BCD AP2112R5-1.2TRG1 600ma cmos ldo regulator with enable Datasheet

Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
General Description
Features
The AP2112 is CMOS process low dropout linear
regulator with enable function, the regulator delivers
a guaranteed 600mA (min.) continuous load current.
•
•
•
•
•
The AP2112 provides 1.2V, 1.8V, 2.5V, 2.6V, 2.8V
and 3.3V regulated output, and provides excellent
output accuracy ±1.5%, also provides an excellent
load regulation, line regulation and excellent load
transient performance due to very fast loop response.
The AP2112 has built-in auto discharge function.
•
•
•
•
•
•
•
•
The regulator features low power consumption, and
provides SOT-23-5, SOT-89-5, and SOIC-8 packages.
•
•
AP2112
Output Voltage Accuracy: ±1.5%
Output Current: 600mA (Min.)
Foldback Short Current Protection: 50mA
Enable Function to Turn ON/OFF VOUT
Low Dropout Voltage (3.3V): 250mV (Typ.)
@IOUT=600mA
Excellent Load Regulation: 0.2%/A (Typ.)
Excellent Line Regulation: 0.02%/V (Typ.)
Low Quiescent Current: 55µA (Typ.)
Low Standby Current: 0.01µA (Typ.)
Low Output Noise: 50µVRMS
PSRR: 100Hz -65dB, 1kHz -65dB
OTSD Protection
Stable with 1.0µF Flexible Cap: Ceramic,
Tantalum and Aluminum Electrolytic
Operation Temperature Range: -40°C to 85°C
ESD: MM 400V, HBM 4000V
Applications
•
•
•
SOT-23-5
Laptop Computer
Portable DVD
LCD Monitor
SOT-89-5
SOIC-8
Figure 1. Package Types of AP2112
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
1
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Pin Configuration
K Package
M Package
SOT-23-5
SOIC-8
R5/R5A Package
SOT-89-5
R5
R5A
VOUT
VIN
5
4
1
2
3
EN
GND
NC
Figure 2. Pin Configuration of AP2112 (Top View)
Pin Descriptions
PIN No.
Name
Descriptions
SOT-23-5
SOT-89-5
SOIC-8
1
4
8
VIN
Input Voltage
2
2
6, 7
GND
GND
5
EN
Chip Enable, H – normal work, L – shutdown output
2, 3, 4
NC
No Connection
1
VOUT
Output Voltage
3
4
5
Mar. 2012
3 (R5)
1 (R5A)
1 (R5)
3 (R5A)
5
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
2
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Functional Block Diagram
EN
VIN
Shutdown Logic
Foldback
Current Limit
Thermal
Shutdown
VOUT
3M
VREF
GND
Figure 3. Functional Block Diagram of AP2112
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
3
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Ordering Information
AP2112
G1: Green
Circuit Type
Blank: Tube
TR: Tape & Reel
Package
K: SOT-23-5
M: SOIC-8
R5/R5A: SOT-89-5
Package
Temperature
Range
Condition
1.2V
SOT-23-5
-40 to 85°C
SOT-89-5
-40 to 85°C
Tape & Reel
AP2112K-1.8TRG1
G3M
Tape & Reel
G3N
Tape & Reel
2.6V
AP2112K-2.6TRG1
G5N
Tape & Reel
2.8V
AP2112K-2.8TRG1
G3Q
Tape & Reel
3.3V
AP2112K-3.3TRG1
G3P
Tape & Reel
AP2112M-1.2G1
2112M-1.2G1
Tube
AP2112M-1.2TRG1
2112M-1.2G1
Tape & Reel
AP2112M-1.8G1
2112M-1.8G1
Tube
Tape & Reel
2.5V
AP2112M-1.8TRG1
2112M-1.8G1
AP2112M-2.5G1
2112M-2.5G1
AP2112M-2.5TRG1
2112M-2.5G1
AP2112M-2.6G1
2112M-2.6G1
AP2112M-2.6TRG1
2112M-2.6G1
Tube
Tape & Reel
Tube
Tape & Reel
AP2112M-3.3G1
2112M-3.3G1
Tube
AP2112M-3.3TRG1
2112M-3.3G1
Tape & Reel
1.2V(R5)
AP2112R5-1.2TRG1
G37D
Tape & Reel
1.8V(R5)
AP2112R5-1.8TRG1
G37E
Tape & Reel
2.5V(R5)
AP2112R5-2.5TRG1
G37F
Tape & Reel
2.6V(R5)
AP2112R5-2.6TRG1
G13F
Tape & Reel
3.3V
-40 to 85°C
G3L
Packing Type
AP2112K-2.5TRG1
2.6V
SOT-89-5
