TI1 ADS7806UB/1K Low-power 12-bit sampling cmos analog-to-digital converter Datasheet

ADS7806
ADS
780
6
ADS
780
6
SBAS021B – NOVEMBER 1992 – REVISED SEPTEMBER 2003
Low-Power 12-Bit Sampling CMOS
ANALOG-to-DIGITAL CONVERTER
FEATURES
DESCRIPTION
●
●
●
●
●
●
●
●
●
●
●
The ADS7806 is a low-power, 12-bit, sampling Analog-toDigital (A/D) converter using state of the art CMOS structures.
It contains a complete 12-bit, capacitor-based, Successive
Approximation Register (SAR) A/D converter with sampleand-hold, clock, reference, and a microprocessor interface with
parallel and serial output drivers.
POWER DISSIPATION: 35mW max
POWER-DOWN MODE: 50µW
ACQUISITION AND CONVERSION: 25µs max
±1/2 LSB MAX INL AND DNL
72dB MIN SINAD WITH 1kHz INPUT
INPUT RANGES: ±10V, 0V to +5V, and 0V TO +4V
SINGLE +5V SUPPLY OPERATION
PARALLEL AND SERIAL DATA OUTPUT
PIN-COMPATIBLE WITH THE 16-BIT ADS7807
USES INTERNAL OR EXTERNAL REFERENCE
0.3" DIP-28 AND SO-28
Clock
The ADS7806 can acquire and convert to full 12-bit accuracy
in 25µs max, while consuming only 35mW max. Laser
trimmed scaling resistors provide standard industrial input
ranges of ±10V and 0V to +5V. In addition, a 0V to +4V range
allows development of complete single-supply systems.
The ADS7806 is available in a 0.3" DIP-28 and SO-28, both
fully specified for operation over the industrial –40°C to
+85°C temperature range.
R/C
CS
BYTE
Power
Down
Successive Approximation Register and Control Logic
40kΩ
CDAC
R1IN
BUSY
Parallel
20kΩ
40kΩ
Serial Data
Clock
and
10kΩ
Comparator
R2IN
Serial
Serial Data
Data
CAP
Out
Parallel Data
Buffer
6kΩ
REF
8
Internal
+2.5V Ref
Reference
Power-Down
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright © 1992-2003, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ELECTROSTATIC
DISCHARGE SENSITIVITY
ABSOLUTE MAXIMUM RATINGS(1)
Analog Inputs: R1IN ............................................................................ ±12V
R2IN ........................................................................... ±5.5V
CAP ................................... VANA + 0.3V to AGND2 – 0.3V
REF .......................................... Indefinite Short to AGND2,
Momentary Short to VANA
Ground Voltage Differences: DGND, AGND1, and AGND2 ............. ±0.3V
VANA ....................................................................................................... 7V
VDIG to VANA ...................................................................................... +0.3V
VDIG ........................................................................................................ 7V
Digital Inputs ............................................................. –0.3V to VDIG + 0.3V
Maximum Junction Temperature ................................................... +165°C
Internal Power Dissipation ............................................................. 825mW
Lead Temperature (soldering, 10s) ............................................... +300°C
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings”
may cause permanent damage to the device. Exposure to absolute maximum
conditions for extended periods may affect device reliability.
PACKAGE/ORDERING INFORMATION
PRODUCT
MAXIMUM
INTEGRAL
LINEARITY
ERROR (LSB)
MINIMUM
SIGNAL-TOSPECIFIED
(NOISE + DISTORTION)
PACKAGE
TEMPERATURE
RATIO (DB)
PACKAGE-LEAD DESIGNATOR(1)
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
ADS7806P
ADS7806PB
±0.9
±0.45
70
72
DIP-28
NT
–40°C to +85°C
"
"
"
ADS7806P
ADS7806PB
ADS7806P
ADS7806PB
Tubes, 13
Tubes, 13
ADS7806U
"
±0.9
"
70
"
SO-28
"
DW
"
–40°C to +85°C
"
ADS7806U
ADS7806U
ADS7806U
ADS7806U/1K
Tubes, 28
Tape and Reel, 1000
ADS7806UB
"
±0.45
"
72
"
"
"
"
"
"
"
ADS7806UB
ADS7806UB
ADS7806UB
Tubes, 28
ADS7806UB/1K Tape and Reel, 1000
NOTE: (1) For the most current specifications and package information, refer to our web site at www.ti.com.
ELECTRICAL CHARACTERISTICS
At TA = –40°C to +85°C, fS = 40kHz, VDIG = VANA = +5V, and using internal reference and fixed resistors (see Figure 7b), unless otherwise specified.
ADS7806P, U
PARAMETER
CONDITIONS
MIN
TYP
RESOLUTION
DC ACCURACY
Integral Linearity Error
Differential Linearity Error
No Missing Codes
Transition Noise(2)
Gain Error
Full-Scale Error(3,4)
Full-Scale Error Drift
Full-Scale Error(3,4)
Full-Scale Error Drift
Bipolar Zero Error(3)
Bipolar Zero Error Drift
Unipolar Zero Error(3)
Unipolar Zero Error Drift
Recovery Time to Rated Accuracy
from Power-Down(5)
Power-Supply Sensitivity
(VDIG = VANA = VS)
2
MAX
MIN
TYP
12
ANALOG INPUT
Voltage Ranges
Impedance
Capacitance
THROUGHPUT SPEED
Conversion Time
Complete Cycle
Throughput Rate
ADS7806PB, UB
MAX
UNITS
✻
Bits
±10, 0 to +5, 0 to +4
(See Table I)
V
✻
35
20
25
Acquire and Convert
±0.15
±0.15
Tested
0.1
±0.2
±7
±0.5
±0.5
±0.5
1
±0.9
±0.9
±0.5
±0.5
µs
µs
kHz
✻
✻
✻
✻
±0.1
±0.45
±0.45
LSB(1)
LSB
Bits
LSB
%
%
ppm/°C
%
ppm/°C
mV
ppm/°C
mV
ppm/°C
ms
±5
±0.25
±0.25
✻
±10
✻
✻
±3
✻
✻
✻
±0.5
+4.75V < VS < +5.25V
✻
✻
✻
40
Ext. 2.5000V Ref
Ext. 2.5000V Ref
±10V Range
±10V Range
0V to 5V, 0V to 4V Ranges
0V to 5V, 0V to 4V Ranges
2.2µF Capacitor to CAP
pF
✻
LSB
ADS7806
www.ti.com
SBAS021B
ELECTRICAL CHARACTERISTICS (Cont.)
At TA = –40°C to +85°C, fS = 40kHz, VDIG = VANA = +5V, and using internal reference and fixed resistors (see Figure 7b), unless otherwise specified.
ADS7806P, U
PARAMETER
AC ACCURACY
Spurious-Free Dynamic Range
Total Harmonic Distortion
Signal-to-(Noise + Distortion)
Signal-to-Noise
Usable Bandwidth(7)
Full-Power Bandwidth (–3dB)
SAMPLING DYNAMICS
Aperture Delay
Aperture Jitter
Transient Response
Over-Voltage Recovery(8)
REFERENCE
Internal Reference Voltage
Internal Reference Source Current
(Must use external buffer.)
