ASL360 Wideband Linear Amplifier MMIC Features Description ·17.3 dB Gain at 500 Mz ·21 dBm P1dB at 500 MHz ·40 dBm Output IP3 at 500 MHz ·1.6 dB NF at 500 MHz ·75 Ohm Input / Output Match ·Bandwidth 5 ~ 1000 MHz ·Single Supply 5 V The ASL360, a wideband linear amplifier MMIC, has a high linearity and low noise over a wide range of frequency 5 MHz to 1 GHz, being suitable for use in the fiber receiver, distribution amplifiers and drop amplifiers of CATV systems, and in the mobile wireless repeaters and BTS. The amplifier is available in ASL360 an SOT-89 package and passes through the stringent DC, RF, and reliability tests. Package Style: SOT-89 Typical Performance Parameters Units Frequency Application Circuit Typical MHz 5 50 500 860 2150 Noise Figure dB 1.8 1.5 1.6 1.7 2.3 Gain dB 17.9 17.3 17.3 17.2 15.4 S11 dB -18 -17 -15 -15 -10 S22 dB -16 -17 -17 -15 -8 Output P1dB dBm 19 21 21 17 17 Output IP3 dBm 34.5 dBm 36 Output IP2 1),2),3) 41.5 53 2) 40 2) dBc dBc 75 mA 110 V 5 Device Voltage 2) 36.5 62 4) Current 34 53 4) CSO CTB 1) · 50 ~ 1000 MHz · 5 ~ 200 MHz · 950 ~ 2150 MHz (SMATV) · 50 ~ 1000 MHz (Push-Pull / 1:1 transformer) 2) - · 5 ~ 200 MHz (Push-Pull / 1:1 transformer) 60 1) OIP3 and OIP2 are measured with two tones at an output power of +8 dBm/tone separated by 1 MHz. 2) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 6 MHz. 3) OIP2 is measured at F1+F2 Frequency. 4) 60 channels, +33 dBmV per channel (measured at output). Product Specifications Parameters Testing Frequency Units Min Typ MHz 500 Gain dB 16.3 17.3 S11 dB -12 -15 S22 dB -15 -17 dBm 37 40 Output IP3 Noise Figure dB Output P1dB dBm 20 21 Current mA 95 110 Device Voltage V Max 1.6 1.8 125 5 Absolute Maximum Ratings Parameters Rating Operating Case Temperature -40 to +85°C Storage Temperature -40 to +150°C Device Voltage +6V Operating Junction Temperature +160°C Input RF Power (CW, 75ohm matched) 5 dBm Maximum Current 150 mA Thermal Resistance 43 °C/W 1/8 ASB Inc. · [email protected] · Tel: +82-42-528-7223 September 2011 ASL360 Wideband Linear Amplifier MMIC Outline Drawing Part No. Lot No. Symbols A L b b1 C D D1 E E1 e1 H S e ASL360 Pxxxx Dimensions (In mm) MIN NOM MAX 1.40 1.50 1.60 0.89 1.04 1.20 0.36 0.42 0.48 0.41 0.47 0.53 0.38 0.40 0.43 4.40 4.50 4.60 1.40 1.60 1.75 3.64 --4.25 2.40 2.50 2.60 2.90 3.00 3.10 0.35 0.40 0.45 0.65 0.75 0.85 1.40 1.50 1.60 Pin No. Function 1 RF IN 2 GND 3 RF OUT / Bias Mounting Recommendation (in mm) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal and RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of the lead pin 2 and exposed pad of the device for better RF and thermal performance, as shown in the drawing at the left side. ESD Classification & Moisture Sensitivity Level ESD Classification HBM Class 1B Voltage Level: 550 V MM Class A Voltage Level: 50 V CAUTION: ESD-sensitive device! Moisture Sensitivity Level (MSL) Level 3 at 260°C reflow 2/8 ASB Inc. · [email protected] · Tel: +82-42-528-7223 