TC7MH240,244FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7MH240FK,TC7MH244FK Octal Bus Buffer TC7MH240FK Inverted, 3-State Outputs TC7MH244FK Non-Inverted, 3-State Outputs The TC7MH240FK and TC7MH244FK are advanced high speed CMOS octal bus buffers fabricated with silicon gate C2MOS technology. They achieve the high speed operation similar to equivalent bipolar schottky TTL while maintaining the CMOS low power dissipation. The TC7MH240FK is an inverting 3-state buffer having two active-low output enables. The TC7MH244FK is a non-inverting 3-state buffer, and has two active-low output enables. Weight: 0.03 g (typ.) These devices are designed to be used with 3-state memory address drivers, etc. An input protection circuit ensures that 0 to 5.5 V can be applied to the input pins without regard to the supply voltage. This device can be used to interface 5 V to 3 V systems and two supply systems such as battery back up. This circuit prevents device destruction due to mismatched supply and input voltages. Features • High speed: tpd = 3.9 ns (typ.) (VCC = 5 V) • Low power dissipation: ICC = 4 μA (max) (Ta = 25°C) • High noise immunity: VNIH = VNIL = 28% VCC (min) • Power down protection is provided on all inputs. • Balanced propagation delays: tpLH ≈ tpHL • Wide operating voltage range: VCC (opr) = 2~5.5 V • Low noise: VOLP = 0.8 (max) • Pin and function compatible with 74ALS240/244 1 2007-10-19 TC7MH240,244FK Pin Assignment (top view) TC7MH240FK TC7MH244FK 1G 1 20 VCC 1G 1 20 VCC 1A1 2 19 2G 1A1 2 19 2G 2Y 4 3 18 1Y1 2Y4 3 18 1Y1 1A2 4 17 2A4 1A2 4 17 2A4 2Y3 5 16 1Y 2 2Y3 5 16 1Y2 1A3 6 15 2A3 1A3 6 15 2A3 2Y2 7 14 1Y 3 2Y2 7 14 1Y3 1A4 8 13 2A2 1A4 8 13 2A2 2 Y1 9 12 1Y 4 2Y1 9 12 1Y4 GND 10 11 2A1 GND 10 11 2A1 IEC Logic Symbol (1) 1G 1A3 1A4 2A1 2A2 2A3 2A4 EN 1G (2) (4) (6) 1A1 1A2 2G TC7MH240FK (18) (16) (14) (12) (8) (19) 1Y1 1Y 2 1A1 1A2 1Y 3 1Y 4 1A3 1A4 2G EN (11) (13) (15) (17) (9) (7) (5) (3) 2A1 2A2 2A3 2A4 2 Y1 2Y2 2Y3 2Y 4 (1) TC7MH244FK EN (2) (4) (6) (18) (16) (14) (12) (8) (19) (11) (13) (15) (17) 1Y1 1Y2 1Y3 1Y4 EN (9) (7) (5) (3) 2Y1 2Y2 2Y3 2Y4 Truth Table Inputs Outputs G An Yn Yn L L L H L H H L H X Z Z X : Don’t care Z : High impedance Yn : TC7MH244FK Y n : TC7MH240FK 2 2007-10-19 TC7MH240,244FK Absolute Maximum Ratings (Note) Characteristics Symbol Rating Unit Supply voltage range VCC −0.5~7.0 V DC input voltage VIN −0.5~7.0 V VOUT −0.5~VCC + 0.5 V Input diode current IIK −20 mA Output diode current IOK ±20 mA DC output current IOUT ±25 mA DC VCC/ground current ICC ±75 mA Power dissipation PD 180 mW Storage temperature Tstg −65~150 °C DC output voltage Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Operating Ranges (Note) Characteristics Symbol Rating Unit Supply voltage VCC 2.0~5.5 V Input voltage VIN 0~5.5 V VOUT 0~VCC V Operating temperature Topr −40~85 °C Input rise and fall time dt/dv Output voltage 0~100 (VCC = 3.3 ± 0.3 V) 0~20 (VCC = 5 ± 0.5 V) ns/V Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. 