Internal Reference Drift
External Reference Voltage Range
for Specified Linearity
External Reference Current Drain
DIGITAL INPUTS
Logic Levels
VIL
VIH(9)
IIL
IIH
DIGITAL OUTPUTS
Data Format
Data Coding
VOL
VOH
Leakage Current
CONDITIONS
fIN =
fIN =
fIN =
fIN =
1kHz,
1kHz,
1kHz,
1kHz,
±10V
±10V
±10V
±10V
80
90
–90
73
73
130
600
70
70
FS Step
MAX
MIN
✻
–80
72
72
No Load
2.48
2.5
1
8
2.5
External 2.5000V Ref
VIL = 0V
VIH = 5V
Must be ≤ VANA
✻
2.7
✻
✻
✻
✻
✻
Parallel 12-bits in 2-bytes; Serial
Binary Two’s Complement or Straight Binary
+0.8
✻
VD +0.3V
✻
±10
±10
+0.4
VANA = VDIG = 5V, fS = 40kHz
REFD HIGH
PWRD and REFD HIGH
✻
✻
2.52
✻
+5
+5
0.6
5.0
28
23
50
–40
–55
–65
dB(6)
dB
dB
dB
kHz
kHz
ns
ps
µs
ns
V
µA
ppm/°C
V
✻
µA
✻
✻
✻
✻
V
V
µA
µA
✻
±5
✻
V
V
µA
15
✻
pF
83
83
✻
✻
ns
ns
✻
✻
V
V
mA
mA
mW
mW
µW
+5.25
+5.25
✻
✻
35
+85
+125
+150
75
75
UNITS
✻
✻
+4
+4.75
+4.75
MAX
✻
100
–0.3
+2.0
RL = 3.3kΩ, CL = 50pF
RL = 3.3kΩ, CL = 10pF
✻
✻
✻
✻
✻
✻
5
2.3
DIGITAL TIMING
Bus Access Time
Bus Relinquish Time
TYP
✻
✻
750
Output Capacitance
TEMPERATURE RANGE
Specified Performance
Derated Performance
Storage
Thermal Resistance (θJA)
DIP
SO
TYP
40
20
ISINK = 1.6mA
ISOURCE = 500µA
High-Z State,
VOUT = 0V to VDIG
High-Z State
POWER SUPPLIES
Specified Performance
VDIG
VANA
IDIG
IANA
Power Dissipation
MIN
ADS7806PB, UB
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
°C
°C
°C
°C/W
°C/W
✻ Specifications same as ADS7806 P, U.
NOTES: (1) LSB means Least Significant Bit. One LSB for the ±10V input range is 4.88mV. (2) Typical rms noise at worst-case transition. (3) As measured with
fixed resistors, see Figure 7b. Adjustable to zero with external potentiometer. (4) Full-scale error is the worst case of –Full-Scale or +Full-Scale untrimmed deviation
from ideal first and last code transitions, divided by the transition voltage (not divided by the full-scale range) and includes the effect of offset error. (5) This is the
time delay after the ADS7806 is brought out of Power-Down mode until all internal settling occurs and the analog input is acquired to rated accuracy. A Convert
command after this delay will yield accurate results. (6) All specifications in dB are referred to a full-scale input. (7) Usable bandwidth defined as full-scale input
frequency at which Signal-to-(Noise + Distortion) degrades to 60dB. (8) Recovers to specified performance after 2 • FS input overvoltage. (9) The minimum VIH
level for the DATACLK signal is 3V.
ADS7806
SBAS021B
www.ti.com
3
PIN DESCRIPTIONS
DIGITAL
I/O
PIN #
NAME
1
2
3
4
5
6
7
8
9
R1IN
AGND1
R2IN
CAP
REF
AGND2
SB/BTC
EXT/INT
D7
10
11
12
13
14
15
16
17
18
19
20
21
22
D6
D5
D4
D3
DGND
D2
D1
D0
DATACLK
SDATA
TAG
BYTE
R/C
O
O
O
I/O
O
I
I
I
23
CS
I
24
BUSY
O
25
26
27
28
PWRD
REFD
VANA
VDIG
I
I
DESCRIPTION
Analog Input. See Figure 7.
Analog Sense Ground
Analog Input. See Figure 7.
Reference Buffer Output. 2.2µF tantalum capacitor to ground.
Reference Input/Output. 2.2µF tantalum capacitor to ground.
Analog Ground
Selects Straight Binary or Binary Two’s Complement for Output Data Format.
External/Internal data clock select.
Data Bit 3 if BYTE is HIGH. Data bit 11 (MSB) if BYTE is LOW. Hi-Z when CS is HIGH and/or R/C is LOW. Leave
unconnected when using serial output.
Data Bit 2 if BYTE is HIGH. Data bit 10 if BYTE is LOW. Hi-Z when CS is HIGH and/or R/C is LOW.
Data Bit 1 if BYTE is HIGH. Data bit 9 if BYTE is LOW. Hi-Z when CS is HIGH and/or R/C is LOW.
Data Bit 0 (LSB) if BYTE is HIGH. Data bit 8 if BYTE is LOW. Hi-Z when CS is HIGH and/or R/C is LOW.
LOW if BYTE is HIGH. Data bit 7 if BYTE is LOW. Hi-Z when CS is HIGH and/or R/C is LOW.
Digital Ground
LOW if BYTE is HIGH. Data bit 6 if BYTE is LOW. Hi-Z when CS is HIGH and/or R/C is LOW.
LOW if BYTE is HIGH. Data bit 5 if BYTE is LOW. Hi-Z when CS is HIGH and/or R/C is LOW.
LOW if BYTE is HIGH. Data bit 4 if BYTE is LOW. Hi-Z when CS is HIGH and/or R/C is LOW.
Data Clock Output when EXT/INT is LOW. Data clock input when EXT/INT is HIGH.
Serial Output Synchronized to DATACLK
Serial Input When Using an External Data Clock
Selects 8 most significant bits (LOW) or 4 least significant bits (HIGH) on parallel output pins.
With CS LOW and BUSY HIGH, a Falling Edge on R/C Initiates a New Conversion. With CS LOW, a rising edge on R/C
enables the parallel output.
Internally OR’ed with R/C. If R/C is LOW, a falling edge on CS initiates a new conversion. If EXT/INT is LOW, this same
falling edge will start the transmission of serial data results from the previous conversion.
At the start of a conversion, BUSY goes LOW and stays LOW until the conversion is completed and the digital outputs
have been updated.
PWRD HIGH shuts down all analog circuitry except the reference. Digital circuitry remains active.
REFD HIGH shuts down the internal reference. External reference will be required for conversions.
Analog Supply. Nominally +5V. Decouple with 0.1µF ceramic and 10µF tantalum capacitors.
Digital Supply. Nominally +5V. Connect directly to pin 27. Must be ≤ VANA.
I
I
O
O
O
O
O
PIN CONFIGURATION
Top View
DIP, SO
R1IN
1
28 VDIG
AGND1
2
27 VANA
R2IN
3
26 REFD
CAP
4
25 PWRD
REF
5
24 BUSY
AGND2
6
23 CS
SB/BTC
7
ANALOG
INPUT
RANGE
CONNECT R1IN
VIA 200Ω
TO
CONNECT R2IN
VIA 100Ω
TO
IMPEDANCE
±10V
0V to 5V
0V to 4V
VIN
AGND
VIN
CAP
VIN
VIN
45.7kΩ
20.0kΩ
21.4kΩ
TABLE I. Input Range Connections. See Figure 7.
22 R/C
ADS7806
4
EXT/INT
8
21 BYTE
D7
9
20 TAG
D6 10
19 SDATA
D5 11
18 DATACLK
D4 12
17 D0
D3 13
16 D1
DGND 14
15 D2
ADS7806
www.ti.com
SBAS021B
TYPICAL CHARACTERISTICS
TA = +25°C, fS = 40kHz, VDIG = VANA = +5V, and using internal reference and fixed resistors (see Figure 7b), unless otherwise specified.
