Aluminum Electrolytic Capacitor/TG Surface Mount Type Series: TG Type : V ■ Features Japan Endurance:125°C 1000 to 2000 h Miniaturization(40% less than TA Series) Low ESR(Low temp) Vibration-proof product is available upon request.(φ8 < =) ■ Application Corresponds to use in the car engine room. The best for an electronically controlled unit (ECU, ABS etc). ■ Specifications Category temp. range Rated W.V. Range Nominal Cap. Range Capacitance Tolerance DC Leakage Current tan δ -40 to +125°C 10 to 100 V .DC 10 to 4700 µ F ±20 % (120Hz/+20°C) I <= 0.01 CV or 3(µ A) after 2 minutes (whichever, greater) Please see the attached standard products list W.V. (V) -25 / +20 °C -40 / +20 °C Characteristics at Low Temperature 10 3 6 16 2 4 25 2 4 35 2 3 50 2 3 63 2 3 80 2 3 100 2 3 (Inpedance ratio at 120Hz) After applying rated working voltage for 1000 hours(φ8 x 6.2), 2000 hours(8x10.2 <=) at +125 ±2°C and then being stabilized at +20°C, capacitors shall meet the following limits. ±30 % of initial measured value (code U:±35%) Capacitance change < 300 % of initial specified value (code U:350%) tan δ = < initial specified value DC leakage current = After storage for 1000 hours at +125 ±2°C with no voltage applied and then being stabilized at +20°C, capacitors shall meet the limits specified in Endurance.(With voltage treatment) Endurance Shelf Life After reflow soldering ( Refer to page 20 for recommendable temperature profile.) and then being stabilized at +20°C, capacitor shall meet the following limits. Resistance to Soldering Heat Capacitance change tan δ DC leakage current ■ Marking ±10 % of initial measured value < initial specified value = < initial specified value = ■ Dimensions in mm (not to scale) ( ) reference size (P) Lot number >φ12.5) (= (I) K Series identification TG H φD±0.5 Negative polarity marking A±0.2 0.3 max Capacitance (µF) w (I) W.V. code B±0.2 <φ10) (= E~G=L±0.3 H~K=L±0.5 W.V. code Capacitance (µF) Negative polarity marking TG Series identification Lot number W.V. code V Code 10 A 16 C 25 E 35 V V Code 50 H 63 J 80 100 K 2A Size code D L A,B H max. I W P K E 8.0 6.2 8.3 9.5 F 8.0 10.2 8.3 10.0 G 10.0 10.2 10.3 12.0 3.5 0.90 ±0.2 4.6 0.70 ±0.20 H13 12.5 13.5 13.5 15.0 4.7 0.90 ±0.3 4.4 0.70 ±0.30 J16 16.0 16.5 17.0 19.0 5.5 1.20 ±0.3 6.7 0.70 ±0.30 K16 18.0 16.5 19.0 21.0 6.7 1.20 ±0.3 6.7 0.70 ±0.30 3.4 0.65 ±0.1 2.2 0.35 -0.20 to +0.15 3.4 0.90 ±0.2 3.1 0.70 ±0.20 Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail. EE74 Aluminum Electrolytic Capacitor/TG ■ Case size VS Capacitance, ESR and Ripple current Capacitance (µF) ESR;(Ω/100kHz,+20°C),Ripple current ;(mA r.m.s./100kHz+125°C) 16 25 10 W.V. (V) size ESR 20°C -40°C Ripple