1.0X0.5mm SMD CHIP LED LAMP Part Number: APHHS1005LSECK/J4-PF Super Bright Orange Features Description z 1.0mmX0.5mm SMD LED, 0.5mm thickness. The Orange source color devices are made with AlGaInP z Low power consumption. Light Emitting Diode. z Wide viewing angle. z Ideal for backlight and indicator. z Package: 2000pcs / reel . z Moisture sensitivity level : level 3. z Low current IF=2mA operating. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAO4040 REV NO: V.1A DATE: JUL/06/2015 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015115 Selection Guide Part No. Emitting Color (Material) APHHS1005LSECK/J4-PF Lens Type Super Bright Orange (AlGaInP) Iv (mcd) [2] @ 2mA Viewing Angle [1] Min. Typ. 2θ1/2 50 100 *20 *40 Units Test Conditions 120° Water Clear Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Min. Symbol Parameter Emitting Color λpeak Peak Wavelength Super Bright Orange 611 nm IF=2mA λD [1] Dominant Wavelength Super Bright Orange 605 nm IF=2mA Δλ1/2 Spectral Line Half-width Super Bright Orange 17 nm IF=2mA C Capacitance Super Bright Orange 27 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Orange 2.1 V IF=2mA IR Reverse Current Super Bright Orange 10 uA VR=5V 1.5 Typ. 1.8 Max. Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 63 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAO4040 REV NO: V.1A DATE: JUL/06/2015 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015115 Super Bright Orange APHHS1005LSECK/J4-PF SPEC NO: DSAO4040 REV NO: V.1A DATE: JUL/06/2015 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015115 APHHS1005LSECK/J4-PF Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAO4040 REV NO: V.1A DATE: JUL/06/2015 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015115 PACKING & LABEL SPECIFICATIONS APHHS1005LSECK/J4-PF Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAO4040 REV NO: V.1A DATE: JUL/06/2015 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015115