FREQUENCY SPECTRUM
(8192 Point FFT; fIN = 15kHz, 0dB)
0
0
–20
–20
–40
–40
Amplitude (dB)
–60
–80
–60
–80
–100
–100
–120
–120
0
5
10
15
0
20
5
10
Frequency (kHz)
90
90
80
80
0dB
70
70
60
SINAD (dB)
SINAD (dB)
20
SIGNAL-TO-(NOISE + DISTORTION)
vs INPUT FREQUENCY AND INPUT AMPLITUDE
SIGNAL-TO-(NOISE + DISTORTION)
vs INPUT FREQUENCY (fIN = 0dB)
60
50
40
–20dB
50
40
30
30
20
20
10
–60dB
0
10
100
1k
10k
100k
0
1M
2
4
6
8
10
12
14
16
Input Signal Frequency (Hz)
Input Signal Frequency (kHz)
SIGNAL-TO-(NOISE + DISTORTION) vs TEMPERATURE
(fIN = 1kHz, 0dB; fS = 10kHz to 40kHz)
AC PARAMETERS vs TEMPERATURE
(fIN = 1kHz, 0dB)
74.0
110
73.9
10kHz
73.8
40kHz
73.7
73.6
–75
SFDR, SNR, and SINAD (dB)
20kHz
20
–60
–65
100
–70
95
–75
90
–80
85
–85
80
–90
SNR and SINAD
75
–95
70
–100
THD
65
–105
60
–50
–25
0
25
50
75
Temperature (°C)
100
125
150
–110
–75
–50
–25
0
25
50
75
100
125
150
Temperature (°C)
ADS7806
SBAS021B
18
SFDR
105
30kHz
SINAD (dB)
15
Frequency (kHz)
THD (dB)
Amplitude (dB)
FREQUENCY SPECTRUM
(8192 Point FFT; fIN = 1kHz, 0dB)
www.ti.com
5
TYPICAL CHARACTERISTICS (Cont.)
TA = +25°C, fS = 40kHz, VDIG = VANA = +5V, and using internal reference and fixed resistors (see Figure 7b), unless otherwise specified.
POWER-SUPPLY RIPPLE SENSITIVITY
INL/DNL DEGRADATION PER LSB OF P-P RIPPLE
1
Linearity Degradation (LSB/LSB)
12-Bit (LSBs)
0.10
0
All Codes INL
–0.10
12-Bit (LSBs)
0.10
0
–0.10
All Codes DNL
0
512
10–1
10–2
INL
10–3
10–4
DNL
10–5
1024
1536
2048
2560
3072
3584
4095
101
102
mV From Ideal
Percent
From Ideal
BPZ Error
0
+FS Error
–FS Error
0
–0.20
–75
–50
–25
0
25
50
75
100
125
3
2
1
0
–1
–2
0.40
107
0.20
0
0.40
+FS Error (4V Range)
–FS Error (5V Range)
0.20
0
150
–75
–50
–25
0
25
50
75
100
125
150
125
150
Temperature (°C)
INTERNAL REFERENCE VOLTAGE vs TEMPERATURE
CONVERSION TIME vs TEMPERATURE
2.520
15.10
2.515
15.00
2.510
Conversion Time (µs)
Internal Reference (V)
106
UPO Error
Temperature (°C)
2.505
2.500
2.495
2.490
2.485
14.90
14.80
14.70
14.60
14.50
14.40
14.30
14.20
2.480
–75
–50
–25
0
25
50
75
100
125
150
–75
–50
–25
0
25
50
75
100
Temperature (°C)
Temperature (°C)
6
105
ENDPOINT ERRORS (Unipolar Ranges)
Percent
From Ideal
Percent
From Ideal
Percent
From Ideal
mV From Ideal
ENDPOINT ERRORS (20V Bipolar Range)
–0.20
0.20
104
Power-Supply Ripple Frequency (Hz)
Decimal Code
3
2
1
0
–1
–2
0.20
103
ADS7806
www.ti.com
SBAS021B
BASIC OPERATION
PARALLEL OUTPUT
Figure 1a shows a basic circuit to operate the ADS7806 with
a ±10V input range and parallel output. Taking R/C (pin 22)
LOW for 40ns (12µs max) will initiate a conversion. BUSY
(pin 24) will go LOW and stay LOW until the conversion is
completed and the output register is updated. If BYTE (pin
21) is LOW, the eight Most Significant Bits (MSBs) will be
valid when BUSY rises; if BYTE is HIGH, the four Least
Significant Bits (LSBs) will be valid when BUSY rises. Data
will be output in Binary Two’s Complement (BTC) format.
BUSY going HIGH can be used to latch the data. After the
first byte has been read, BYTE can be toggled allowing the
remaining byte to be read. All convert commands will be
ignored while BUSY is LOW.
The ADS7806 will begin tracking the input signal at the end
of the conversion. Allowing 25µs between convert commands assures accurate acquisition of a new signal.
The offset and gain are adjusted internally to allow external
trimming with a single supply. The external resistors compensate for this adjustment and can be left out if the offset and
gain will be corrected in software (refer to the Calibration
section).
SERIAL OUTPUT
Figure 1b shows a basic circuit to operate the ADS7806 with
a ±10V input range and serial output. Taking R/C (pin 22)
LOW for 40ns (12µs max) will initiate a conversion and
output valid data from the previous conversion on SDATA
(pin 19) synchronized to 12 clock pulses output on DATACLK
(pin 18). BUSY (pin 24) will go LOW and stay LOW until the
conversion is completed and the serial data has been transmitted. Data will be output in BTC format, MSB first, and will
be valid on both the rising and falling edges of the data clock.
BUSY going HIGH can be used to latch the data. All convert
commands will be ignored while BUSY is LOW.
The ADS7806 will begin tracking the input signal at the end
of the conversion. Allowing 25µs between convert commands assures accurate acquisition of a new signal.
The offset and gain are adjusted internally to allow external
trimming with a single supply. The external resistors compensate for this adjustment and can be left out if the offset and
gain will be corrected in software (refer to the Calibration
section).
STARTING A CONVERSION
The combination of CS (pin 23) and R/C (pin 22) LOW for a
minimum of 40ns immediately puts the sample-and-hold of
the ADS7806 in the hold state and starts conversion ‘n’.
BUSY (pin 24) will go LOW and stay LOW until conversion
‘n’ is completed and the internal output register has been
updated. All new convert commands during BUSY LOW will
be ignored. CS and/or R/C must go HIGH before BUSY goes
HIGH, or a new conversion will be initiated without sufficient
time to acquire a new signal.
Serial Output
Parallel Output
200Ω
±10V
1
66.5kΩ
2
27
3
26
2.2µF
+5V
0.1µF 10µF
+
+
±10V
4
2.2µF
+ 5
25
6
23
66.5kΩ
100Ω
BUSY
24
Convert Pulse
2.2µF
R/C
7
Pin 21 B11 B10
LOW (MSB)
B9
Pin 21
HIGH
B1
B3
B2
B8
B7
B0 LOW
(LSB)
2.2µF
+
BYTE
21
9
20
10
19
11
18
12
17
28
2
27
3
26
4
25
5
24
6
23
7
40ns min
0.1µF 10µF
+
+
22
NC(1)
8
21
9
20
NC(1) 10
19
NC(1)
13
16
NC(1)
14
15
NC(1) 12
17 NC(1)
NC(1) 13
16 NC(1)
14
15 NC(1)
B6
B5
+5V
BUSY
Convert Pulse
R/C
ADS7806
B4
11
18
40ns min
SDATA
DATACLK
LOW LOW LOW
NOTE: (1) These pins should be left unconnected.
