PulseCore ASM3I623S01BG-08-TT Timing-safeâ ¢ peak emi reduction ic Datasheet

ASM3P623S01B/C/J
May 2007
rev 0.4
Timing-Safe™ Peak EMI reduction IC
General Features
•
available in 8pin package. The ASM3P623S01J is the
eight-pin version with crystal interface and accepts one
•
Clock distribution with Timing-Safe™ Peak EMI
Reduction
Input frequency range: 20MHz - 50MHz
•
Zero input - output propagation delay
All parts have on-chip PLLs that lock to an input clock on
•
Low-skew outputs
the CLKIN pin. The PLL feedback is on-chip and is
•
Output-output skew less than 250pS
obtained from the CLKOUT pad, internal to the device.
•
Device-device skew less than 700pS
reference input and drives out two low-skew clocks.
•
Less than 200pS cycle-to-cycle jitter
Multiple ASM3P623S01B/C/J devices can accept the same
•
Available in 8pin, 150 mil SOIC, 4.4mm TSSOP
input clock and distribute it. In this case, the skew between
Packages (ASM3P623S00B/C/J)
the outputs of the two devices is guaranteed to be less than
•
3.3V operation
700pS.
•
Industrial temperature range
•
•
Advanced 0.35µ CMOS technology
The First True Drop-in Solution
All outputs have less than 200pS of cycle-to-cycle jitter.
The input and output propagation delay is guaranteed to be
less than 250pS, and the output-to-output skew is
guaranteed to be less than 250pS.
Functional Description
ASM3P623S01B/C/J is a versatile, 3.3V zero-delay buffer
designed to distribute high-speed Timing-Safe™ clocks
with Peak EMI reduction. ASM3P623S01B/C accepts one
Refer “Spread Spectrum Control and Input-Output Skew
Table”
for
deviations
and
Input-Output
Skew for
ASM3P623S01B/C/J devices
reference input and drives out three low-skew clocks. It is
Block Diagram
VDD
SSON
SS%
PLL
Modulation
XIN/CLKIN
XOUT
Crystal
Oscillator
Reference
Divider
Feedback
Divider
Phase
Detector
Loop
Filter
VCO
Feedforward
Divider
GND
PulseCore Semiconductor Corporation
1715 S. Bascom Ave Suite 200 Campbell, CA 95008 • Tel: 408-879-9077 • Fax: 408-879-9018
www.pulsecoresemi.com
Notice: The information in this document is subject to change without notice.
CLKOUT
ASM3P623S01B/C/J
May 2007
rev 0.4
Spread Spectrum Frequency Generation
The clocks in digital systems are typically square waves
PCBs etc. These methods are expensive. Spread
with a 50% duty cycle and as frequencies increase the
spectrum clocking reduces the peak energy by reducing
edge rates also get faster. Analysis shows that a square
the Q factor of the clock. This is done by slowly
wave is composed of fundamental frequency and
modulating
harmonics. The fundamental frequency and harmonics
ASM3P623S01B/C/J uses the center modulation spread
generate the energy peaks that become the source of
spectrum technique in which the modulated output
EMI. Regulatory agencies test electronic equipment by
frequency varies above and below the reference
measuring the amount of peak energy radiated from the
frequency with a specified modulation rate. With center
equipment. In fact, the peak level allowed decreases as
modulation, the average frequency is the same as the
the frequency increases. The standard methods of
unmodulated frequency and there is no performance
reducing EMI are to use shielding, filtering, multi-layer
degradation
the
clock
frequency.
Timing-Safe™ technology
Timing-Safe™ technology is the ability to modulate a
clock source with Spread Spectrum technology and
maintain synchronization with any associated data path.
Pin Configuration
CLKIN
1
8
CLKOUT
7
VDD
SS% 3
6
CLKOUT2
GND 4
5
SSON
8
CLKOUT
7
VDD
SS% 3
6
CLKOUT1
GND 4
5
SSON
CLKOUT1 2
XIN/CLKIN
ASM3P623S01B/C
1
XOUT 2
ASM3P623S01J
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
2 of 12
The
ASM3P623S01B/C/J
May 2007
rev 0.4
Pin Description for ASM3P623S01B/C
Pin #
Pin Name
1
CLKIN
2
Description
Input reference frequency, 5V-tolerant input
CLKOUT
2
3
Buffered clock output
3
SS%
Spread Spectrum Selection
4
GND
Ground
5
SSON3
6
CLKOUT2
7
VDD
8
CLKOUT
Spread Spectrum enable and disable option When SSON is HIGH, the spread
spectrum is enabled and when LOW, it turns off the spread spectrum.
