reel
AP2213M-3.0E1
2213M-3.0E1
Tube
AP2213M-3.0TRE1
2213M-3.0E1
Tape & Reel
AP2213M-3.3E1
2213M-3.3E1
Tube
AP2213M-3.3TRE1
2213M-3.3E1
Tape & Reel
BCD Semiconductor's Pb-free products, as designated with "E1" suffix in the part number, are RoHS compliant.
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
4
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Absolute Maximum Ratings (Note 1)
Parameter
Symbol
Value
Unit
Supply Input Voltage
VIN
20
V
Enable Input Voltage
VEN
20
V
PD
Internally Limited (Thermal Protection)
W
TLEAD
260
o
Junction Temperature
TJ
150
oC
Storage Temperature
TSTG
-65 to 150
oC
ESD (Machine Model)
ESD
300
V
Thermal Resistance (No Heatsink)
θJA
Power Dissipation
Lead Temperature (Soldering, 10sec)
C
TO-252-2 (1)
90
SOIC-8
160
oC/W
Note 1: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to
the device. These are stress ratings only, and functional operation of the device at these or any other conditions
beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended periods may affect device reliability.
Recommended Operating Conditions
Parameter
Symbol
Min
Max
Unit
Supply Input Voltage
VIN
2.5
18
V
Enable Input Voltage
VEN
0
18
V
TJ
-40
125
oC
Operating Junction Temperature
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
5
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Electrical Characteristics
AP2213-2.5 Electrical Characteristics
VIN=3.5V, IOUT=100µA, CIN=1.0µF, COUT=2.2µF, VEN≥2.0V, TJ=25oC, Bold typeface applies over -40oC≤TJ≤125oC (Note 2),
unless otherwise specified.
Parameter
Output Voltage Accuracy
Output Voltage
Temperature Coefficient
(Note 3)
Line Regulation
Symbol
∆VOUT/VOUT
Conditions
Variation from specified
VOUT
Min
Typ
Max
-1
1
-2
2
%
∆VOUT/∆T
120
µV/oC
(∆VOUT/VOUT)/∆T
48
ppm/oC
VRLINE
1.5
VIN=3.5V to 13.2V
4.5
12
Load Regulation
(Note 4)
Unit
VRLOAD
IOUT=0.1mA to 500mA
1
7
17
15
IOUT=100µA
mV
mV
50
70
110
IOUT=50mA
150
230
140
IOUT=100mA
Dropout Voltage (Note 5)
250
300
VDROP
165
IOUT=150mA
mV
275
350
250
IOUT=300mA
400
500
350
IOUT=500mA
600
700
Standby Current
ISTD
VEN≤0.4V (shutdown)
0.01
VEN≤0.18V (shutdown)
1
µA
5
VEN≥2.0V, IOUT=100µA
100
VEN≥2.0V, IOUT=50mA
350
150
180
µA
600
800
Ground Pin Current
(Note 6)
IGND
VEN≥2.0V, IOUT=150mA
1.3
1.9
2.5
VEN≥2.0V, IOUT=300mA
4
VEN≥2.0V, IOUT=500mA
11
10
mA
15
20
28
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
6
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Electrical Characteristics (Continued)
AP2213-2.5 Electrical Characteristics
VIN=3.5V, IOUT=100µA, CIN=1.0µF, COUT=2.2µF, VEN≥2.0V, TJ=25oC, Bold typeface applies over -40oC≤TJ≤125oC (Note 2),
unless otherwise specified.