They will be active when R/C is HIGH.
NOTE: (1) SDATA (pin 19) is always active.
FIGURE 1a. Basic ±10V Operation, both Parallel and Serial
Output.
FIGURE 1b. Basic ±10V Operation with Serial Output.
ADS7806
SBAS021B
+
22
ADS7806
8
1
+5V
+5V
100Ω
+
200Ω
28
www.ti.com
7
The ADS7806 will begin tracking the input signal at the end
of the conversion. Allowing 25µs between convert commands assures accurate acquisition of a new signal. Refer to
Tables II and III for a summary of CS , R/C, and BUSY states,
and Figures 2 through 6 for timing diagrams.
CS
R/C
BUSY
1
X
X
OPERATION
None. Databus is in Hi-Z state.
↓
0
1
Initiates conversion ‘n’. Databus remains
in Hi-Z state.
0
↓
1
Initiates conversion ‘n’. Databus enters Hi-Z
state.
0
1
↑
Conversion ‘n’ completed. Valid data from
conversion ‘n’ on the databus.
↓
1
1
Enables databus with valid data from
conversion ‘n’.
↓
1
0
Enables databus with valid data from
conversion ‘n – 1’(1). Conversion ‘n’ in progress.
0
↑
0
Enables databus with valid data from
conversion ‘n – 1’(1). Conversion ‘n’ in progress.
CS and R/C are internally OR’ed and level triggered. There is
no requirement which input goes LOW first when initiating a
conversion. If, however, it is critical that CS or R/C initiates
conversion ‘n’, be sure the less critical input is LOW at least 10ns
prior to the initiating input. If EXT/INT (pin 8) is LOW when
initiating conversion ‘n’, serial data from conversion ‘n – 1’ will be
output on SDATA (pin 19) following the start of conversion ‘n’.
See Internal Data Clock in the Reading Data section.
To reduce the number of control pins, CS can be tied LOW
using R/C to control the read and convert modes. This will
have no effect when using the internal data clock in the serial
output mode. The parallel output and the serial output (only
when using an external data clock), however, will be affected
whenever R/C goes HIGH. Refer to the Reading Data
section.
0
0
↑
New conversion initiated without acquisition
of a new signal. Data will be invalid. CS and/or
R/C must be HIGH when BUSY goes HIGH.
X
X
0
New convert commands ignored. Conversion
‘n’ in progress.
NOTE: (1) See Figures 2 and 3 for constraints on data valid from
conversion ‘n – 1’.
TABLE II. Control Functions When Using Parallel Output
(DATACLK tied LOW, EXT/INT tied HIGH).
READING DATA
The ADS7806 outputs serial or parallel data in Straight
Binary (SB) or Binary Two’s Complement data output format.
If SB/BTC (pin 7) is HIGH, the output will be in SB format,
and if LOW, the output will be in BTC format. Refer to Table
IV for ideal output codes.
The parallel output can be read without affecting the internal
output registers; however, reading the data through the serial
port will shift the internal output registers one bit per data
clock pulse. As a result, data can be read on the parallel port
CS
R/C
BUSY
EXT/INT
DATACLK
↓
0
1
0
Output
OPERATION
Initiates conversion ‘n’. Valid data from conversion ‘n – 1’ clocked out on SDATA.
0
↓
1
0
Output
Initiates conversion ‘n’. Valid data from conversion ‘n – 1’ clocked out on SDATA.
↓
0
1
1
Input
Initiates conversion ‘n’. Internal clock still runs conversion process.
0
↓
1
1
Input
Initiates conversion “n”. Internal clock still runs conversion process.
↓
1
1
1
Input
Conversion ‘n’ completed. Valid data from conversion ‘n’ clocked out on SDATA synchronized
to external data clock.
↓
1
0
1
Input
Valid data from conversion ‘n – 1’ output on SDATA synchronized to external data clock.
Conversion ‘n’ in progress.
0
↑
0
1
Input
Valid data from conversion ‘n – 1’ output on SDATA synchronized to external data clock.
Conversion ‘n’ in progress.
0
0
↑
X
X
New conversion initiated without acquisition of a new signal. Data will be invalid. CS and/or R/C
must be HIGH when BUSY goes HIGH.
X
X
0
X
X
New convert commands ignored. Conversion “n” in progress.
NOTE: (1) See Figures 4, 5, and 6 for constraints on data valid from conversion ‘n – 1’.
TABLE III. Control Functions When Using Serial Output.
DESCRIPTION
Full-Scale Range
Least Significant Bit (LSB)
ANALOG INPUT
±10
4.88mV
0V to 5V
1.22mV
0V to 4V
976µV
DIGITAL OUTPUT
BINARY TWO’S COMPLEMENT
STRAIGHT BINARY
(SB/BTC LOW)
(SB/BTC HIGH)
HEX
+Full-Scale (FS – 1LSB)
Midscale
One LSB Below Midscale
–Full-Scale
HEX
BINARY CODE
CODE
BINARY CODE
9.99512V
4.99878V
3.999024V
0111 1111 1111 1111
7FF
1111 1111 1111 1111
CODE
FFF
0V
2.5V
2V
0000 0000 0000 0000
000
1000 0000 0000 0000
800
–4.88mV
2.49878V
1.999024V
1111 1111 1111 1111
FFF
0111 1111 1111 1111
7FF
–10V
0V
0V
1000 0000 0000 0000
800
0000 0000 0000 0000
000
TABLE IV. Output Codes and Ideal Input Voltages.
8
ADS7806
www.ti.com
SBAS021B
prior to reading the same data on the serial port, but data
cannot be read through the serial port prior to reading the
same data on the parallel port.
PARALLEL OUTPUT
To use the parallel output, tie EXT/INT (pin 8) HIGH and
DATACLK (pin 18) LOW. SDATA (pin 19) should be left
unconnected. The parallel output will be active when R/C
(pin 22) is HIGH and CS (pin 23) is LOW. Any other
combination of CS and R/C will tri-state the parallel output.
Valid conversion data can be read in two 8-bit bytes on D7D0 (pins 9-13 and 15-17). When BYTE (pin 21) is LOW, the
eight most significant bits will be valid with the MSB on D7.
When BYTE is HIGH, the four least significant bits will be
valid with the LSB on D4. BYTE can be toggled to read both
bytes within one conversion cycle.
PARALLEL OUTPUT (AFTER A CONVERSION)
After conversion ‘n’ is completed and the output registers
have been updated, BUSY (pin 24) will go HIGH. Valid data
from conversion ‘n’ will be available on D7-D0 (pins 9-13 and
15-17). BUSY going high can be used to latch the data. Refer
to Table V and Figures 2 and 3 for timing constraints.
PARALLEL OUTPUT (DURING A CONVERSION)
After conversion ‘n’ has been initiated, valid data from conversion ‘n – 1’ can be read and will be valid up to 12µs after the
start of conversion ‘n’. Do not attempt to read data beyond
12µs after the start of conversion ‘n’ until BUSY (pin 24) goes
HIGH; this may result in reading invalid data. Refer to Table V
and Figures 2 and 3 for timing constraints.