September 2011 ASL360 Wideband Linear Amplifier MMIC Frequency (MHz) APPLICATION CIRCUIT CATV 50 500 860 Noise Figure (dB) 1.5 1.6 1.7 Magnitude S21 (dB) 17.3 17.3 17.2 Magnitude S11 (dB) -17 -15 -15 Magnitude S22 (dB) -17 -17 -15 Output P1dB (dBm) 21 21 17 41.5 40 34 53 53 62 1) Output IP3 (dBm) 50 ~ 1000 MHz Output IP2 +5 V 1),2) (dBm) 3) 60 3) 75 CSO (dBc) CTB (dBc) Device Voltage (V) 5 Current (mA) 110 1) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. 3) 60 channels, +33 dBmV per channel (measured at output). Schematic Board Layout (FR4, 40x40 mm2, 0.8T) Vs=5 V * Note: Gain slope can be adjusted by L5 and R1 values at the expense of S11 & S22. C6=10 uF L1=1 uH (LQH31CN1R0M03) RF IN C1=100 pF L2=12 nH C2=100 nF C3=470 pF RF OUT ASL360 L4=3.3 nH L3=330 nH (Coil Inductor) C4=0.75 pF C5=0.3 pF L5=68 nH R1=240 W S-parameters 25 0 20 -5 15 -10 10 o -40 c o 25 c o 85 c 5 0 S11 (dB) Gain (dB) o 0 100 200 300 400 500 600 700 800 900 -40 c o 25 c o 85 c -15 -20 1000 -25 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Frequency (MHz) 0 o -40 c o 25 c o 85 c -5 S22 (dB) -10 -15 -20 -25 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 3/8 ASB Inc. · [email protected] · Tel: +82-42-528-7223 September 2011 ASL360 Wideband Linear Amplifier MMIC Gain vs. Temperature Current vs. Temperature 22 200 20 18 Gain (dB) Current (mA) 150 100 16 50 Frequency = 860 MHz 14 0 -60 -40 -20 0 20 40 60 80 12 -60 100 -40 -20 0 20 40 60 80 100 o o Temperature ( C) Temperature ( C) P1dB vs. Temperature 30 25 P1dB (dBm) 20 15 10 Frequency = 860 MHz 5 0 -60 -40 -20 0 20 40 60 80 100 o Temperature ( C) Output IP3 vs. Tone Power (Frequency = 860 MHz) Output IP2 vs. Tone Power (Frequency = 860 MHz) 50 90 45 80 40 70 Output IP2 (dBm) Output IP3 (dBm) 35 30 25 20 o -40 c o 25 c o 85 c 15 10 40 30 o -40 c o 25 c o 85 c 20 10 5 0 60 50 -1 0 1 2 3 4 5 6 7 8 9 10 11 0 -1 0 1 Pout per Tone (dBm) 4/8 2 3 4 5 6 7 8 9 10 11 Pout per Tone (dBm) ASB Inc. · [email protected] · Tel: +82-42-528-7223 September 2011 ASL360 Wideband Linear Amplifier MMIC Frequency (MHz) APPLICATION CIRCUIT CATV 5 ~ 200 MHz 5 50 200 Noise Figure (dB) 1.8 1.5 1.5 Magnitude S21 (dB) 17.9 18.1 17.1 Magnitude S11 (dB) -18 -20 -18 Magnitude S22 (dB) -16 -20 -16 Output P1dB (dBm) 19 21.5 22 34.5 42 44 36 55 57 1) Output IP3 (dBm) Output IP2 +5 V 1),2) (dBm) Device Voltage (V) 5 Current (mA) 110 . 1) OIP3 and OIP2 are measured with two tones at an output power of +8 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency Board Layout (FR4, 40x40 mm2, 0.8T) Schematic Vs=5 V C4=10 uF L1=27 uH C1=10 nF RF IN C2=820 pF RF OUT ASL360 L2=4.7 uH R2=1.2 kW C3=10 nF R1=75 W L3=8.2 uH S-parameters 25 0 -5 -10 15 S11 (dB) Gain (dB) 20 10 -15 -20 5 0 -25 0 50 100 150 200 -30 0 Frequency (MHz) 50 100 150 200 Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 -30 0 50 100 150 200 Frequency (MHz) 5/8 ASB Inc. · [email protected] · Tel: +82-42-528-7223 September 2011 ASL360 Wideband Linear Amplifier MMIC Frequency (MHz) APPLICATION CIRCUIT SMATV 950 ~ 2150 MHz 950 2150 Noise Figure (dB) 1.8 2.3 2.3 Magnitude S21 (dB) 17.3 16.6 15.4 Magnitude S11 (dB) -7 -8 -10 Magnitude S22 (dB) -12 -12 -8 Output P1dB (dBm) 18 17 17 34.5 37 36.5 1) Output IP3 (dBm) +5 V 1500 Device Voltage (V) 5 Current (mA) 110 . 