Catalyst CAT28LV64P-15T 64k-bit cmos parallel eeprom Datasheet

H
CAT28LV64
EE
GEN FR
ALO
64K-Bit CMOS PARALLEL EEPROM
LE
A D F R E ETM
FEATURES
■ 3.0V to 3.6 V Supply
■ CMOS and TTL compatible I/O
■ Read access times:
■ Automatic page write operation:
– 1 to 32 bytes in 5ms
– Page load timer
– 150/200/250ns
■ Low power CMOS dissipation:
■ End of write detection:
– Active: 8 mA max.
– Standby: 100 µA max.
– Toggle bit
– DATA polling
■ Simple write operation:
■ Hardware and software write protection
– On-chip address and data latches
– Self-timed write cycle with auto-clear
■ 100,000 program/erase cycles
■ Fast write cycle time:
■ 100 year data retention
– 5ms max.
■ Commercial, industrial and automotive
temperature ranges
DESCRIPTION
The CAT28LV64 is a low voltage, low power, CMOS
parallel EEPROM organized as 8K x 8-bits. It requires a
simple interface for in-system programming. On-chip
address and data latches, self-timed write cycle with autoclear and VCC power up/down write protection eliminate
additional timing and protection hardware. DATA Polling
and Toggle status bit signal the start and end of the selftimed write cycle. Additionally, the CAT28LV64 features
hardware and software write protection.
The CAT28LV64 is manufactured using Catalyst’s
advanced CMOS floating gate technology. It is designed
to endure 100,000 program/erase cycles and has a data
retention of 100 years. The device is available in JEDEC
approved 28-pin DIP, 28-pin TSOP, 28-pin SOIC or 32pin PLCC packages.
BLOCK DIAGRAM
A5–A12
ADDR. BUFFER
& LATCHES
ROW
DECODER
VCC
INADVERTENT
WRITE
PROTECTION
HIGH VOLTAGE
GENERATOR
CE
OE
WE
CONTROL
LOGIC
32 BYTE PAGE
REGISTER
I/O BUFFERS
TIMER
A0–A4
8,192 x 8
E2PROM
ARRAY
DATA POLLING
AND
TOGGLE BIT
ADDR. BUFFER
& LATCHES
© 2004 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
I/O0–I/O7
COLUMN
DECODER
1
Doc. No. 1010, Rev. D
CAT28LV64
PIN CONFIGURATION
DIP Package (P, L)
NC
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SOIC Package (J, W) (K, X)
28
27
26
25
24
23
22
21
20
19
18
17
VCC
WE
NC
A8
A9
A11
OE
16
15
I/O4
I/O3
A10
CE
I/O7
I/O6
I/O5
4 3 2 1 32 31 30
A6
A5
5
6
29
28
A8
A4
A3
A2
7
8
9
10
27
26
25
24
A11
11
23
12
22
13
21
14 15 16 17 18 19 20
I/O1
I/O2
VSS
NC
A0
NC
I/O0
28
VCC
2
3
4
27
26
25
WE
NC
A8
A5
A4
A3
5
6
7
24
23
22
A9
A11
OE
A2
A1
A0
I/O0
8
9
10
11
21
20
19
18
A10
CE
I/O7
I/O1
I/O2
VSS
12
13
14
17
I/O6
I/O5
16
15
I/O4
I/O3
A9
NC
OE
A10
CE
I/O7
OE
A11
A9
A8
NC
WE
VCC
NC
A12
A7
A6
A5
A4
A3
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
I/O6
I/O3
I/O4
I/O5
A1
TOP VIEW
1
TSOP Top View (8mm x 13.4mm) (T13, H13)
WE
NC
A7
A12
NC
NC
VCC
PLCC Package (N, G)
NC
A12
A7
A6
PIN FUNCTIONS
Pin Name
Function
Pin Name
Function
A0–A12
Address Inputs
WE
Write Enable
I/O0–I/O7
Data Inputs/Outputs
VCC
3.0 to 3.6 V Supply
CE
Chip Enable
VSS
Ground
OE
Output Enable
NC
No Connect
Doc. No. 1010, Rev. D
2
A10
CE
I/O7
I/O6
I/O5
I/O4
I/O3
GND
I/O2
I/O1
I/O0
A0
A1
A2
CAT28LV64
ABSOLUTE MAXIMUM RATINGS*
*COMMENT
Temperature Under Bias ................. –55°C to +125°C
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation
of the device at these or any other conditions outside of
those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum
rating for extended periods may affect device performance and reliability.