Upon initial power up, the parallel output will contain indeterminate data.
t1
t1
R/C
t3
t3
t4
BUSY
t5
t6
t6
t7
Convert
Acquire
MODE
t8
Acquire
t12
t11
Parallel
Data Bus
Previous
High Byte Valid
Previous High
Byte Valid
Hi-Z
Convert
t12
t10
Previous Low
Byte Valid
Not Valid
Low Byte
Valid
High Byte
Valid
Hi-Z
t9
t2
t12
t12
t9
High Byte
Valid
t12
t12
BYTE
FIGURE 2. Conversion Timing with Parallel Output (CS and DATACLK tied LOW, EXT/INT tied HIGH).
t21
t21
t21
t21
t21
t21
t21
t21
t21
t21
R/C
t1
CS
t3
BUSY
t4
BYTE
DATA
BUS
Hi-Z State
High Byte
t12
Hi-Z State
t9
Low Byte
t12
Hi-Z State
t9
FIGURE 3. Using CS to Control Conversion and Read Timing with Parallel Outputs.
ADS7806
SBAS021B
www.ti.com
9
SYMBOL
DESCRIPTION
t1
Convert Pulse Width
t2
Data Valid Delay after R/C LOW
t3
BUSY Delay from
INTERNAL DATA CLOCK
MIN TYP MAX UNITS
0.04
14.7
12
µs
20
µs
85
ns
20
µs
(During A Conversion)
To use the internal data clock, tie EXT/INT (pin 8) LOW. The
combination of R/C (pin 22) and CS (pin 23) LOW will initiate
conversion ‘n’ and activate the internal data clock (typically a
900kHz clock rate). The ADS7806 will output 12 bits of valid
data, MSB first, from conversion ‘n – 1’ on SDATA (pin 19),
synchronized to 12 clock pulses output on DATACLK (pin
18). The data will be valid on both the rising and falling edges
of the internal data clock. The rising edge of BUSY (pin 24)
can be used to latch the data. After the 12th clock pulse,
DATACLK will remain LOW until the next conversion is
initiated, while SDATA will go to whatever logic level was
input on TAG (pin 20) during the first clock pulse. Refer to
Table VI and Figure 4.
Start of Conversion
t4
BUSY LOW
14.7
t5
BUSY Delay after
90
ns
End of Conversion
t6
Aperture Delay
40
t7
Conversion Time
14.7
ns
20
µs
5
µs
83
ns
t8
Acquisition Time
t9
Bus Relinquish Time
10
t10
BUSY Delay after Data Valid
20
60
ns
t11
Previous Data Valid
12
14.7
µs
t12
Bus Access Time and BUSY Delay
t13
Start of Conversion
after Start of Conversion
83
ns
1.4
µs
to DATACLK Delay
t14
DATACLK Period
t15
Data Valid to DATACLK
1.1
µs
EXTERNAL DATA CLOCK
20
75
ns
400
600
ns
To use an external data clock, tie EXT/INT (pin 8) HIGH. The
external data clock is not a conversion clock; it can only be
used as a data clock. To enable the output mode of the
ADS7806, CS (pin 23) must be LOW and R/C (pin 22) must
be HIGH. DATACLK must be HIGH for 20% to 70% of the
total data clock period; the clock rate can be between DC and
10MHz. Serial data from conversion ‘n’ can be output on
SDATA (pin 19) after conversion ‘n’ is completed or during
conversion ‘n + 1’.
HIGH Delay
t16
Data Valid after DATACLK
LOW Delay
t17
External DATACLK Period
100
ns
t18
External DATACLK LOW
40
ns
t19
External DATACLK HIGH
50
ns
t20
CS and R/C to External
25
ns
ns
DATACLK Setup Time
t21
R/C to CS Setup Time
10
t22
Valid Data after DATACLK HIGH
25
t7 + t8
Throughput Time
ns
25
An obvious way to simplify control of the converter is to tie
CS LOW and use R/C to initiate conversions. While this is
perfectly acceptable, there is a possible problem when using
an external data clock. At an indeterminate point from 12µs
after the start of conversion ‘n’ until BUSY rises, the internal
logic will shift the results of conversion ‘n’ into the output
register. If CS is LOW, R/C is HIGH, and the external clock
is HIGH at this point, data will be lost. So, with CS LOW,
either R/C and/or DATACLK must be LOW during this period
to avoid losing valid data.
µs
TABLE V. Conversion and Data Timing. TA = –40°C to +85°C.
SERIAL OUTPUT
Data can be clocked out with the internal data clock or an
external data clock. When using serial output, be careful with
the parallel outputs, D7-D0 (pins 9-13 and 15-17), as these
pins will come out of Hi-Z state whenever CS (pin 23) is LOW
and R/C (pin 22) is HIGH. The serial output can not be tristated and is always active.
t 7 + t8
CS or R/C(1)
t14
DATACLK
t13
1
2
3
11
12
1
2
Bit 9 Valid
Bit 1 Valid
LSB Valid
MSB Valid
Bit 10 Valid
t16
t15
MSB Valid
Bit 10 Valid
SDATA
(Results from previous conversion.)
BUSY
NOTE: (1) If controlling with CS , tie R/C LOW. Data bus pins will remain Hi-Z at all times.
If controlling with R/C, tie CS LOW. Data bus pins will be active when R/C is HIGH, and should be left unconnected.
FIGURE 4. Serial Data Timing Using Internal Data Clock (TAG tied LOW).
10
ADS7806
www.ti.com
SBAS021B
FIGURE 5. Conversion and Read Timing with External Clock (EXT/INT Tied HIGH) Read after Conversion.
ADS7806
SBAS021B
www.ti.com
11
TAG
SDATA
BUSY
R/C
CS
EXTERNAL
DATACLK
t21
t3
t1
0
t18
t17
Tag 0
t19
t21
1
t22
Tag 1
Bit 11 (MSB)
t20
2
Tag 2
Bit 10
3
11
Tag 11
Bit 1
12
Tag 12
Bit 0 (LSB)
13
Tag 13
Tag 0
14
Tag 14
Tag 1
t20
EXTERNAL DATA CLOCK
TAG FEATURE
(After a Conversion)
TAG (pin 20) inputs serial data synchronized to the external
or internal data clock.
After conversion ‘n’ is completed and the output registers
have been updated, BUSY (pin 24) will go HIGH. With CS
LOW and R/C HIGH, valid data from conversion ‘n’ will be
output on SDATA (pin 19) synchronized to the external data
clock input on DATACLK (pin 18). The MSB will be valid on
the first falling edge and the second rising edge of the
external data clock. The LSB will be valid on the 12th falling
edge and 13th rising edge of the data clock. TAG (pin 20) will
input a bit of data for every external clock pulse. The first bit
input on TAG will be valid on SDATA on the 13th falling edge
and the 14th rising edge of DATACLK; the second input bit
will be valid on the 14th falling edge and the 15th rising edge,
etc. With a continuous data clock, TAG data will be output on
SDATA until the internal output registers are updated with
the results from the next conversion. Refer to Table V and
Figure 5.
EXTERNAL DATA CLOCK
(During a Conversion)
After conversion ‘n’ has been initiated, valid data from conversion ‘n – 1’ can be read and will be valid up to 12µs after
the start of conversion ‘n’. Do not attempt to clock out data
from 12µs after the start of conversion ‘n’ until BUSY (pin 24)
rises; this will result in data loss. NOTE: For the best possible
performance when using an external data clock, data should
not be clocked out during a conversion. The switching noise
of the asynchronous data clock can cause digital feedthrough
degrading the converter’s performance. Refer to Table VI
and Figure 6.
When using an external data clock, the serial bit stream input
on TAG will follow the LSB output on SDATA until the internal
output register is updated with new conversion results. See
Table VI and Figures 5 and 6.
The logic level input on TAG for the first rising edge of the
internal data clock will be valid on SDATA after all 12 bits of
valid data have been output.
