DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 Three Phase PWM Motor Driver Check for Samples: DRV8312, DRV8332 FEATURES 1 • • • • • • • • • • • High-Efficiency Power Stage (up to 97%) with Low RDS(on) MOSFETs (80 mΩ at TJ = 25°C) Operating Supply Voltage up to 50 V (70 V Absolute Maximum) DRV8312 (power pad down): up to 3.5 A Continuous Phase Current (6.5 A Peak) DRV8332 (power pad up): up to 8 A Continuous Phase Current ( 13 A Peak) Independent Control of Three Phases PWM Operating Frequency up to 500 kHz Integrated Self-Protection Circuits Including Undervoltage, Overtemperature, Overload, and Short Circuit Programmable Cycle-by-Cycle Current Limit Protection Independent Supply and Ground Pins for Each Half Bridge Intelligent Gate Drive and Cross Conduction Prevention No External Snubber or Schottky Diode is Required Because of the low RDS(on) of the power MOSFETs and intelligent gate drive design, the efficiency of these motor drivers can be up to 97%, which enables the use of smaller power supplies and heatsinks, and are good candidates for energy efficient applications. The DRV8312/32 require two power supplies, one at 12 V for GVDD and VDD, and another up to 50 V for PVDD. The DRV8312/32 can operate at up to 500kHz switching frequency while still maintain precise control and high efficiency. They also have an innovative protection system safeguarding the device against a wide range of fault conditions that could damage the system. These safeguards are shortcircuit protection, overcurrent protection, undervoltage protection, and two-stage thermal protection. The DRV8312/32 have a current-limiting circuit that prevents device shutdown during load transients such as motor start-up. A programmable overcurrent detector allows adjustable current limit and protection level to meet different motor requirements. The DRV8312/32 have unique independent supply and ground pins for each half bridge, which makes it possible to provide current measurement through external shunt resistor and support half bridge drivers with different power supply voltage requirements. Simplified Application Diagram APPLICATIONS PVDD • • • • • BLDC Motors Three Phase Permanent Magnet Synchronous Motors Inverters Half Bridge Drivers Robotic Control Systems GVDD GVDD_B OTW FAULT GVDD_A BST_A PVDD_A PWM_A OUT_A RESET_A GND_A PWM_B GND_B OC_ADJ OUT_B M Controller GND AGND DESCRIPTION The DRV8312/32 are high performance, integrated three phase motor drivers with an advanced protection system. BST_B VREG NC M3 NC M2 GND M1 PWM_C GVDD PVDD_B GND GND_C RESET_C OUT_C RESET_B PVDD_C VDD GVDD_C BST_C GVDD_C 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2010–2014, Texas Instruments Incorporated DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ABSOLUTE MAXIMUM RATINGS Over operating free-air temperature range unless otherwise noted (1) VALUE VDD to GND –0.3 V to 13.2 V GVDD_X to GND –0.3 V to 13.2 V PVDD_X to GND_X (2) –0.3 V to 70 V OUT_X to GND_X (2) –0.3 V to 70 V BST_X to GND_X (2) –0.3 V to 80 V Transient peak output current (per pin), pulse width limited by internal over-current protection circuit. 