AP2112K-1.2TRG1
Marking ID
2.5V
1.8V
-40 to 85°C
Part Number
1.8V
1.2V
SOIC-8
1.2V: Fixed Output 1.2V
1.8V: Fixed Output 1.8V
2.5V: Fixed Output 2.5V
2.6V: Fixed Output 2.6V
2.8V: Fixed Output 2.8V
3.3V: Fixed Output 3.3V
3.3V(R5)
AP2112R5-3.3TRG1
G37G
Tape & Reel
1.2V(R5A)
AP2112R5A-1.2TRG1
G33C
Tape & Reel
1.8V(R5A)
AP2112R5A-1.8TRG1
G33E
Tape & Reel
2.5V(R5A)
AP2112R5A-2.5TRG1
G28G
Tape & Reel
2.6V(R5A)
AP2112R5A-2.6TRG1
G13E
Tape & Reel
3.3V(R5A)
AP2112R5A-3.3TRG1
G28H
Tape & Reel
BCD Semiconductor's Pb-free products, as designated with "G1" suffix in the part number, are RoHS compliant
and Green.
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
4
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Absolute Maximum Ratings (Note 1)
Parameter
Power Supply Voltage
Operating Junction Temperature
Range
Storage temperature Range
Lead Temperature (Soldering, 10
Seconds)
Thermal Resistance （Junction to
Ambient）(No Heatsink)
Symbol
Value
Unit
VCC
6.5
V
TJ
150
ºC
TSTG
-65 to 150
ºC
TLEAD
260
ºC
θJA
SOT-23-5
184
SOIC-8
114
SOT-89-5
120
°C /W
ESD (Machine Model)
400
V
ESD (Human Body Model)
4000
V
Note 1: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. These are stress ratings only, and functional operation of the device at these or any other conditions
beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute
Maximum Ratings” for extended periods may affect device reliability.
Recommended Operating Conditions
Parameter
Supply Voltage
Ambient Operation
Range
Mar. 2012
Temperature
Symbol
Min
Max
Unit
VIN
2.5
6.0
V
TA
-40
85
°C
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
5
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Electrical Characteristics
AP2112-1.2 Electrical Characteristic (Note 2)
VIN=2.5V, CIN=1.0µF (Ceramic), COUT=1.0µF (Ceramic), Typical TA= 25°C, Bold typeface applies over -40°C≤TJ≤85°C
ranges, unless otherwise specified (Note 3).
Parameter
Output Voltage
Maximum Output
Current
Load Regulation
Line Regulation
Dropout Voltage
Quiescent Current
Symbol
VOUT
IOUT(MAX)
(△VOUT/VOUT)/
△IOUT
(△VOUT/VOUT)/
△VIN
VDROP
IQ
Standby Current
ISTD
Power Supply
Rejection Ratio
PSRR
Output Voltage
Temperature
Coefficient
(△VOUT/VOUT)/ △T
Test Conditions
VIN =2.5V, 1mA ≤ IOUT ≤ 30mA
VIN =2.5V,
VOUT=1.182V to 1.218V
VIN=2.5V, 1mA ≤ IOUT ≤600mA
Min
Typ
Max
Unit
VOUT
*98.5%
1.2
VOUT
*101.5%
V
600
mA
-1
0.2
1
%/A
-0.1
0.02
0.1
%/V
IOUT =10mA
1000
1300
IOUT =300mA
1000
1300
IOUT=600mA
1000
1300
55
80
µA
0.01
1.0
µA
2.5V≤VIN≤6V, IOUT=30mA
VIN=2.5V, IOUT=0mA
VIN=2.5V, VEN in OFF mode
Ripple 0.5Vp-p
VIN=2.5V,
IOUT=100mA
f=100Hz
65
f=1KHz
65
IOUT=30mA
TA =-40°C to 85°C
mV
dB
±100
ppm/°C
Short Current Limit
ISHORT
VOUT=0V
50
mA
RMS Output Noise
VNOISE
No Load, 10Hz ≤ f ≤100kHz
50
µVRMS
VEN High Voltage
VIH
Enable logic high, regulator on
1.5
6.0
VEN Low Voltage
VIL
Enable logic low, regulator off
0
0.4
Start-up Time
EN Pull Down Resistor
VOUT
discharge
Resistor
Thermal
Shutdown
Temperature
Thermal
Shutdown
Hysteresis
Thermal Resistance
tS
No Load
RPD
RDCHG
Set EN pin at Low
20
µs
3.0
MΩ
60
Ω
TOTSD
160
THYOTSD
25
θJC
V
°C
SOT-23-5
96
SOIC-8
75
SOT-89-5
47
°C/W
Note 2: To prevent the Short Circuit Current protection feature from being prematurely activated, the input
voltage must be applied before a current source load is applied.
