CDIL BC308C Silicon planar epitaxial transistor Datasheet

Continental Device India Limited
An ISO/TS 16949, ISO 9001 and ISO 14001 Certified Company
SILICON PLANAR EPITAXIAL TRANSISTORS
BC 307, A, B, C
BC 308, A, B, C
BC 309, A, B, C
TO-92
Plastic Package
General Purpose Transistors Deisgned For Small Signal Amplification
From DC To Low Radio Frequencies
ABSOLUTE MAXIMUM RATINGS (Ta=25ºC unless specified otherwise)
DESCRIPTION
SYMBOL
BC307 BC308 BC309
VCEO
Collector Emitter Voltage
45
25
25
VCBO
50
30
30
Collector Base Voltage
VEBO
Emitter Base Voltage
5
5
5
IC
Collector Current Continuous
100
PD
Power Dissipation@ Ta=25ºC
350
Derate Above 25ºC
2.8
P
Power Dissipation@ Tc=25ºC
1
D
Derate Above 25ºC
8
Tj, Tstg
Operating And Storage Junction
-55 to +150
Temperature Range
THERMAL RESISTANCE
Junction to ambient
Junction to case
Continental Device India Limited
Rth(j-a)
Rth(j-c)
357
125
Data Sheet
UNITS
V
V
V
mA
mW
mW/°C
W
mW/°C
°C
°C/W
°C/W
Page 1 of 5
SILICON PLANAR EPITAXIAL TRANSISTORS
BC 307, A, B, C
BC 308, A, B, C
BC 309, A, B, C
TO-92
Plastic Package
ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise)
DESCRIPTION
SYMBOL TEST CONDITION MIN
BVCEO IC=2mA,IB=0
Collector Emitter Breakdown
Voltage
BC307
45
BC308, BC309
25
Emitter Base Breakdown Voltage
Collector Emitter Leakage Current
BC307
BVEBO
ICES
BC308, BC309
BC307
IE=100uA, IC=0
TYP
MAX
UNITS
V
V
5
V
VCES =50V, VBE =0
15
nA
VCES =30V, VBE =0
15
nA
VCES =50V, VBE =0,
4
µA
4
µA
o
TA =125 C
VCES =30V, VBE =0,
BC308, BC309
o
TA =125 C
DC Current Gain
A
B
C
BC307, BC308, BC309
A
B
C
A
B
C
Collector Emitter Saturation
Voltage
Base Emitter Saturation Voltage
Base Emitter On Voltage
Continental Device India Limited
hFE
IC=10uA,VCE=5V
IC=2mA,VCE=5V
90
150
270
120
120
200
420
170
290
500
0.55
120
180
300
0.10
0.25
0.7
1.0
0.62
IC=2mA,VCE=5V*
VCE(sat) IC=10mA,IB=0.5mA
IC=100mA,IB=5mA
VBE(sat) IC=10mA,IB=0.5mA
IC=100mA,IB=5mA
VBE(on) IC=2mA,VCE=5V
Data Sheet
800
220
460
800
0.3
0.7
V
V
V
V
V
Page 2 of 5
SILICON PLANAR EPITAXIAL TRANSISTORS
BC 307, A, B, C
BC 308, A, B, C
BC 309, A, B, C
TO-92
Plastic Package
ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise)
DESCRIPTION
SYMBOL TEST CONDITION MIN
DYNAMIC CHARACTERISTICS
fT
Transition Frequency
BC307
BC308
BC309
Collector Base Capacitance
BC 309
BC307, BC308
BC309
MAX
UNITS
IC=10mA, VCE=5V
f=50MHz
Ccbo
VCB=10V, IE=0
NF
f=1MHz
IC=0.2mA, VCE=5V
Noise Figure
TYP
Rg=2KΩ f=30Hz to
15KHz
f =1KHz, B=200Hz
280
320
360
MHz
MHz
MHz
6
pF
2
4
dB
2
2
10
4
dB
dB
RS=2KΩ f=30Hz
to 15KHz
*Pulse Condition: Width < 300µs, Duty Cycle < 2%.
Continental Device India Limited
Data Sheet
Page 3 of 5
BC 307, A, B, C
BC 308, A, B, C
BC 309, A, B, C
TO-92
Plastic Package
TO-92 Plastic Package
Dimension With 'L'
Uncontrolled
B
TO-92 Transistors on Tape and Ammo Pack
Ammo Pack Style
A
MECHANICAL DATA
h
P
T
h
(p)
A1
LABEL
A
L
H1
D
FEE
Carrier
Strip
FLAT SIDE
8.2"
W2
H0
L
Wo
W1
W
1
13"
t1
K
2
F1
t
F
D
3
D
A A
C
3 2 1
H
F
F
PIN CONFIGURATION
1. EMITTER
2. BASE
3. COLLECTOR
1.7
Do
7"
Po
3
2
1
DIM
MIN.
MAX.
