ARF466FL D G ARF466FL S RF POWER MOSFETs N - CHANNEL ENHANCEMENT MODE 200V 300W 45MHz The ARF466FL is a rugged high voltage RF power transistor designed for scientific, commercial, medical and industrial RF power amplifier applications up to 45 MHz. It has been optimized for both linear and high efficiency classes of operation. • Specified 150 Volt, 40.68 MHz Characteristics: • Output Power = 300 Watts. • Gain = 16dB (Class AB) • Efficiency = 75% (Class C) • Low Cost Flangeless RF Package. • Low Vth thermal coefficient. • Low Thermal Resistance. • Optimized SOA for Superior Ruggedness. MAXIMUM RATINGS Symbol All Ratings: TC = 25°C unless otherwise specified. Parameter ARF466FL VDSS Drain-Source Voltage 1000 VDGO Drain-Gate Voltage 1000 ID Continuous Drain Current @ TC = 25°C UNIT Volts 13 Amps VGS Gate-Source Voltage ±30 Volts PD Total Power Dissipation @ TC = 25°C 450 Watts Junction to Case 0.30 °C/W RθJC TJ,TSTG TL -55 to 175 Operating and Storage Junction Temperature Range °C 300 Lead Temperature: 0.063" from Case for 10 Sec. STATIC ELECTRICAL CHARACTERISTICS BVDSS Drain-Source Breakdown Voltage (VGS = 0V, ID = 250 µA) 1000 RDS(ON) Drain-Source On-State Resistance IDSS 1 MAX 0.90 Zero Gate Voltage Drain Current (VDS = 1000V, VGS = 0V) 25 Zero Gate Voltage Drain Current (VDS = 800V, VGS = 0V, TC = 125°C) 250 Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) g fs Forward Transconductance (VDS = 25V, ID = 6.5A) Gate Threshold Voltage (VDS = VGS, ID = 1mA) 3.3 ohms µA ±100 nA 9 mhos 4 Volts 7 2 CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. APT Website - http://www.advancedpower.com UNIT Volts (VGS = 10V, ID = 6.5A) IGSS VGS(TH) TYP 2-2006 MIN 050-4928 Rev A Characteristic / Test Conditions Symbol DYNAMIC CHARACTERISTICS Symbol ARF466FL Test Conditions Characteristic Ciss Input Capacitance Coss Output Capacitance Crss Reverse Transfer Capacitance td(on) Turn-on Delay Time tr td(off) tf MIN Turn-off Delay Time Fall Time UNIT MAX 2000 VGS = 0V Rise Time TYP VDS = 150V 165 f = 1 MHz 75 VGS = 15V 12 VDD = 500 V 10 ID = 13A @ 25°C 43 RG = 1.6Ω 10 pF ns FUNCTIONAL CHARACTERISTICS Symbol GPS Characteristic Common Source Amplifier Power Gain Test Conditions MIN TYP f = 40.68 MHz 14 16 dB 70 75 % VGS = 2.5V η Drain Efficiency ψ Electrical Ruggedness VSWR 10:1 VDD = 150V Pout = 300W MAX UNIT No Degradation in Output Power 1 Pulse Test: Pulse width < 380µS, Duty Cycle < 2% APT Reserves the right to change, without notice, the specifications and information contained herein. 10,000 30 Class C VDD = 150V 25 Pout = 150W CAPACITANCE (pf) Ciss GAIN (dB) 20 15 10 1000 500 Coss 100 Crss 50 5 0 30 45 60 75 90 105 FREQUENCY (MHz) Figure 1, Typical Gain vs Frequency 10 .1 1 10 100 200 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) Figure 2, Typical Capacitance vs. Drain-to-Source Voltage 120 52 050-4928 Rev A ID, DRAIN CURRENT (AMPERES) 2-2006 18 16 VDS> ID (ON) x RDS (ON)MAX. 250µSEC. PULSE TEST @ <0.5 % DUTY CYCLE TJ = -55°C 14 12 10 8 6 4 2 0 TJ = -55°C TJ = +25°C TJ = +125°C 0 1 2 3 4 5 6 7 8 VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) Figure 3, Typical Transfer Characteristics ID, DRAIN CURRENT (AMPERES) 20 OPERATION HERE LIMITED BY RDS (ON) 100uS 10 5 1mS 1 10mS .5 .1 TC =+25°C