INPUT RANGES
The ADS7806 offers three input ranges: standard ±10V, 0V-5V,
and a 0V-4V range for complete, single-supply systems. See
Figures 7a and 7b for the necessary circuit connections for
implementing each input range and optional offset and gain
adjust circuitry. Offset and full-scale error(1) specifications are
tested with the fixed resistors, see Figure 7b. Adjustments for
offset and gain are described in the Calibration section of this
data sheet.
The offset and gain are adjusted internally to allow external
trimming with a single supply. The external resistors compensate for this adjustment and can be left out if the offset and
gain will be corrected in software (refer to the Calibration
section).
The input impedance, summarized in Table II, results from
the combination of the internal resistor network (see the front
page of this data sheet) and the external resistors used for
NOTE: (1) Full-scale error includes offset and gain errors measured at both
+FS and –FS.
t17
t18
t19
EXTERNAL
DATACLK
t20
t22
CS
t21
t20
R/C
t1
t11
BUSY
t3
DATA
TAG
Tag 0
Bit 11 (MSB)
Bit 0 (LSB)
Tag 0
Tag 1
Tag 1
Tag 12
Tag 13
Tag 14
FIGURE 6. Conversion and Read Timing with External Clock (EXT/INT tied HIGH) Read During a Conversion.
12
ADS7806
www.ti.com
SBAS021B
each input range (see Figure 8). The input resistor divider
network provides inherent over-voltage protection to at least
±12V on R1IN and ±5.5V on R2IN.
Analog inputs above or below the expected range will yield
either positive full-scale or negative full-scale digital outputs,
respectively. There will be no wrapping or folding over for
analog inputs outside the nominal range.
GAIN ADJUST
RANGE (mV)
±10V
±15
±60
0 to 5V
±4
±30
0 to 4V
±3
±30
TABLE VI. Offset and Gain Adjust Ranges for Hardware
Calibration (see Figure 7a).
CALIBRATION
are necessary. See the No Calibration section for more
details on the external resistors. Refer to Table VII for the
range of offset and gain errors with and without the external
resistors.
HARDWARE CALIBRATION
To calibrate the offset and gain of the ADS7806 in hardware,
install the resistors shown in Figure 7a. Table VI lists the
hardware trim ranges relative to the input for each input range.
NO CALIBRATION
Figure 7b shows circuit connections. Note that the actual
voltage dropped across the external resistors is at least two
orders of magnitude lower than the voltage dropped across
the internal resistor divider network. This should be consid-
SOFTWARE CALIBRATION
To calibrate the offset and gain in software, no external
resistors are required. However, to get the data sheet specifications for offset and gain, the resistors shown in Figure 7b
±10V
OFFSET ADJUST
RANGE (mV)
INPUT RANGE
0V-5V
0V-4V
33.2kΩ
200Ω
200Ω
1
VIN
2
R1IN
1
2
AGND1
100Ω
3
R1IN
200Ω
1
33.2kΩ
3
VIN
R2IN
100Ω
2
VIN
R2IN
100Ω
3
+5V
4
33.2kΩ
2.2µF
+5V
+
1MΩ
50kΩ
2.2µF
+
50kΩ
50kΩ
6
+
2.2µF
50kΩ
REF
+
1MΩ 2.2µF
AGND2
AGND1
R2IN
+5V
CAP
4
5
REF
+
6
+5V
CAP
2.2µF
5
50kΩ
4
R1IN
AGND1
1MΩ
5
50kΩ
REF
+
2.2µF
AGND2
CAP
6
AGND2
FIGURE 7a. Circuit Diagrams (With Hardware Trim).
±10V
0V-5V
0V-4V
33.2kΩ
200Ω
200Ω
1
VIN
2
R1IN
1
2
AGND1
100Ω
66.5kΩ
3
+5V
R2IN
R1IN
200Ω
1
33.2kΩ
3
VIN
2
VIN
R2IN
100Ω
3
100Ω
4
2.2µF
+
CAP
2.2µF
5
2.2µF
4
5
REF
+
6
+
2.2µF
CAP
4
2.2µF
+
REF
5
+
AGND2
6
R1IN
AGND1
AGND2
2.2µF
AGND1
R2IN
CAP
REF
+
6
AGND2
FIGURE 7b. Circuit Diagrams (Without Hardware Trim).
ADS7806
SBAS021B
www.ti.com
13
ered when choosing the accuracy and drift specifications of
the external resistors. In most applications, 1% metal-film
resistors will be sufficient.
The external resistors, see Figure 7b, may not be necessary
in some applications. These resistors provide compensation
for an internal adjustment of the offset and gain which allows
calibration with a single supply. Not using the external resistors will result in offset and gain errors in addition to those
listed in the electrical characteristics section. Offset refers to
the equivalent voltage of the digital output when converting
with the input grounded. A positive gain error occurs when the
equivalent output voltage of the digital output is larger than the
analog input. Refer to Table VII for nominal ranges of gain and
offset errors with and without the external resistors. Refer to
Figure 8 for typical shifts in the transfer functions which occur
when the external resistors are removed.
To further analyze the effects of removing any combination of
the external resistors, consider Figure 9. The combination of
the external and the internal resistors form a voltage divider
which reduces the input signal to a 0.3125V to 2.8125V input
range at the Capacitor Digital-to-Analog Converter (CDAC).
The internal resistors are laser trimmed to high relative accuracy to meet full specifications. The actual input impedance of
the internal resistor network looking into pin 1 or pin 3,
however, is only accurate to ±20% due to process variations.
This should be taken into account when determining the
effects of removing the external resistors.
REFERENCE
The ADS7806 can operate with its internal 2.5V reference or
an external reference. By applying an external reference to
pin 5, the internal reference can be bypassed; REFD (pin 26)
OFFSET ERROR
WITH RESISTORS
INPUT
RANGE (V)
GAIN ERROR
WITHOUT RESISTORS
WITH RESISTORS
WITHOUT RESISTORS
RANGE (mV)
RANGE (mV)
TYP (mV)
RANGE (% FS)
RANGE (% FS)
TYP
–10 ≤ BPZ ≤ 10
0 ≤ BPZ ≤ 35
+15
–0.4 ≤ G ≤ 0.4
0.15 ≤ G(1) ≤ 0.15
–0.3 ≤ G ≤ 0.5
–0.1 ≤ G(1) ≤ 0.2
+0.05
+0.05
0 to 5
–3 ≤ UPO ≤ 3
–12 ≤ UPO ≤ –3
–7.5
–0.4 ≤ G ≤ 0.4
0.15 ≤ G(1) ≤ 0.15
–1.0 ≤ G ≤ 0.1
–0.55 ≤ G(1) ≤ –0.05
–0.2
–0.2
0 to 4
–3 ≤ UPO ≤ 3
–10.5 ≤ UPO ≤ –1.5
–6
–0.4 ≤ G ≤ 0.4
–0.15 ≤ G(1) ≤ 0.15
–1.0 ≤ G ≤ 0.1
–0.55 ≤ G(1) ≤ –0.05
–0.2
–0.2
±10
NOTE: (1) High Grade.
TABLE VII. Range of Offset and Gain Errors With and Without External Resistors
(a) Bipolar
(b) Unipolar
Digital Output
Digital Output
+Full-Scale
+Full-Scale
Analog Input
–Full-Scale
Analog Input
–Full-Scale
Typical Transfer Functions
With External Resistors
Typical Transfer Functions
Without External Resistors
FIGURE 8. Typical Transfer Functions With and Without External Resistors.