3 2007-10-19 TC7MH240,244FK Electrical Characteristics DC Characteristics Characteristics High level Symbol Test Condition VIH ⎯ Ta = 25°C Min Typ. Max Min Max 2.0 1.50 ⎯ ⎯ 1.50 ⎯ 3.0~5.5 VCC × 0.7 ⎯ ⎯ VCC × 0.7 ⎯ 2.0 ⎯ ⎯ 0.50 ⎯ 0.50 3.0~5.5 ⎯ ⎯ VCC × 0.3 ⎯ VCC × 0.3 2.0 1.9 2.0 ⎯ 1.9 ⎯ 3.0 2.9 3.0 ⎯ 2.9 ⎯ 4.5 4.4 4.5 ⎯ 4.4 ⎯ IOH = −4 mA 3.0 2.58 ⎯ ⎯ 2.48 ⎯ IOH = −8 mA 4.5 3.94 ⎯ ⎯ 3.80 ⎯ 2.0 ⎯ 0 0.1 ⎯ 0.1 3.0 ⎯ 0 0.1 ⎯ 0.1 4.5 ⎯ 0 0.1 ⎯ 0.1 IOL = 4 mA 3.0 ⎯ ⎯ 0.36 ⎯ 0.44 IOL = 8 mA 4.5 ⎯ ⎯ 0.36 ⎯ 0.44 5.5 ー ー ±0.25 ー ±2.50 μA ⎯ VIL IOH = −50 μA High level VOH VIN = VIH or VIL Output voltage IOL = 50 μA Low level VOL Unit VCC (V) Input voltage Low level Ta = −40~85°C VIN = VIH or VIL VIN = VIH or VIL V V 3-state output off-state current IOZ Input leakage current IIN VIN = 5.5 V or GND 0~5.5 ⎯ ⎯ ±0.1 ⎯ ±1.0 μA Quiescent supply current ICC VIN = VCC or GND 5.5 ⎯ ⎯ 4.0 ⎯ 40.0 μA VOUT = VCC or GND 4 2007-10-19 TC7MH240,244FK AC Characteristics (Input: tr = tf = 3 ns) Characteristics Propagation delay time (TC7MH240FK) Propagation delay time (TC7MH244FK) Symbol Ta = 25°C Test Condition VCC (V) CL (pF) Min Typ. Max Min Max 15 ⎯ 5.3 7.5 1.0 9.0 50 ⎯ 7.8 11.0 1.0 12.5 15 ⎯ 3.6 5.5 1.0 6.5 50 ⎯ 5.1 7.5 1.0 8.5 15 ⎯ 5.8 8.4 1.0 10.0 50 ⎯ 8.3 11.9 1.0 13.5 15 ⎯ 3.9 5.5 1.0 6.5 50 ⎯ 5.4 7.5 1.0 8.5 15 ⎯ 6.6 10.6 1.0 12.5 50 ⎯ 9.1 14.1 1.0 16.0 15 ⎯ 4.7 7.3 1.0 8.5 50 ⎯ 6.2 9.3 1.0 10.5 3.3 ± 0.3 50 ⎯ 10.3 14.0 1.0 16.0 5.0 ± 0.5 50 ⎯ 6.7 9.2 1.0 10.5 3.3 ± 0.3 50 ⎯ ⎯ 1.5 ⎯ 1.5 5.0 ± 0.5 50 ⎯ ⎯ 1.0 ⎯ 1.0 3.3 ± 0.3 tpLH tpHL ⎯ 5.0 ± 0.5 3.3 ± 0.3 tpLH tpHL ⎯ 5.0 ± 0.5 3.3 ± 0.3 3-state output enable time tpZL tpZH RL = 1 kΩ 5.0 ± 0.5 3-state output disable time tpLZ tpHZ Output to output skew tosLH tosHL Input capacitance Output capacitance Power dissipation capacitance (Note 2) RL = 1 kΩ (Note 1) Ta = −40~85°C Unit ns ns ns ns ns CIN ⎯ ⎯ 4 10 ⎯ 10 pF COUT ⎯ ⎯ 6 ⎯ ⎯ ⎯ pF TC7MH240FK ⎯ 17 ⎯ ⎯ ⎯ TC7MH244FK ⎯ 19 ⎯ ⎯ ⎯ CPD pF Note 1: Parameter guaranteed by design. tosLH = |tpLHm − tpLHn|, tosHL = |tpHLm − tpHLn| Note 2: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC/8 (per bit) 5 2007-10-19 TC7MH240,244FK Noise Characteristics (Input: tr = tf = 3 ns) Characteristics Symbol Test Condition Ta = 25°C VCC (V) Typ. Limit Unit Quiet output maximum dynamic VOL VOLP CL = 50 pF 5.0 0.5 0.8 V Quiet output minimum dynamic VOL VOLV CL = 50 pF 5.0 −0.5 −0.8 V Minimum high level dynamic input voltage VIH VIHD CL = 50 pF 5.0 ⎯ 3.5 V Maximum low level dynamic input voltage VIL VILD CL = 50 pF 5.0 ⎯ 1.5 V Input Equivalent Circuit Input 6 2007-10-19 TC7MH240,244FK Package Dimensions Weight: 0.03 g (typ.) 7 2007-10-19 TC7MH240,244FK RESTRICTIONS ON PRODUCT USE 20070701-EN GENERAL • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 8 2007-10-19