Pan Jit ER2E Surface mount superfast rectifier(voltage - 50 to 600 volts current - 2.0 amperes) Datasheet

ER2A THRU ER2J
SURFACE MOUNT SUPERFAST RECTIFIER
VOLTAGE - 50 to 600 Volts CURRENT - 2.0 Amperes
FEATURES
l For surface mounted applications
l Low profile package
l
l
Built-in strain relief
Easy pick and place
l
l
Superfast recovery times for high efficiency
Plastic package has Underwriters Laboratory
l
Flammability Classification 94V-O
Glass passivated junction
l
SMB/DO-214AA
High temperature soldering:
260 ¢J /10 seconds at terminals
MECHANICAL DATA
Case: JEDEC DO-214AA molded plastic
Terminals: Solder plated, solderable per
MIL-STD-750, Method 2026
Polarity: Indicated by cathode band
Standard packaging: 12mm tape (EIA-481)
Weight: 0.003 ounce, 0.093 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 ¢J ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current,
at TL=110 ¢J
Peak Forward Surge Current 8.3ms single half sinewave superimposed on rated load(JEDEC method)
Maximum Instantaneous Forward Voltage at 2.0A
Maximum DC Reverse Current TA=25 ¢J
At Rated DC Blocking Voltage TA=100 ¢J
Maximum Reverse Recovery Time (Note 1)
Typical Junction capacitance (Note 2)
Typical Thermal Resistance (Note 3)
Operating and Storage Temperature Range
SYMBOLS ER2A ER2B ER2C ER2D ER2E ER2G ER2J UNITS
50
100
150
200
300
400
600
Volts
VRRM
35
70
105
140
210
280
420
Volts
VRMS
50
100
150
200
300
400
600
Volts
VDC
I(AV)
2.0
Amps
IFSM
50.0
Amps
VF
IR
TRR
CJ
R £KJL
TJ ,TSTG
NOTES:
1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A
2. Measured at 1 MHz and Applied reverse voltage of 4.0 volts
2
3. 8.0mm (.013mm thick) land areas
0.95
1.25
5.0
150
35.0
25.0
20.0
-50 to +150
1.7
Volts
£g A
nS
PF
¢J /W
¢J
RATING AND CHARACTERISTIC CURVES
ER2A THRU ER2J
AVERAGE FORWARD RECTIFIED
CURRENT, AMPERES
trr
+0.5A
0
-0.25
NOTE:1.Rise Time = 7ns max.
Input Impedance = 1 megohm. 22pF
2.Rise Time = 10ns max.
-1.0
SET TIME
BASE FOR
Source Impedance = 50 Ohms
1cm
2.4
2.0
SINGLE PHASE HALF
WAVE 60Hz RESISTIVE
OR INDUCTIVE LOAD
P.C.B. MOUNTED ON
0.3×0.3"(8.0×8.0mm)
COPPER PAD AREAS
1.6
1.2
0.8
0.4
0
0
20
1,000
10
TJ = 75¢J
T J = 25¢J
1
0.1
20
40
60
80
100
120
100
120
140
160
50.0
ER2A
10.0
ER2E
1.0
ER2J
0.1
TJ = 25¢J
PULSE WIDTH = 300£gs
2% DUTY CYCLE
0.01
0
80
Fig. 2-MAXIMUM AVERAGE FORWARD
CURRENT RATING
INSTANTANEOUS FORWARD CURRENT
AMPERES
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND
TEST CIRCUIT DIAGRAM
T J = 100 ¢J
60
LEAD TEMPERATURE, ¢J
50 ns/cm
100
40
140
0.01
0.4
0.5
0.8
1.0
1.2
1.4
1.6 1.8
PERCENT OF RATED PEAK INVERSE VOLTAGE, VOLTS
REVERSE VOLTAGE, VOLTS
Fig. 4-TYPICAL FORWARD CHARACTERISTICS
60
60
50
CAPACITANCE, pF
PEAK FORWARD SURGE CURRENT,
AMPERES
Fig. 3-TYPICAL REVERSE CHARACTERISTICS
8.3ms SINGLE HALF SINE WAVE
JEDEC METHOD
40
30
20
10
50
40
30
TJ = 25 ¢J
20
f = 1.0MHz
Vsig = 50mVp-p
10
1
2
5
10
20
50
100
NUMBER OF CYCLES AT 60Hz
Fig. 5-MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
.1
.5
1
2
5
10
20
50
100 200
500 1000
REVERSE VOLTAGE, VOLTS
Fig. 6-TYPICAL JUNCTION CAPACITANCE
Similar pages