Kingbright APT3216LZGCK Low power consumption Datasheet

3.2mmx1.6mm SMD CHIP LED LAMP
Part Number: APT3216LZGCK
Green
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z 3.2mmx1.6mm SMT LED, 0.75mm thickness.
z The Green source color devices are made with InGaN
on Sapphire Light Emitting Diode.
z Low power consumption.
z Electrostatic discharge and power surge could damage
z Wide viewing angle.
z Ideal for backlight and indicator.
the LEDs.
z It is recommended to use a wrist band or anti-
z Package : 2000pcs / reel.
z Moisture sensitivity level : level 3.
z Low current IF=2mA operating.
electrostatic glove when handling the LEDs.
z All devices, equipments and machineries must be
electrically grounded.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.2(0.008") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAN8404
REV NO: V.2B
DATE: MAR/09/2015
PAGE: 1 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203014471
Selection Guide
Part No.
Dice
APT3216LZGCK
Lens Type
Green (InGaN)
Water Clear
Viewing
Angle [1]
Iv (mcd) [2]
@ 2mA
Min.
Typ.
2θ1/2
20
50
120°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
λpeak
Peak Wavelength
Green
λD [1]
Dominant Wavelength
Δλ1/2
Min.
Typ.
Units
Test Conditions
515
nm
IF=2mA
Green
525
nm
IF=2mA
Spectral Line Half-width
Green
35
nm
IF=2mA
C
Capacitance
Green
45
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Green
3
V
IF=2mA
IR
Reverse Current
Green
50
uA
VR=5V
2.2
Max.
2.65
Notes:
1.Wavelength: +/-1nm.
2.Forward Voltage: +/-0.1V.
3.Wavelength value is traceable to the CIE127-2007 compliant national standards.
4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Green
Units
Power dissipation
75
mW
DC Forward Current
25
mA
Peak Forward Current [1]
150
mA
5
V
Reverse Voltage
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAN8404
REV NO: V.2B
DATE: MAR/09/2015
PAGE: 2 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203014471
Green
APT3216LZGCK
SPEC NO: DSAN8404
REV NO: V.2B
DATE: MAR/09/2015
PAGE: 3 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203014471
APT3216LZGCK
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAN8404
REV NO: V.2B
DATE: MAR/09/2015
PAGE: 4 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203014471
PACKING & LABEL SPECIFICATIONS
APT3216LZGCK
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAN8404
REV NO: V.2B
DATE: MAR/09/2015
PAGE: 5 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1203014471
Similar pages