ODIN MPR4 02 Fiber Optic Receiver for MOST® Data Sheet Description Features The 4-pin MOST Optical Receiver (ODIN MPR4 02) is a highly integrated CMOS IC combined with a high speed PIN diode designed to receive up to 25 Mbit/s optical data which is biphase coded (up to 50 Mbaud) and convert this optical data to a rail-to-rail data stream. During the low power mode, the PIN diode is still being observed and if activity is detected, the receiver will switch to full power mode. A STATUS-pin indicates if modulated light is received (Light on -> STATUS = low). With the STATUS-pin the power supply of the whole MOST device can be switched ON. The power supply voltage is either 3.3V or 5V. Excellent solution for converting high speed data from Plastic Optical Fiber (POF) to digital output. Applications • Pulse width control • Optical Receiver for MOST Systems • Operating @ 3.3V or 5V Power Supply • High speed receiver up to 25 Mbit/s net data rate (50 MBaud) • 95°C operating temperature over whole life time • Photo current sensing, network activity detection and Low Power Mode (ICC < 10 µA) • Signal detect and Status Output • Low power consumption • -25dBm guaranteed sensitivity @ 650nm for working in a low attenuation range of PMMA Fiber • Fully compliant to “MOST® Specification of Physical Layer Rev 1.1” • RoHS compliant (Lead free and halogen free) Table 1. Absolute Maximum Ratings Limit Values Parameter Symbol min. max. Unit Supply Voltage[1] VCCMax -0.5 6.0 V Storage Temperature Range TSTG -40 100 °C Soldering Temperature (>2.5 mm from case bottom t ≤ 10s) TS – 260 °C -0.5 VCC +0.5 V – 2.0 Voltage at any PIN Electrostatic Discharge Voltage Capability[2] ESD kV Notes: 1. Maximum supply voltage without causing damage 2. ESD Capability for all Pins HBM (human body model) according JESD22-A114B. Table 2. Recommended Operating Conditions Limit Values Parameter Symbol min. max. Unit Supply Voltage low VCC_l 3.135 3.465 V Supply Voltage high VCC_h 4.75 5.25 V Operating Temperature Range (ambient)[1] TA -40 95 °C Notes: 1. For details see application note “Handling, Storage, Operating and Processing Application Note of ODIN MOST4 Transceiver” All the data in this specification refers to the operating conditions above and over life time unless otherwise stated. Table 3. Optical Signal Characteristics (22.5 Mbit MOST Data, VCC = 3.135 … 3.465 V or 4.75 ... 5.25 V) Limit Values Parameter Symbol min. typ. max. Unit Peak wavelength of input signal λPeak 630 650 685 nm FWHM of input signal ∆λ – – 30 nm Receivable optical power range for data recovery[1][2] Popt -25 – -2 dBm Receivable optical power for switching to low power mode[1] POFF -40 – -25 dBm Notes: 1. Optical power data are average values when using a MxT4 xx optical transmitter, measured at the end of a plastic optical fiber with metal insert (diameter 2.90 +/- 0.02 mm). The transmitted data is biphase coded. 2. Measured with worst case pattern. A BER ≤10-9 can be reached. Attention Stresses above those listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Between 3.465V and 4.75V the device is not specified according Table 2. Therefore operation is limited to the range of 3.135V ... 3.465V or 4.75V ... 5.25V. Table 4.1 AC Electrical Characteristics 45Mbaud (44.1kHz) Limit Values Parameter Symbol min. typ. max. Unit Output Rise Time @ Vcc_l [1][4] tr_l – 6 9 ns Output Rise Time @ Vcc_h [1][4] tr_h – 5 9 ns Output Fall Time @ Vcc_l [1][4] tf_l – 6 9 ns Output Fall Time @ Vcc_h [1][4] tf_h – 5 9 ns Output Pulse Width Variation 1UI [1][2][3][4][5] tPWV 16.5 – 31.0 ns Output Average Pulse Width Distortion[1][2][3][4] tAPWD -3.3 – 7.0 ns Data Dependent Link Jitter[2][3][4] tDDJ – – 3.3 ns Uncorrelated Link Jitter[2][3][4] tUJ – – 1.0 ns Power-up time at detection of rising VCC tPUO – 0.1 6 ms Power-up time from low power mode tPU – 0.5 6 ms Low Power mode timer delay tLPM – 0.005 2 ms Notes: 1. Capacitive Load is max. 10pF. 2. MOST Data 44.1 kHz FS corresponds to a 45 MBaud data stream. 