Storage Temperature ....................... –65°C to +150°C
Voltage on Any Pin with
Respect to Ground(2) ........... –2.0V to +VCC + 2.0V
VCC with Respect to Ground ............... –2.0V to +7.0V
Package Power Dissipation
Capability (Ta = 25°C) ................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current(3) ........................ 100 mA
RELIABILITY CHARACTERISTICS
Symbol
Units
Test Method
Endurance
105
Cycles/Byte
MIL-STD-883, Test Method 1033
Data Retention
100
Years
MIL-STD-883, Test Method 1008
VZAP
ESD Susceptibility
2000
Volts
MIL-STD-883, Test Method 3015
ILTH(1)(4)
Latch-Up
100
mA
NEND
(1)
TDR(1)
(1)
Parameter
Min.
Max.
JEDEC Standard 17
MODE SELECTION
CE
WE
OE
Read
L
H
Byte Write (WE Controlled)
L
Mode
Byte Write (CE Controlled)
I/O
Power
L
DOUT
ACTIVE
H
DIN
ACTIVE
L
H
DIN
ACTIVE
Standby, and Write Inhibit
H
X
X
High-Z
STANDBY
Read and Write Inhibit
X
H
H
High-Z
ACTIVE
Test
Max.
Units
Conditions
Input/Output Capacitance
10
pF
VI/O = 0V
Input Capacitance
6
pF
VIN = 0V
CAPACITANCE TA = 25°C, f = 1.0 MHz
Symbol
CI/O
(1)
CIN(1)
Note:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns.
(3) Output shorted for no more than one second. No more than one output shorted at a time.
(4) Latch-up protection is provided for stresses up to 100mA on address and data pins from –1V to VCC +1V.
3
Doc. No. 1010, Rev. D
CAT28LV64
D.C. OPERATING CHARACTERISTICS
Vcc = 3.0V to 3.6V, unless otherwise specified.
Limits
Symbol
Parameter
Min.
Typ.
Max.
Units
Test Conditions
ICC
VCC Current (Operating, TTL)
8
mA
CE = OE = VIL,
f = 1/tRC min, All I/O’s Open
ISBC(3)
VCC Current (Standby, CMOS)
100
µA
CE = VIHC,
All I/O’s Open
ILI
Input Leakage Current
–1
1
µA
VIN = GND to VCC
ILO
Output Leakage Current
–5
5
µA
VOUT = GND to VCC,
CE = VIH
VIH(3)
High Level Input Voltage
2
VCC +0.3
V
VIL
Low Level Input Voltage
–0.3
0.6
V
VOH
High Level Output Voltage
VOL
Low Level Output Voltage
VWI
Write Inhibit Voltage
2
0.3
2
V
IOH = –100µA
V
IOL = 1.0mA
V
A.C. CHARACTERISTICS, Read Cycle
Vcc = 3.0V to 3.6V, unless otherwise specified.
28LV64-15
Min.
28LV64-25
Symbol
Parameter
Min.
tRC
Read Cycle Time
150
tCE
CE Access Time
150
200
250
ns
tAA
Address Access Time
150
200
250
ns
tOE
OEAccess Time
70
80
100
ns
tLZ(1)
CE Low to Active Output
0
0
tOLZ(1)
OE Low to Active Output
0
0
tHZ(1)(2)
CE High to High-Z Output
50
50
55
ns
tOHZ(1)(2)
OE High to High-Z Output
50
50
55
ns
tOH(1)
Output Hold from
Address Change
0
Max.
