Features • • • • • • • • • • Single-voltage Read/Write Operation: 2.7V to 3.6V (BV), 3.0V to 3.6V (LV) Fast Read Access Time – 70 ns Internal Erase/Program Control Sector Architecture – One 8K Word (16K Bytes) Boot Block with Programming Lockout – Two 4K Word (8K Bytes) Parameter Blocks – One 112K Word (224K Bytes) Main Memory Array Block Fast Sector Erase Time – 10 Seconds Byte-by-byte or Word-by-word Programming – 30 µs Typical Hardware Data Protection Data Polling for End of Program Detection Low Power Dissipation – 25 mA Active Current – 50 µA CMOS Standby Current Typical 10,000 Write Cycles Description The AT49BV/LV2048A is a 3-volt, 2-megabit Flash memory organized as 262,144 words of 8 bits each or 128K words of 16 bits each. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers access times to 70 ns with power dissipation of just 67 mW at 2.7V read. When deselected, the CMOS standby current is less than 50 µA. Th e device co nt ain s a us e r-e n a ble d “ bo o t blo ck ” pr ot ec tio n fe a tu re. Th e AT49BV/LV2048A locates the boot block at lowest order addresses (“bottom boot”). To allow for simple in-system reprogrammability, the AT49BV/LV2048A does not require high input voltages for programming. Reading data out of the device is similar to reading from an EPROM; it has standard CE, OE and WE inputs to avoid bus contention. Reprogramming the AT49BV/LV2048A is performed by first erasing a block of data and then programming on a byte-by-byte or word-by-word basis. 2-megabit (256K x 8/ 128K x 16) Single 2.7-volt Battery-Voltage™ Flash Memory AT49BV2048A AT49LV2048A Pin Configurations Pin Name Function A0 - A16 Addresses CE Chip Enable OE Output Enable WE Write Enable RESET Reset VPP VPP can be left unconnected or connected to VCC, GND, 5V or 12V. The input has no effect on the operation of the device. I/O0 - I/O15 Data Inputs/Outputs I/O15(A-1) I/O15 (Data Input/Output, Word Mode) A-1 (LSB Address Input, Byte Mode) BYTE Selects Byte or Word Mode NC No Connect Rev. 1914D–FLASH–03/02 1 AT49BV/LV2048A SOIC (SOP) VPP NC NC A7 A6 A5 A4 A3 A2 A1 A0 CE GND OE I/O0 I/O8 I/O1 I/O9 I/O2 I/O10 I/O3 I/O11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 AT49BV/LV2048A TSOP Top View Type 1 RESET WE A8 A9 A10 A11 A12 A13 A14 A15 A16 BYTE GND I/O15/A-1 I/O7 I/O14 I/O6 I/O13 I/O5 I/O12 I/O4 VCC A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE RESET VPP NC NC NC NC A7 A6 A5 A4 A3 A2 A1 Note: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A16 BYTE GND I/O15/A-1 I/O7 I/O14 I/O6 I/O13 I/O5 I/O12 I/O4 VCC I/O11 I/O3 I/O10 I/O2 I/O9 I/O1 I/O8 I/O0 OE GND CE A0 “•” denotes a white dot on the package. The device is erased by executing the Erase command sequence; the device internally controls the erase operation. The memory is divided into four blocks for erase operations. There are two 4K word parameter block sections, the boot block, and the main memory array block. The typical number of program and erase cycles is in excess of 10,000 cycles. The 8K word boot block section includes a reprogramming lock out feature to provide data integrity. This feature is enabled by a command sequence. Once the boot block programming lockout feature is enabled, the data in the boot block cannot be changed when input levels of 5.5 volts or less are used. The boot sector is designed to contain user secure code. The BYTE pin controls whether the device data I/O pins operate in the byte or word configuration. If the BYTE pin is set at a logic “1” or left open, the device is in word configuration, I/O0 I/O15 are active and controlled by CE and OE. If the BYTE pin is set at logic “0”, the device is in byte configuration, and only data I/O pins I/O0 - I/O7 are active and controlled by CE and OE. The data I/O pins I/O8 - I/O14 are tristated and the I/O15 pin is used as an input for the LSB (A-1) address function. 