Note 3: Production testing at TA=25°C. Over temperature specifications guaranteed by design only.
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
6
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Electrical Characteristics (Continued)
AP2112-1.8 Electrical Characteristic (Note 2)
VIN=2.8V, CIN=1µF (Ceramic), COUT=1µF (Ceramic), Typical TA= 25°C, Bold typeface applies over -40°C≤TJ≤85°C ranges,
unless otherwise specified (Note 3).
Parameter
Output Voltage
Maximum Output Current
Symbol
Test Conditions
Min
Typ
Max
Unit
VOUT
VIN =2.8V, 1mA ≤ IOUT ≤ 30mA
VOUT
*98.5%
1.8
VOUT
*101.5%
V
IOUT(MAX)
(△VOUT/VOUT)/
△IOUT
(△VOUT/VOUT)/
△VIN
Load Regulation
Line Regulation
Dropout Voltage
VDROP
Quiescent Current
Standby Current
IQ
ISTD
Power Supply Rejection
Ratio
Output Voltage
Temperature Coefficient
PSRR
(△VOUT/VOUT)/ △T
VIN=2.8V,
VOUT=1.773V to 1.827V
VOUT=1.8V,
VIN=VOUT+1V,
1mA ≤ IOUT ≤600mA
600
mA
-1
0.2
1
%/A
-0.1
0.02
0.1
%/V
IOUT =10mA
500
700
IOUT =300mA
500
700
IOUT=600mA
500
700
VIN=2.8V, IOUT=0mA
55
80
µA
0.01
1.0
µA
2.8V≤VIN≤6V, IOUT=30mA
VIN=2.8V, VEN in OFF mode
Ripple 0.5Vp-p
VIN=2.8V,
IOUT=100mA
f=100Hz
65
f=1KHz
65
mV
dB
IOUT=30mA
TA =-40°C to 85°C
±100
ppm/°C
Short Current Limit
ISHORT
VOUT=0V
50
mA
RMS Output Noise
VNOISE
No Load, 10Hz ≤ f ≤100kHz
50
µVRMS
VEN High Voltage
VIH
Enable logic high, regulator on
1.5
6.0
VEN Low Voltage
VIL
Enable logic low, regulator off
0
0.4
Start-up Time
tS
EN Pull Down Resistor
RPD
VOUT Discharge Resistor
RDCHG
Thermal
Temperature
Thermal
Hysteresis
Shutdown
Shutdown
Thermal Resistance
No Load
Set EN pin at Low
20
µs
3.0
MΩ
60
Ω
TOTSD
160
THYOTSD
25
θJC
V
°C
SOT-23-5
96
SOIC-8
75
SOT-89-5
47
°C/W
Note 2: To prevent the Short Circuit Current protection feature from being prematurely activated, the input
voltage must be applied before a current source load is applied.
Note 3: Production testing at TA=25°C. Over temperature specifications guaranteed by design only.
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
7
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Electrical Characteristics (Continued)
AP2112-2.5 Electrical Characteristic (Note 2)
VIN=3.5V, CIN=1µF (Ceramic), COUT=1µF (Ceramic), Typical TA= 25°C, Bold typeface applies over -40°C≤TJ≤85°C ranges,
unless otherwise specified (Note 3).