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1 MHz. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic Vs=5 V C4=1 mF L1=8.2 nH C1=100 pF RF IN C2=100 pF RF OUT ASL360 L2=12 nH C3=1 pF 20 0 15 -5 S11 (dB) Gain (dB) S-parameters 10 5 0 -10 -15 0 500 1000 1500 2000 2500 -20 0 Frequency (MHz) 500 1000 1500 2000 2500 Frequency (MHz) 0 S22 (dB) -5 -10 -15 -20 0 500 1000 1500 2000 2500 Frequency (MHz) 6/8 ASB Inc. · [email protected] · Tel: +82-42-528-7223 September 2011 ASL360 Wideband Linear Amplifier MMIC Frequency (MHz) 50 500 860 Magnitude S21 (dB) 12.3 12 11.7 Magnitude S11 (dB) -18 -16 -17 Magnitude S22 (dB) -18 -14 -14 CATV Push-Pull Output P1dB (dBm) 24.5 25 25.5 1 : 1 transformer Output IP3 (dBm) 40 44.5 42.5 APPLICATION CIRCUIT 1) Output IP2 50 ~ 1000 MHz 1),2) (dBm) Noise Figure (dB) +5 V 65 66 64 2.7 2.7 2.7 Device Voltage (V) 5 Current (mA) 220 . 1) OIP3 and OIP2 are measured with two tones at an output power of +10 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. Schematic Board Layout (FR4, 40x40 mm2, 0.8T) Vs=5 V Note: MABA-007159 1:1 impedance transformers are used. C4=10 uF L1=1 uH (LQH31CN1R0M03) C2=1 uF C1=1 uF ASL360 RF OUT R1=330 W C3=1 uF 1:1 transformer RF IN 1:1 transformer C5=1 uF C6=1 uF ASL360 C7=1 uF R2=330 W L2=1 uH (LQH31CN1R0M03) C8=10 uF Vs=5 V S-parameters 0 20 -5 -10 S11 (dB) Gain (dB) 15 10 -15 5 -20 0 0 100 200 300 400 500 600 700 800 900 1000 -25 0 100 Frequency (MHz) 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 7/8 ASB Inc. · [email protected] · Tel: +82-42-528-7223 September 2011 ASL360 Wideband Linear Amplifier MMIC Frequency (MHz) 5 50 200 Magnitude S21 (dB) 13.2 12.3 12.2 Magnitude S11 (dB) -20 -18 -17 Magnitude S22 (dB) -20 -18 -17 CATV Push-Pull Output P1dB (dBm) 22.5 24.5 25 1 : 1 transformer Output IP3 (dBm) 32 42 44.5 APPLICATION CIRCUIT 1) Output IP2 5 ~ 200 MHz 1),2) (dBm) Noise Figure (dB) +5 V 48 56 72 3.3 2.7 2.8 Device Voltage (V) 5 Current (mA) 220 . 1) OIP3 and OIP2 are measured with two tones at an output power of +7 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency. Schematic Board Layout (FR4, 40x40 mm2, 0.8T) Vs=5 V Note: MABA-007159 1:1 impedance transformers are used. C3=10 uF L1=15 uH C1=1 uF C2=1 nF ASL360 RF OUT R1=330 W C4=1 uF 1:1 transformer RF IN 1:1 transformer C5=1 uF C6=1 nF ASL360 C7=1 uF R2=330 W L2=15 uH C8=10 uF Vs=5 V S-parameters 0 20 -5 -10 S11 (dB) Gain (dB) 15 10 -15 5 -20 0 0 50 100 150 200 -25 0 50 100 150 200 Frequency (MHz) Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 0 50 100 150 200 Frequency (MHz) 8/8 ASB Inc. · [email protected] · Tel: +82-42-528-7223 September 2011