2 AT49BV/LV2048A 1914D–FLASH–03/02 AT49BV/LV2048A AT49BV/LV2048 A Block Diagram VCC DATA INPUTS/OUTPUTS I/O0 - I/O15 GND OE WE CE RESET CONTROL LOGIC Y DECODER ADDRESS INPUTS X DECODER INPUT/OUTPUT BUFFERS PROGRAM DATA LATCHES Y-GATING MAIN MEMORY (112K WORDS) PARAMETER BLOCK 2 4K WORDS PARAMETER BLOCK 1 4K WORDS BOOT BLOCK 8K WORDS Device Operation 1FFFF 04000 03FFF 03000 02FFF 02000 01FFF 00000 READ: The AT49BV/LV2048A is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high-impedance state whenever CE or OE is high. This dual-line control gives designers flexibility in preventing bus contention. COMMAND SEQUENCES: When the device is first powered on it will be reset to the read or standby mode, depending upon the state of the control line inputs. In order to perform other device functions, a series of command sequences are entered into the device. The command sequences are shown in the Command Definitions table (I/O8 - I/O15 are don’t care inputs for the command codes). The command sequences are written by applying a low pulse on the WE or CE input with CE or WE low (respectively) and OE high. The address is latched on the falling edge of CE or WE, whichever occurs last. The data is latched by the first rising edge of CE or WE. Standard microprocessor write timings are used. The address locations used in the command sequences are not affected by entering the command sequences. RESET: A RESET input pin is provided to ease some system applications. When RESET is at a logic high level, the device is in its standard operating mode. A low level on the RESET input halts the present device operation and puts the outputs of the device in a high-impedance state. When a high level is reasserted on the RESET pin, the device returns to the read or standby mode, depending upon the state of the control inputs. By applying a 12V <Symbol 10pt>± 0.5V input signal to the RESET pin the boot block array can be reprogrammed even if the boot block program lockout feature has been enabled (see “Boot Block Programming Lockout Override” section). ERASURE: Before a byte or word can be reprogrammed, it must be erased. The erased state of memory bits is a logic “1”. The entire device can be erased by using the Chip Erase command or individual sectors can be erased by using the Sector Erase commands. CHIP ERASE: The entire device can be erased at one time by using the 6-byte chip erase software code. After the chip erase has been initiated, the device will internally time the erase operation so that no external clocks are required. The maximum time to erase the chip is tEC. If the boot block lockout has been enabled, the chip erase will not erase the data in the boot block; it will erase the main memory block and the parameter blocks only. After the chip erase, the device will return to the read or standby mode. 3 1914D–FLASH–03/02 SECTOR ERASE: As an alternative to a full chip erase, the device is organized into four sectors that can be individually erased. There are two 4K word parameter block sections, one boot block, and the main memory array block. The Sector Erase command is a six-bus cycle operation. The sector address is latched on the falling WE edge of the sixth cycle while the 30H data input command is latched at the rising edge of WE. The sector erase starts after the rising edge of WE of the sixth cycle. The erase operation is internally controlled; it will automatically time to completion. Whenever the main memory block is erased and reprogrammed, the two parameter blocks should be erased and reprogrammed before the main memory block is erased again. Whenever a parameter block is erased and reprogrammed, the other parameter block should be erased and reprogrammed before the first parameter block is erased again. Whenever the boot block is erased and reprogrammed, the main memory block and the parameter blocks should be erased and reprogrammed before the boot block is erased again. BYTE/WORD PROGRAMMING: Once a memory block is erased, it is programmed (to a logic “0”) on a byte-by-byte or word-by-word basis. Programming is accomplished via the internal device