Parameter
Symbol
Conditions
Min
Typ
Ripple Rejection
PSRR
f=100Hz, IOUT=100µA
75
Current Limit
ILIMIT
VOUT=0V
700
Output Noise
eno
IOUT=50mA, COUT=2.2µF,
100pF from BYP to GND
260
Enable Input Logic-low
Voltage
VIL
Regulator shutdown
Enable Input Logic-high Voltage
VIH
Enable Input Logic-low Current
IIL
Enable Input Logic-high Current
Max
Unit
dB
1000
mA
nV / Hz
0.4
V
0.18
IIH
Regulator enabled
VIL≤0.4V
2.0
V
0.01
VIL≤0.18V
VIL≥2.0V
µA
2
5
VIL≥2.0V
1
20
µA
25
Note 2: Specifications in bold type are limited to -40oC≤TJ≤125oC. Limits over temperature are guaranteed by design, but not
tested in production.
Note 3: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature
range.
Note 4: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load
regulation in the load range from 0.1mA to 500mA. Changes in output voltage due to heating effects are covered by the thermal
regulation specification.
Note 5: Dropout voltage is defined as the input to output differential at which the output voltage drops 1% (TJ=25oC) or 2% (40oC≤TJ≤125oC) below its nominal value measured at 1V differential.
Note 6: Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
7
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Electrical Characteristics (Continued)
AP2213-3.0 Electrical Characteristics
VIN=4V, IOUT=100µA, CIN=1.0µF, COUT=2.2µF, VEN≥2.0V, TJ=25oC, Bold typeface applies over -40oC≤TJ≤125oC (Note 2),
unless otherwise specified.
Parameter
Output Voltage Accuracy
Output Voltage
Temperature Coefficient
(Note 3)
Line Regulation
Symbol
∆VOUT/VOUT
Conditions
Variation from specified
VOUT
Min
Typ
Max
-1
1
-2
2
%
∆VOUT/∆T
120
µV/oC
(∆VOUT/VOUT)/∆T
40
ppm/oC
VRLINE
1.5
VIN=4V to 13.2V
4.5
12
Load Regulation
(Note 4)
Unit
VRLOAD
IOUT=0.1mA to 500mA
1
8
17
15
IOUT=100µA
mV
mV
50
70
110
IOUT=50mA
150
230
140
IOUT=100mA
Dropout Voltage (Note 5)
250
300
VDROP
165
IOUT=150mA
mV
275
350
250
IOUT=300mA
400
500
350
IOUT=500mA
600
700
Standby Current
ISTD
VEN≤0.4V (shutdown)
0.01
VEN≤0.18V (shutdown)
VEN≥2.0V, IOUT=100µA
1
100
150
180
VEN≥2.0V, IOUT=50mA
µA
5
350
µA
600
800
Ground Pin Current
(Note 6)
IGND
VEN≥2.0V, IOUT=150mA
1.3
1.9
2.5
VEN≥2.0V, IOUT=300mA
4
10
mA
15
VEN≥2.0V, IOUT=500mA
11
20
28
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
8
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Electrical Characteristics (Continued)
AP2213-3.0 Electrical Characteristics
VIN=4V, IOUT=100µA, CIN=1.0µF, COUT=2.2µF, VEN≥2.0V, TJ=25oC, Bold typeface applies over -40oC≤TJ≤125oC (Note 2),
unless otherwise specified.
Parameter
Symbol
Conditions
Min
Typ
Ripple Rejection
PSRR
f=100Hz, IOUT=100µA
75
Current Limit
ILIMIT
VOUT=0V
700
Output Noise
eno
IOUT=50mA, COUT=2.2µF,
100pF from BYP to GND
260
Enable Input Logic-low
Voltage
VIL
Regulator shutdown
Enable Input Logic-high Voltage
VIH
Enable Input Logic-low Current
IIL
Enable Input Logic-high Current
Max
Unit
dB
1000
mA
nV / Hz
0.4
V
0.18
IIH
Regulator enabled
VIL≤0.4V
2.0
V
0.01
VIL≤0.18V
VIL≥2.0V
VIL≥2.0V
1
µA
2
5
20
µA
25
Note 2: Specifications in bold type are limited to -40oC≤TJ≤125oC. Limits over temperature are guaranteed by design, but not
tested in production.
Note 3: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature
range.