Parameter
Output Voltage
Maximum Output Current
Symbol
Test Conditions
Min
Typ
Max
Unit
VOUT
VIN =3.5V, 1mA ≤ IOUT ≤ 30mA
VOUT
*98.5%
2.5
VOUT
*101.5%
V
IOUT(MAX)
(△VOUT/VOUT)/
△IOUT
(△VOUT/VOUT)/
△VIN
Load Regulation
Line Regulation
Dropout Voltage
VDROP
Quiescent Current
Standby Current
IQ
ISTD
Power Supply Rejection
Ratio
Output Voltage
Temperature Coefficient
PSRR
(△VOUT/VOUT)/ △T
VIN=3.5V, VOUT=2.463V to
2.537V
VOUT=2.5V,
VIN=VOUT+1V,
1mA ≤ IOUT ≤600mA
600
mA
-1
0.2
1
%/A
-0.1
0.02
0.1
%/V
IOUT =10mA
5
8
IOUT =300mA
125
200
IOUT=600mA
250
400
VIN=3.5V, IOUT=0mA
55
80
µA
0.01
1.0
µA
3.5V≤VIN≤6V, IOUT=30mA
VIN=3.5V, VEN in OFF mode
Ripple 0.5Vp-p
VIN=3.5V,
IOUT=100mA
f=100Hz
65
f=1KHz
65
mV
dB
IOUT=30mA
TA =-40°C to 85°C
±100
ppm/°C
Short Current Limit
ISHORT
VOUT=0V
50
mA
RMS Output Noise
VNOISE
No Load, 10Hz ≤ f ≤100kHz
50
µVRMS
VEN High Voltage
VIH
Enable logic high, regulator on
1.5
6.0
VEN Low Voltage
VIL
Enable logic low, regulator off
0
0.4
Start-up Time
tS
EN Pull Down Resistor
RPD
VOUT Discharge Resistor
RDCHG
Thermal
Temperature
Thermal
Hysteresis
Shutdown
Shutdown
Thermal Resistance
No Load
Set EN pin at Low
20
µs
3.0
MΩ
60
Ω
TOTSD
160
THYOTSD
25
θJC
V
°C
SOT-23-5
96
SOIC-8
75
SOT-89-5
47
°C/W
Note 2: To prevent the Short Circuit Current protection feature from being prematurely activated, the input
voltage must be applied before a current source load is applied.
Note 3: Production testing at TA=25°C. Over temperature specifications guaranteed by design only.
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
8
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Electrical Characteristics (Continued)
AP2112-2.6 Electrical Characteristic (Note 2)
VIN=3.6V, CIN=1µF (Ceramic), COUT=1µF (Ceramic), Typical TA= 25°C, Bold typeface applies over -40°C≤TJ≤85°C ranges,
unless otherwise specified (Note 3).
Parameter
Output Voltage
Symbol
VOUT
Maximum Output Current
IOUT(MAX)
△VOUT/VOUT)/
△IOUT
(△VOUT/VOUT)/
△VIN
Load Regulation
Line Regulation
Dropout Voltage
VDROP
Quiescent Current
Standby Current
IQ
ISTD
Power Supply Rejection
Ratio
Output Voltage
Temperature Coefficient
PSRR
(△VOUT/VOUT)/ △T
Test Conditions
VIN =3.6V, 1mA ≤ IOUT ≤ 30mA
VIN=3.6V, VOUT=2.561V to
2.639V
VOUT=2.6V, VIN=VOUT+1V, 1mA
≤ IOUT ≤600mA
Min
Typ
Max
Unit
VOUT
*98.5%
2.6
VOUT
*101.5%
V
600
mA
-1
0.2
1
%/A
-0.1
0.02
0.1
%/V
IOUT =10mA
5
8
IOUT =300mA
125
200
IOUT=600mA
250
400
VIN=3.6V, IOUT=0mA
55
80
µA
0.01
1.0
µA
3.6V≤VIN≤6V, IOUT=30mA
VIN=3.6V, VEN in OFF mode
Ripple 0.5Vp-p f=100Hz
VIN=3.6V,
f=1KHz
IOUT=100mA
mV
65
dB
65
IOUT=30mA
±100
TA =-40°C to 85°C
ppm/°C
Short Current Limit
ISHORT
VOUT=0V
50
mA
RMS Output Noise
VNOISE
No Load, 10Hz ≤ f ≤100kHz
50
µVRMS
VEN High Voltage
VIH
Enable logic high, regulator on
1.5
6.0
VEN Low Voltage
VIL
Enable logic low, regulator off
0
0.4
Start-up Time
tS
EN Pull Down Resistor
RPD
VOUT Discharge Resistor
RDCHG
Thermal
Temperature
Thermal
Hysteresis
Shutdown
Shutdown
Thermal Resistance
No Load
Set EN pin at Low
20
µs
3.0
MΩ
60
Ω
TOTSD
160
THYOTSD
25
θJC
V
°C
SOT-23-5
96
SOIC-8
75
SOT-89-5
47
°C/W
Note 2: To prevent the Short Circuit Current protection feature from being prematurely activated, the input
voltage must be applied before a current source load is applied.