TJ =+175°C SINGLE PULSE 1 10 100 1000 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) Figure 4, Typical Maximum Safe Operating Area 100mS TYPICAL PERFORMANCE CURVES VGS=15 & 10V 1.05 ID, DRAIN CURRENT (AMPERES) VGS(th), THRESHOLD VOLTAGE (NORMALIZED) ARF466FL 25 1.10 1.00 0.95 0.90 0.85 0.80 20 8V 15 6V 10 5.5V 5V 5 4.5V 4V 0.75 -50 0 -25 0 25 50 75 100 125 150 TC, CASE TEMPERATURE (°C) Figure 5, Typical Threshold Voltage vs Temperature 0 5 10 15 20 25 30 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) Figure 6, Typical Output Characteristics 0.30 D = 0.9 0.25 0.7 0.20 0.5 0.15 0.10 0.3 0.05 0.1 Note: PDM t1 t2 Duty Factor D = t1/t 2 Peak TJ = PDM x ZθJC + TC 0.05 10-5 10-4 10-3 10-2 10-1 1.0 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 7a, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION Junction temp. (°C) Power (watts) RC MODEL 0.108 0.00872 0.146 0.0650 0.0460 0.767 Case temperature. (°C) Figure 7b, TRANSIENT THERMAL IMPEDANCE MODEL Table 1 - Typical Class AB Large Signal Input - Output Impedance Freq. (MHz) 2.0 13.5 27.1 40.7 65 ZIN (Ω) ZOL (Ω) 18 - j 11 1.3 - j 5 .40 - j 2.6 .20 - j 1.6 .11 + j 0.6 30 - j 1.7 25.7 - j 9.8 18 - j 13.3 12 - j 12.6 6.2 - j 8.9 Zin - Gate shunted with 25Ω IDQ = 100mA ZOL - Conjugate of optimum load for 300 W output at Vdd = 150V 2-2006 0 SINGLE PULSE 050-4928 Rev A Z JC, THERMAL IMPEDANCE (°C/W) θ 0.35 ARF466FL 40.68 MHz Test Circuit L4 Bias + 0-12V RF Input + 150V - R1 C8 C7 R3 C6 L3 R2 RF Output C9 C2 R4 L1 TL1 C3 C1 L2 ARF466FL R5 L1 -- 3t #22 AWG .25"ID .25 "L ~55nH L2 -- 5t #16 AWG .312" ID .35"L ~176nH L3 -- 10t #24 AWG .25"ID ~.5uH L4 -- VK200-4B ferrite choke 3uH C1 -- 2200pF ATC 700B C2-C5 -- Arco 465 Mica trimmer C6-C8 -- .1mF 500V ceramic chip C9 -- 3x 2200pF 500V chips COG C5 C4 R1- R3 -- 1kΩ 0.5W R4- R5 -- 1Ω 1W SMT TL1 -- 40Ω t-line 0.15 x 2" C1 is ~1.75" from R4-5. T3 Package Outline .125R 4 pls S D S ARF466FL .375 .125dia 4 pls .320 .570 1.250 .330 .100 .100 .210 S G S 1.500 .210 .300 Thermal Considerations and Package Mounting: The rated power dissipation is only available when the package mounting surface is at 25°C and the junction temperature is 175°C. The thermal resistance between junctions and case mounting surface is 0.3°C/W. When installed, an additional thermal impedance of 0.1°C/W between the package base and the mounting surface is typical. Insure that the mounting surface is smooth and flat. Thermal joint compound must be used to reduce the effects of small surface irregularities. Use the minimum amount necessary to coat the surface. The heatsink should incorporate a copper heat spreader to obtain best results. The package design clamps the ceramic base to the heatsink. A clamped joint maintains the required mounting pressure while allowing for thermal expansion of both the base and the heat sink. Four 4-40 (M3) screws provide the required mounting force. Torque the mounting screws to 6 in-lb (0.68 N-m). 050-4928 Rev A 2-2006 .005 .040 .200 APT’s products are covered by one or more of U.S.patents 4,895,810 5,045,903 5,089,434 5,182,234 5,019,522 5,262,336 6,503,786 5,256,583 4,748,103 5,283,202 5,231,474 5,434,095 5,528,058 6,939,743 and foreign patents. US and Foreign patents pending. All Rights Reserved.