16 A Transient peak output current for latch shut down (per pin) 20 A VREG to AGND –0.3 V to 4.2 V GND_X to GND –0.3 V to 0.3 V GND to AGND –0.3 V to 0.3 V PWM_X, RESET_X to GND –0.3 V to 4.2 V OC_ADJ, M1, M2, M3 to AGND –0.3 V to 4.2 V FAULT, OTW to GND –0.3 V to 7 V Maximum continuous sink current (FAULT, OTW) 9 mA Maximum operating junction temperature range, TJ -40°C to 150°C Storage temperature, TSTG –55°C to 150°C (1) (2) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. These voltages represent the dc voltage + peak ac waveform measured at the terminal of the device in all conditions. THERMAL INFORMATION THERMAL METRIC (1) DRV8312 DRV8332 DDW PACKAGE DKD PACKAGE 44 PINS 36 PINS 13.3 (with heat sink) θJA Junction-to-ambient thermal resistance (2) 24.5 θJCtop Junction-to-case (top) thermal resistance (3) 7.8 0.4 θJB Junction-to-board thermal resistance (4) 5.5 13.3 ψJT Junction-to-top characterization parameter (5) 0.1 0.4 ψJB Junction-to-board characterization parameter (6) 5.4 13.3 θJCbot Junction-to-case (bottom) thermal resistance (7) 0.2 N/A (1) (2) (3) (4) (5) (6) (7) 2 UNITS °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as specified in JESD51-7, in an environment described in JESD51-2a. The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88. The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB temperature, as described in JESD51-8. The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted from the simulation data for obtaining θJA , using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88. Spacer Submit Documentation Feedback Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 RECOMMENDED OPERATING CONDITIONS MIN NOM MAX UNIT 0 50 52.5 V Supply for logic regulators and gate-drive circuitry 10.8 12 13.2 V VDD Digital regulator supply voltage 10.8 12 13.2 V IO_PULSE Pulsed peak current per output pin (could be limited by thermal) 15 A IO Continuous current per output pin (DRV8332) FSW PWM switching frequency ROCP_CBC OC programming resistor range in cycle-by-cycle current limit modes ROCP_OCL OC programming resistor range in OC latching shutdown modes CBST Bootstrap capacitor range tON_MIN Minimum PWM pulse duration, low side, for charging the Bootstrap capacitor TA Operating ambient temperature PVDD_X Half bridge X (A, B, or C) DC supply voltage GVDD_X (1) 8 A 500 kHz 22 200 kΩ 19 200 kΩ 33 220 nF 85 (1) °C 50 -40 ns Depending on power dissipation and heat-sinking, the DRV8312/32 can support ambient temperature in excess of 85°C. Refer to the package heat dissipation ratings table and package power deratings table. PACKAGE HEAT DISSIPATION RATINGS PARAMETER DRV8312 DRV8332 1.1 °C/W 0.9 °C/W RθJA, junction-to-ambient thermal resistance 25 °C/W This device is not intended to be used without a heatsink. Therefore, RθJA is not specified. See the Thermal Information section. Exposed power pad / heat slug area 34 mm2 80 mm2 RθJC, junction-to-case (power pad / heat slug) thermal resistance PACKAGE POWER DERATINGS (DRV8312) (1) PACKAGE TA = 25°C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING TA = 85°C POWER RATING TA = 125°C POWER RATING 44-PIN TSSOP (DDW) 5.0 W 40.0 mW/°C 3.2 W 2.6 W 1.0 W (1) Based on EVM board layout MODE SELECTION PINS MODE PINS M3 M2 M1 OUTPUT CONFIGURATION 1 0 0 1 3PH or 3 HB Three-phase or three half bridges with cycle-by-cycle current limit 1 0 1 1 3PH or 3 HB Three-phase or three half bridges with OC latching shutdown (no cycle-bycycle current limit) 0 x x Reserved 1 1 x Reserved DESCRIPTION Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 3 DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 www.ti.com DEVICE INFORMATION Pin Assignment Here are the pinouts for the DRV8312/32: • DRV8312: 44-pin TSSOP power pad down DDW package. This package contains a thermal pad that is located on the bottom side of the device for dissipating heat through