APW7065 Synchronous Buck PWM Controller Features General Description • • The APW7065 uses fixed 300KHz switching frequency, voltage mode, synchronous PWM controller which drives dual N-channel MOSFETs. The device integrates the control, monitoring and protection functions into a single package, provides one controlled power output with under-voltage and over-current protections. Single 12V Power Supply Required Fast Transient Response - 0~90% Duty Ratio • • 0.8V Reference with 1% Accuracy Shutdown Function by Controlling COMP Pin Voltage • • • • The APW7065 provides excellent regulation for output load variation. The internal 0.8V temperaturecompensated reference voltage is designed to meet the requirement of low output voltage applications. An built-in digital soft-start with fixed soft-start interval prevents the output voltage from overshoot as well as limiting the input current. Internal Soft-Start (3.4ms) Function Voltage Mode PWM Control Design Under-Voltage Protection Over-Current Protection - Sense Low Side MOSFET’s RDS(ON) • • • 300KHz Fixed Switching Frequency The APW7065 with excellent protection functions: POR, OCP and UVP. The Power-On Reset (POR) circuit can monitor VCC supply voltage exceeds its threshold voltage while the controller is running, and a built-in digital soft-start provides output with controlled voltage rise. The Over-Current Protection (OCP) monitors the output current by using the voltage drop across the lower MOSFET’s RDS(ON), comparing with internal VOCP (0.27V), when the output current reaches the trip point, the controller will run the soft-start function until the fault events are removed. The UnderVoltage Protection (UVP) monitors the voltage of FB pin for short-circuit protection, when the VFB is less than 50% of VREF (0.4V), the controller will shutdown the IC directly. SOP-8 Package Lead Free Available (RoHS Compliant) Applications • • Graphics Card Mother Board Pinouts BOOT 1 8 PHASE UGATE 2 7 COMP GND 3 6 FB LGATE 4 5 VCC SOP-8 ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 1 www.anpec.com.tw APW7065 Ordering and Marking Information Package Code K : SOP-8 Operating Ambient Temp. Range E : -20 to 70 °C Handling Code TU : Tube TR : Tape & Reel Lead Free Code L : Lead Free Device Blank : Original Device APW 7065 Lead Free Code Handling Code Temp. Range Package Code APW7065 K : APW7065 XXXXX XXXXX - Date Code Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS and compatible with both SnPb and lead-free soldering operations. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J STD-020C for MSL classification at lead-free peak reflow temperature. Block Diagram VCC GND BOOT Power-On Reset UGATE Sense Low Side Digital Soft Start O.C.P Comparator PHASE 0.27V 50%VREF :2 U.V.P Comparator Error Amp PWM Comparator Gate Control LGATE VREF Oscillator Sawtooth Wave FOSC 300KHz FB Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 COMP 2 www.anpec.com.tw APW7065 Application Circuit 1N4148 12V V IN (12V) 1uH 2.2R 1uF 1uF 5 VCC BOOT 1 UGATE 2 0.1uF PHASE Q3 2N7002 7 LGATE 33nF 6 V OUT (1.2V) 1uH 4 470uF Q1 APM2509 8 COMP ON/OFF 470uFx2 Q2 APM2506 470uFx2 FB GND 8.2nF 3 2.7K 1K 2K 18R 68nF Absolute Maximum Ratings Symbol VCC BOOT UGATE LGATE PHASE COMP, FB TJ TSTG Parameter VCC to GND BOOT to PHASE UGATE to PHASE LGATE to GND PHASE to GND <400nS pulse width >400nS pulse width <400nS pulse width >400nS pulse width <400nS pulse width >400nS pulse width COMP, FB to GND Junction Temperature Range Storage Temperature Rating Unit -0.3 ~ 16 V -0.3 ~ 16 V -5 ~ BOOT+5 -0.3 ~ BOOT+0.3 -5 ~ VCC+5 -0.3 ~ VCC+0.3 -5 ~ 21 -0.3 ~ 16 -0.3 ~ 7 V V V V -20 ~ 150 o -65 ~ 150 o o TSDR Maximum Soldering Temperature, 10 Seconds 300 VESD Minimum ESD Rating (Human Body Mode) (Note 2) ±2 C C C kV Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note 2: The device is ESD sensitive. Handling precautions are recommended. Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 3 www.anpec.com.tw APW7065 Recommended Operating Conditions Symbol Parameter VCC VCC Supply Voltage VOUT Converter Output Voltage VIN Converter Input Voltage IOUT Converter Output Current TA TJ Range Unit 10.8 ~ 13.2 V 0.8 ~ 5 V 2.9 ~ 13.2 V 0 ~ 20 -20 ~ 70 -20 ~ 125 o Ambient Temperature Range Junction Temperature Range A o C C Electrical Characteristics Unless otherswise specified, these specifications apply over VCC=12V, and TA =-20~70oC. Typlcal values are at TA=25oC. Symbol Parameter Test Conditions APW7065 Min Typ Max Unit SUPPLY CURRENT IVCC VCC Nominal Supply Current UGATE and LGATE Open 5 10 mA VCC Shutdown Supply Current UGATE, LGATE = GND 1 2 mA 9.5 8 1.2 10 8.5 V V V POWER-ON RESET Rising VCC Threshold Falling VCC Threshold COMP Shutdown Threshold 9 7.5 COMP Shutdown Hysteresis 0.1 V OSCILLATOR FOSC ∆VOSC Free Running Frequency 255 Ramp Amplitude 300 345 kHz 1.6 VP-P 0.8 V REFERENCE VOLTAGE VREF Reference Voltage Measured at FB Pin Accuracy TA =-20~70°C -1.0 +1.0 % ERROR AMPLIFIER Gain Open Loop Gain RL=10k, CL=10pF(Note3) 88 dB RL=10k, CL=10pF(Note3) 15 MHz Slew Rate R =10k, C =10pF(Note3) 6 V/us FB Input Current VFB = 0.8V(Note3) GBWP Open Loop Bandwidth SR L L 0.1 1 uA VCOMP COMP High Voltage 5.5 V VCOMP COMP Low Voltage 0 V Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 4 www.anpec.com.tw APW7065 Electrical Characteristics (Cont.) Unless otherswise specified, these specifications apply over VCC=12V and TA =-20~70oC. Typlcal values are at TA=25oC. Symbol Parameter Test Conditions APW7065 Min Typ Max Unit ERROR AMPLIFIER (Cont.) ICOMP COMP Source Current VCOMP=2V 5 mA ICOMP COMP Sink Current VCOMP=2V 5 mA BOOT = 12V, VUGATE -VPHASE = 2V BOOT = 12V, VUGATE -VPHASE = 2V 2.6 1.05 A A GATE DRIVERS IUGATE Upper Gate Source Current IUGATE Upper Gate Sink Current ILGATE Lower Gate Source Current VCC = 12V, VLGATE = 2V 4.9 A ILGATE Lower Gate Sink Current VCC = 12V, VLGATE = 2V 1.4 A RUGATE Upper Gate Source Impedance BOOT = 12V, IUGATE = 0.1A 2 3 Ω RUGATE Upper Gate Sink Impedance BOOT = 12V, IUGATE = 0.1A 1.6 2.4 Ω RLGATE Lower Gate Source Impedance VCC = 12V, ILGATE = 0.1A 1.3 1.95 Ω RLGATE Lower Gate Sink Impedance VCC = 12V, ILGATE = 0.1A 1.25 1.88 Ω TD Dead Time 20 nS PROTECTIONS VOCP Over-Current Reference Voltage TA =-20~70°C VUVP Under-Voltage Threshold Trip Point Percent of VREF 0.23 0.27 0.31 V 45 50 55 % 2 3.4 5 ms SOFT-START TSS Soft-Start Interval Note 3: Guaranteed by design. Functional Pin Description BOOT (Pin 1) GND (Pin 3) A bootstrap circuit with a diode connected to VCC is used to create a voltage suitable to drive a logic-level N-channel MOSFET. The GND terminal provides return path for the IC’s bias current and the low-side MOSFET driver’s pull-low current. Connect the pin to the system ground via very low impedance layout on PCBs. UGATE (Pin 2) LGATE (Pin 4) Connect this pin to the high-side N-channel MOSFET’s gate. This pin provides gate drive for the high-side MOSFET. Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 Connect this pin to the low-side N-channel MOSFET’s gate. This pin provides gate drive for the low-side MOSFET. 5 www.anpec.com.tw APW7065 Functional Pin Description (Cont.) VCC (Pin 5) FB pin is also monitored for under voltage events. Connect this pin to a 12V supply voltage. This pin provides bias supply for the control circuitry and the low-side MOSFET driver. The voltage at this pin is monitored for the Power-On Reset (POR) purpose. It is recommended that a decoupling capacitor (1 to 10uF) be connected to GND for noise decoupling. COMP (Pin 7) This pin is the output of PWM error amplifier. It is used to set the compensation components. In addition, if the pin is pulled below 1.2V, it will disable the device. PHASE (Pin 8) FB (Pin 6) This pin is the return path for the upper gate driver. Connect this pin to the upper MOSFET source. This pin is also used to monitor the voltage drop across the