Buffered clock output
3.3V supply
1,2
Buffered clock output
Notes:
1. This output is driven and has an internal feedback for the PLL.
2. Weak pull-down on all outputs. 3. Weak pull-up on these inputs
4. Buffered clock outputs are Timing-Safe™
Pin Description for ASM3P623S01J
Pin #
1
Pin Name
XIN/CLKIN
Description
Crystal connection or external reference frequency input. This pin has dual functions. It
2
XOUT
can be connected either to an external crystal or an external reference clock.
Crystal connection. If using an external reference, this pin must be left unconnected.
3
SS%2
Spread Spectrum Selection
4
GND
Ground
5
SSON2
6
CLKOUT1
7
VDD
8
CLKOUT
Spread Spectrum enable and disable option When SSON is HIGH, the spread
spectrum is enabled and when LOW, it turns off the spread spectrum.
Buffered clock output
3.3V supply
1,3
Buffered clock output
Notes:
1. Weak pull-down on all outputs. 2. Weak pull-up on these inputs
3. This output is driven and has an internal feedback for the PLL.
4. Buffered clock outputs are Timing-Safe™
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
3 of 12
ASM3P623S01B/C/J
May 2007
rev 0.4
Spread Spectrum Control and Input-Output Skew Table
(Note: The values given in the table are for an input frequency of 32 MHz)
Device
ASM3P623S01B
ASM3P623S01C
ASM3P623S01J
SS%
Deviation
Input-Output Skew(±TSKEW)
0
±0.25 %
0.125
1
±0.5 %
0.25
0
±.125 %
0.125
1
±0.25 %
0.25
0
±0.125 %
0.125
1
±0.25 %
0.25
Note: TSKEW is measured in units of the Clock Period
Absolute Maximum Rating
Symbol
Parameter
Rating
Unit
VDD
Voltage on any pin with respect to Ground
-0.5 to +4.6
V
TSTG
Storage temperature
-65 to +125
°C
Ts
Max. Soldering Temperature (10 sec)
260
°C
TJ
Junction Temperature
150
°C
TDV
Static Discharge Voltage (As per JEDEC STD22- A114-B)
2
KV
Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability.
Operating Conditions for ASM3P623S01B/C/J Devices
Parameter
Min
Max
Unit
Supply Voltage
3.0
3.6
V
TA
Operating Temperature (Ambient Temperature)
-40
+85
°C
CL
Load Capacitance
30
pF
CIN
Input Capacitance
7
pF
VDD
Description
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
4 of 12
ASM3P623S01B/C/J
May 2007
rev 0.4
Electrical Characteristics for ASM3P623S01B/C/J
Parameter
VIL
Description
5
Input HIGH Voltage
IIL
Input LOW Current
IIH
Min
Typ
Input LOW Voltage
VIH
VOL
Test Conditions
5
Max
Unit
0.8
V
2.0
V
VIN = 0V
50
µA
Input HIGH Current
VIN = VDD
100
µA
Output LOW Voltage6
IOL = 8mA
0.4
V
6
VOH
Output HIGH Voltage
IOH = -8mA
2.4
IDD
Supply Current
Unloaded outputs
Zo
Output Impedance
V
15
mA
23
Ω
Switching Characteristics for ASM3P623S01B/C/J7
Parameter
1/t1
Description
Test Conditions
Output Frequency
6
Duty Cycle = (t2 / t1) * 100
t3
t4
t5
t6
Output Rise Time
Output Fall Time
6
6
Output-to-output skew
6
Delay, CLKIN Rising Edge to
CLKOUT Rising Edge
Device-to-Device Skew 6
tJ
Cycle-to-cycle jitter 6
PLL Lock Time 6
Max
Unit
50
MHz
60
%
Measured between 0.8V and 2.0V
2.5
nS
Measured between 2.0V and 0.8V
2.5
nS
All outputs equally loaded
250
pS
±350
pS
700
pS
200
pS
1.0
mS
30pF load
20
Measured at VDD/2
40
Measured at VDD /2
6
t7
tLOCK
Min
Measured at VDD/2 on the CLKOUT pins
of the device
Loaded outputs
Stable power supply, valid clock presented
on CLKIN pin
Typ
50
Notes:
