Click on Series name for product info on aimtec.com Series AMEOW10-NZ 10 Watt | AC-DC / DC-DC Converter FEATURES: • • • • Open Frame design 4000 VAC Isolation 3 or 4 wire three phase input Over-voltage protection • • • • Very wide input range Low Ripple & Noise High Efficiency Low Standby Power < 0.55W Models Dual output Model Input Voltage (VAC/Hz) Input Voltage (VDC) Temperature range (ºC) Output Voltage (V) AMEOW10-5S12S-NZ 65-460 / 47-440 90-650 -40 to +70 5.1 12 Output Current max (A) 1.2 0.4 Maximum capacitive load (µF) Efficiency (%) 4000 1200 78 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. All specifications are in reference to input voltage Vin=220VAC. Input Specifications Parameters Current Inrush current <2ms Leakage current External fuse Input dissipation Under voltage protection Input Over Voltage Shutdown Output Specifications Parameters Conditions Typical Vin=220VAC Vin=220VAC Slow Blow Type Vin=220VAC, 100% load 25A 0.3 3.15A 250V 13.5 56 Vin=220VAC 100 Conditions Typical Vo1: 5 Vo2: ± 10 Vo1: ± 0.5 Vo2: ± 1.5 Vo1: ± 3 Vo2: ± 5 Vo1: ± 3 Vo2: ± 12 2000 ± 100 Voltage accuracy Line regulation 10 – 100% Load regulation Balanced Load Cross regulation Transient recovery time Transient response deviation Ripple & Noise Vin=220VAC Isolation Specifications Parameters Tested I/O voltage Output V1 V2 Isolation General Specifications Parameters Switching frequency Start up time www.aimtec.com F 052e R8.B Conditions Conditions µs mV V1: 100 V2: 200 mV p-p ms % Rated 4000 Reinforced isolation 63 500 1 of 5 Units % Typical Tel: +1 514 620 2722 Maximum % Typical 60s > 50MΩ 4000 VAC 750 ± 50 A mA A W VAC Vdc mA % 200 V1: ± 3 V2: ± 10 Voltage adjustment range Units % 20MHz Bandwidth Hold-up time (min) Maximum Units VAC Maximum Units KHz mS Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEOW10-NZ 10 Watt | AC-DC / DC-DC Converter General Specifications (continue) Parameters Over current protection Over voltage protection Short circuit protection Short circuit restart Operating temperature Storage temperature Cooling Conditions Typical Io1 & Io2 = 100% 110~250%, Auto Recovery Clamp Diode Continuous Auto Recovery -40 to +70 -40 to +85 Free Air Convection Altitude < 3000 meters Temperature coefficient Humidity Weight Dimensions (L x W x H) MTBF Parameters Acceleration amplitude Bump duration Shock Conditions % % o V1: ±0.02 V2: ±0.06 C C % / oC % RH g 196.1 m/s² 11 ms Number of bumps Along x, y, z, once each 10 ~ 55 Hz Test mode Displacement Acceleration Vibration Units o 20 - 90 95 3.94 (L) x 1.97 (W) x 1.38 (H) inches 100 (L) x 50 (W) x 35 (H) mm > 300,000h @25°C Environment Approval Test Maximum 3 minutes / cycle 19.6 m/s² 60 minutes Converter operation Safety Specifications Parameters Standards Designed to meet : IEC EN61000-4-4, IEC EN61000-4-5, EN 55022 class B Pin Out Specifications Pin 1 2 3 4 5 6 Designation AC Input (L) AC Input (N) Output +12 V Output -12 V Output -5 V Output +5 V www.aimtec.com F 052e R8.B Tel: +1 514 620 2722 2 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEOW10-NZ 10 Watt | AC-DC / DC-DC Converter Typical Applications C1 C2 TVS RL + L L + Vo1 - C3 L/N N Vo2 C4 RL + + Device C1 C2 C3 C4 TVS Value 220 µF / 10V 0.1 µF / 50V 100µF / 25V 0.1 µF / 50V TVS 600W 6.8V UNIDIRECT DO204AC P6KE6.8A It is recommended that the 5V output adds TVS (transient voltage suppressor) to protect adjacent circuits (if device fails), the 12 V output has TVS protection internally, so not required. Three phase four wire full wave rectification application: L1 L2 Common Mode Inductor >3mH Winding Resistor 5 ~ 10Ω L 47 µF FUSE 3.15A Winding Resistor 5 ~ 10Ω + FUSE 3.15A L3 Winding Resistor 5 ~ 10Ω FUSE 3.15A N FUSE 3.15A www.aimtec.com F 052e R8.B 47 µF + 560K Ω 560K Ω Vo1 - 560K Ω 560K Ω Vo2 N Varistor 911KD20 Capacitor 0.1µF 300VAC Safety X1 Level Capacitor 0.1µF 300VAC Safety X1 Level Tel: +1 514 620 2722 3 of 5 + + IN4007X2 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEOW10-NZ 10 Watt | AC-DC / DC-DC Converter Three phase four wire half wave rectification application: Common Mode Inductor >3mH Winding Resistor 5 ~ 10Ω L1 L 47 µF FUSE 3.15A Winding Resistor 5 ~ 10Ω L2 + IN4007X2 FUSE 3.15A L3 Winding Resistor 5 ~ 10Ω FUSE 3.15A 47 µF Capacitor 0.1µF 300VAC Safety X1 Level FUSE 3.15A 560K Ω 560K Ω Vo1 560K Ω 560K Ω - - Vo2 N Varistor 911KD20 N + + + Capacitor 0.1µF 300VAC Safety X1 Level Derating Free Air Convection 60 º C Output Power % 100 80 60 Safe Operating Area 40 20 0 - 40 - 20 0 20 40 60 Ambient Temperature www.aimtec.com F 052e R8.B 80 ºC 100 Tel: +1 514 620 2722 4 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEOW10-NZ 10 Watt | AC-DC / DC-DC Converter Dimensions Dimensions mm (inch) 4.5 (0.17) 10 (0.39) 31 (1.22) Φ 2 ± 0.15 41 (1.61) 6 5 41 (1.61) 50 ±1 (1.97±0.04) 1 4 3 2 4 (0.16) 0.5 (0.02) 2.5±0.15 (0.10±0.006) 1.5±0.15 (0.06±0.006) 1.2 (0.05) 1.6 (0.06) 4.8 (0.19) 4.8 (0.19) 35 (1.38) MAX 92 (3.62) 100 ±1 (3.94±0.04) 92 (3.62) 100 ±1 (3.94±0.04) NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 052e R8.B Tel: +1 514 620 2722 5 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only