MOSFET for over-current protection. This pin is the inverting input of the internal error amplifier. Connect this pin to the output (VOUT) of the converter via an external resistor divider for closedloop operation. The output voltage set by the resistor divider is determined using the following formula : R1 VOUT = 0.8 × 1 + R2 where R1 is the resistor connected from VOUT to FB , and R2 is the resistor connected from FB to GND. The Typical Characteristics Power On Power Off VCC=12V, Vin=12V Vo=1.2V, L=1uH CH1 VCC=12V, Vin=12V Vo=1.2V, L=1uH CH1 CH2 CH2 CH3 CH3 CH4 CH4 CH1: VCC (5V/div) CH2: VFB (1V/div) CH3: Vo (1V/div) CH4: Ug (20/Vdiv) Time: 10ms/div Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 CH1: VCC (5V/div) CH2: VFB (1V/div) CH3: Vo (1V/div) CH4: Ug (20/Vdiv) Time: 10ms/div 6 www.anpec.com.tw APW7065 Typical Characteristics (Cont.) Shutdown EN VCC=12V, Vin=12V Vo=1.2V, L=1uH VCC=12V, Vin=12V Vo=1.2V, L=1uH CH1 CH1 CH2 CH2 CH3 CH3 CH4 CH4 CH1: VCOMP (2V/div) CH2: Vo (1V/div) CH3: Ug (20V/div) CH4: Lg (10Vdiv) Time: 5ms/div CH1: VCOMP (2V/div) CH2: Vo (1V/div) CH3: Ug (20V/div) CH4: Lg (10Vdiv) Time: 20us/div UGATE Rising UGATE Falling VCC=12V, Vin=12V Vo=1.2V, L=1uH Iout=5A VCC=12V, Vin=12V Vo=1.2V, L=1uH Iout=5A CH1 CH1 CH2 CH2 CH3 CH3 CH1: IL (10A/div) CH2: Vo (1V/div) CH3: Ug (20V/div) CH4: Lg(10V/div) Time: 100us/div CH1: Ug (20V/div) CH2: Lg (5V/div) CH3: Phase (10V/div) Time: 50ns/div Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 7 www.anpec.com.tw APW7065 Typical Characteristics (Cont.) Load Transient Response Under Voltage Protection VCC=12V, Vin=12V Vo=1.2V, L=1uH VCC=12V, Vin=12V Vo=1.2V, L=4.7uH CH1 CH1 0 CH2 10A CH3 0A CH2 CH4 CH1: Vo (500mV/div,AC) CH2:Io (5A/div) Time: 1ms/div 1 2 1 CH1: IL (10A/div) CH2: Vo (1V/div) CH3: Ug (20V/div) CH4: Lg (10V/div) Time: 100us/div 2 Over Current Protection Short Test VCC=12V, Vin=12V,Vo=1.2V, L=1uH, L_side: APM2023, Rds(on)=17mΩ VCC=12V, Vin=12V Vo=1.2V, L=1uH CH1 CH1 CH2 CH2 CH3 CH3 CH4 CH4 CH1: IL (10A/div) CH2: Vo (2V/div) CH3: Ug (20V/div) CH4: Lg (10V/div) Time: 2ms/div Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 CH1: IL (10A/div) CH2: Vo (2V/div) CH3: Ug (20V/div) CH4: Lg (10V/div) Time: 5ms/div 8 www.anpec.com.tw APW7065 Typical Characteristics (Cont.) Switching Frequency vs. Junction Temperature Reference Voltage vs. Junction Temperature 0.804 VCC=12V 305 VCC=12V 0.802 Reference Voltage(V) Switching Frequency(KHz) 310 300 295 290 285 280 0.8 0.798 0.796 0.794 275 -40 -20 0 20 40 60 0.792 80 100 120 -40 -20 Junction Temperature (°C ) 20 40 60 80 100 120 Junction Temperature (°C ) UGATE Source Current vs. UGATE Voltage UGATE Sink Current vs. UGATE Voltage 3.5 3 VBOOT=12V PHASE=2V UGATE Sink Current (A) 3 UGATE Source Current (A) 0 2.5 2 1.5 1 0.5 VBOOT=12V PHASE=2V 2.5 2 1.5 1 0.5 0 0 0 2 4 6 8 10 0 12 UGATE Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 2 4 6 8 10 12 UGATE Voltage (V) 9 www.anpec.com.tw APW7065 Typical Characteristics (Cont.) LGATE Sink Current vs. LGATE Voltage LGATE Source Current vs. LGATE Voltage 3.5 VCC=12V 5 LGATE Sink Current (A) LGATE Source Current (A) 6 4 3 2 1 3 VCC=12V 2.5 2 1.5 1 0.5 0 0 0 2 4 6 8 10 0 12 LGATE Voltage (V) 2 4 6 8 10 12 LGATE Voltage (V) Functional Description Power On Reset (POR) seconds and then begin soft start. During soft-start, an internal ramp connected to the one of the positive inputs of the Gm amplifier rises up from 0V to 2V to replace the reference voltage (0.8V) until the ramp voltage reaches the reference voltage. The soft-start interval is decided by the oscillator frequency (300kHz). The formulation is given by: The Power-On Reset (POR) function of APW7065 continually monitors the input supply voltage (VCC) and the COMP pin. The supply voltage (VCC) must exceed its rising POR threshold voltage. The POR function initiates soft-start operation after VCC and COMP voltages exceed their POR thresholds. For operation