AZ762P 20 A SPDT MINIATURE POWER RELAY FEATURES • • • • • • Latching relay Dielectric strength 4400 Vrms Epoxy sealed versions available 20 Amp switching High inrush current 500A / 2ms available UL, CUR file E44211 CONTACTS Arrangement Ratings GENERAL DATA SPDT (1 Form C) SPST (1 Form A, 1 Form B) Resistive load: Max. switched power: 5000 VA Max. switched current: 20 A Max. switched voltage: 277 VAC Rated Load UL, CUR 20A at 250 VAC, Resistive, 20k cycles [1] 16A at 250 VAC, Resistive, 100k cycles [1] 1.5 HP at 250 VAC, Motor, 6k cycles [1] .5 HP at 120 & 250 VAC, Motor, 20k cycles (form A) [1] TV-8 at 240VAC, 25k cycles (form A) [1] Tungsten 1662W 6A at 277VAC, 6k cycles (form A) [1] Tungsten 1800W 15A at 120VAC, 20k cycles (form A) [1] Electronic ballast 1800W 15A at 120VAC, 20k cycles (form A) [1] Standard ballast 1662W 6A at 277VAC, 6k cycles (form A) [1] ‘T’ High Inrush Version (Form A 5.0mm Only) 3300W at 277VAC, Electronic Ballast, 20k cycles [2] 3000W at 220VAC, Tungsten, 6k cycles [2] 1500W at 347VAC, Std. Ballast, 20k cycles [2] Material [1] Silver tin oxide, [2] Tungsten/Silver tin oxide Resistance < 50 milliohms initially (at 1A, 24 VDC) COIL Power At Pickup Voltage (typical) 1 Coil: 256 mW 2 Coils: 384 mW Max. Continuous Dissipation 1 Coil: 0.4 W 2 Coils: 0.6 W Temperature Rise 26°C (47°F) at nominal coil voltage Max. Temperature 130°C (266°F) Life Expectancy Mechanical Electrical Minimum operations 1 x 10 6 1 x 10 5 at 16 A 250 VAC Res. Set Time (typical) 15 ms at nominal coil voltage Reset Time (typical) 15 ms at nominal coil voltage (with no coil suppression) Min. Pulse Time 75ms Max Pulse Time 1 min. Dielectric Strength (at sea level for 1 min.) 4400 VAC coil to contact 1000 VAC between open contacts Surge Voltage Coil to Contact 10,000V (at 1.2x50 µ s) Insulation Resistance 1000 megohms min. at 20°C 500 VDC 50% RH Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) 0°C (32°F) to 40°C (104°F) Vibration 0.062" DA at 10–55 Hz Shock 10 g Enclosure P.B.T. polyester Terminals Tinned copper alloy, P. C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Weight 13 g NOTES 1. All values at 23°C (73.4°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 4. Check the relay set/reset state before energizing the relay in application. 11/17/15 AZ AZ762P RELAY ORDERING DATA COIL SPECIFICATIONS - SINGLE COIL LATCHING Nominal Coil VDC 3 ORDER NUMBER* Must Operate VDC 2.4 Max. Continuous VDC 3.9 5 4.0 6.5 Coil Resistance ±10% 22.5 Unsealed Sealed AZ762P1–1CE–3D AZ762P1–1CE–3DE 62.5 AZ762P1–1CE–5D AZ762P1–1CE–5DE 6 4.8 7.8 90 AZ762P1–1CE–6D AZ762P1–1CE–6DE 12 9.6 15.6 360 AZ762P1–1CE–12D AZ762P1–1CE–12DE 24 19.2 31.2 1,440 AZ762P1–1CE–24D AZ762P1–1CE–24DE COIL SPECIFICATIONS - DUAL COIL LATCHING Nominal Coil VDC 3 5 6 12 24 Must Operate VDC 2.4 4.0 4.8 9.6 19.2 Max. Continuous VDC 3.9 6.5 7.8 15.6 31.2 ORDER NUMBER* Coil 1 Resistance ±10% 15 42 60 240 886 Coil 2 Unsealed Resistance ±10% 15 AZ762P2–1CE–3D 42 AZ762P2–1CE–5D 60 AZ762P2–1CE–6D 240 AZ762P2–1CE–12D 886 AZ762P2–1CE–24D Sealed AZ762P2–1CE–3DE AZ762P2–1CE–5DE AZ762P2–1CE–6DE AZ762P2–1CE–12DE AZ762P2–1CE–24DE * Substitute “1A” or “1B” in place of “1C” for Form A or B respectively. Form A relay is in the reset postion. Form B relay is in the set position. Add suffix “K” for 3.5mm pin spacing version. Replace ‘1AE’ with ‘1AT’ for W+AgSnO2 high inrush contacts (Form A, 5.0mm pin spacing only). Add suffix “L” for 2.5mm pin spacing version. Note, Form C only available in 5.0mm and 3.5mm pin spacing. Add suffix “R” for reversed polarity coil. WIRING DIAGRAM 11/17/15 AZ762P MECHANICAL DATA PCB LAYOUT 5.0mm Spacing - Standard No terminal on 1 Form A No terminal for single coil version VIEWED TOWARD TERMINALS 3.5mm Spacing - Suffix “K” No terminal on 1 Form A No terminal for single coil version VIEWED TOWARD TERMINALS 2.5mm Spacing - Suffix “L” No terminal for single coil version VIEWED TOWARD TERMINALS Dimensions in metric. 11/17/15