current size 100 F ESR 20°C -40°C Ripple current 47 100 E 20 1.0 (100) (F) 10 0.5 (10) (0.5) 197 (197) size ESR 20°C -40°C Ripple current E 1.0 20 100 (E) (1.0) (20) (100) F 0.5 10 197 (F) (0.5) (10) (197) 220 (E) F 0.5 10 197 G 0.3 6.0 270 G 0.3 6.0 270 330 (F) (0.5) (10) (197) (G) (0.3) (6.0) (270) (G) (0.3) (6.0) (270) G 0.3 6.0 270 H13 0.12 1.8 800 H13 0.12 1.8 800 470 (G) (0.3) (6.0) (270) H13 0.12 1.8 800 H13 0.12 1.8 800 H13 0.12 1.8 800 (H13) (0.12) (1.8) (800) J16 0.08 (20) (1.0) 680 1000 H13 0.12 1.8 800 1500 (H13) (0.12) (1.8) (800) 2200 J16 0.08 1.2 1100 3300 (J16) 4700 (1100) K16 0.075 1.1 K16 0.075 1.1 1300 1100 (0.12) (1.8) (800) (J16) (0.08) (1.2) (1100) J16 0.08 1.2 1100 K16 0.075 1.1 1300 (J16) (0.08) (1.2) (1100) K16 0.075 1.1 1300 K16 0.075 1.1 1300 K16 0.075 1.1 1300 35 size (µF) (1.2) 1300 W.V. (V) Capacitance (0.08) 1.2 (H13) 50 ESR 20°C -40°C Ripple current size 63 ESR 20°C -40°C Ripple current size ESR 20°C -40°C Ripple current 10 E 1.6 32 80 E 2.2 55 55 22 E 1.6 32 80 F 1 25 100 (E) (1.6) (32) (80) (F) (1) (25) (100) F 0.75 15 133 G 0.8 20 150 (15) (133) (F) (1) (25) (100) 10 221 G 0.8 20 150 33 E 1.0 20 100 (E) (1.0) (20) (100) (F) (0.75) F 0.5 10 197 G 0.5 (F) (0.5) (10) (197) (G) (0.8) (20) (150) G 0.3 6.0 270 (G) (0.5) (10) (221) H13 0.26 5.2 350 220 (G) (0.3) (6.0) (270) H13 0.23 3.4 600 H13 0.26 5.2 350 330 H13 0.12 1.8 800 H13 0.23 3.4 600 J16 0.18 3.6 500 470 (H13) (0.12) (1.8) (800) J16 0.15 2.2 900 J16 0.18 3.6 500 J16 0.08 1.2 1100 (J16) (0.08) (1.2) (1100) (J16) (0.15) (2.2) (900) K16 0.075 1.1 1300 K16 0.14 2.1 950 K16 0.075 1.1 1300 K16 0.14 2.1 950 47 100 680 1000 80 W.V. (V) Capacitance (µF) size 100 ESR 20°C -40°C Ripple current size ESR 20°C -40°C Ripple current 10 F 1.3 32 70 F 1.3 32 70 22 (F) (1.3) (32) (70) (F) (1.3) (32) (70) G 1.0 25 90 G 1.0 25 90 33 (F) (1.3) (32) (70) G 1.0 25 90 G 1.0 25 90 H13 0.42 8.4 250 J16 0.3 6.0 350 K16 0.28 5.6 400 K16 0.28 5.6 400 47 100 220 330 470 (G) (1.0) (25) (90) H13 0.42 8.4 250 (H13) (0.42) (8.4) (250) J16 0.3 6.0 350 (J16) (0.3) (6.0) (350) K16 0.28 5.6 400 (J16) (0.3) (6.0) (350) K16 0.28 5.6 400 K16 0.28 5.6 400 Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail. EE75 V . TG Aluminum Electrolytic Capacitor/TG ■ Standard Products Case Size W.V. (V) 10 Cap (±20%) (µF) Size code (mm) (mm) 8 6.2 E 220 (8) (6.2) (E) 8 10.2 F 330 (8) (10.2) (F) 10 10.2 G 470 (10) (10.2) (G) 1000 12.5 13.5 197 (197) 270 (270) 800 (800) (1100) 18 (16.5) (J16) 16.5 K16 1300 4700 18 16.5 K16 1300 100 8 10.2 F 197 (8) (10.2) (F) (197) 10 10.2 G 270 1500 (12.5) 2200 16 (16) (120Hz) (+20°C) 100 H13 tan δ ESR (100kHz) (+20°C) (Ω) (100) (13.5) (H13) J16 16.5 220 Part No. Min. Packaging