Note 3: Production testing at TA=25°C. Over temperature specifications guaranteed by design only.
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
9
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Electrical Characteristics (Continued)
AP2112-2.8 Electrical Characteristic (Note 2)
VIN=3.8V, CIN=1µF (Ceramic), COUT=1µF (Ceramic), Typical TA = 25°C, Bold typeface applies over -40°C≤TJ≤85°C ranges,
unless otherwise specified (Note 3).
Parameter
Output Voltage
Maximum Output Current
Symbol
Test Conditions
Min
Typ
Max
Unit
VOUT
VIN =3.8V, 1mA ≤ IOUT ≤ 30mA
VOUT
*98.5%
2.8
VOUT
*101.5%
V
IOUT(MAX)
(△VOUT/VOUT)/
△IOUT
(△VOUT/VOUT)/
△VIN
Load Regulation
Line Regulation
Dropout Voltage
VDROP
Quiescent Current
Standby Current
IQ
ISTD
Power Supply Rejection
Ratio
Output Voltage
Temperature Coefficient
PSRR
(△VOUT/VOUT)/ △T
VIN=3.8V, VOUT=2.758V to
2.842V
VOUT=2.8V,
VIN=VOUT+1V,
1mA ≤ IOUT ≤600mA
600
mA
-1
0.2
1
%/A
-0.1
0.02
0.1
%/V
IOUT =10mA
5
8
IOUT =300mA
125
200
IOUT=600mA
250
400
VIN=3.8V, IOUT=0mA
55
80
µA
0.01
1.0
µA
3.8V≤VIN≤6V, IOUT=30mA
VIN=3.8V, VEN in OFF mode
Ripple 0.5Vp-p
VIN=3.8V,
IOUT=100mA
f=100Hz
65
f=1KHz
65
mV
dB
IOUT=30mA
TA =-40°C to 85°C
±100
ppm/°C
Short Current Limit
ISHORT
VOUT=0V
50
mA
RMS Output Noise
VNOISE
No Load, 10Hz ≤ f ≤100kHz
50
µVRMS
VEN High Voltage
VIH
Enable logic high, regulator on
1.5
6.0
VEN Low Voltage
VIL
Enable logic low, regulator off
0
0.4
Start-up Time
tS
EN Pull Down Resistor
RPD
VOUT Discharge Resistor
RDCHG
Thermal
Temperature
Thermal
Hysteresis
Shutdown
Shutdown
Thermal Resistance
No Load
Set EN pin at Low
20
µs
3.0
MΩ
60
Ω
TOTSD
160
THYOTSD
25
θJC
V
°C
SOT-23-5
96
SOIC-8
75
SOT-89-5
47
°C/W
Note 2: To prevent the Short Circuit Current protection feature from being prematurely activated, the input
voltage must be applied before a current source load is applied.
Note 3: Production testing at TA=25°C. Over temperature specifications guaranteed by design only.
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
10
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Electrical Characteristics (Continued)
AP2112-3.3 Electrical Characteristic (Note 2)
VIN=4.3V, CIN=1µF (Ceramic), COUT=1µF (Ceramic), Typical TA = 25°C, Bold typeface applies over -40°C≤TJ≤85°C ranges,
unless otherwise specified (Note 3).
