Technical Data Sheet for CM35-1.9 Commercial Module for CATV & SLED Applications NOMINAL PERFORMANCE IN NITROGEN Hot Side Temperature (°C) Δ Tmax (°C): Qmax (watts): Imax (amps): Vmax (vdc): AC Resistance (ohms): PRODUCT FEATURES • • • • • 27 71 5.2 1.9 4.2 1.87 85 92 6.2 1.8 5.3 --- ORDERING OPTIONS RoHS EU Compliant Ceramic Material: Aluminum Oxide (AC) or Aluminum Nitride (AN) Au flash exterior, suitable for soldering. Maximum process temperature is 220°C. Height includes metallization, where applicable, and excludes tinning. Model Number CM35-1.9-01AC CM35-1.9-04AC CM35-1.9-05AC CM35-1.9-06AC CM35-1.9-07AC CM35-1.9-08AN CM35-1.9-09AN Description TEM, Top and Base Metallized Exterior, ALO Ceramics -01AC, Top and Base Pre-Tinned w/146°C Solder -01AC, Top and Base Pre-Tinned w/138°C Solder -01AC, Top and Base Pre-Tinned w/183°C Solder -01AC, Top and Base Pre-Tinned w/118°C Solder TEM, Top and Base Metallized Exterior, ALN Ceramics TEM, No Metallized Exterior, ALN Ceramics OPERATION CAUTIONS INSTALLATION For maximum reliability, storage and operation below 85°C in a non-condensing environment is recommended. To minimize thermal stress, use linear/proportional temperature control or a similar method rather than an ON/OFF method. Recommended mounting methods: Bonding with thermal epoxy or soldering with metallized ceramics. For additional information, please refer to our TEC Installation Guide. II-VI Marlow – Dallas, TX USA 214-340-4900 877-627-5691 [email protected] Marlow Industries Europe GmbH - Germany +49 (0) 6150 5439 - 403 [email protected] II-VI Japan Inc. 81 43 297 2693 (tel) [email protected] www.ii-vi.co.jp MI Form 005-0808 Rev. A www.marlow.com II-VI Singapore Pte., Ltd. (65) 6481 8215 (tel) [email protected] Marlow Industries China, II-VI Technologies Beijing 86-10-643 98226 [email protected] DOC # 102-0355 REV F - PAGE 1 OF 2 A = 27°C - Vacuum HotTSide Temperature 27°C 100.0 = 85°C - Vacuum HotTASide Temperature 85°C Heat Heat Load (W) 100.0 Load (W) 0.00 80.0 80.0 1.00 0.00 1.00 2.00 40.0 2.00 60.0 ∆T (°C) ∆T (°C) 60.0 3.00 40.0 4.00 3.00 20.0 20.0 4.00 0.0 0.4 0.8 1.2 1.6 2.0 5.0 5.0 Voltage (VDC) 6.0 Q=0 3.0 2.0 ∆T = 0 6.00 0.0 6.0 4.0 5.00 0.0 5.00 0.0 Voltage (VDC) TYPICAL PERFORMANCE CURVES ENVIRONMENT: ONE ATMOSPHERE DRY NITROGEN 0.4 0.8 1.2 1.6 2.0 Q=0 4.0 3.0 2.0 ∆T = 0 1.0 1.0 0.0 0.0 0.0 0.4 0.8 1.2 1.6 2.0 Current (amps) 0.0 0.4 0.8 1.2 1.6 2.0 Current (amps) MECHANICAL CHARACTERISTICS For performance information in a vacuum or with hot side temperatures other than 27°C or 85°C, contact one of our Applications Engineers at 877-627-5691. All dimensions are in millimeters unless otherwise stated. For customer support or general questions please contact a local office or visit our website at www.marlow.com. MI Form 005-0808 Rev. A www.marlow.com DOC # 102-0355 REV F - PAGE 2 OF 2