with a single +12V power source, VIN and VCC are equivalent and the +12V power source must exceed the rising VCC threshold. The POR function inhibits operation at disabled status (VCOMP is less Tdelay = t 2 − t 1 = 2048/FOSC = 6.8ms than 1.2V). With both input supplies above their POR thresholds, the device initiates a soft-start interval. Tsoft−start = t 3 − t 2 = 1024/FOSC = 3.4ms Soft-Start Figure 2. shows more detail of the FB voltage ramp. The FB voltage soft-start ramp is formed with many small steps of voltage. The voltage of one step is about 12.5mV in FB, and the period of one step is about 16/ FOSC. This method provides a controlled voltage rise The APW7065 has a built-in digital soft-start to control the output voltage rise and limit the current surge during the start-up. In Figure 1, when VCC exceeds rising POR threshold voltage, it will delay 2048/Fosc Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 10 www.anpec.com.tw APW7065 Functional Description (Cont.) Soft-Start (Cont.) - The MOSFET’s RDS(ON) is varied by temperature and gate to source voltage, the user should determine the maximum RDS(ON) in manufacturer’s datasheet. - The minimum Vocset should be used in the above equation. and prevents the large peak current to charge output capacitor. Voltage(V) - Note that the ILIMIT is the current flow through the lower MOSFET; ILIMIT must be greater than maximum output current add the half of inductor ripple current. VCC V OUT Shutdown and Enable t1 Pulling the COMP voltage to GND by an open drain transistor, shown in typical application circuit, shutdown the APW7065 PWM controller. In shutdown mode, the UGATE and LGATE turn off and pull to PHASE and GND respectively. Time t2 t3 Figure 1. Voltage(V) FB Under Voltage Protection 12.5mV The FB pin is monitored during converter operation by the internal Under Voltage (UV) comparator. If the FB voltage drops below 50% of the reference voltage (50% of 0.8V = 0.4V), a fault signal is internally generated, and the device turns off both high-side and low-side MOSFET and the converter’s output is latched to be floating. 16/Fosc Time Figure 2. Over-Current Protection The over-current protection monitors the output current by using the voltage drop across the lower MOSFET’s RDS(ON) and this voltage drop will be compared with the internal 0.27V reference voltage. If the voltage drop across the lower MOSFET’s RDS(ON) is larger than 0.27V, an over-current condition is detected. The threshold of the over current limit is given by: ILimit = Application Information Output Voltage Selection The output voltage can be programmed with a resistive divider. Use 1% or better resistors for the resistive divider is recommended. The FB pin is the inverter input of the error amplifier, and the reference voltage is 0.8V. The output voltage is determined by: 0.27 R DS( ON) R V OUT = 0.8 × 1 + OUT R GND For the over-current is never occurred in the normal operating load range; the variation of all parameters in the above equation should be determined. Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 Where ROUT is the resistor connected from V OUT to FB and RGND is the resistor connected from FB to GND. 11 www.anpec.com.tw APW7065 Application Information (Cont.) Output Inductor Selection capacitors are used, make sure they are surge tested by the manufactures. If in doubt, consult the capacitors manufacturer. The inductor value determines the inductor ripple current and affects the load transient response. Higher inductor value reduces the inductor’s ripple current and induces lower output ripple voltage. The ripple current and ripple voltage can be approximated by: IRIPPLE = Input Capacitor Selection The input capacitor is chosen based on the voltage rating and the RMS current rating. For reliable operation, select the capacitor voltage rating to be at least 1.3 times higher than the maximum input voltage. The maximum RMS current