ADVANCED INFORMATION ADVANCED INFORMATION ADVANCED INFORMATION BY229X SERIES FAST SWITCHING PLASTIC RECTIFIER Reverse Voltage - 50 to 600 Volts Forward Current - 8.0 Amperes ITO-220AC FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Glass passivated chip junction ♦ Low leakage, high voltage ♦ High surge current capability ♦ Superfast recovery time, for high efficiency ♦ High temperature soldering guaranteed: 250°C, 0.25" (6.35mm) from case for 10 seconds 0.188 (4.77) 0.172 (4.36) 0.405 (10.27) 0.383 (9.72) 0.110 (2.80) 0.100 (2.54) 0.131 (3.39) DIA. 0.122 (3.08) 0.140 (3.56) DIA. 0.130 (3.30) 0.600 (15.5) 0.580 (14.5) 0.676 (17.2) 0.646 (16.4) PIN 1 0.350 (8.89) 0.330 (8.38) 2 MECHANICAL DATA 0.191 (4.85) 0.171 (4.35) 0.560 (14.22) 0.530 (13.46) Case: JEDEC ITO-220AC fully overmolded plastic body over passivated chip Terminals: Plated lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.064 ounce, 1.81 grams Mounting Torque: 5 in. - lbs. max. 0.110 (2.80) 0.100 (2.54) 0.060 (1.52) 0.037 (0.94) 0.027 (0.69) 0.022 (0.55) 0.014 (0.36) 0.205 (5.20) 0.195 (4.95) PIN 1 PIN 2 Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS BY229X -200 BY229X -400 BY229X -600 BY229X -800 UNITS Maximum recurrent peak reverse voltage VRRM 200 400 600 800 Volts Maximum RMS voltage VRMS 140 280 420 560 Volts Maximum DC blocking voltage VDC 200 400 600 800 Volts Maximum average forward rectified current at TC=100°C I(AV) 8.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 100 Amps VF 1.85 Volts IR 10.0 300 µA Maximum reverse recovery time (NOTE 1) trr 145 ns Maximum recovered stored charge (NOTE 2) Qrr 700 nC Maximum slope of reverse recovery current (NOTE 2) dir/dt 60 A/µs Maximum thermal resistance (NOTE 3) RΘJC 4.8 °C/W Typical thermal resistance, junction to air RΘJA 20 °C/W TJ, TSTG -40 to +150 °C VISOL 4500 (NOTE 4) 3500 (NOTE 5) 1500 (NOTE 6) Volts Maximum instantaneous forward voltage at 20A Maximum DC reverse current at rated DC blocking voltage TJ=25°C at TJ=125°C Operating junction and storage temperature range RMS Isolation voltage from terminals to heatsink with RH ≤ 30% NOTES: (1) Reverse recovery test conditions: IF=1A, VR=30V, di/dt=50A/µs, Irr=10% IRM (2) Qrr test conditions: IF=2A, VR=30V, di/dt=20A/µs (3) Thermal resistance from junction to case mounted on heatsink with heatsink compound (4) Clip mounting, where lead does not overlap heatsink with 0.110” offset. (5) Clip mounting, where leads do overlap heatsink. (6) Screw mounting, where washer diameter is ≤ 4.9 mm (0.19”). 10/12/98 RATINGS AND CHARACTERISTIC CURVES BY229X SERIES FIG. 1 - MAXIMUM FORWARD CURRENT DERATING CURVES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 10 150 RESISTIVE OR INDUCTIVE LOAD TL=75°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 125 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 12 8 6 4 2 100 75 50 25 0 0 50 100 150 0 CASE AMBIENT TEMPERATURE, °C 100 10 1 NUMBER OF CYCLES AT 60 HZ FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS 1000 TJ=150°C TJ=150°C 10 TJ=25°C 1 TJ=100°C TJ=125°C 0.1 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 100 TJ=125°C 10 TJ=100°C 1 TJ=25°C 0.10 0.01 100 0 20 40 60 80 Cj / pF PERCENT OF RATED PEAK REVERSE VOLTAGE, % 10 1 10 VR / V 100 100