Parameter
Output Voltage
Maximum Output Current
Symbol
Test Conditions
Min
Typ
Max
Unit
VOUT
VIN =4.3V, 1mA ≤ IOUT ≤ 30mA
VOUT
*98.5%
3.3
VOUT
*101.5%
V
IOUT(MAX)
(△VOUT/VOUT)/
△IOUT
(△VOUT/VOUT)/
△VIN
Load Regulation
Line Regulation
Dropout Voltage
VDROP
Quiescent Current
Standby Current
IQ
ISTD
Power Supply Rejection
Ratio
Output Voltage
Temperature Coefficient
PSRR
(△VOUT/VOUT)/ △T
VIN=4.3V,
3.350V
VOUT=3.251V
to
VIN=4.3V, 1mA ≤ IOUT ≤600mA
600
mA
-1
0.2
1
%/A
-0.1
0.02
0.1
%/V
IOUT =10mA
5
8
IOUT =300mA
125
200
IOUT=600mA
250
400
VIN=4.3V, IOUT=0mA
55
80
µA
0.01
1.0
µA
4.3V≤VIN≤6V, IOUT=30mA
VIN=4.3V, VEN in OFF mode
Ripple 0.5Vp-p
VIN=4.3V,
IOUT=100mA
f=100Hz
65
f=1KHz
65
mV
dB
IOUT=30mA
TA =-40°C to 85°C
±100
ppm/°C
Short Current Limit
ISHORT
VOUT=0V
50
mA
RMS Output Noise
VNOISE
No Load, 10Hz ≤ f ≤100kHz
50
µVRMS
VEN High Voltage
VIH
Enable logic high, regulator on
1.5
6.0
VEN Low Voltage
VIL
Enable logic low, regulator off
0
0.4
Start-up Time
tS
EN Pull Down Resistor
RPD
VOUT Discharge Resistor
RDCHG
Thermal
Temperature
Thermal
Hysteresis
Shutdown
Shutdown
Thermal Resistance
No Load
Set EN pin at Low
20
µs
3.0
MΩ
60
Ω
TOTSD
160
THYOTSD
25
θJC
V
°C
SOT-23-5
96
SOIC-8
75
SOT-89-5
47
°C/W
Note 2: To prevent the Short Circuit Current protection feature from being prematurely activated, the input
voltage must be applied before a current source load is applied.
Note 3: Production testing at TA =25°C. Over temperature specifications guaranteed by design only.
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
11
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
1.6
4.0
1.4
3.5
1.2
3.0
Output Voltage (V)
Output Voltage (V)
Typical Performance Characteristics
1.0
0.8
NO Load
0.6
o
TA=-40 C
2.5
2.0
No Load
1.5
o
TA=-40 C
o
TA=25 C
0.4
o
o
TA=85 C
VOUT=1.2V
0.2
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0.5
TA=85 C
VOUT=3.3V
o
0.0
0.0
1.0
TA=25 C
5.5
0.0
0.0
6.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
Input Voltage (V)
Input Voltage (V)
Figure 4. Output Voltage vs. Input Voltage
Figure 5. Output Voltage vs. Input Voltage
70
70
68
VIN=2.5V
No Load
64
62
60
58
56
54
52
50
40
O
TA=-40 C
O
48
0
0.0
20.0
40.0
60.0
1.0
80.0
o
Temperature ( C)
TA=85 C
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
Input Voltage (V)
Figure 6. Quiescent Current vs. Temperature
Mar. 2012
TA=25 C
20
10
-20.0
O
30
50
46
-40.0
No Load
60
Quiescent Current (µA)
Quiescent Current (µA)
66
Figure 7. Quiescent Current vs. Input Voltage
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
12
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Typical Performance Characteristics (Continued)
1.210
3.35
VIN=2.5V
CIN=1µF
COUT=1µF
3.33
1.206
1.204
-20.0
0.0
20.0
40.0
60.0
3.31
3.30
IOUT=10mA
IOUT=100mA
IOUT=300mA
IOUT=600mA
3.29
3.27
IOUT=300mA
IOUT=600mA
1.200
-40.0
3.32
3.28
IOUT=10mA
IOUT=100mA
1.202
VIN=4.3V
CIN=1µF
COUT=1µF
3.34
Output Voltage (V)
Output Voltage (V)
1.208
3.26
3.25
-40
80.0
-20
0
20
40
60
80
o
Temperature( C)
o
Temperature ( C)
Figure 8. Output Voltage vs. Temperature
Figure 9. Output Voltage vs. Temperature
1.3
4.0
1.2
1.1
3.5
TA=25 C
3.0
TA= -40 C
1.0
o
0.9
o
TA=85 C
0.8
Output Voltage (V)
Output Voltage (V)
o
0.7
0.6
0.5
0.4
0.3
VIN=4.3V
2.5
o
TA=-40 C
o
TA= 25 C
2.0
o
TA= 85 C
1.5
1.0
0.5
0.2
VIN=2.5V
0.1
0.0
0.0
-0.5
0.0
-0.1
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
Output Current (A)
Output Current (A)
Figure 10. Output Voltage vs. Output Current
Mar. 2012
0.1
Figure 11. Output Voltage vs. Output Current