command register and is a four-bus cycle operation. The device will automatically generate the required internal program pulses. Any commands written to the chip during the embedded programming cycle will be ignored. If a hardware reset happens during programming, the data at the location being programmed will be corrupted. Please note that a data “0” cannot be programmed back to a “1”; only erase operations can convert “0”s to “1”s. Programming is completed after the specified tBP cycle time. The Data Polling feature may also be used to indicate the end of a program cycle. BOOT BLOCK PROGRAMMING LOCKOUT: The device has one designated block that has a programming lockout feature. This feature prevents programming of data in the designated block once the feature has been enabled. The size of the block is 8K words. This block, referred to as the boot block, can contain secure code that is used to bring up the system. Enabling the lockout feature will allow the boot code to stay in the device while data in the rest of the device is updated. This feature does not have to be activated; the boot block’s usage as a write-protected region is optional to the user. The address range of the boot block is 00000H to 01FFFH. Once the feature is enabled, the data in the boot block can no longer be erased or programmed when input levels of 5.5V or less are used. Data in the main memory block can still be changed through the regular programming method. To activate the lockout feature, a series of six program commands to specific addresses with specific data must be performed. Please refer to the Command Definitions table. BOOT BLOCK LOCKOUT DETECTION: A software method is available to determine if programming of the boot block section is locked out. When the device is in the software product identification mode (see Software Product Identification Entry and Exit sections) a read from the following address location will show if programming the boot block is locked out – 00002H. If the data on I/O0 is low, the boot block can be programmed; if the data on I/O0 is high, the program lockout feature has been enabled and the block cannot be programmed. The software product identification exit code should be used to return to standard operation. BOOT BLOCK PROGRAMMING LOCKOUT OVERRIDE: The user can override the boot block programming lockout by taking the RESET pin to 12 volts during the entire chip erase, sector erase or word programming operation. When the RESET pin is brought back to TTL levels the boot block programming lockout feature is again active. 4 AT49BV/LV2048A 1914D–FLASH–03/02 AT49BV/LV2048A PRODUCT IDENTIFICATION: The product identification mode identifies the device and manufacturer as Atmel. It may be accessed by hardware or software operation. The hardware operation mode can be used by an external programmer to identify the correct programming algorithm for the Atmel product. For details, see “Operating Modes” (for hardware operation) or “Software Product Identification Entry/Exit” on page 13. The manufacturer and device codes are the same for both modes. DATA POLLING: The AT49BV/LV2048A features Data Polling to indicate the end of a program cycle. During a program cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all outputs and the next cycle may begin. During a chip or sector erase operation, an attempt to read the device will give a “0” on I/O7. Once the program or erase cycle has completed, true data will be read from the device. Data Polling may begin at any time during the program cycle. TOGGLE BIT: In addition to Data Polling, the AT49BV/LV2048A provides another method for determining the end of a program or erase cycle. During a program or erase operation, successive attempts to read data from the device will result in I/O6 toggling between one and zero. Once the program cycle has completed, I/O6 will stop toggling and valid data will be read. Examining the toggle bit may begin at any time during a program cycle. HARDWARE