Note 4: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load
regulation in the load range from 0.1mA to 500mA. Changes in output voltage due to heating effects are covered by the thermal
regulation specification.
Note 5: Dropout voltage is defined as the input to output differential at which the output voltage drops 1% (TJ=25oC) or 2% (40oC≤TJ≤125oC) below its nominal value measured at 1V differential.
Note 6: Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the
supply is the sum of the load current plus the ground pin current.
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
9
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Electrical Characteristics (Continued)
AP2213-3.3 Electrical Characteristics
VIN=4.3V, IOUT=100µA, CIN=1.0µF, COUT=2.2µF, VEN≥2.0V, TJ=25oC, Bold typeface applies over -40oC≤TJ≤125oC (Note 2),
unless otherwise specified.
Parameter
Output Voltage Accuracy
Output Voltage
Temperature Coefficient
(Note 3)
Line Regulation
Symbol
∆VOUT/VOUT
Conditions
Variation from specified
VOUT
Min
Typ
Max
-1
1
-2
2
%
∆VOUT/∆T
120
µV/oC
(∆VOUT/VOUT)/∆T
36.3
ppm/oC
VRLINE
1.5
VIN=4.3V to 13.2V
4.5
12
Load Regulation
(Note 4)
Unit
VRLOAD
IOUT=0.1mA to 500mA
1
9
18
15
IOUT=100µA
mV
mV
50
70
110
IOUT=50mA
150
230
140
IOUT=100mA
Dropout Voltage (Note 5)
250
300
VDROP
165
IOUT=150mA
mV
275
350
250
IOUT=300mA
400
500
350
IOUT=500mA
600
700
Standby Current
ISTD
VEN≤0.4V (shutdown)
0.01
VEN≤0.18V (shutdown)
VEN≥2.0V, IOUT=100µA
1
100
150
180
VEN≥2.0V, IOUT=50mA
µA
5
350
µA
600
800
Ground Pin Current
(Note 6)
IGND
VEN≥2.0V, IOUT=150mA
1.3
1.9
2.5
VEN≥2.0V, IOUT=300mA
4
10
mA
15
VEN≥2.0V, IOUT=500mA
11
20
28
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
10
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Electrical Characteristics (Continued)
AP2213-3.3 Electrical Characteristics
VIN=4.3V, IOUT=100µA, CIN=1.0µF, COUT=2.2µF, VEN≥2.0V, TJ=25oC, Bold typeface applies over -40oC≤TJ≤125oC (Note 2),
unless otherwise specified.
Parameter
Symbol
Conditions
Min
Typ
Ripple Rejection
PSRR
f=100Hz, IOUT=100µA
75
Current Limit
ILIMIT
VOUT=0V
700
Output Noise
eno
IOUT=50mA, COUT=2.2µF,
100pF from BYP to GND
260
Enable Input Logic-low
Voltage
VIL
Regulator shutdown
Enable Input Logic-high Voltage
VIH
Enable Input Logic-low Current
IIL
Enable Input Logic-high Current
Max
Unit
dB
1000
mA
nV / Hz
0.4
V
0.18
IIH
Regulator enabled
VIL≤0.4V
2.0
V
0.01
VIL≤0.18V
VIL≥2.0V
VIL≥2.0V
1
µA
2
5
20
µA
25
Note 2: Specifications in bold type are limited to -40oC≤TJ≤125oC. Limits over temperature are guaranteed by design, but not
tested in production.
Note 3: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature
range.
Note 4: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load
regulation in the load range from 0.1mA to 500mA. Changes in output voltage due to heating effects are covered by the thermal
regulation specification.
Note 5: Dropout voltage is defined as the input to output differential at which the output voltage drops 1% (TJ=25oC) or 2% (40oC≤TJ≤125oC) below its nominal value measured at 1V differential.
Note 6: Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the
supply is the sum of the load current plus the ground pin current.