5. CLKIN input has a threshold voltage of VDD/2
6. Parameter is guaranteed by design and characterization. Not 100% tested in production
7. All parameters specified with loaded outputs.
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
5 of 12
ASM3P623S01B/C/J
May 2007
rev 0.4
Switching Waveforms
Duty Cycle Timing
t1
t2
1.4 V
1.4 V
1.4 V
All Outputs Rise/Fall Time
2.0 V
0.8 V
OUTPUT
2.0 V
0.8 V
3.3 V
0V
t4
t3
Output - Output Skew
1.4 V
O UTPUT
1.4 V
O UTPUT
t5
Input - Output Propagation Delay
VDD /2
INPUT
VDD /2
OUTPUT
t6
Device - Device Skew
CLKOUT, Device 1
VDD /2
VDD /2
CLKOUT, Device 2
t7
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
6 of 12
ASM3P623S01B/C/J
May 2007
rev 0.4
Input-Output Skew
Test Circuit
Input
Timing-Safe™
Output
+3.3V
TSKEW -
OUTPUT
TSKEW+
VDD
CLKOUT
CLOAD
0.1uF
GND
One clock cycle
N=1
TSKEW represents input-output skew
when spread spectrum is ON
For example, TSKEW = ± 0.125 for an
Input clock 32MHz, translates in to
(1/32MHz) * 0.125=3.90nS
A Typical example of Timing-Safe™ waveform
Input
Input
CLKOUT with SSOFF
Timing-Safe™ CLKOUT
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
7 of 12
ASM3P623S01B/C/J
May 2007
rev 0.4
Package Information
8-lead SOIC Package(150-mil)
H
E
D
A2
A
C
A1
D
θ
e
L
B
Dimensions
Symbol
Inches
Min
Max
Millimeters
Min
Max
A1
0.004
0.010
0.10
0.25
A
0.053
0.069
1.35
1.75
A2
0.049
0.059
1.25
1.50
B
0.012
0.020
0.31
0.51
C
0.007
0.010
0.18
0.25
D
0.193 BSC
4.90 BSC
E
0.154 BSC
3.91 BSC
e
0.050 BSC
1.27 BSC
H
0.236 BSC
6.00 BSC
L
0.016
0.050
0.41
1.27
θ
0°
8°
0°
8°
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
8 of 12
ASM3P623S01B/C/J
May 2007
rev 0.4
8-lead TSSOP Package(4.40-MM Body)
H
E
D
A2
A
C
θ
e
A1
L
B
Dimensions
Symbol
Inches
Min
Millimeters
Max
A
Min
Max
0.043
1.10
A1
0.002
0.006
0.05
0.15
A2
0.033
0.037
0.85
0.95
B
0.008
0.012
0.19
0.30
c
0.004
0.008
0.09
0.20
D
0.114
0.122
2.90
3.10
E
0.169
0.177
4.30
4.50
e
0.026 BSC
0.65 BSC
H
0.252 BSC
6.40 BSC
L
0.020
0.028
0.50
0.70
θ
0°
8°
0°
8°
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
9 of 12
ASM3P623S01B/C/J
May 2007
rev 0.4
Ordering Codes
Ordering Code
Marking
Package Type
Temperature
ASM3P623S01BF-08-ST
3P623S01BF
8-pin 150-mil SOIC- TUBE, Pb Free
Commercial
ASM3I623S01BF-08-ST
3I623S01BF
8-pin 150-mil SOIC- TUBE, Pb Free
Industrial
ASM3P623S01BF-08-SR
3P623S01BF
8-pin 150-mil SOIC-TAPE & REEL, Pb Free
Commercial
ASM3I623S01BF-08-SR
3I623S01BF
8-pin 150-mil SOIC-TAPE & REEL, Pb Free
Industrial
ASM3P623S01BF-08-TT
3P623S01BF
8-pin 4.4-mm TSSOP - TUBE, Pb Free
Commercial
ASM3I623S01BF-08-TT
3I623S01BF
8-pin 4.4-mm TSSOP - TUBE, Pb Free
Industrial
ASM3P623S01BF-08-TR
3P623S01BF
8- pin 4.4-mm TSSOP - TAPE & REEL, Pb Free
Commercial
ASM3I623S01BF-08-TR
3I623S01BF
8-pin 4.4-mm TSSOP - TAPE & REEL, Pb Free
Industrial
ASM3P623S01BG-08-ST
3P623S01BG
8-pin 150-mil SOIC- TUBE, Green
Commercial
ASM3I623S01BG-08-ST
3I623S01BG
8-pin 150-mil SOIC- TUBE, Green
Industrial
ASM3P623S01BG-08-SR
3P623S01BG
8-pin 150-mil SOIC-TAPE & REEL, Green
Commercial
ASM3I623S01BG-08-SR
3I623S01BG
8-pin 150-mil SOIC-TAPE & REEL, Green
Industrial
ASM3P623S01BG-08-TT
3P623S01BG
8-pin 4.4-mm TSSOP - TUBE, Green