Q’ty Taping (pcs) 1.0 0.30 EEVTG1A101P 1000 (1.0) 0.30 EEVTG1A221UP 1000 0.5 0.30 EEVTG1A221P 500 (0.5) 0.30 EEVTG1A331UP 500 0.3 0.30 EEVTG1A331P 500 (0.3) 0.30 EEVTG1A471UP 500 0.12 0.30 EEVTG1A102Q 200 (0.12) 0.30 EEVTG1A152UQ 200 0.08 0.32 EEVTG1A222M 125 (0.08) 0.34 EEVTG1A332UM 125 0.075 0.34 EEVTG1A332M 125 0.075 0.36 EEVTG1A472M 125 0.5 0.23 EEVTG1C101P 500 (0.5) 0.23 EEVTG1C221UP 500 0.3 0.23 EEVTG1C221P 500 1100 (10) (10.2) (G) (270) (0.3) 0.23 EEVTG1C331UP 500 12.5 13.5 H13 800 0.12 0.23 EEVTG1C331Q 200 470 12.5 13.5 H13 800 0.12 0.23 EEVTG1C471Q 200 680 12.5 13.5 H13 800 0.12 0.23 EEVTG1C681Q 200 1000 (12.5) (13.5) (H13) J16 16.5 (800) (0.12) 0.23 EEVTG1C102UQ 200 1100 0.08 0.23 EEVTG1C102M 125 (16.5) (J16) 16.5 K16 (1100) (0.08) 0.25 EEVTG1C222UM 125 1300 0.075 0.25 EEVTG1C222M 125 330 16 2200 (16) 18 3300 18 16.5 K16 1300 0.075 0.27 EEVTG1C332M 125 47 8 6.2 E 100 1.0 0.18 EEVTG1E470P 1000 100 (8) (6.2) (E) (1.0) 0.18 EEVTG1E101UP 1000 8 10.2 F 0.5 0.18 EEVTG1E101P 500 (8) (10.2) (F) (197) (0.5) 0.18 EEVTG1E221UP 500 10 10.2 G 270 0.3 0.18 EEVTG1E221P 500 (10) (10.2) (G) (270) (0.3) 0.18 EEVTG1E331UP 500 12.5 13.5 H13 800 0.12 0.18 EEVTG1E331Q 200 12.5 13.5 H13 800 0.12 0.18 EEVTG1E471Q 200 (13.5) (H13) J16 16.5 (800) (0.12) 0.18 EEVTG1E681UQ 200 1100 0.08 0.18 EEVTG1E681M 125 (16.5) (J16) 16.5 K16 (1100) (0.08) 0.18 EEVTG1E102UM 125 1300 0.075 0.18 EEVTG1E102M 125 220 330 25 470 680 (12.5) 16 1000 (16) 18 35 Length 100 3300 16 Dia. Specification Ripple current (100kHz) (+125°C) (m A ) (100) 197 2200 18 16.5 K16 1300 0.075 0.20 EEVTG1E222M 125 33 8 6.2 E 100 1.0 0.16 EEVTG1V330P 1000 47 (8) (6.2) (E) (1.0) 0.16 EEVTG1V470UP 1000 8 10.2 F 0.5 0.16 EEVTG1V470P 500 (8) (10.2) (F) (197) (0.5) 0.16 EEVTG1V101UP 500 10 10.2 G 270 0.3 0.16 EEVTG1V101P 500 220 (10) (10.2) (G) (270) (0.3) 0.16 EEVTG1V221UP 330 12.5 13.5 H13 800 0.12 0.16 100 (100) 197 EEVTG1V331Q 500 1000 The taping dimension are explained on p.42 of our Catalog. Please use it as a reference guide. Endurance : 125°C 1000 to 2000h Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail. EE76 Aluminum Electrolytic Capacitor/TG ■ Standard Products Case Size W.V. (V) 35 50 Cap (±20 %) Length Size code ESR (100kHz) (+20°C) (Ω) (120Hz) (+20°C) tan δ Part No. Min. Packaging Q’ty Taping (µF) (mm) (mm) 470 12.5 13.5 (H13) (800) (0.12) 0.16 EEVTG1V471UQ 200 16 16.5 J16 1100 0.08 0.16 EEVTG1V471M 125 (1100) (0.08) 0.16 EEVTG1V681UM 125 0.075 0.16 EEVTG1V681M 125 0.075 0.16 EEVTG1V102M 125 0.14 EEVTG1H100P 1000 680 (16) (16.5) (J16) (pcs) 18 16.5 K16 1300 1000 18 16.5 K16 1300 10 8 6.2 E 80 1.6 22 8 6.2 E 80 1.6 0.14 EEVTG1H220P 1000 33 (8) (6.2) (E) (80) (1.6) 0.14 EEVTG1H330UP 