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
11
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Typical Performance Characteristics
850
2.502
800
Output Voltage (V)
2.498
IOUT=50mA
750
700
IOUT=100mA
CIN=1µF, COUT=2.2µF
650
IOUT=150mA
600
IOUT=300mA
550
IOUT=500mA
Dropout Voltage (mV)
2.500
AP2213-2.5
VIN=3.5V, IOUT=10mA
2.496
2.494
2.492
2.490
500
CIN=1µF, COUT=2.2µF
450
400
350
300
250
2.488
200
150
2.486
2.484
-60
100
-40
-20
0
20
40
60
80
100
120
50
-60
140
-40
-20
20
40
60
80
100
120
140
Junction Temperature ( C)
Figure 4. Output Voltage vs. Junction Temperature
Figure 5. Dropout Voltage vs. Junction Temperature
20
10
9
18
o
TA=25 C
CIN=1µF, COUT=2.2µF
8
Ground Pin Current (mA)
Ground Pin Current (mA)
0
o
o
Junction Temperature ( C)
7
6
5
4
3
IOUT=300mA
IOUT=500mA
10
8
6
2
200
300
400
0
-60
500
IOUT=150mA
12
1
100
IOUT=100mA
14
4
0
IOUT=50mA
16
2
0
AP2213-2.5
VIN=3.5V, CIN=1µF, COUT=2.2µF
-40
-20
0
20
40
60
80
100
120
140
0
Junction Temperature ( C)
Output Current (mA)
Figure 6. Ground Pin Current vs. Output Current
Figure 7. Ground Pin Current vs. Junction Temperature
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
12
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Typical Performance Characteristics (Continued)
1.8
13
12
AP2213-2.5, VIN=3.5V
1.7
CIN=1µF, COUT=2.2µF, IOUT=100µA
1.6
AP2213-2.5
CIN=1µF, COUT=2.2µF
1.5
IOUT=100µA, VIN=3.5V
VEN=1.8V
10
VEN=2V
9
VEN=3V
8
VEN=3.7V
Enable Voltage (V)
Enable Current (µA)
11
7
6
5
1.4
1.3
1.2
1.1
1.0
VEN=logic high
0.9
VEN=logic low
0.8
4
0.7
3
0.6
2
-60
-40
-20
0
20
40
60
80
100
120
0.5
-60
140
-40
-20
0
20
60
80
100
120
140
Junction Temperature ( C)
Figure 9. Enable Voltage vs. Junction Temperature
Figure 8. Enable Current vs. Junction Temperature
100
200
AP2213-2.5
IOUT=10mA, CIN=1µF, COUT=2.2µF
IOUT=10mA
CIN=1µF, COUT=2.2µF
Output Noise ( µV/ Hz)
10
Noise Measurement Filter: DIN Noise
150
Noise (µVrms)
40
o
o
Junction Temperature ( C)
100
VIN=3.5V, CBYP=100pF
1
0.1
0.01
50
0.001
0
10
100
1000
0.0001
10
10000
100
1k
10k
100k
1M
10M
Frequency (Hz)
Bypass Capacitor (pF)
Figure 10. Noise vs. Bypass Capacitor
Figure 11. Output Noise vs. Frequency
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
13
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Typical Performance Characteristics (Continued)
5.5
VIN (1V/Div)
AP2213-2.5
0.5
0
10mA
∆VOUT (10mV/Div)
-0.5
∆VOUT (10mV/Div)
IOUT (0.5A/Div)
1
0
-10
-20
AP2213-2.5
4.5
3.5
2.5
10
0
-10
-20
-30
Time (200µs/Div)
Time (200µs/Div)
Figure 13. Line Transient
(Conditions: VIN=3.4 to 4.4V, VEN=2V, IOUT=100µA,
CBYP=100pF, COUT=2.2µF)
Figure 12. Load Transient
(Conditions: VIN=3.5V, CBYP=100pF, VEN=2V,
IOUT=10 to 500mA, CIN=1µF, COUT=2.2µF)
3
100
VOUT (1V/Div)
AP2213-2.5
VIN=3.5V, VRIPPLE=1VPP
90
2
80
1
IOUT=10mA, COUT=2.2µF
70
0
PSRR (dB)
VEN (1V/Div)
AP2213-2.5
60
50
40
2
30
1
20
0
10
0
10
-1
100
1k
10k
100k
1M
Frequency (Hz)
Time (40µs/Div)
Figure 15. PSRR vs. Frequency
Figure 14. VEN vs. VOUT
