Bourns BD250B Pnp silicon power transistor Datasheet

BD250, BD250A, BD250B, BD250C
PNP SILICON POWER TRANSISTORS
●
Designed for Complementary Use with the
BD249 Series
●
125 W at 25°C Case Temperature
●
25 A Continuous Collector Current
●
40 A Peak Collector Current
●
Customer-Specified Selections Available
SOT-93 PACKAGE
(TOP VIEW)
B
1
C
2
E
3
Pin 2 is in electrical contact with the mounting base.
MDTRAAA
absolute maximum ratings at 25°C case temperature (unless otherwise noted)
RATING
SYMBOL
Collector-emitter voltage (RBE = 100 Ω)
BD250B
Collector-emitter voltage (IC = -30 mA)
VCER
-115
-45
V CEO
Peak collector current (see Note 1)
Continuous base current
Continuous device dissipation at (or below) 25°C case temperature (see Note 2)
Continuous device dissipation at (or below) 25°C free air temperature (see Note 3)
Unclamped inductive load energy (see Note 4)
Operating junction temperature range
Storage temperature range
Lead temperature 3.2 mm from case for 10 seconds
NOTES: 1.
2.
3.
4.
-60
V
-80
-100
BD250C
Continuous collector current
V
-90
BD250C
BD250B
Emitter-base voltage
-70
BD250
BD250A
UNIT
-55
BD250
BD250A
VALUE
VEBO
-5
V
IC
-25
A
ICM
-40
A
IB
-5
A
Ptot
125
W
Ptot
3
W
½LIC2
90
mJ
°C
Tj
-65 to +150
Tstg
-65 to +150
°C
TL
250
°C
This value applies for tp ≤ 0.3 ms, duty cycle ≤ 10%.
Derate linearly to 150°C case temperature at the rate of 1 W/°C.
Derate linearly to 150°C free air temperature at the rate of 24 mW/°C.
This rating is based on the capability of the transistor to operate safely in a circuit of: L = 20 mH, IB(on) = -0.4 A, RBE = 100 Ω,
VBE(off) = 0, RS = 0.1 Ω, VCC = -20 V.
JUNE 1973 - REVISED SEPTEMBER 2002
Specifications are subject to change without notice.
1
BD250, BD250A, BD250B, BD250C
PNP SILICON POWER TRANSISTORS
electrical characteristics at 25°C case temperature
PARAMETER
V(BR)CEO
ICES
ICEO
IEBO
hFE
V CE(sat)
VBE
hfe
|hfe |
Collector-emitter
breakdown voltage
TEST CONDITIONS
IC = -30 mA
MIN
IB = 0
(see Note 5)
BD250
-45
BD250A
-60
BD250B
-80
BD250C
-100
TYP
MAX
V
VCE = -55 V
VBE = 0
BD250
-0.7
Collector-emitter
VCE = -70 V
VBE = 0
BD250A
-0.7
cut-off current
VCE = -90 V
VBE = 0
BD250B
-0.7
VCE = -115 V
VBE = 0
BD250C
-0.7
Collector cut-off
VCE = -30 V
IB = 0
BD250/250A
-1
current
VCE = -60 V
IB = 0
BD250B/250C
-1
VEB =
-5 V
IC = 0
Emitter cut-off
current
Forward current
transfer ratio
VCE =
-4 V
IC = -1.5 A
-4 V
IC = -15 A
VCE =
-4 V
IC = -25 A
Collector-emitter
IB =
-1.5 A
IC = -15 A
saturation voltage
IB =
-5 A
IC = -25 A
Base-emitter
VCE =
-4 V
IC = -15 A
voltage
VCE =
-4 V
IC = -25 A
Small signal forward
current transfer ratio
Small signal forward
current transfer ratio
mA
mA
-1
VCE =
UNIT
mA
25
(see Notes 5 and 6)
10
5
-1.8
(see Notes 5 and 6)
-4
-2
(see Notes 5 and 6)
V
-4
VCE = -10 V
IC =
- 1A
f = 1 kHz
25
VCE = -10 V
IC =
-1 A
f = 1 MHz
3
V
NOTES: 5. These parameters must be measured using pulse techniques, tp = 300 µs, duty cycle ≤ 2%.