1000 8 10.2 F 133 0.75 0.14 EEVTG1H330P 500 47 (8) (10.2) (F) (133) (0.75) 0.14 EEVTG1H470UP 500 10 10.2 G 221 0.5 0.14 EEVTG1H470P 500 100 (10) (10.2) (G) (221) (0.5) 0.14 EEVTG1H101UP 500 220 12.5 13.5 H13 600 0.23 0.14 EEVTG1H221Q 200 330 12.5 13.5 H13 600 0.23 0.14 EEVTG1H331Q 200 470 16 16.5 J16 900 0.15 0.14 EEVTG1H471M 125 680 (16) (0.15) 0.14 EEVTG1H681UM 125 18 16.5 K16 950 0.14 0.14 EEVTG1H681M 125 1000 18 16.5 K16 950 0.14 0.14 EEVTG1H102M 125 10 8 6.2 E 55 2.2 0.12 EEVTG1J100P 1000 (16.5) (J16) (900) 1 0.12 EEVTG1J220P 500 (100) (1) 0.12 EEVTG1J330UP 500 G 150 0.8 0.12 EEVTG1J330P 500 (F) (100) (1) 0.12 EEVTG1J470UP 500 22 8 10.2 F 33 (8) (10.2) (F) 10 10.2 47 (8) (10.2) 10 10.2 G 150 100 (10) (10.2) (G) 12.5 13.5 H13 63 100 0.8 0.12 EEVTG1J470P 500 (150) (0.8) 0.12 EEVTG1J101UP 500 350 0.26 0.12 EEVTG1J101Q 200 0.12 EEVTG1J221Q 200 220 12.5 13.5 H13 350 0.26 330 16 16.5 J16 500 0.18 0.12 EEVTG1J331M 125 470 16 16.5 J16 500 0.18 0.12 EEVTG1J471M 125 10 8 10.2 F 70 1.3 0.12 EEVTG1K100P 500 (1.3) 0.12 EEVTG1K220UP 500 1.0 0.12 EEVTG1K220P 500 (1.3) 0.12 EEVTG1K330UP 500 1.0 0.12 EEVTG1K330P 500 22 33 47 80 Dia. Specification Ripple current (100kHz) (+125°C) (m A ) 100 (8) (10.2) (F) (70) 10 10.2 G 90 (8) (10.2) (F) (70) 10 10.2 G 90 (10) (10.2) (G) (90) (1.0) 0.12 EEVTG1K470UP 500 12.5 13.5 H13 250 0.42 0.12 EEVTG1K470Q 200 (0.42) 0.12 EEVTG1K101UQ 200 0.3 0.12 EEVTG1K101M 125 (12.5) 16 220 (16) 18 330 470 (13.5) (H13) 16.5 J16 (250) 350 (350) (0.3) 0.12 EEVTG1K221UM 125 K16 400 0.28 0.12 EEVTG1K221M 125 (16.5) (J16) (16.5) (J16) 16.5 (350) (0.3) 0.12 EEVTG1K331UM 125 18 16.5 K16 400 0.28 0.12 EEVTG1K331M 125 18 16.5 K16 400 0.28 0.12 EEVTG1K471M 125 (16) The taping dimension are explained on p.42 of our Catalog. Please use it as a reference guide. Endurance : 125°C 1000 to 2000h Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail. EE77 V . TG Aluminum Electrolytic Capacitor/TG ■ Standard Products Case Size W.V. (V) 100 Cap (±20 %) (µF) Dia. Length Specification Size code (mm) (mm) 10 8 22 (8) 10 Ripple current (100kHz) (+125°C) (m A ) tan δ ESR (100kHz) (+20°C) (Ω) (120Hz) (+20°C) Part No. Min. Packaging Q’ty Taping (pcs) F 70 1.3 0.1 EEVTG2A100P 500 (10.2) (F) (70) (1.3) 0.1 EEVTG2A220UP 500 10.2 G 90 1.0 0.1 EEVTG2A220P 500 1.0 0.1 EEVTG2A330P 500 10.2 33 10 10.2 G 90 13.5 H13 250 0.42 0.1 EEVTG2A470Q 200 0.3 0.1 EEVTG2A101M 125 47 12.5 100 16 16.5 J16 350 220 18 16.5 K16 400 0.28 0.1 EEVTG2A221M 125 330 18 16.5 K16 400 0.28 0.1 EEVTG2A331M 125 The taping dimension are explained on p.42 of our Catalog. Please use it as a reference guide. Endurance : 125°C 1000 to 2000h Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail. EE78