MITSUBISHI IGBT MODULES CM400HA-12H HIGH POWER SWITCHING USE INSULATED TYPE A Q M H N V–DIA.(4 TYP.) S E C E D G C CM F G X–M4 THD. (2 TYP.) W–M6 THD. (2 TYP.) P B K U K R E J L T E C E G Outline Drawing and Circuit Diagram Dimensions Inches A 4.21 Millimeters Dimensions Inches Millimeters 107.0 M 0.83 21.0 93.0±0.25 N 0.69 17.5 P 0.63 16.0 B 3.661±0.01 C 2.44 D 1.89±0.01 48.0±0.25 Q 0.51 13.0 E 1.42 Max. 36.0 Max. R 0.43 11.0 F 1.34 34.0 S 0.35 9.0 G 1.18 30.0 T 0.28 7.0 29.0 U 0.12 3.0 V 0.26 Dia. Dia. 6.5 62.0 H 1.14 J 0.98 Max. K 0.94 24.0 W M6 Metric M6 L 0.93 23.5 X M4 Metric M4 25.0 Max. Description: Mitsubishi IGBT Modules are designed for use in switching applications. Each module consists of one IGBT in a single configuration with a reverse-connected super-fast recovery free-wheel diode. All components and interconnects are isolated from the heat sinking baseplate, offering simplified system assembly and thermal management. Features: u Low Drive Power u Low VCE(sat) u Discrete Super-Fast Recovery Free-Wheel Diode u High Frequency Operation u Isolated Baseplate for Easy Heat Sinking Applications: u AC Motor Control u Motion/Servo Control u UPS u Welding Power Supplies Ordering Information: Example: Select the complete part module number you desire from the table below -i.e. CM400HA12H is a 600V (VCES), 400 Ampere Single IGBT Module. Type CM Current Rating Amperes VCES Volts (x 50) 400 12 Sep.1998 MITSUBISHI IGBT MODULES CM400HA-12H HIGH POWER SWITCHING USE INSULATED TYPE Absolute Maximum Ratings, Tj = 25 °C unless otherwise specified Ratings Symbol CM600HU-12H Units Junction Temperature Tj -40 to 150 °C Storage Temperature Tstg -40 to 125 °C Collector-Emitter Voltage (G-E SHORT) VCES 600 Volts Gate-Emitter Voltage (C-E SHORT) VGES ±20 Volts IC 400 Amperes ICM 800* Amperes Collector Current (Tc = 25°C) Peak Collector Current (Tj ≤ 150°C) Emitter Current** (Tc = 25°C) IE 400 Amperes Peak Emitter Current** IEM 800* Amperes Maximum Collector Dissipation (Tc = 25°C) Pc 1500 Watts Mounting Torque, M6 Main Terminal – 1.96~2.94 N·m Mounting Torque, M6 Mounting – 1.96~2.94 N·m Mounting Torque, M4 Terminal – 0.98~1.47 N·m – 400 Grams Viso 2500 Vrms Weight Isolation Voltage (Main Terminal to BAseplate, AC 1 min.) * Pulse width and repetition rate should be such that the device junction temperature (Tj) does not exceed Tj(max) rating. **Represents characteristics of the anti-parallel, emitter-to-collector free-wheel diode (FWDi). Static Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Symbol Test Conditions Min. Max. Units Collector-Cutoff Current ICES VCE = VCES, VGE = 0V – Typ. – 1.0 mA Gate Leakage Current IGES VGE = VGES, VCE = 0V – – 0.5 µA Gate-Emitter Threshold Voltage V GE(th) IC = 40mA, VCE = 10V 4.5 6.0 7.5 Volts Collector-Emitter Saturation Voltage VCE(sat) IC = 400A, VGE = 15V – 2.1 2.8** Volts IC = 400A, VGE = 15V, Tj = 150°C – – Volts Total Gate Charge QG VCC = 400V, IC = 400A, VGE = 15V – 1200 – nC Emitter-Collector Voltage VEC IE = 400A, VGE = 0V – – 2.15 2.8 Volts ** Pulse width and repetition rate should be such that device junction temperature rise is negligible. Dynamic Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Symbol Input Capacitance