14
ADS7806
www.ti.com
SBAS021B
200Ω
39.8kΩ
VIN
CDAC (High Impedance)
(0.3125V to 2.8125V)
66.5kΩ
40kΩ
20kΩ
9.9kΩ
+5V
100Ω
+2.5V
+2.5V
200Ω
39.8kΩ
CDAC (High Impedance)
(0.3125V to 2.8125V)
33.2kΩ
100Ω
20kΩ
9.9kΩ
40kΩ
VIN
+2.5V
200Ω
+2.5V
39.8kΩ
VIN
CDAC (High Impedance)
(0.3125V to 2.8125V)
33.2kΩ
100Ω
40kΩ
20kΩ
9.9kΩ
+2.5V
+2.5V
FIGURE 9. Circuit Diagrams Showing External and Internal Resistors.
tied HIGH will power-down the internal reference reducing
the overall power consumption of the ADS7806 by approximately 5mW.
ZCAP
The internal reference has approximately an 8 ppm/°C drift
(typical) and accounts for approximately 20% of the full-scale
error (FSE = ±0.5% for low grade, ±0.25% for high grade).
CAP
(Pin 4)
The ADS7806 also has an internal buffer for the reference
voltage. Figure 10 shows characteristic impedances at the
input and output of the buffer with all combinations of powerdown and reference down.
CDAC
Buffer
Internal
Reference
REF
(Pin 5)
ZREF
REF
REF (pin 5) is an input for an external reference or the output
for the internal 2.5V reference. A 2.2µF tantalum capacitor
should be connected as close as possible to the REF pin
from ground. This capacitor and the output resistance of REF
create a low-pass filter to bandlimit noise on the reference.
Using a smaller value capacitor will introduce more noise to
the reference, degrading the SNR and SINAD. The REF pin
should not be used to drive external AC or DC loads, as
shown in Figure 10.
The range for the external reference is 2.3V to 2.7V and
determines the actual LSB size. Increasing the reference
voltage will increase the full-scale range and the LSB size of
the converter which can improve the SNR.
PWRD 0
REFD 1
PWRD 1
REFD 0
PWRD 1
REFD 1
ZCAP (Ω)
1
1
200
200
ZREF (Ω)
6k
100M
6k
100M
FIGURE 10. Characteristic Impedances of Internal Buffer.
CAP
CAP (pin 4) is the output of the internal reference buffer. A
2.2µF tantalum capacitor should be placed as close as
possible to the CAP pin from ground to provide optimum
switching currents for the CDAC throughout the conversion
ADS7806
SBAS021B
PWRD 0
REFD 0
www.ti.com
15
cycle. This capacitor also provides compensation for the
output of the buffer. Using a capacitor any smaller than 1µF
can cause the output buffer to oscillate and may not have
sufficient charge for the CDAC. Capacitor values larger than
2.2µF will have little affect on improving performance. See
Figures 10 and 11.
7000
6000
5000
REFD HIGH will power-down the internal 2.5V reference. All
other analog circuitry, including the reference buffer, will be
active. REFD should be HIGH when using an external
reference to minimize power consumption and the loading
effects on the external reference. See Figure 10 for the
characteristic impedance of the reference buffer’s input for
both REFD HIGH and LOW. The internal reference consumes approximately 5mW.
LAYOUT
4000
µs
POWER
3000
For optimum performance, tie the analog and digital power
pins to the same +5V power supply and tie the analog and
digital grounds together. As noted in the electrical characteristics, the ADS7806 uses 90% of its power for the analog
circuitry. The ADS7806 should be considered as an analog
component.
2000
1000
0
0.1
1
10
100
“CAP” Pin Value (µF)
FIGURE 11. Power-Down to Power-Up Time vs Capacitor
Value on CAP.
The output of the buffer is capable of driving up to 1mA of
current to a DC load. Using an external buffer will allow the
internal reference to be used for larger DC loads and AC
loads. Do not attempt to directly drive an AC load with the
output voltage on CAP. This will cause performance degradation of the converter.
REFERENCE AND
POWER-DOWN
The +5V power for the A/D converter should be separate
from the +5V used for the system’s digital logic. Connecting
VDIG (pin 28) directly to a digital supply can reduce converter
performance due to switching noise from the digital logic. For
best performance, the +5V supply can be produced from
whatever analog supply is used for the rest of the analog
signal conditioning. If +12V or +15V supplies are present, a
simple +5V regulator can be used. Although it is not suggested, if the digital supply must be used to power the
converter, be sure to properly filter the supply. When using
either a filtered digital supply or a regulated analog supply,
both VDIG and VANA should be tied to the same +5V source.
GROUNDING
The ADS7806 has analog power-down and reference power
down capabilities via PWRD (pin 25) and REFD (pin 26),
respectively. PWRD and REFD HIGH will power-down all
analog circuitry maintaining data from the previous conversion in the internal registers, provided that the data has not
already been shifted out through the serial port. Typical
power consumption in this mode is 50µW. Power recovery is
typically 1ms, using a 2.2µF capacitor connected to CAP.
Figure 11 shows power-down to power-up recovery time
relative to the capacitor value on CAP. With +5V applied to
VDIG, the digital circuitry of the ADS7806 remains active at all
times, regardless of PWRD and REFD states.
PWRD
PWRD HIGH will power-down all of the analog circuitry
except for the reference. Data from the previous conversion
will be maintained in the internal registers and can still be
read. With PWRD HIGH, a convert command yields meaningless data.
16
REFD
Three ground pins are present on the ADS7806. DGND is the
digital supply ground. AGND2 is the analog supply ground.
AGND1 is the ground to which all analog signals internal to the
A/D converter are referenced. AGND1 is more susceptible to
current induced voltage drops and must have the path of
least resistance back to the power supply.
All the ground pins of the A/D converter should be tied to an
analog ground plane, separated from the system’s digital
logic ground, to achieve optimum performance. Both analog
and digital ground planes should be tied to the “system”
ground as near to the power supplies as possible. This helps
to prevent dynamic digital ground currents from modulating
the analog ground through a common impedance to power
ground.
SIGNAL CONDITIONING
The FET switches used for the sample hold on many CMOS
A/D converters release a significant amount of charge injection which can cause the driving op amp to oscillate. The
amount of charge injection due to the sampling FET switch
ADS7806
www.ti.com
SBAS021B
on the ADS7806 is approximately 5% to 10% of the amount
on similar A/D converters with the charge redistribution
Digital-to-Analog Converter (DAC) CDAC architecture. There
is also a resistive front end which attenuates any charge
which is released. The end result is a minimal requirement for
the drive capability on the signal conditioning preceding the
A/D converter. Any op amp sufficient for the signal in an
application will be sufficient to drive the ADS7806.
The resistive front end of the ADS7806 also provides a
specified ±25V over-voltage protection. In most cases, this
eliminates the need for external over-voltage protection circuitry.
INTERMEDIATE LATCHES
The ADS7806 does have tri-state outputs for the parallel
port, but intermediate latches should be used if the bus will
be active during conversions. If the bus is not active during
conversion, the tri-state outputs can be used to isolate the
A/D converter from other peripherals on the same bus.
Before enabling the QSPI interface, the microcontroller must
be configured to monitor the slave-select line. When a
transition from LOW to HIGH occurs on Slave Select (SS)
from BUSY (indicating the end of the current conversion), the
port can be enabled. If this is not done, the microcontroller
and the A/D converter may be “out-of-sync.”