Commercial
ASM3I623S01BG-08-TT
3I623S01BG
8-pin 4.4-mm TSSOP - TUBE, Green
Industrial
ASM3P623S01BG-08-TR
3P623S01BG
8- pin 4.4-mm TSSOP - TAPE & REEL, Green
Commercial
ASM3I623S01BG-08-TR
3I623S01BG
8-pin 4.4-mm TSSOP - TAPE & REEL, Green
Industrial
ASM3P623S01CF-08-ST
3P623S01CF
8-pin 150-mil SOIC- TUBE, Pb Free
Commercial
ASM3I623S01CF-08-ST
3I623S01CF
8-pin 150-mil SOIC- TUBE, Pb Free
Industrial
ASM3P623S01CF-08-SR
3P623S01CF
8-pin 150-mil SOIC-TAPE & REEL, Pb Free
Commercial
ASM3I623S01CF-08-SR
3I623S01CF
8-pin 150-mil SOIC-TAPE & REEL, Pb Free
Industrial
ASM3P623S01CF-08-TT
3P623S01CF
8-pin 4.4-mm TSSOP - TUBE, Pb Free
Commercial
ASM3I623S01CF-08-TT
3I623S01CF
8-pin 4.4-mm TSSOP - TUBE, Pb Free
Industrial
ASM3P623S01CF-08-TR
3P623S01CF
8- pin 4.4-mm TSSOP - TAPE & REEL, Pb Free
Commercial
ASM3I623S01CF-08-TR
3I623S01CF
8-pin 4.4-mm TSSOP - TAPE & REEL, Pb Free
Industrial
ASM3P623S01CG-08-ST
3P623S01CG
8-pin 150-mil SOIC- TUBE, Green
Commercial
ASM3I623S01CG-08-ST
3I623S01CG
8-pin 150-mil SOIC- TUBE, Green
Industrial
ASM3P623S01CG-08-SR
3P623S01CG
8-pin 150-mil SOIC-TAPE & REEL, Green
Commercial
ASM3I623S01CG-08-SR
3I623S01CG
8-pin 150-mil SOIC-TAPE & REEL, Green
Industrial
ASM3P623S01CG-08-TT
3P623S01CG
8-pin 4.4-mm TSSOP - TUBE, Green
Commercial
ASM3I623S01CG-08-TT
3I623S01CG
8-pin 4.4-mm TSSOP - TUBE, Green
Industrial
ASM3P623S01CG-08-TR
3P623S01CG
8- pin 4.4-mm TSSOP - TAPE & REEL, Green
Commercial
ASM3I623S01CG-08-TR
3I623S01CG
8-pin 4.4-mm TSSOP - TAPE & REEL, Green
Industrial
ASM3P623S01JF-08-ST
3P623S01JF
8-pin 150-mil SOIC- TUBE, Pb Free
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
Commercial
10 of 12
ASM3P623S01B/C/J
May 2007
rev 0.4
Ordering Codes (Cont’d)
Ordering Code
Marking
Package Type
Temperature
Industrial
ASM3I623S01JF-08-ST
3I623S01JF
8-pin 150-mil SOIC- TUBE, Pb Free
ASM3P623S01JF-08-SR
3P623S01JF
8-pin 150-mil SOIC-TAPE & REEL, Pb Free
Commercial
ASM3I623S01JF-08-SR
3I623S01JF
8-pin 150-mil SOIC-TAPE & REEL, Pb Free
Industrial
ASM3P623S01JF-08-TT
3P623S01JF
8-pin 4.4-mm TSSOP - TUBE, Pb Free
Commercial
ASM3I623S01JF-08-TT
3I623S01JF
8-pin 4.4-mm TSSOP - TUBE, Pb Free
Industrial
ASM3P623S01JF-08-TR
3P623S01JF
8- pin 4.4-mm TSSOP - TAPE & REEL, Pb Free
Commercial
ASM3I623S01JF-08-TR
3I623S01JF
8-pin 4.4-mm TSSOP - TAPE & REEL, Pb Free
Industrial
ASM3P623S01JG-08-ST
3P623S01JG
8-pin 150-mil SOIC- TUBE, Green
Commercial
ASM3I623S01JG-08-ST
3I623S01JG
8-pin 150-mil SOIC- TUBE, Green
Industrial
ASM3P623S01JG-08-SR
3P623S01JG
8-pin 150-mil SOIC-TAPE & REEL, Green
Commercial
ASM3I623S01JG-08-SR
3I623S01JG
8-pin 150-mil SOIC-TAPE & REEL, Green
Industrial
ASM3P623S01JG-08-TT
3P623S01JG
8-pin 4.4-mm TSSOP - TUBE, Green
Commercial
ASM3I623S01JG-08-TT
3I623S01JG
8-pin 4.4-mm TSSOP - TUBE, Green
Industrial
ASM3P623S01JG-08-TR
3P623S01JG
8- pin 4.4-mm TSSOP - TAPE & REEL, Green
Commercial
ASM3I623S01JG-08-TR
3I623S01JG
8-pin 4.4-mm TSSOP - TAPE & REEL, Green
Industrial
Device Ordering Information
A S M 3 P 6 2 3 S 0 1 B F - 0 8 - T R
R = Tape & Reel, T = Tube or Tray
O = SOT
S = SOIC
T = TSSOP
A = SSOP
V = TVSOP
B = BGA
Q = QFN
U = MSOP
E = TQFP
L = LQFP
U = MSOP
P = PDIP
