3. 0mmx1.0 mm RIGHT ANGLE SMD CHIP LED LAMP ATTENTION Part Number: APPA3010SURCK Hyper Red OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 3.0x2.5x1.0mm right angle SMD LED, 1.0mm thickness. z The Hyper Red source color devices are made with Al GaInP on GaAs substrate Light Emitting Diode. z Low power consumption. z Ideal for back light and indicator. z Electrostatic discharge and power surge could damage the LEDs. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z Tinned pads for improved solderability. z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs. z All devices, equipment and machinery must be electri z RoHS compliant. cally grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAP0944 REV NO: V.1A DATE: MAR/01/2017 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203004347 Selection Guide Part No. Emitting Color (Material) APPA3010SURCK Iv (mcd) [2] @ 20mA Lens Type Hyper Red (AlGaInP) Water Clear Viewing Angle [1] Min. Typ. 500 800 *200 *300 2θ1/2 30° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Hyper Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 645 nm IF=20mA Hyper Red 630 nm IF=20mA Spectral Line Half-width Hyper Red 28 nm IF=20mA C Capacitance Hyper Red 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.95 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR=5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAP0944 REV NO: V.1A DATE: MAR/01/2017 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203004347 Hyper Red APPA3010SURCK SPEC NO: DSAP0944 REV NO: V.1A DATE: MAR/01/2017 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203004347 APPA3010SURCK Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAP0944 REV NO: V.1A DATE: MAR/01/2017 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203004347 PACKING & LABEL SPECIFICATIONS APPA3010SURCK Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAP0944 REV NO: V.1A DATE: MAR/01/2017 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203004347