(Conditions: VEN=0 to 2V, VIN=3.5V, IOUT=30mA,
CBYP=open, CIN=1µF, COUT=2.2µF)
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
14
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Typical Performance Characteristics (Continued)
1.4
1.4
TO-252-2(1) Package
No Heatsink
SOIC-8 Package
No Heatsink
1.2
Power Dissipation (W)
Power Dissipation (W)
1.2
1.0
0.8
0.6
0.4
1.0
0.8
0.6
0.4
0.2
0.2
0.0
25
50
75
100
125
0.0
25
150
50
75
100
150
Ambient Temperature ( C)
Figure 16. Power Dissipation vs. Ambient Temperature
Figure 17. Power Dissipation vs. Ambient Temperature
1000
1000
COUT=2.2µF
COUT=1µF
No Bypass Capacitor
100
10
Stable Area
1
No Bypass Capacitor
100
ESR (Ω)
ESR (Ω)
125
o
o
Ambient Temperature ( C)
10
Stable Area
1
0.1
0.1
0.01
0.01
0
50
100
150
200
250
300
350
400
450
0
500
50
100
150
200
250
300
350
400
450
500
Output Current (mA)
Output Current (mA)
Figure 18. ESR vs. Output Current
Figure 19. ESR vs. Output Current
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
15
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Typical Performance Characteristics (Continued)
1000
COUT=4.7µF
No Bypass Capacitor
ESR (Ω)
100
10
Stable Area
1
0.1
0.01
0
50
100
150
200
250
300
350
400
450
500
Output Current (mA)
Figure 20. ESR vs. Output Current
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
16
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Typical Application
VIN=3.5V
VIN
AP2213-2.5
VIN
VOUT
VOUT=2.5V
VOUT
EN
CIN
GND
BYP
1µF
COUT
2.2µF
CBYP
100pF
Figure 21. Typical Application of AP2213 (Note 7)
Note 7: Dropout voltage is 350mV when TA=25oC. In order to obtain a normal output voltage, VOUT+0.35V is the minimum
input voltage which will results a low PSRR, imposing a bad influence on system. Therefore, the recommended input voltage
is VOUT+1V to 18V. For AP2213-2.5 version, its input voltage can be set from 3.5V(VOUT+1V) to 18V.
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
17
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Application Information
To determine if the power dissipated in the regulator
reaches the maximum power dissipation (see figure
16, 17), using:
TJ = PD*θJA + TA
PD=(VIN-VOUT)*IOUT+VIN*IGND
Input Capacitor
A 1µF minimum capacitor is recommended to be
placed between VIN and GND.
Output Capacitor
It is required to prevent oscillation. 1µF minimum is
recommended when CBYP is unused. 2.2µF minimum is recommended when CBYP is 100pF. The output capacitor may be increased to improve transient
response.
Where: TJ≤TJ(max), TJ(max) is absolute maximum ratings for the junction temperature; VIN*IGND can be
ignored due to its small value.
TJ(max) is 150oC, θJA is 90oC/W for TO-252-2 (1)
package and 160oC/W for SOIC-8 package.
Noise Bypass Capacitor
Bypass capacitor is connected to the internal voltage
reference. A 100pF capacitor connected from BYP to
GND make this reference quiet, resulting in a
significant reduction in output noise, but the ESR
stable area will be narrowed.