D = QSOP
X = SC-70
DEVICE PIN COUNT
F = LEAD FREE AND RoHS COMPLIANT PART
G = GREEN PACKAGE, LEAD FREE, and RoHS
PART NUMBER
X= Automotive
I= Industrial
P or n/c = Commercial
(-40C to +125C) (-40C to +85C)
(0C to +70C)
1 = Reserved
2 = Non PLL based
3 = EMI Reduction
4 = DDR support products
5 = STD Zero Delay Buffer
6 = Power Management
7 = Power Management
8 = Power Management
9 = Hi Performance
0 = Reserved
PulseCore Semiconductor Mixed Signal Product
Licensed under US patent #5,488,627, #6,646,463 and #5,631,920.
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
11 of 12
ASM3P623S01B/C/J
May 2007
rev 0.4
PulseCore Semiconductor Corporation
1715 S. Bascom Ave Suite 200
Campbell, CA 95008
Tel: 408-879-9077
Fax: 408-879-9018
www.pulsecoresemi.com
Copyright © PulseCore Semiconductor
All Rights Reserved
Part Number: ASM3P623S00B/C/J
Document Version: 0.4
Note: This product utilizes US Patent # 6,646,463 Impedance Emulator Patent issued to PulseCore Semiconductor, dated 11-11-2003
Timing-Safe™ US Patent Pending.
© Copyright 2006 PulseCore Semiconductor Corporation. All rights reserved. Our logo and name are trademarks or
registered trademarks of PulseCore Semiconductor. All other brand and product names may be the trademarks of their
respective companies. PulseCore reserves the right to make changes to this document and its products at any time without
notice. PulseCore assumes no responsibility for any errors that may appear in this document. The data contained herein
represents PulseCore’s best data and/or estimates at the time of issuance. PulseCore reserves the right to change or
correct this data at any time, without notice. If the product described herein is under development, significant changes to
these specifications are possible. The information in this product data sheet is intended to be general descriptive information
for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or
customer. PulseCore does not assume any responsibility or liability arising out of the application or use of any product
described herein, and disclaims any express or implied warranties related to the sale and/or use of PulseCore products
including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual
property rights, except as express agreed to in PulseCore’s Terms and Conditions of Sale (which are available from
PulseCore). All sales of PulseCore products are made exclusively according to PulseCore’s Terms and Conditions of Sale.
The purchase of products from PulseCore does not convey a license under any patent rights, copyrights; mask works rights,
trademarks, or any other intellectual property rights of PulseCore or third parties. PulseCore does not authorize its products
for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result
in significant injury to the user, and the inclusion of PulseCore products in such life-supporting systems implies that the
manufacturer assumes all risk of such use and agrees to indemnify PulseCore against all claims arising from such use.
Timing-Safe™ Peak EMI Reduction IC
Notice: The information in this document is subject to change without notice.
12 of 12
Similar pages