Cies Output Capacitance Coes Test Conditions VGE = 0V, VCE = 10V Min. Typ. Max. Units – – 40 nF – – 14 nF Reverse Transfer Capacitance Cres – – 8 nF Resistive Turn-on Delay Time td(on) – – 350 ns Load Rise Time Switching Turn-off Delay Time Times tr VCC = 300V, IC = 400A, – – 600 ns td(off) VGE1 = VGE2 = 15V, RG = 1.6Ω – – 350 ns Fall Time tf – – 300 ns Diode Reverse Recovery Time trr IE = 400A, diE/dt = –800A/µs – – 110 ns Diode Reverse Recovery Charge Qrr IE = 400A, diE/dt = –800A/µs – 1.08 – µC Thermal and Mechanical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Thermal Resistance, Junction to Case Rth(j-c) Per IGBT – – Max. 0.085 Units °C/W Thermal Resistance, Junction to Case Rth(j-c) Per FWDi – – 0.18 °C/W Contact Thermal Resistance Rth(c-f) Per Module, Thermal Grease Applied – – 0.040 °C/W Sep.1998 MITSUBISHI IGBT MODULES CM400HA-12H HIGH POWER SWITCHING USE INSULATED TYPE COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) OUTPUT CHARACTERISTICS (TYPICAL) 5 VGE = 20V 15 600 11 400 10 200 9 7 8 VGE = 15V Tj = 25°C Tj = 125°C 4 3 2 1 0 2 4 6 8 10 VCE = 10V Tj = 25°C Tj = 125°C 600 400 200 0 0 0 0 200 400 600 0 800 4 8 12 16 20 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) COLLECTOR-CURRENT, IC, (AMPERES) GATE-EMITTER VOLTAGE, VGE, (VOLTS) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) CAPACITANCE VS. VCE (TYPICAL) 102 103 10 Tj = 25°C 8 IC = 800A 6 IC = 400A 4 2 CAPACITANCE, Cies, Coes, Cres, (nF) Tj = 25°C EMITTER CURRENT, IE, (AMPERES) 102 Cies 101 Cres 100 Coes IC = 160A VGE = 0V 10-1 10-1 101 0 4 8 12 16 0 20 1.6 2.4 3.2 4.0 HALF-BRIDGE SWITCHING CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CHARACTERISTICS (TYPICAL) 103 REVERSE RECOVERY TIME, t rr, (ns) td(off) tf td(on) 102 VCC = 300V VGE = ±15V RG = 1.6Ω Tj = 125°C tr 102 COLLECTOR CURRENT, IC, (AMPERES) 103 Irr t rr 101 di/dt = -800A/µsec Tj = 25°C 101 101 102 EMITTER CURRENT, IE, (AMPERES) 101 102 GATE CHARGE, VGE 102 102 100 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) EMITTER-COLLECTOR VOLTAGE, VEC, (VOLTS) 103 101 101 0.8 GATE-EMITTER VOLTAGE, VGE, (VOLTS) 100 103 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) 0 REVERSE RECOVERY CURRENT, Irr, (AMPERES) COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 800 12 COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) COLLECTOR CURRENT, IC, (AMPERES) Tj = 25oC COLLECTOR CURRENT, IC, (AMPERES) 800 SWITCHING TIME, (ns) TRANSFER CHARACTERISTICS (TYPICAL) IC = 400A 16 VCC = 200V 12 VCC = 300V 8 4 0 0 400 800 1200 1600 2000 GATE CHARGE, QG, (nC) Sep.1998 MITSUBISHI IGBT MODULES CM400HA-12H 10-3 101 100 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) 10-2 10-1 100 101 Single Pulse TC = 25°C Per Unit Base = R th(j-c) = 0.085°C/W 10-1 10-1 10-2 10-2 10-3 10-5 TIME, (s) 10-4 10-3 10-3 NORMALIZED TRANSIENT THERMAL IMPEDANCE, Z th(j-c) Zth = Rth • (NORMALIZED VALUE) NORMALIZED TRANSIENT THERMAL IMPEDANCE, Z th(j-c) Zth = Rth • (NORMALIZED VALUE) HIGH POWER SWITCHING USE INSULATED TYPE 10-3 101 100 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) 10-2 10-1 100 101 Single Pulse TC = 25°C Per Unit Base = R th(j-c) = 0.18°C/W 10-1 10-1 10-2 10-2 10-3 10-5 10-4 10-3 10-3 TIME, (s) Sep.1998