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
13
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Typical Performance Characteristics (Continued)
4.0
1.2
VIN=2.5V
0.8
VIN=5.5V
3.5
3.0
VIN=5V
Output Voltage (V)
Output Voltage (V)
VIN=2V
1.0
VIN=6V
0.6
0.4
o
TA=25 C
CIN=1µF
COUT=1µF
0.2
VIN=4.0V
VIN=4.3V
VIN=5.0V
VIN=5.5V
VIN=6.0V
2.5
2.0
1.5
1.0
o
TA=25 C
CIN=1µF
COUT=1µF
0.5
0.0
0.0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0.0
1.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
Output Current (A)
Output Current (A)
Figure 12. Output Voltage vs. Output Current
Figure 13. Output Voltage vs. Output Current
350
300
260
TA=-40 C
220
TA= 25 C
200
TA= 85 C
VIN=4.3V
o
o
o
o
Ground Current (µA)
Dropout Voltage (mV)
o
TA= 25 C
250
240
o
TA=-40 C
TA= 85 C
VOUT=3.3V
200
150
100
180
160
140
120
100
80
50
60
0
0.0
0.1
0.2
0.3
0.4
0.5
40
0.0
0.6
0.1
0.2
0.3
0.4
0.5
0.6
Output Current (A)
Output Current (A)
Figure 14. Dropout Voltage vs. Output Current
Figure 15. Ground Current vs. Output Current
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
14
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Typical Performance Characteristics (Continued)
70
VIN=2.5V, CIN=1µF, COUT=1µF
65
PSRR (dB)
60
CH1: VOUT
10mV/div
55
IOUT=10mA
50
600mA
IOUT=100mA
45
IOUT=300mA
40
VOUT=1.2V
35
VIN=2.5V
0mA
CH2: IOUT
200mA/div
Ripple=0.5V
30
20
100
1k
10k
100k
Frequency (Hz)
Figure 16. PSRR vs. Frequency
VIN
(2V/div)
Figure 17. Load Transient
VIN
(2V/div)
VEN
(2V/div)
VEN
(2V/div)
VOUT
(2V/div)
VOUT
(2V/div)
200µs/div
20µs/div
Figure 18. Enable On
Mar. 2012
Figure 19. Enable Off
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
15
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Typical Application (Note 4)
VOUT
VIN
CIN
1 F
1.2V/1.8V/
2.5V/2.6V/
2.8V/3.3V
COUT
1 F
AP2112
VEN
ON
OFF
GND
Note 4: It is recommended to use X7R or X5R dielectric capacitor if 1.0µF ceramic capacitor is selected as
input/output capacitors.
Figure 20. AP2112 Typical Application
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
16
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Mechanical Dimensions
SOT-23-5
Unit: mm(inch)
2.820(0.111)
3.020(0.119)
0.100(0.004)
0.200(0.008)
0.200(0.008)
0.700(0.028)
REF
0.950(0.037)
TYP
0.300(0.012)
0.400(0.016)
0°
8°
1.800(0.071)
2.000(0.079)
0.000(0.000)
0.150(0.006)
0.900(0.035)
1.300(0.051)
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
17
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Mechanical Dimensions (Continued)
SOT-89-5
1.550(0.061)REF
Unit: mm(inch)
4.400(0.173)
4.600(0.181)
1.400(0.055)
1.030(0.041)REF
1.600(0.063)
45
0.900(0.035)
1.100(0.043)
2.300(0.091)
2.600(0.102)
3.950(0.156)
4.250(0.167)
2.060(0.081)REF
3
0.900(0.035)
1.100(0.043)
0.520(0.020)
0.350(0.014)
0.320(0.013)
0.320(0.013)
0.480(0.019)
10
0.450(0.018)
0.520(0.020)
3.000(0.118)
TYP
1.500(0.059)
1.800(0.071)
0.320(0.013)REF
3
2.210(0.087)REF
1.620(0.064)REF
R0.150(0.006)
10
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
18
Data Sheet
600mA CMOS LDO REGULATOR WITH ENABLE
AP2112
Mechanical Dimensions (Continued)
SOIC-8
4.700(0.185)
5.100(0.201)
7°
Unit: mm(inch)
0.320(0.013)
1.350(0.053)
1.750(0.069)
8°
8°
7°
0.675(0.027)
0.725(0.029)
D
5.800(0.228)
1.270(0.050)
6.200(0.244)
TYP
D
20:1
0.800(0.031)
0.300(0.012)
R0.150(0.006)
0.100(0.004)
0.200(0.008)
0°
8°
1.000(0.039)
3.800(0.150)
4.000(0.157)
0.330(0.013)
0.190(0.007)
0.250(0.010)
1°
5°
0.510(0.020)
0.900(0.035)
R0.150(0.006)
0.450(0.017)
0.800(0.031)
Note: Eject hole, oriented hole and mold mark is optional.