DATA PROTECTION: Hardware features protect against inadvertent programs to the AT49BV/LV2048A in the following ways: (a) VCC sense: if VCC is below 1.8V (typical), the program function is inhibited. (b) V CC power on delay: once V CC has reached the V CC sense level, the device will automatically time out 10 ms (typical) before programming. (c) Program inhibit: holding any one of OE low, CE high or WE high inhibits program cycles. (d) Noise filter: pulses of less than 15 ns (typical) on the WE or CE inputs will not initiate a program cycle. INPUT LEVELS: While operating with a 2.7V to 3.6V power supply, the address and control inputs (OE, CE and WE) may be driven from 0 to 5.5V without adversely affecting the operation of the device. The I/O lines can only be driven from 0 to VCC + 0.6V. 5 1914D–FLASH–03/02 Command Definition (in Hex)(1) Command Sequence 1st Bus Cycle Bus Cycles Addr Data Read 1 Addr DOUT Chip Erase 6 5555 AA 2nd Bus Cycle 3rd Bus Cycle 4th Bus Cycle 6th Bus Cycle Addr Data Addr Data Addr Data Addr Data Addr Data 2AAA 55 5555 80 5555 AA 2AAA 55 5555 10 2AAA 55 (4) SA 30 2AAA 55 5555 40 Sector Erase 6 5555 AA 2AAA 55 5555 80 5555 AA Byte/Word Program 4 5555 AA 2AAA 55 5555 A0 Addr DIN Boot Block Lockout(2) 6 5555 AA 2AAA 55 5555 80 5555 AA Product ID Entry 3 5555 AA 2AAA 55 5555 90 Product ID Exit (3) 3 5555 AA 2AAA 55 5555 F0 Product ID Exit (3) 1 xxxx F0 Notes: 5th Bus Cycle 1. The DATA FORMAT in each bus cycle is as follows: I/O15 - I/O8 (Don’t Care); I/O7 - I/O0 (Hex). The ADDRESS FORMAT in each bus cycle is as follows: A15 - A0 (Hex), A-1, and A15 - A16 (Don’t Care). 2. The boot sector has the address range 00000H to 01FFFH. 3. Either one of the Product ID Exit commands can be used. 4. SA = sector addresses: (A16 - A0) SA = 01XXX for BOOT BLOCK SA = 02XXX for PARAMETER BLOCK 1 SA = 03XXX for PARAMETER BLOCK 2 SA = 1FXXX for MAIN MEMORY ARRAY Absolute Maximum Ratings* Temperature under Bias ................................ -55°C to +125°C Storage Temperature ..................................... -65°C to +150°C All Input Voltages (including NC Pins) with Respect to Ground ...................................-0.6V to +6.25V All Output Voltages with Respect to Ground .............................-0.6V to VCC + 0.6V *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on RESET with Respect to Ground ...................................-0.6V to +13.5V 6 AT49BV/LV2048A 1914D–FLASH–03/02 AT49BV/LV2048A DC and AC Operating Range Operating Temperature (Case) AT49LV2048A-70 AT49BV2048A-90 AT49BV2048A-12 0°C - 70°C 0°C - 70°C 0°C - 70°C N/A -40°C - 85°C -40°C - 85°C 3.0V - 3.6V 2.7V - 3.6V 2.7V - 3.6V Com. Ind. VCC Power Supply Operating Modes Mode CE OE WE RESET Ai I/O VIL V IL VIH VIH Ai DOUT VIL VIH VIL VIH Ai DIN VIH X (1) X VIH X X X VIH VIH X V IL X VIH Output Disable X VIH X VIH Reset X X X VIL Read Program/Erase (2) Standby/Program Inhibit Program Inhibit High-Z High-Z X High-Z Product Identification Hardware VIL V IL VIH VIH Software(5) VIH Notes: A1 - A16 = VIL, A9 = VH(3) A0 = VIL Manufacturer Code(4) A1 - A16 = VIL, A9 = VH(3) A0 = VIH Device Code(4) A0 = VIL, A1 - A16 = VIL Manufacturer Code(4) A0 = VIH, A1 - A16 = VIL Device Code(4) 1. 2. 3. 4. X can be VIL or VIH. Refer to AC programming waveforms. VH = 12.0V <Symbol 10pt>± 0.5V. Manufacturer Code: 001FH Device Code: 0082H 5. See details under “Software Product Identification Entry/Exit” on page 13. DC Characteristics Symbol Parameter Condition ILI Input Load Current ILO Max Units VIN = 0V to VCC 10.0 µA Output Leakage Current VI/O = 0V to VCC 10.0 µA ISB1 VCC Standby Current CMOS CE = VCC - 0.3V to V CC 50.0 µA ISB2 VCC Standby Current TTL CE = 2.0V to VCC 0.5 mA VCC Active Current f = 5 MHz; IOUT = 0 mA 25.0 mA 0.6 V ICC (1) VIL Input Low Voltage VIH Input High Voltage VOL Output Low Voltage IOL = 2.1 mA Output High Voltage IOH = -400 µA VOH Note: Min 2.0 V 0.45 2.4 V V In the erase mode, ICC is 50 mA. 7 1914D–FLASH–03/02 AC Read Characteristics