28LV64-20
Max.
Min.
200
0
250
4
Units
ns
0
ns
0
ns
0
Note:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) Output floating (High-Z) is defined as the state when the external data line is no longer driven by the output buffer.
(3) VIHC = VCC –0.3V to VCC +0.3V.
Doc. No. 1010, Rev. D
Max.
ns
CAT28LV64
Figure 1. A.C. Testing Input/Output Waveform(4)
VCC - 0.3 V
2.0 V
INPUT PULSE LEVELS
REFERENCE POINTS
0.6 V
0.0 V
Figure 2. A.C. Testing Load Circuit (example)
Vcc
1.8 K
DEVICE
UNDER
TEST
OUTPUT
CL= 100 pF
1. 3K
CL INCLUDES JIG CAPACITANCE
A.C. CHARACTERISTICS, Write Cycle
Vcc = 3.0V to 3.6V, unless otherwise specified.
28LV64-15
Symbol
Parameter
tWC
Write Cycle Time
tAS
Address Setup Time0
tAH
Address Hold Time
tCS
Min
Max
28LV64-20
Min
5
Max
28LV64-25
Min
5
Max
Units
5
ms
0
0
0
ns
100
100
100
ns
CE Setup Time
0
0
0
ns
tCH
CE Hold Time
0
0
0
ns
tCW(2)
CE Pulse Time
110
150
150
ns
tOES
OE Setup Time
0
10
10
ns
tOEH
OE Hold Time
0
10
10
ns
tWP(2)
WE Pulse Width
110
150
150
ns
tDS
Data Setup Time
60
100
100
ns
tDH
Data Hold Time
0
0
0
ns
Write Inhibit Period
After Power-up
5
10
5
10
5
10
ms
0.05
100
0.1
100
0.1
100
µs
tINIT(1)
tBLC(1)(3)
Byte Load Cycle Time
Note:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) A write pulse of less than 20ns duration will not initiate a write cycle.
(3) A timer of duration tBLC max. begins with every LOW to HIGH transition of WE. If allowed to time out, a page or byte write will begin;
however a transition from HIGH to LOW within tBLC max. stops the timer.
(4) Input rise and fall times (10% and 90%) < 10 ns.
5
Doc. No. 1010, Rev. D
CAT28LV64
Byte Write
DEVICE OPERATION
A write cycle is executed when both CE and WE are low,
and OE is high. Write cycles can be initiated using either
WE or CE, with the address input being latched on the
falling edge of WE or CE, whichever occurs last. Data,
conversely, is latched on the rising edge of WE or CE,
whichever occurs first. Once initiated, a byte write cycle
automatically erases the addressed byte and the new
data is written within 5 ms.
Read
Data stored in the CAT28LV64 is transferred to the data
bus when WE is held high, and both OE and CE are held
low. The data bus is set to a high impedance state when
either CE or OE goes high. This 2-line control architecture
can be used to eliminate bus contention in a system
environment.
Figure 3. Read Cycle
tRC
ADDRESS
tCE
CE
tOE
OE
VIH
tLZ
WE
tOHZ
DATA OUT
tHZ
tOH
tOLZ
HIGH-Z
DATA VALID
DATA VALID
tAA
Figure 4. Byte Write Cycle [WE Controlled]
tWC
ADDRESS
tAS
tAH
tCH
tCS
CE
OE
tOES
tWP
tOEH
WE
tBLC
DATA OUT
DATA IN
HIGH-Z
DATA VALID
tDS
Doc. No. 1010, Rev. D
Doc. No. 1010, Rev. A
tDH
6
CAT28LV64
Page Write
(which can be loaded in any order) during the first and
subsequent write cycles. Each successive byte load
cycle must begin within tBLC MAX of the rising edge of the
preceding WE pulse. There is no page write window
limitation as long as WE is pulsed low within tBLC MAX.