Mar. 2012
Rev. 1. 4
BCD Semiconductor Manufacturing Limited
19
BCD Semiconductor Manufacturing Limited
http://www.bcdsemi.com
IMPORTANT NOTICE
IMPORTANT
NOTICE
BCD Semiconductor
BCD
Semiconductor Manufacturing
Manufacturing Limited
Limited reserves
reserves the
the right
right to
to make
make changes
changes without
without further
further notice
notice to
to any
any products
products or
or specifispecifications herein.
cations
herein. BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited does
does not
not assume
assume any
any responsibility
responsibility for
for use
use of
of any
any its
its products
products for
for any
any
particular purpose,
particular
purpose, nor
nor does
does BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited assume
assume any
any liability
liability arising
arising out
out of
of the
the application
application or
or use
use
of any
of
any its
its products
products or
or circuits.
circuits. BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited does
does not
not convey
convey any
any license
license under
under its
its patent
patent rights
rights or
or
other rights
other
rights nor
nor the
the rights
rights of
of others.
others.
MAIN SITE
SITE
MAIN
- Headquarters
BCD
Semiconductor Manufacturing Limited
BCD
Semiconductor
Manufacturing Limited
- Wafer
Fab
No.
1600, Zi
Xing Road,
Shanghai ZiZhu
Science-basedLimited
Industrial Park, 200241, China
Shanghai
SIM-BCD
Semiconductor
Manufacturing
Tel:
Fax: +86-21-24162277
800,+86-21-24162266,
Yi Shan Road, Shanghai
200233, China
Tel: +86-21-6485 1491, Fax: +86-21-5450 0008
REGIONAL SALES OFFICE
Shenzhen OfficeSALES OFFICE
REGIONAL
- Wafer
FabSemiconductor Manufacturing Limited
BCD
Shanghai
SIM-BCD
Semiconductor Manufacturing Co., Ltd.
- IC Design
Group
800 Yi
Shan Road,
Shanghai
200233,
China Corporation
Advanced
Analog
Circuits
(Shanghai)
Tel: +86-21-6485
1491,YiFax:
0008200233, China
8F, Zone B, 900,
Shan+86-21-5450
Road, Shanghai
Tel: +86-21-6495 9539, Fax: +86-21-6485 9673
Taiwan Office
Shanghai
Semiconductor Manufacturing Co., Ltd., Shenzhen Office
BCD Taiwan
Semiconductor
Shenzhen SIM-BCD
Office
Office (Taiwan) Company Limited
Unit
A Room
1203, Skyworth
Bldg., Gaoxin
Ave.1.S., Nanshan
Shenzhen,
4F, 298-1,
Guang Road,(Taiwan)
Nei-Hu District,
Taipei,
Shanghai
SIM-BCD
Semiconductor
Manufacturing
Co., Ltd.District,
Shenzhen
Office
BCDRui
Semiconductor
Company
Limited
China
Taiwan
Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office
4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei,
Tel:
+86-755-8826
Tel: +886-2-2656
2808
Room
E, 5F, Noble 7951
Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China
Taiwan
Fax:
+86-755-88267951
7865
Fax: +886-2-2656
28062808
Tel: +86-755-8826
Tel: +886-2-2656
Fax: +86-755-8826 7865
Fax: +886-2-2656 2806
USA Office
BCD Office
Semiconductor Corp.
USA
30920Semiconductor
Huntwood Ave.Corporation
Hayward,
BCD
CA 94544,
USA Ave. Hayward,
30920
Huntwood
Tel :94544,
+1-510-324-2988
CA
U.S.A
Fax:: +1-510-324-2988
+1-510-324-2788
Tel
Fax: +1-510-324-2788