AT49LV2048A-70 AT49BV2048A-90 AT49BV2048A-12 Min Min Min Symbol Parameter Max Max Max Units tACC Address to Output Delay 70 90 120 ns tCE(1) CE to Output Delay 70 90 120 ns tOE(2) OE to Output Delay 0 35 0 40 0 50 ns tDF(3)(4) CE or OE to Output Float 0 25 0 25 0 30 ns tOH Output Hold from OE, CE or Address, whichever occurred first 0 tRO RESET to Output Delay 0 0 800 800 ns 800 ns AC Read Waveforms(1)(2)(3)(4) ADDRESS ADDRESS VALID CE t OE CE t OE t t RESET OUTPUT Notes: 8 DF t ACC OH t RO HIGH Z OUTPUT VALID 1. CE may be delayed up to tACC - tCE after the address transition without impact on tACC. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE or by tACC - tOE after an address change without impact on tACC. 3. tDF is specified from OE or CE, whichever occurs first (CL = 5 pF). 4. This parameter is characterized and is not 100% tested. AT49BV/LV2048A 1914D–FLASH–03/02 AT49BV/LV2048A Input Test Waveforms and Measurement Level 2.4V 0.4V tR, tF < 5 ns Output Test Load 3.3V 1.8K OUTPUT PIN 1.3K 100 pF Pin Capacitance f = 1 MHz, T = 25°C(1) Symbol Typ Max Units Conditions CIN 4 6 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: This parameter is characterized and is not 100% tested. 9 1914D–FLASH–03/02 AC Word Load Characteristics Symbol Parameter Min Max Units tAS, tOES Address, OE Setup Time 0 ns tAH Address Hold Time 70 ns tCS Chip Select Setup Time 0 ns tCH Chip Select Hold Time 0 ns tWP Write Pulse Width (WE or CE) 70 ns tDS Data Setup Time 70 ns tDH, tOEH Data, OE Hold Time 0 ns tWPH Write Pulse Width High 50 ns AC Byte/Word Load Waveforms WE Controlled CE Controlled 10 AT49BV/LV2048A 1914D–FLASH–03/02 AT49BV/LV2048A Program Cycle Characteristics Symbol Parameter Min Typ Max Units tBP Byte/Word Programming Time tAS Address Setup Time 0 ns tAH Address Hold Time 70 ns tDS Data Setup Time 70 ns tDH Data Hold Time 0 ns tWP Write Pulse Width 70 ns tWPH Write Pulse Width High 50 ns tEC Erase Cycle Time 30 µs 10 seconds Program Cycle Waveforms PROGRAM CYCLE OE CE t WP t BP t WPH WE t AS A0-A16 t DH t AH 5555 5555 2AAA 5555 ADDRESS t DS 55 AA DATA A0 AA INPUT DATA Sector or Chip Erase Cycle Waveforms OE (1) CE t WP t WPH WE t AS A0-A16 t DH t AH 5555 5555 2AAA 5555 Note 2 2AAA t EC t DS DATA AA WORD 0 Notes: 55 WORD 1 80 AA 55 Note 3 WORD 2 WORD 3 WORD 4 WORD 5 1. OE must be high only when WE and CE are both low. 2. For chip erase, the address should be 5555. For sector erase, the address depends on what sector is to be erased. (See note 4 under Command Definitions.) 3. For chip erase, the data should be 10H, and for sector erase, the data should be 30H. 11 1914D–FLASH–03/02 Data Polling Characteristics(1) Symbol Parameter Min tDH Data Hold Time tOEH OE Hold Time Max OE to Output Delay tWR Write Recovery Time Units 10 ns 10 ns (2) tOE Notes: Typ ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See tOE spec in “AC Read Characteristics” on page 8. Data Polling Waveforms WE CE tOEH OE tDH tOE I/O7 A0-A16 An tWR HIGH Z An An An An Toggle Bit Characteristics(1) Symbol Parameter tDH Data Hold Time tOEH OE Hold Time Min OE to Output Delay tOEHP OE High Pulse tWR Write Recovery Time Max Units 10 ns 10 ns (2) tOE Notes: Typ ns 150 ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See tOE spec in “AC Read Characteristics” on page 8. Toggle Bit Waveforms(1)(2)(3) WE CE tOEHP tOEH OE tDH I/O6 Notes: 12 tOE HIGH Z tWR 1. Toggling either OE or CE or both OE and CE will operate toggle bit. The tOEHP specification must be met by the toggling input(s). 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. AT49BV/LV2048A 1914D–FLASH–03/02 AT49BV/LV2048A (1) Software Product Identification Entry(1) Boot Block Lockout Enable Algorithm LOAD DATA AA TO ADDRESS 5555 LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 80 TO ADDRESS 5555 LOAD DATA 90 TO ADDRESS 5555 LOAD DATA AA TO ADDRESS 5555 ENTER PRODUCT IDENTIFICATION MODE(2)(3)(5) Software Product Identification Exit LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA OR (1)(6) LOAD DATA F0 TO ANY ADDRESS LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 40 TO ADDRESS 5555 EXIT PRODUCT IDENTIFICATION MODE(4) LOAD DATA F0 TO ADDRESS 5555 PAUSE 1 second(2) 7. Data Format: I/O15 - I/O8 (Don’t Care); I/O7 - I/O0 (Hex) Address Format: A15 - A0 (Hex), A-1, and A15 - A16 (Don’t Care). 