6. These parameters must be measured using voltage-sensing contacts, separate from the current carrying contacts.
thermal characteristics
MAX
UNIT
RθJC
Junction to case thermal resistance
PARAMETER
MIN
TYP
1
°C/W
RθJA
Junction to free air thermal resistance
42
°C/W
MAX
UNIT
resistive-load-switching characteristics at 25°C case temperature
PARAMETER
†
TEST CONDITIONS
†
MIN
ton
Turn-on time
IC = -5 A
IB(on) = -0.5 A
IB(off) = 0.5 A
0.2
µs
toff
Turn-off time
VBE(off) = 5 V
RL = 5 Ω
tp = 20 µs, dc ≤ 2%
0.4
µs
Voltage and current values shown are nominal; exact values vary slightly with transistor parameters.
2
TYP
JUNE 1973 - REVISED SEPTEMBER 2002
Specifications are subject to change without notice.
BD250, BD250A, BD250B, BD250C
PNP SILICON POWER TRANSISTORS
TYPICAL CHARACTERISTICS
TYPICAL DC CURRENT GAIN
vs
COLLECTOR CURRENT
TCS636AD
VCE(sat) - Collector-Emitter Saturation Voltage - V
hFE - DC Current Gain
1000
COLLECTOR-EMITTER SATURATION VOLTAGE
vs
BASE CURRENT
VCE = -4 V
TC = 25°C
tp = 300 µs, duty cycle < 2%
100
10
1
-0·1
-1·0
-10
-100
TCS636AB
-10
-1·0
-0·1
-0·01
-0·001
-0·01
IC - Collector Current - A
-0·1
-1·0
-10
-25 A
-20 A
-15 A
-10 A
-100
IB - Base Current - A
Figure 1.
Figure 2.
BASE-EMITTER VOLTAGE
vs
COLLECTOR CURRENT
-1·8
VBE - Base-Emitter Voltage - V
IC =
IC =
IC =
IC =
IC = -300 mA
IC = -1 A
IC = -3 A
TCS636AC
VCE = -4 V
TC = 25°C
-1·6
-1·4
-1·2
-1·0
-0·8
-0·6
-0·1
-1·0
-10
-100
IC - Collector Current - A
Figure 3.
JUNE 1973 - REVISED SEPTEMBER 2002
Specifications are subject to change without notice.
3
BD250, BD250A, BD250B, BD250C
PNP SILICON POWER TRANSISTORS
MAXIMUM SAFE OPERATING REGIONS
MAXIMUM FORWARD-BIAS
SAFE OPERATING AREA
IC - Collector Current - A
-100
SAS636AB
tp = 300 µs, d = 0.1 = 10%
tp = 1 ms, d = 0.1 = 10%
tp = 10 ms, d = 0.1 = 10%
DC Operation
-10
-1·0
-0·1
BD250
BD250A
BD250B
BD250C
-0·01
-1·0
-10
-100
-1000
VCE - Collector-Emitter Voltage - V
Figure 4.
THERMAL INFORMATION
MAXIMUM POWER DISSIPATION
vs
CASE TEMPERATURE
TIS635AA
Ptot - Maximum Power Dissipation - W
140
120
100
80
60
40
20
0
0
25
50
75
100
125
150
TC - Case Temperature - °C
Figure 5.
4
JUNE 1973 - REVISED SEPTEMBER 2002
Specifications are subject to change without notice.
BD250, BD250A, BD250B, BD250C
PNP SILICON POWER TRANSISTORS
MECHANICAL DATA
SOT-93
3-pin plastic flange-mount package
This single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic
compound. The compound will withstand soldering temperature with no deformation, and circuit performance
characteristics will remain stable when operated in high humidity conditions. Leads require no additional
cleaning or processing when used in soldered assembly.
SOT-93
4,90
4,70
15,2
14,7
ø 4,1
4,0
3,95
4,15
1,37
1,17
16,2 MAX.
12,2 MAX.
31,0 TYP.
18,0 TYP.
1
2
3
1,30
0,78
0,50
1,10
11,1
10,8
2,50 TYP.
ALL LINEAR DIMENSIONS IN MILLIMETERS
NOTE A: The centre pin is in electrical contact with the mounting tab.
JUNE 1973 - REVISED SEPTEMBER 2002
Specifications are subject to change without notice.
MDXXAW
5
Similar pages