The page write mode of the CAT28LV64 (essentially an
extended BYTE WRITE mode) allows from 1 to 32 bytes
of data to be programmed within a single EEPROM write
cycle. This effectively reduces the byte-write time by a
factor of 32.
Upon completion of the page write sequence, WE must
stay high a minimum of tBLC MAX for the internal automatic
program cycle to commence. This programming cycle
consists of an erase cycle, which erases any data that
existed in each addressed cell, and a write cycle, which
writes new data back into the cell. A page write will only
write data to the locations that were addressed and will
not rewrite the entire page.
Following an initial WRITE operation (WE pulsed low, for
tWP, and then high) the page write mode can begin by
issuing sequential WE pulses, which load the address
and data bytes into a 32 byte temporary buffer. The page
address where data is to be written, specified by bits A5
to A12, is latched on the last falling edge of WE. Each
byte within the page is defined by address bits A0 to A4
Figure 5. Byte Write Cycle [CE Controlled]
tWC
ADDRESS
tAS
tAH
tBLC
tCW
CE
tOEH
OE
tCS
tOES
tCH
WE
HIGH-Z
DATA OUT
DATA IN
DATA VALID
tDS
tDH
Figure 6. Page Mode Write Cycle
OE
CE
t WP
t BLC
WE
ADDRESS
t WC
I/O
LAST BYTE
BYTE 0
BYTE 1
BYTE 2
7
BYTE n
BYTE n+1
BYTE n+2
Doc. No. 1010, Rev. D
Doc. No. 1010, Rev. A
CAT28LV64
DATA Polling
Toggle Bit
DATA polling is provided to indicate the completion of
write cycle. Once a byte write or page write cycle is
initiated, attempting to read the last byte written will
output the complement of that data on I/O7 (I/O0–I/O6
are indeterminate) until the programming cycle is
complete. Upon completion of the self-timed write cycle,
all I/O’s will output true data during a read cycle.
In addition to the DATA Polling feature, the device offers
an additional method for determining the completion of
a write cycle. While a write cycle is in progress, reading
data from the device will result in I/O6 toggling between
one and zero. However, once the write is complete, I/O6
stops toggling and valid data can be read from the
device.
Figure 7. DATA Polling
ADDRESS
CE
WE
tOEH
tOES
tOE
OE
tWC
I/O7
DIN = X
DOUT = X
DOUT = X
Figure 8. Toggle Bit
WE
CE
tOEH
tOES
tOE
OE
I/O6
(1)
(1)
tWC
Note:
(1) Beginning and ending state of I/O6 is indeterminate.
Doc. No. 1010, Rev. D
8
CAT28LV64
HARDWARE DATA PROTECTION
(4) Noise pulses of less than 20 ns on the WE or CE
inputs will not result in a write cycle.
The following is a list of hardware data protection features
that are incorporated into the CAT28LV64.
SOFTWARE DATA PROTECTION
(1) VCC sense provides for write protection when VCC
falls below 2.0V min.
The CAT28LV64 features a software controlled data
protection scheme which, once enabled, requires a data
algorithm to be issued to the device before a write can be
performed. The device is shipped from Catalyst with the
software protection NOT ENABLED (the CAT28LV64 is
in the standard operating mode).
(2) A power on delay mechanism, tINIT (see AC
characteristics), provides a 5 to 10 ms delay before
a write sequence, after VCC has reached 2.40V min.
(3) Write inhibit is activated by holding any one of OE
low, CE high or WE high.
Figure 9. Write Sequence for Activating Software
Data Protection
WRITE DATA:
ADDRESS:
WRITE DATA:
ADDRESS:
WRITE DATA:
ADDRESS:
Figure 10. Write Sequence for Deactivating
Software Data Protection
WRITE DATA:
AA
ADDRESS:
1555
WRITE DATA:
55
ADDRESS:
0AAA
WRITE DATA:
A0
ADDRESS:
1555
WRITE DATA:
SOFTWARE DATA
(1)
PROTECTION ACTIVATED
WRITE DATA:
ADDRESS:
WRITE DATA:
XX
ADDRESS:
TO ANY ADDRESS
WRITE DATA:
WRITE LAST BYTE
TO
LAST ADDRESS
ADDRESS:
AA
1555
55
0AAA
80
1555
AA
1555
55
0AAA
20
1555
28LV64 F12
Note:
(1) Write protection is activated at this point whether or not any more writes are completed. Writing to addresses must occur within tBLC
Max., after SDP activation.