Figure 13 shows another interface between the ADS7806
and a QSPI equipped microcontroller. The interface allows
the microcontroller to give the convert pulses while also
allowing multiple peripherals to be connected to the serial
bus. This interface and the following discussion assume a
master clock for the QSPI interface of 16.78MHz. Notice that
the serial data input of the microcontroller is tied to the MSB
(D7) of the ADS7806 instead of the serial output (SDATA).
Using D7 instead of the serial port offers tri-state capability
which allows other peripherals to be connected to the MISO
pin. When communication is desired with those peripherals,
PCS0 and PCS1 should be left HIGH; that will keep D7 tristated and prevent a conversion from taking place.
Intermediate latches are beneficial on any monolithic A/D
converter. The ADS7806 has an internal LSB size of 610µV.
Transients from fast switching signals on the parallel port,
even when the A/D converter is tri-stated, can be coupled
through the substrate to the analog circuitry causing degradation of converter performance. The effects of this phenomenon will be more obvious when using the pin-compatible
ADS7807 or any of the other 16-bit converters in the ADS
Family. This is due to the smaller internal LSB size of 38µV.
QSPI™
APPLICATIONS INFORMATION
Figure 12 shows a simple interface between the ADS7806
and any QSPI equipped microcontroller. This interface assumes that the convert pulse does not originate from the
microcontroller and that the ADS7806 is the only serial
peripheral.
Convert Pulse
QSPI™
ADS7806
R/C
PCS0/SS
MOSI
SCK
BUSY
SDATA
DATACLK
CS
EXT/INT
CPOL = 0 (Inactive State is LOW)
CPHA = 1 (Data valid on falling edge)
QSPI port is in slave mode.
BYTE
FIGURE 12. QSPI Interface to the ADS7806.
R/C
PCS1
CS
+5V
EXT/INT
SCK
DATACLK
MISO
D7 (MSB)
BYTE
FIGURE 13. QSPI Interface to the ADS7806. Processor
Initiates Conversions.
In this configuration, the QSPI interface is actually set to do
two different serial transfers. The first, an 8-bit transfer,
causes PCS0 (R/C) and PCS1 (CS ) to go LOW, starting a
conversion. The second, a 12-bit transfer, causes only PCS1
(CS ) to go LOW. This is when the valid data will be transferred.
For both transfers, the DT register (delay after transfer) is
used to cause a 19µs delay. The interface is also set up to
wrap to the beginning of the queue. In this manner, the QSPI
is a state machine which generates the appropriate timing for
the ADS7806. This timing is thus locked to the crystal-based
timing of the microcontroller and not interrupt driven. So, this
interface is appropriate for both AC and DC measurements.
For the fastest conversion rate, the baud rate should be set to
2 (4.19MHz SCK), DT set to 10, the first serial transfer set to
eight bits, the second set to 12 bits, and DSCK disabled (in the
command control byte). This will allow for a 23kHz maximum
conversion rate. For slower rates, DT should be increased. Do
not slow SCK as this may increase the chance of affecting the
conversion results or accidently initiating a second conversion
during the first 8-bit transfer.
ADS7806
SBAS021B
PCS0
CPOL = 0
CPHA = 0
QSPI™ INTERFACING
ADS7806
www.ti.com
17
In addition, CPOL and CPHA should be set to zero (SCK
normally LOW and data captured on the rising edge). The
command control byte for the 8-bit transfer should be set to
20H and for the 12-bit transfer to 61H.
Convert Pulse
DSP56000
ADS7806
SPI™ INTERFACE
R/C
The SPI interface is generally only capable of 8-bit data
transfers. For some microcontrollers with SPI interfaces, it
might be possible to receive data in a similar manner as
shown for the QSPI interface in Figure 12. The microcontroller
will need to fetch the eight most significant bits before the
contents are overwritten by the least significant bits.
SC1
BUSY
SRD
SDATA
SCO
DATACLK
CS
EXT/INT
A modified version of the QSPI interface, see Figure 13,
might be possible. For most microcontrollers with SPI interface, the automatic generation of the start-of-conversion
pulse will be impossible and will have to be done with
software. This will limit the interface to ‘DC’ applications due
to the insufficient jitter performance of the convert pulse tself.
SYN = 0 (Asychronous)
BYTE
GCK = 1 (Gated clock)
SCD1 = 0 (SC1 is an input)
SHFD = 0 (Shift MSB first)
WL1 = 0 WL0 = 1 (Word length = 12 bits)
FIGURE 14. DSP56000 Interface to the ADS7806.
DSP56000 INTERFACING
The DSP56000 serial interface has an SPI compatibility
mode with some enhancements. Figure 14 shows an interface between the ADS7806 and the DSP56000 which is very
similar to the QSPI interface seen in Figure 12. As mentioned
in the QSPI section, the DSP56000 must be programmed to
enable the interface when a LOW-to-HIGH transition on SC1
is observed (BUSY going HIGH at the end of conversion).
The DSP56000 can also provide the convert pulse by including a monostable multi-vibrator as seen in Figure 15. The
receive and transmit sections of the interface are decoupled
(asynchronous mode) and the transmit section is set to
generate a word length frame sync every other transmit
frame (frame rate divider set to two). The prescale modulus
should be set to five.
The monostable multi-vibrator in this circuit will provide
varying pulse widths for the convert pulse. The pulse width
will be determined by the external R and C values used with
the multi-vibrator. The 74HCT123N data sheet shows that
the pulse width is (0.7)RC. Choosing a pulse width as close
to the minimum value specified in this data sheet will offer the
best performance. See the Starting A Conversion section of
this data sheet for details on the conversion pulse width.
The maximum conversion rate for a 20.48MHz DSP56000 is
35.6kHz. If a slower oscillator can be tolerated on the
DSP56000, a conversion rate of 40kHz can be achieved by
using a 19.2MHz clock and a prescale modulus of four.
SPI is a registered trademark of Motorola.
DSP56000
74HCT123N
+5V
+5V
R
B1
REXT1
C
SC2
CLR1
ADS7806
CEXT1
Q1
A1
R/C
SC0
DATACLK
SRD
SDATA
CS
SYN = 0 (Asychronous)
GCK = 1 (Gated clock)
SCD2 = 1 (SC2 is an output)
SHFD = 0 (Shift MSB first)
WL1 = 0 WL0 = 1 (Word length = 16 bits)
EXT/INT
BYTE
FIGURE 15. DSP56000 Interface to the ADS7806. Processor initiates conversions.
18
ADS7806
www.ti.com
SBAS021B
PACKAGE OPTION ADDENDUM
www.ti.com
15-Oct-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ADS7806U
NRND
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-40 to 85
ADS7806U
ADS7806U/1K
NRND
SOIC
DW
28
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-40 to 85
ADS7806U
ADS7806U/1KE4
NRND
SOIC
DW
28
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-40 to 85
ADS7806U
ADS7806UB
NRND
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-40 to 85
ADS7806U
B
ADS7806UB/1K
NRND
SOIC
DW
28
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-40 to 85
ADS7806U
B
ADS7806UE4
NRND
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-40 to 85
ADS7806U
ADS7806UG4
NRND
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU-DCC
Level-3-260C-168 HR
-40 to 85
ADS7806U
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
15-Oct-2015
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
ADS7806U/1K
SOIC
DW
28
1000
330.0
32.4
11.35
18.67
3.1
16.0
32.0
Q1
ADS7806UB/1K
SOIC
DW
28
1000
330.0
32.4
11.35
18.67
3.1
16.0
32.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADS7806U/1K
SOIC
DW
28
1000
367.0
367.0
55.0
ADS7806UB/1K
SOIC
DW
28
1000
367.0
367.0
55.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated