CRA04P Vishay Thick Film, Resistor Array FEATURES • Concave terminal array with square corners • • • • Wide ohmic range: 1R0 to 1M0 8 terminal package with isolated resistors Lead (Pb)-free solder contacts on NI barrier layer Pure tin plating provides compatibility with lead (Pb)-free and lead containing soldering processes • Compatible with “Restriction of the use of Hazardous Substances” (RoHS) directive 2002/95/EC (issue 2004) The CRA04P thick film resistor array is constructed on a high grade ceramic body with concave terminations. A small package enables the design of high density circuits. The single component reduces board space, component counts and assembly costs. STANDARD ELECTRICAL SPECIFICATIONS MODEL CIRCUIT CRA04P 03 POWER RATING P70 °C W LIMITING ELEMENT VOLTAGE MAX V≅ 0.063 50 TEMPERATURE COEFFICIENT ppm/K TOLERANCE % RESISTANCE RANGE Ω E-SERIES ± 100 ±2 10R - 1M0 24 ± 200 ±5 1R0 - 1M0 24 Zero-Ohm-Resistor: Rmax = 50 mΩ, Imax = 1 A TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70 °C2) UNIT CRA04P W per element 0.063 Limiting Element Voltage1) V≅ 50 Insulation Voltage (1 min) Vdc/ac peak 100 Category Temperature Range °C - 55/+ 125 (+ 155) Insulation Resistance Ω > 109 Notes 1. Rated voltage: P × R 2. The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded. PART NUMBER AND PRODUCT DESPRIPTION PART NUMBER: CRA04P08347K0JTD1) C R A 0 4 P 0 8 3 4 7 K 0 J T D MODEL TERMINAL STYLE PIN CIRCUIT VALUE TOLERANCE PACKAGING2) SPECIAL CRA04 P 08 3 = 03 R = Decimal K = Thousand M = Million 0000 = 0 Ω Jumper G=±2% J=±5% Z = 0 Ω Jumper TD TC PZ up to 2 digits PRODUCT DESCRIPTION: CRA04P 08 03 473 J RT7 e3 CRA04P 08 03 473 J RT7 e3 LEAD (Pb)-FREE e3 = Pure Tin Termination Finish MODEL TERMINAL COUNT CIRCUIT TYPE RESISTANCE VALUE TOLERANCE PACKAGING2) CRA04P 08 03 473 = 47 kΩ 4R7 = 4.7 Ω 100 = 10 Ω 000 = 0 Ω Jumper First two digits (3 for 1 %) are significant. Last digit is the multiplier. G=±2% J=±5% Z = 0 Ω Jumper RT7 RT6 PZ Notes 1. Preferred way for ordering products is by use of the PART NUMBER. 2. Please refer to the table PACKAGING, see next page. Document Number: 31048 Revision: 09-Jan-07 For Technical Questions contact: [email protected] www.vishay.com 1 CRA04P Thick Film, Resistor Array Vishay PACKAGING PACKING CODE MODEL TAPE WIDTH CRA04P 8 mm DIAMETER PITCH PIECES/REEL PAPER TAPE PART NUMBER PRODUCT DESCRIPTION 180 mm/7" 2 mm 10 000 TD RT7 330 mm/13" 2 mm 20 000 TC RT6 330 mm/13" 2 mm 50 000 PZ PZ CIRCUIT Rated Power in % 03 Circuit 120 100 80 60 40 20 0 - 55 - 25 0 25 50 Derating 100 125 150 175 75 70 Ambient Temperature in °C DIMENSIONS A DIMENSIONS [in millimeters] C PIN NO# L A B C PNOM T W 8 2.00 0.20 0.32 0.25 0.50 0.35 1.00 TOL ± 0.10 ± 0.10 ± 0.10 ± 0.10 - ± 0.10 ± 0.10 W P B T L SOLDER PAD DIMENSIONS [in millimeters] c w b WAVE p www.vishay.com 2 c w p a b 0.5 1.5 0.5 0.32 0.5 a For Technical Questions contact: [email protected] Document Number: 31048 Revision: 09-Jan-07 CRA04P Thick Film, Resistor Array Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 REQUIREMENTS PERMISSIBLE CHANGE (ΔR/R)1) TEST (clause) CONDITIONS OF TEST STABILITY CLASS 2 OR BETTER stability for product types: 10 Ω to 1 MΩ 1 Ω to 1 MΩ ±2% ±5% ± 100 ppm/K ± 200 ppm/K CRA04P Resistance (4.5) - Temperature coefficient (4.8.4.2) 20/- 55/20 °C and 20/125/20 °C Overload (4.13) U = 2.5 × (P70 x R)1/2 ≤ 2 x Umax; 0.5 s Solderability (4.17.5)2) Aging 4 h at 155 °C, dryheat Solder bath method; 235 °C; 2 s Visual examination Resistance to soldering heat (4.18.2) Solder bath method; (260 ± 5) °C; (10 ± 1) s ± (0.5 % R + 0.05 Ω) Rapid change of temperature (4.19) 30 min. at LCT = - 55 °C; 30 min. at UCT = 125 °C; 5 cycles ± (0.5 % R + 0.05 Ω) Damp heat, steady state (4.24) (40 ± 2) °C; 56 days; (93 ± 3) % RH ± (2 % R + 0.1 Ω) Climatic sequence (4.23) 16 h at UCT = 125 °C; 1 cycle at 55 °C; 2 h at LCT = - 55 °C; 1 h/1 kPa at 15 °C to 35 °C; 5 cycles at 55 °C U = (P70 x R)1/2 U = Umax; whichever is less severe ± (2 % R + 0.1 Ω) Endurance at 70 °C (4.25.1) U = (P70 x R)1/2 U = Umax; whichever is less severe 1.5 h on; 0.5 h off; 70 °C; 1000 h ± (2 % R + 0.1 Ω) Extended endurance (4.25.1.8) Duration extended to 8000 hours ± (4 % R + 0.1 Ω) Endurance at upper category temperature (4.25.3) UCT = 125 °C; 1000 h ± (2 % R + 0.1 Ω) ± (0.5 % R + 0.05 Ω) Good tinning (≥ 95 % covered) no visible damage Notes 1. Figures are given for a single element. 2. Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years. APPLICABLE SPECIFICATIONS • EN 60115-1 Generic Specification • EN 140400 Sectional Specification • EN 140401-802 Detail Specification • IEC 60068-2-X Variety of environmental test procedures • EIA 481 Packaging of SMD components Document Number: 31048 Revision: 09-Jan-07 For Technical Questions contact: [email protected] www.vishay.com 3 Legal Disclaimer Notice Vishay Notice Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale. Document Number: 91000 Revision: 08-Apr-05 www.vishay.com 1