9
Doc. No. 1010, Rev. D
CAT28LV64
To activate the software data protection, the device must
be sent three write commands to specific addresses with
specific data (Figure 9). This sequence of commands
(along with subsequent writes) must adhere to the page
write timing specifications (Figure 11). Once this is done,
all subsequent byte or page writes to the device must be
preceded by this same set of write commands. The data
protection mechanism is activated until a deactivate
sequence is issued regardless of power on/off transitions.
This gives the user added inadvertent write protection
on power-up in addition to the hardware protection
provided.
To allow the user the ability to program the device with
an EEPROM programmer (or for testing purposes) there
is a software command sequence for deactivating the
data protection. The six step algorithm (Figure 10) will
reset the internal protection circuitry, and the device will
return to standard operating mode (Figure 12 provides
reset timing). After the sixth byte of this reset sequence
has been issued, standard byte or page writing can
commence.
Figure 11. Software Data Protection Timing
DATA
ADDRESS
AA
1555
55
0AAA
tWC
A0
1555
CE
tWP
tBLC
BYTE OR
PAGE
WRITES
ENABLED
WE
Figure 12. Resetting Software Data Protection Timing
DATA
ADDRESS
AA
1555
55
0AAA
80
1555
AA
1555
55
0AAA
20
1555
tWC
SDP
RESET
CE
DEVICE
UNPROTECTED
WE
Doc. No. 1010, Rev. D
10
CAT28LV64
ORDERING INFORMATION
Prefix
Device #
CAT
28LV64
Optional
Company
ID
Product
Number
Suffix
N
I
Temperature Range
Blank = Commercial (0°C to +70°C)
I = Industrial (-40°C to +85°C)
A = Automotive (-40°C to +105°C)*
Package
P: PDIP
J: SOIC (JEDEC)
K: SOIC (EIAJ)
N: PLCC
T13: TSOP (8mmx13.4mm)
L: PDIP (Lead free, Halogen free)
W: SOIC (JEDEC) (Lead free, Halogen free)
X: SOIC (EIAJ) (Lead free, Halogen free)
G: PLCC (Lead free, Halogen free)
H13: TSOP (8mmx13.4mm) (Lead free, Halogen free)
T
-25
Tape & Reel
Speed
15: 150ns
20: 200ns
25: 250ns
* -40°C to +125°C is available upon request
Notes:
(1) The device used in the above example is a CAT28LV64NI-25T (PLCC, Industrial temperature, 250 ns Access Time, Tape & Reel).
11
Doc. No. 1010, Rev. D
REVISION HISTORY
Date
Revision Comments
3/29/04
C
04/20/04
D
Added Green packages in all areas
Delete data sheet designation
Update Ordering Information
Update Revision History
Update Rev Number
Copyrights, Trademarks and Patents
Trademarks and registered trademarks of Catalyst Semiconductor include each of the following:
DPP ™
AE2 ™
Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents
issued to Catalyst Semiconductor contact the Company’s corporate office at 408.542.1000.
CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS
PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE
RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING
OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or
other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a
situation where personal injury or death may occur.
Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets
labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale.
Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate
typical semiconductor applications and may not be complete.
Catalyst Semiconductor, Inc.
Corporate Headquarters
1250 Borregas Avenue
Sunnyvale, CA 94089
Phone: 408.542.1000
Fax: 408.542.1200
www.catalyst-semiconductor.com
Publication #:
Revison:
Issue date:
1010
D
04/20/04
Similar pages