rating requirement is approximately IOUT/2, where IOUT is the load current. During power up, the input capacitors have to handle large amount of surge current. If tantalum capacitors are used, make sure they are surge tested by the manufactures. If in doubt, consult the capacitors manufacturer. For high frequency decoupling, a ceramic capacitor 1uF can be connected between the drain of upper MOSFET and the source of lower MOSFET. VIN − VOUT V × OUT FS × L VIN ∆VOUT = IRIPPLE × ESR where FS is the switching frequency of the regulator. Although increase of the inductor value reduces the ripple current and voltage, a tradeoff will exist between the inductor’s ripple current and the regulator load transient response time. A smaller inductor will give the regulator a faster load transient response at the expense of higher ripple current. The maximum ripple current occurs at the maximum input voltage. A good starting point is to choose the ripple current to be approximately 30% of the maximum output current. Once the inductance value has been chosen, select an inductor that is capable of carrying the required peak current without going into saturation. In some types of inductors, especially core that is made of ferrite, the ripple current will increase abruptly when it saturates. This will result in a larger output ripple voltage. MOSFET Selection The selection of the N-channel power MOSFETs are determined by the RDS(ON), reverse transfer capacitance (CRSS) and maximum output current requirement. There are two components of loss in the MOSFETs: conduction loss and transition loss. For the upper and lower MOSFET, the losses are approximately given by the following: PUPPER = IOUT (1+ TC)(RDS(ON))D + (0.5)( IOUT)(VIN)( tSW)FS Output Capacitor Selection PLOWER = IOUT (1+ TC)(RDS(ON))(1-D) Higher capacitor value and lower ESR reduce the output ripple and the load transient drop. Therefore, selecting high performance low ESR capacitors is intended for switching regulator applications. In some applications, multiple capacitors have to be parallel to achieve the desired ESR value. A small decoupling capacitor in parallel for bypassing the noise is also recommended, and the voltage rating of the output capacitors also must be considered. If tantalum Where I OUT is the load current Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 TC is the temperature dependency of RDS(ON) FS is the switching frequency tSW is the switching interval D is the duty cycle Note that both MOSFETs have conduction loss while the upper MOSFET include an additional transition loss. The switching internal, tSW, is a function of the reverse transfer capacitance CRSS. The (1+TC) term is 12 www.anpec.com.tw APW7065 Application Information (Cont.) MOSFET Selection (Cont.) F LC to factor in the temperature dependency of the RDS(ON) and can be extracted from the “RDS(ON) vs Temperature” curve of the power MOSFET. GAIN (dB) -40dB/dec PWM Compensation The output LC filter of a step down converter introduces a double pole, which contributes with -40dB/decade gain slope and 180 degrees phase shift in the control loop. A compensation network among COMP, FB and VOUT should be added. The compensation network is shown in Fig. 6. The output LC filter consists of the output inductor and output capacitors. The transfer function of the LC filter is given by: GAIN LC = -20dB/dec Frequency(Hz) Figure 4. The LC Filter GAIN and Frequency The PWM modulator is shown in Figure 5. The input is the output of the error amplifier and the output is the PHASE node. The transfer function of the PWM modulator is given by: VIN GAIN PWM = ∆ VOSC 1 + s × ESR × C OUT s 2 × L × C OUT + s × ESR × C OUT + 1 V IN The poles and zero of this transfer functions are: 1 FLC = 2 × π × L × C OUT FESR = F ESR OSC ΔV OSC Driver PWM Comparator PHASE Output of Error Amplifier 1 2 × π × ESR × C OUT Driver The FLC is the double poles of the LC filter, and