8. Boot Block Lockout feature enabled. EXIT PRODUCT IDENTIFICATION MODE(4) Notes: 1. Data Format: I/O15 - I/O8 (Don’t Care); I/O7 - I/O0 (Hex) 2. 3. 4. 5. 6. Address Format: A15 - A0 (Hex), A-1, and A15 - A16 (Don’t Care). A1 - A16 = VIL. Manufacturer Code is read for A0 = VIL; Device Code is read for A0 = VIH. The device does not remain in identification mode if powered down. The device returns to standard operation mode. Manufacturer Code: 001FH Device Code: 0082H Either one of the Product ID Exit commands can be used. 13 1914D–FLASH–03/02 Ordering Information ICC (mA) tACC (ns) Active Standby 70 25 0.05 90 25 0.05 120 25 0.05 Ordering Code Package Operation Range AT49LV2048A-70RC AT49LV2048A-70TC 44R 48T Commercial (0° to 70°C) AT49BV2048A-90TC 48T Commercial (0° to 70°C) AT49BV2048A-90TI 48T Industrial (-40° to 85°C) AT49BV2048A-12TC 48T Commercial (0° to 70°C) AT49BV2048A-12TI 48T Industrial (-40° to 85°C) Package Type 44R 44-lead, 0.525" Wide, Plastic Gull Wing Small Outline (SOIC) 48T 48-lead, 12 x 20 mm, Plastic Thin Small Outline Package (TSOP) 14 AT49BV/LV2048A 1914D–FLASH–03/02 AT49BV/LV2048A Packaging Information 44R – SOIC Dimensions in Millimeters and (Inches). Controlling dimension: Inches. 0.508(0.020) 0.356(0.014) 13.46(0.530) 13.21(0.520) 16.18(0.637) 15.82(0.623) PIN 1 1.27(0.050) BSC 28.32(1.115) 28.07(1.105) 2.67(0.105) 2.41(0.095) 0.33(0.130) 1.27(0.050) 0.250(0.010) 0.100(0.004) 0º ~ 8º 1.00(0.039) 0.60(0.024) 04/11/01 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 44R, 44-lead (0.525" Body) Plastic Gull Wing Small Outline (SOIC) DRAWING NO. REV. 44R A 15 1914D–FLASH–03/02 48T – TSOP PIN 1 0º ~ 8º c Pin 1 Identifier D1 D L b e L1 A2 E A GAGE PLANE SEATING PLANE COMMON DIMENSIONS (Unit of Measure = mm) A1 SYMBOL Notes: 1. This package conforms to JEDEC reference MO-142, Variation DD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. MIN NOM MAX NOTE A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 19.80 20.00 20.20 D1 18.30 18.40 18.50 Note 2 E 11.90 12.00 12.10 Note 2 L 0.50 0.60 0.70 L1 0.25 BASIC b 0.17 0.22 0.27 c 0.10 – 0.21 e 0.50 BASIC 10/18/01 R 16 2325 Orchard Parkway San Jose, CA 95131 TITLE 48T, 48-lead (12 x 20 mm Package) Plastic Thin Small Outline Package, Type I (TSOP) DRAWING NO. REV. 48T B AT49BV/LV2048A 1914D–FLASH–03/02 Atmel Headquarters Atmel Operations Corporate Headquarters Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600 Europe Atmel SarL Route des Arsenaux 41 Casa Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan Atmel Japan K.K. 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 Atmel Corporate 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 436-4270 FAX 1(408) 436-4314 Microcontrollers Atmel Corporate 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 436-4270 FAX 1(408) 436-4314 Atmel Nantes La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards Atmel Rousset Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 RF/Automotive Atmel Heilbronn Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 Atmel Colorado Springs 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Atmel Grenoble Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80 Atmel Colorado Springs 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Atmel Smart Card ICs Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743 e-mail [email protected] Web Site http://www.atmel.com © Atmel Corporation 2002. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ATMEL ® is the registered trademark of Atmel; Battery-Voltage ™ is the trademark of Atmel. Other terms and product names may be the trademarks of others. Printed on recycled paper. 1914D–FLASH–03/02 /xM