3. The optical input signal has to fulfill following requirements: tPWV(min) = 20.0 ns, tPWV(max) = 24.3 ns, tAPWD(min) = -1.4 ns and tAPWD(max) = 1.4 ns, tDDJ(max).= 0.77 ns, tUJ(max).= 0.33 ns, Positive Overshoot within 0UI...2/3UI = -20...40%, Extinction Ratio min = 10dB. Variation within those limits does not significantly change tPWV. 4. Characterized with Avago Characterization Boards as described in the Application note “Application Note MOST circuit for Avago ODIN Transceiver“. 5. Limits for 2UI are 38.6 ... 53.1ns and for 3UI they are 60.8 ... 75.2ns. Table 4.2 Electrical Characteristics 49.152MBaud (48kHz) Limit Values Parameter Symbol min. typ. max. Unit Output Rise Time @ Vcc_l [1][4] tr_l – 6 9 ns Output Rise Time @ Vcc_h [1][4] tr_h – 5 9 ns Output Fall Time @ Vcc_l [1][4] tf_l – 6 9 ns Output Fall Time @ Vcc_h [1][4] tf_h – 5 9 ns Output Pulse Width Variation 1UI [1][2][3][4][5] tPWV 15.1 – 28.5 ns Output Average Pulse Width Distortion[1][2][3][4] tAPWD -3.0 – 6.4 ns Data Dependent Link Jitter[2][3][4] tDDJ – – 3.1 ns Uncorrelated Link Jitter[2][3][4] tUJ – – 0.9 ns Power-up time at detection of rising VCC tPUO – 0.1 6 ms Power-up time from low power mode tPU – 0.5 6 ms Low Power mode timer delay tLPM – 0.005 2 ms Notes: 1. Capacitive Load is max. 10pF. 2. MOST Data 48kHz FS corresponds to a 49.152MBaud data stream. 3. The optical input signal has to fulfill following requirements: tPWV(min) = 18.37ns. tpwv(max) = 22.32ns, tAPWD(min) = -1.28ns, tAPWD(max) = 1.28ns, tDDJ(max) = 0.71ns and tUJ(max) = 0.3ns, Positive Overshoot within 0UI...2/3UI = -20...40%, Extinction Ratio min = 10dB. Variation within those limits does not significantly change tPWV. 4. Characterized with Avago Characterization Boards as described in the Application note “Application Note MOST circuit for Avago ODIN Transceiver“. 5. Limits for 2UI are 35.47 … 48.825ns and for 3UI are 55.81 … 69.17ns. Table 5. DC Electrical Characteristics Limit Values Parameter Symbol min. typ. max. Unit Supply Voltage low VCC_l 3.135 3.3 3.465 V Supply Voltage high VCC_h 4.75 5 5.25 V Low Level Output Voltage Data and Status Pin[1] VOL – – 0.4 V High Level Output Voltage Data Pin[1] VOH 2.5 3.3 3.7 V High Level Output Voltage Status Pin[1] VOH 2.5 – VCC V Supply Current Full Power Mode ICC,FPM – – 15 mA Supply Current LowPower Mode ICC,LPM – – 10 µA Notes: 1. Resistor load must not be smaller than 50kOhm Package Outlines (Cavity as Interface Package) Dimensions in mm For a more detailed drawing please contact Avago Technologies. Disclaimer The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved.We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Warnings Due to technical requirements components may contain dangerous substances. For information on the types inquestion please contact your nearest Avago Technologies Office. Avago Technologies Components may only be used in life-support devices or systems with the express written approval of Avago Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustainand/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons maybe endangered. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Avago Technologies Office (www.avagotech.com). Revision History Current Document: AV02-0745EN - November 6, 2007 Previous Version: AV02-0745EN - October 3, 2007 Page Subjects (major changes since last revision) 3 Additional specification for rise and fall time. Rounding of decimal places. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright © 2007 Avago Technologies Limited. All rights reserved. AV02-0745EN - November 6, 2007