Example: For 2.5V version packaged in SOIC-8,
IOUT=500mA, TA=50oC, VIN(Max) is:
(150oC-50oC)/(0.5A*160oC/W)+2.5V=3.75V
The start-up speed of the AP2213 is inversely
proportional to the value of reference bypass
capacitor. In some cases, if output noise is not a
major concern and rapid turn-on is necessary, omit
CBYP and leave BYP open.
Therefore, for good performance, please make sure
that input voltage is less than 3.75V without heatsink
when TA=50oC.
Power Dissipation
Thermal shutdown may take place if exceeding the
maximum power dissipation in application. Under all
possible operating conditions, the junction temperature must be within the range specified under absolute maximum ratings to avoid thermal shutdown.
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
18
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Mechanical Dimensions
1.350(0.053)
1.650(0.065)
TO-252-2(1)
6.350(0.250)
6.650(0.262)
5.200(0.205)
5.400(0.213)
Unit: mm(inch)
2.200(0.087)
2.400(0.094)
0.430(0.017)
0.580(0.023)
4.300(0.169)
5.400(0.212)
5°
0.700(0.028)
0.900(0.035)
0.500(0.020)
0.700(0.028)
2.300TYP
4.500(0.177)
4.700(0.165)
1.400(0.055)
1.780(0.070)
5°
3°
4°
0.430(0.017)
0.580(0.023)
Mar. 2007 Rev. 1. 2
4.800(0.189)
6.500(0.256)
3.800REF(0.150REF)
5.400(0.213)
5.700(0.224)
0.000(0.000)
0.127(0.005)
2.550(0.100)
2.900(0.114)
0.600(0.024)
0.900(0.035)
9.500(0.374)
9.900(0.390)
8°
BCD Semiconductor Manufacturing Limited
19
Data Sheet
500mA LOW NOISE LDO REGULATOR
AP2213
Mechanical Dimensions (Continued)
SOIC-8
4.700(0.185)
5.100(0.201)
7°
Unit: mm(inch)
0.320(0.013)
1.350(0.053)
1.750(0.069)
8°
8°
7°
0.675(0.027)
0.725(0.029)
D
5.800(0.228)
1.270(0.050)
6.200(0.244)
TYP
D
20:1
φ 0.800(0.031)
0.300(0.012)
R0.150(0.006)
0.100(0.004)
0.200(0.008)
0°
8°
1.000(0.039)
3.800(0.150)
4.000(0.157)
0.330(0.013)
0.190(0.007)
0.250(0.010)
1°
5°
0.510(0.020)
0.900(0.035)
R0.150(0.006)
0.450(0.017)
0.800(0.031)
Mar. 2007 Rev. 1. 2
BCD Semiconductor Manufacturing Limited
20
http://www.bcdsemi.com
IMPORTANT NOTICE
BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifications herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for use of any its products for any
particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any liability arising out of the application or use
of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or
other rights nor the rights of others.
MAIN SITE
BCD Semiconductor Manufacturing Limited
BCD Semiconductor Manufacturing Limited
- Wafer Fab
Shanghai SIM-BCD Semiconductor Manufacturing Limited
800, Yi Shan Road, Shanghai 200233, China
Tel: +86-21-6485 1491, Fax: +86-21-5450 0008
- IC Design Group
Advanced Analog Circuits (Shanghai) Corporation
8F, Zone B, 900, Yi Shan Road, Shanghai 200233, China
Tel: +86-21-6495 9539, Fax: +86-21-6485 9673
REGIONAL SALES OFFICE
Shenzhen Office
Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. Shenzhen Office
Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office
Room E, 5F, Noble Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China
Tel: +86-755-8826 7951
Fax: +86-755-8826 7865
Taiwan Office
BCD Semiconductor (Taiwan) Company Limited
4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei,
Taiwan
Tel: +886-2-2656 2808
Fax: +886-2-2656 2806
USA Office
BCD Semiconductor Corporation
30920 Huntwood Ave. Hayward,
CA 94544, U.S.A
Tel : +1-510-324-2988
Fax: +1-510-324-2788
Similar pages