FESR is the zero introduced by the ESR of the output capacitor. PHASE L Figure 5. The PWM Modulator The compensation network is shown in Figure 6. It provides a close loop transfer function with the highest zero crossover frequency and sufficient phase margin. The transfer function of error amplifier is given by: OUTPUT 1 1 // R2 + sC1 sC2 = GAIN AMP 1 R1// R3 + sC3 1 1 s + × s + R2 × C2 ( R1 + R3 ) × C3 R1 + R3 = × C1 + C2 1 R1 × R3 × C1 s s + × s + R2 × C1 × C2 R3 × C3 COUT V = COMP V OUT ESR Figure 3. The Output LC Filter Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 13 www.anpec.com.tw APW7065 Application Information (Cont.) PWM Compensation (Cont.) Calculate the C2 by the equation: 1 C2 = 2 × π × R2 × FLC × 0.75 4.Set the pole at the ESR zero frequency FESR: FP1 = FESR The poles and zeros of the transfer function are: F Z1 = 1 2 × π × R2 × C2 F Z2 = 1 2 × π × (R1 + R3 ) × C3 FP1 = FP2 Calculate the C1 by the equation: C2 C1 = 2 × π × R2 × C2 × FESR − 1 1 C1 × C2 2 × π × R2 × C1 + C2 5.Set the second pole FP2 at the half of the switching frequency and also set the second zero F Z2 at the output LC filter double pole FLC. The compensation gain should not exceed the error amplifier open loop gain, check the compensation gain at FP2 with the capabilities of the error amplifier. 1 = 2 × π × R3 × C3 C1 R3 C3 R2 C2 V OUT R1 FB V COMP FP2 = 0.5 X FO V REF FZ2 = FLC Figure 6. Compensation Network Combine the two equations will get the following component calculations: R1 R3 = FS −1 2 × FLC 1 C3 = π × R3 × FS The closed loop gain of the converter can be written as: GAINLC X GAINPWM X GAINAMP Figure 7. shows the asymptotic plot of the closed loop converter gain, and the following guidelines will help to design the compensation network. Using the below guidelines should give a compensation similar to the curve plotted. A stable closed loop has a -20dB/ decade slope and a phase margin greater than 45 degree. F Z1 F Z2 GAIN (dB) 1.Choose a value for R1, usually between 1K and 5K. 2.Select the desired zero crossover frequency F O: (1/5 ~ 1/10) X F S >FO>FESR F P1 20log (R2/R1) F P2 20log (V IN /Δ V OSC ) Compensation Gain Use the following equation to calculate R2: F LC ∆ VOSC FO R2 = × × R1 VIN FLC F ESR 3.Place the first zero FZ1 before the output LC filter double pole frequency F LC. Frequency(Hz) Figure 7. Converter Gain and Frequency FZ1 = 0.75 X FLC Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 Converter Gain PWM & Filter Gain 14 www.anpec.com.tw APW7065 Application Information (Cont.) the resistor dividers, and boot capacitors should be close their pins. (For example, place the decoupling ceramic capacitor near the drain of the high-side MOSFET as close as possible. The bulk capacitors are also placed near the drain). Layout Considerations In any high switching frequency converter, a correct layout is important to ensure proper operation of the regulator. With power devices switching at 300KHz, the resulting current transient will cause voltage spike across the interconnecting impedance and parasitic circuit elements. As an example, consider the turn-off transition of the PWM MOSFET. Before turn-off, the MOSFET is carrying the full load current. During turn-off, current stops flowing in the MOSFET and is free-wheeling by the lower MOSFET and parasitic diode. Any parasitic inductance of the circuit generates a large voltage spike during the switching interval. In general, using short, wide printed circuit traces should minimize interconnecting impedances and the magnitude of voltage spike. And signal and power grounds are to be kept separate till combined using ground plane construction or single point grounding. Figure 8. illustrates the layout, with bold lines indicating high current paths; these traces must be short and wide. Components along the bold lines should be placed lose together. Below is a checklist for your layout: - The input capacitor should