A
B
4.32
4.45
5.33
5.20
C
D
3.18
0.41
4.19
0.55
E
F
0.35
0.50
5 DEG
G
H
1.14
1.14
1.40
1.53
K
L
12.70
1.982
—
2.082
All diminsions in mm.
Flat Side of Transistor and
Adhesive Tape Visible
2000 pcs./Ammo Pack
All dimensions in mm unless specified otherwise
ITEM
SEC AA
G
F2
P2
E
Solderability Ensured
Beyond 'L'
Adhesive Tape on Top Side
SYMBOL
BODY WIDTH
BODY HEIGHT
BODY THICKNESS
PITCH OF COMPONENT
FEED HOLE PITCH
A1
A
T
P
Po
FEED HOLE CENTRE TO
COMPONENT CENTRE
P2
DISTANCE BETWEEN OUTER
LEADS
COMPONENT ALIGNMENT
TAPE WIDTH
HOLD-DOWN TAPE WIDTH
HOLE POSITION
F
h
W
Wo
W1
HOLD-DOWN TAPE POSITION
LEAD WIRE CLINCH HEIGHT
COMPONENT HEIGHT
LENGTH OF SNIPPED LEADS
FEED HOLE DIAMETER
TOTAL TAPE THICKNESS
LEAD - TO - LEAD DISTANCEF1,
W2
Ho
H1
L
Do
t
F2
CLINCH HEIGHT
PULL - OUT FORCE
H2
(P)
SPECIFICATION
REMARKS
MIN. NOM. MAX. TOL .
4.0
4.8
5.2
4.8
4.2
3.9
12.7
±1
12.7
±0.3 CUMULATIVE PITCH
ERROR 1.0 mm/20
PITCH
6.35
±0.4 TO BE MEASURED AT
BOTTOM OF CLINCH
+0.6
5.08
-0.2
1
0
AT TOP OF BODY
18
±0.5
6
±0.2
9
+0.7
-0.5
0.5
±0.2
16
±0.5
23.25
11.0
4
±0.2
1.2
t1 0.3 - 0.6
2.54
+0.4
-0.1
3
6N
NOTES
1. MAXIMUM ALIGNMENT DEVIATION BETWEEN LEADS NOT TO BE GREATER THAN 0.2 mm.
2. MAXIMUM NON-CUMULATIVE VARIATION BETWEEN TAPE FEED HOLES SHALL NOT EXCEED 1 mm IN 20
PITCHES.
3. HOLDDOWN TAPE NOT TO EXCEED BEYOND THE EDGE(S) OF CARRIER TAPE AND THERE SHALL BE NO
EXPOSURE OF ADHESIVE.
4. NO MORE THAN 3 CONSECUTIVE MISSING COMPONENTS ARE PERMITTED.
5. A TAPE TRAILER, HAVING AT LEAST THREE FEED HOLES ARE REQUIRED AFTER THE LAST COMPONENT.
6. SPLICES SHALL NOT INTERFERE WITH THE SPROCKET FEED HOLES.
Packing Detail
PACKAGE
TO-92 Bulk
TO-92 T&A
STANDARD PACK
Details
Net Weight/Qty
1K/polybag
200 gm/1K pcs
2K/ammo box
645 gm/2K pcs
Continental Device India Limited
INNER CARTON BOX
Size
Qty
3" x 7.5" x 7.5"
5K
12.5" x 8" x 1.8"
2K
Data Sheet
OUTER CARTON BOX
Size
Qty
Gr Wt
17" x 15" x 13.5"
80K
23 kgs
17" x 15" x 13.5"
32K
12.5 kgs
Page 4 of 5
Notes
BC 307, A, B, C
BC 308, A, B, C
BC 309, A, B, C
TO-92
Plastic Package
Disclaimer
The product information and the selection guides facilitate selection of the CDIL's Discrete Semiconductor Device(s) best suited
for application in your product(s) as per your requirement. It is recommended that you completely review our Data Sheet(s) so as
to confirm that the Device(s) meet functionality parameters for your application. The information furnished in the Data Sheet and
on the CDIL Web Site/CD is believed to be accurate and reliable. CDIL however, does not assume responsibility for inaccuracies
or incomplete information. Furthermore, CDIL does not assume liability whatsoever, arising out of the application or use of any
CDIL product; neither does it convey any license under its patent rights nor rights of others. These products are not designed for
use in life saving/support appliances or systems. CDIL customers selling these products (either as individual Discrete
Semiconductor Devices or incorporated in their end products), in any life saving/support appliances or systems or applications do
so at their own risk and CDIL will not be responsible for any damages resulting from such sale(s).
CDIL strives for continuous improvement and reserves the right to change the specifications of its products without prior notice.
CDIL is a registered Trademark of
Continental Device India Limited
C-120 Naraina Industrial Area, New Delhi 110 028, India.
Telephone + 91-11-579 6150 Fax + 91-11-579 9569, 579 5290
e-mail [email protected]
www.cdil.com
BC307_9_A_B_C Rev160701
Continental Device India Limited
Data Sheet
Page 5 of 5
Similar pages