be near the drain of the upper MOSFET; the output capacitor should be near the loads. The input capacitor GND should be close to the output capacitor GND and the lower MOSFET GND. - The drain of the MOSFETs (VIN and PHASE nodes) should be a large plane for heat sinking. APW7065 VIN VCC BOOT L O A D UGATE PHASE LGATE VOUT Figure 8.Layout Guidelines - Keep the switching nodes (UGATE, LGATE and PHASE) away from sensitive small signal nodes since these nodes are fast moving signals. Therefore, keep traces to these nodes as short as possible. - The traces from the gate drivers to the MOSFETs (UG, LG) should be short and wide. - Place the source of the high-side MOSFET and the drain of the low-side MOSFET as close possible. Minimizing the impedance with wide layout plane between the two pads reduces the voltage bounce of the node. - Decoupling capacitor, compensation component, Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 15 www.anpec.com.tw APW7065 Package Information E e1 0.015X45 SOP-8 pin (Reference JEDEC Registration MS-012) H e2 D A1 A 1 L 0.004max. Dim Millimeters Inches Min. Max. Min. Max. A A1 1.35 0.10 1.75 0.25 0.053 0.004 0.069 0.010 D E 4.80 3.80 5.00 4.00 0.189 0.150 0.197 0.157 H L 5.80 0.40 6.20 1.27 0.228 0.016 0.244 0.050 e1 e2 0.33 0.51 0.013 0.020 φ1 0° 8° 0° 1.27BSC Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 0.50BSC 16 8° www.anpec.com.tw APW7065 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) tp TP Critical Zone T L to T P Temperature Ramp-up TL tL Tsmax Tsmin Ramp-down ts Preheat 25 t 25 °C to Peak Time Classificatin Reflow Profiles Profile Feature Average ramp-up rate (TL to TP) Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) Time maintained above: - Temperature (T L) - Time (tL) Peak/Classificatioon Temperature (Tp) Time within 5°C of actual Peak Temperature (tp) Ramp-down Rate Sn-Pb Eutectic Assembly Pb-Free Assembly 3°C/second max. 3°C/second max. 100°C 150°C 60-120 seconds 150°C 200°C 60-180 seconds 183°C 60-150 seconds 217°C 60-150 seconds See table 1 See table 2 10-30 seconds 20-40 seconds 6°C/second max. 6°C/second max. 6 minutes max. 8 minutes max. Time 25°C to Peak Temperature Notes: All temperatures refer to topside of the package .Measured on the body surface. Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 17 www.anpec.com.tw APW7065 Classification Reflow Profiles (Cont.) Table 1. SnPb Entectic Process – Package Peak Reflow Temperature s Package Thickness V o l u m e m m3 Volume mm 3 <350 ≥350 <2.5 mm 240 +0/-5°C 225 +0/-5°C ≥2.5 mm 225 +0/-5°C 225 +0/-5°C Table 2. Pb-free Process – Package Classification Reflow Temperatures Package Thickness Volume mm3 Volume mm3 Volume mm3 <350 350-2000 >2000 <1.6 mm 260 +0°C * 260 +0 °C * 260 +0°C * 1.6 mm – 2.5 mm 260 +0°C * 250 +0 °C * 245 +0°C * ≥2.5 mm 250 +0°C * 245 +0 °C * 245 +0°C * *Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated classification temperature (this means Peak reflow temperature +0 °C. For example 260°C+0°C) at the rated MSL level. Reliability Test Program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245°C, 5 SEC 1000 Hrs Bias @125°C 168 Hrs, 100%RH, 121°C -65°C~150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1 tr > 100mA Carrier Tape & Reel Dimensions t D P Po E P1 Bo F W Ko Ao Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 D1 18 www.anpec.com.tw APW7065 Carrier Tape & Reel Dimensions (Cont.) T2 J C A B T1 Reel Dimensions Application A 330 ± 1 SOP- 8 F 5.5± 1 B C 62 +1.5 12.75+ 0.15 D J T1 T2 W P E 2 ± 0.5 12.4 ± 0.2 2 ± 0.2 12± 0. 3 8± 0.1 1.75±0.1 Po P1 Ao Bo Ko t D1 1.55 +0.1 1.55+ 0.25 4.0 ± 0.1 2.0 ± 0.1 6.4 ± 0.1 5.2± 0. 1 2.1± 0.1 0.3±0.013 (mm) Cover Tape Dimensions Application SOP- 8 Carrier Width 12 Cover Tape Width 9.3 Devices Per Reel 2500 Customer Service Anpec Electronics Corp. Head Office : No.6, Dusing 1st Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. A.1 - Feb., 2006 19 www.anpec.com.tw