PCB. • DRV8332: 36-pin PSOP3 DKD package. This package contains a thick heat slug that is located on the top side of the device for dissipating heat through heatsink. DRV8332 DKD Package (Top View) DRV8312 DDW Package (Top View) GVDD_C 1 44 VDD NC NC PWM_C 2 43 3 42 4 41 5 40 RESET_C RESET_B M1 M2 M3 VREG AGND GND OC_ADJ PWM_B RESET_A PWM_A FAULT NC NC OTW GVDD_B 6 39 7 38 8 37 9 36 10 35 11 34 12 33 13 32 14 31 15 30 16 29 17 28 18 27 19 26 20 25 21 24 23 22 GVDD_C BST_C NC PVDD_C PVDD_C OUT_C GND_C GND GND NC NC BST_B PVDD_B OUT_B GND_B GND_A OUT_A PVDD_A PVDD_A NC BST_A GVDD_A GVDD_B 1 36 GVDD_A OTW 2 35 BST_A FAULT 3 34 PVDD_A PWM_A 4 33 OUT_A RESET_A 5 32 GND_A PWM_B 6 31 GND_B OC_ADJ 7 30 OUT_B GND 8 29 PVDD_B AGND 9 28 BST_B VREG 10 27 NC M3 11 26 NC M2 12 25 GND M1 13 24 GND RESET_B 14 23 GND_C RESET_C 15 22 OUT_C PWM_C 16 21 PVDD_C VDD 17 20 BST_C GVDD_C 18 19 GVDD_C Pin Functions PIN (1) 4 FUNCTION (1) DESCRIPTION NAME DRV8312 DRV8332 AGND 12 9 P Analog ground BST_A 24 35 P High side bootstrap supply (BST), external capacitor to OUT_A required BST_B 33 28 P High side bootstrap supply (BST), external capacitor to OUT_B required BST_C 43 20 P High side bootstrap supply (BST), external capacitor to OUT_C required GND 13, 36, 37 8 P Ground GND_A 29 32 P Power ground for half-bridge A GND_B 30 31 P Power ground for half-bridge B GND_C 38 23 P Power ground for half-bridge C GVDD_A 23 36 P Gate-drive voltage supply GVDD_B 22 1 P Gate-drive voltage supply GVDD_C 1, 44 18, 19 P Gate-drive voltage supply M1 8 13 I Mode selection pin M2 9 12 I Reserved mode selection pin. AGND connection is recommended M3 10 11 I Reserved mode selection pin, VREG connection is recommended NC 3,4,19,20,25,34,35 ,42 26,27 - No connection pin. Ground connection is recommended OC_ADJ 14 7 O Analog overcurrent programming pin, requires resistor to AGND I = input, O = output, P = power, T = thermal Submit Documentation Feedback Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 PIN FUNCTION (1) DESCRIPTION NAME DRV8312 DRV8332 OTW 21 2 O Overtemperature warning signal, open-drain, active-low. An internal pull-up resistor to VREG (3.3 V) is provided on output. Level compliance for 5-V logic can be obtained by adding external pull-up resistor to 5 V OUT_A 28 33 O Output, half-bridge A OUT_B 31 30 O Output, half-bridge B OUT_C 39 22 O Output, half-bridge C PVDD_A 26,27 34 P Power supply input for half-bridge A requires close decoupling capacitor to ground. PVDD_B 32 29 P Power supply input for half-bridge B requires close decoupling capacitor to gound. PVDD_C 40,41 21 P Power supply input for half-bridge C requires close decoupling capacitor to ground. PWM_A 17 4 I Input signal for half-bridge A PWM_B 15 6 I Input signal for half-bridge B PWM_C 5 16 I Input signal for half-bridge C RESET_A 16 5 I Reset signal for half-bridge A, active-low RESET_B 7 15 I Reset signal for half-bridge B, active-low RESET_C 6 15 I Reset signal for half-bridge C, active-low FAULT 18 3 O Fault signal, open-drain, active-low. An internal pull-up resistor to VREG (3.3 V) is provided on output. Level compliance for 5-V logic can be obtained by adding external pull-up resistor to 5 V VDD 2 17 P Power supply for digital voltage regulator requires capacitor to ground for decoupling. VREG 11 10 P Digital regulator supply filter pin requires 0.1-μF capacitor to AGND. THERMAL PAD -- N/A T Solder the exposed thermal pad at the bottom of the DRV8312DDW package to the landing pad on the PCB. Connect the landing pad through vias to large ground plate for better thermal dissipation. HEAT SLUG N/A -- T Mount heatsink with thermal interface to the heat slug on the top of the DRV8332DKD package to improve thermal dissipation. Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 5 DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 www.ti.com SYSTEM BLOCK DIAGRAM VDD 4 Undervoltage Protection OTW Internal Pullup Resistors to VREG FAULT M1 Protection and I/O Logic M2 M3 4 VREG VREG Power On Reset AGND Temp. Sense GND RESET_A Overload Protection RESET_B Isense OC_ADJ RESET_C GVDD_C BST_C PVDD_C PWM_C PWM Rcv. Ctrl. Timing Gate Drive OUT_C GND_C GVDD_B BST_B PVDD_B PWM_B PWM Rcv. Ctrl. Timing Gate Drive OUT_B GND_B GVDD_A BST_A PVDD_A PWM_A PWM Rcv. Ctrl. Timing Gate Drive OUT_A GND_A 6 Submit Documentation Feedback Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 ELECTRICAL CHARACTERISTICS TA = 25 °C, PVDD = 50 V, GVDD = VDD = 12 V, fSw = 400 kHz, unless otherwise noted. All performance is in accordance with recommended operating conditions unless otherwise specified. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 2.95 3.3 3.65 9 12 mA 2.5 mA 1 mA Internal Voltage Regulator and Current Consumption VREG Voltage regulator, only used as a reference node IVDD VDD = 12 V Idle, reset mode VDD supply current Operating, 50% duty cycle V 10.5 Reset mode 1.7 IGVDD_X Gate supply current per half-bridge IPVDD_X Half-bridge X (A, B, or C) idle current Reset mode 0.7 MOSFET drain-to-source resistance, low side (LS) TJ = 25°C, GVDD = 12 V 80 mΩ MOSFET drain-to-source resistance, high side (HS) TJ = 25°C, GVDD = 12 V 80 mΩ VF Diode forward voltage drop TJ = 25°C - 125°C, IO = 5 A tR Output rise time tF tPD_ON Operating, 50% duty cycle 8 Output Stage RDS(on) 1 V Resistive load, IO = 5 A 14 ns Output fall time Resistive load, IO = 5 A 14 ns Propagation delay when FET is on Resistive load, IO = 5 A 38 ns tPD_OFF Propagation delay when FET is off Resistive load, IO = 5 A 38 ns tDT Dead time between HS and LS FETs Resistive load, IO = 5 A 5.5 ns 8.5 V I/O Protection Gate supply voltage GVDD_X undervoltage protection threshold Vuvp,G Vuvp,hyst (1) Hysteresis for gate supply undervoltage event OTW (1) Overtemperature warning OTWhyst (1) Hysteresis temperature to reset OTW event OTSD (1) Overtemperature shut down OTEOTWdifferential (1) 0.8 115 125 V 135 °C 25 °C 150 °C OTE-OTW overtemperature detect temperature difference 25 °C OTSDHYST (1) Hysteresis temperature for FAULT to be released following an OTSD event 25 °C IOC Overcurrent limit protection Resistor—programmable, nominal, ROCP = 27 kΩ 9.7 A Overcurrent response time Time from application of short condition to Hi-Z of affected FET(s) 250 ns IOCT Static Digital Specifications VIH High-level input voltage PWM_A, PWM_B, PWM_C, M1, M2, M3 2 3.6 V VIH High-level input voltage RESET_A, RESET_B, RESET_C 2 3.6 V VIL Low-level input voltage PWM_A, PWM_B, PWM_C, M1, M2, M3, RESET_A, RESET_B, RESET_C 0.8 V llkg Input leakage current 100 μA kΩ -100 OTW / FAULT RINT_PU Internal pullup resistance, OTW to VREG, FAULT to VREG VOH High-level output voltage VOL Low-level output voltage (1) Internal pullup resistor only External pullup of 4.7 kΩ to 5 V IO = 4 mA 20 26 35 2.95 3.3 3.65 4.5 5 0.2 0.4 V V Specified by design Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 7 DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 www.ti.com TYPICAL CHARACTERISTICS EFFICIENCY vs SWITCHING FREQUENCY (DRV8332) NORMALIZED RDS(on) vs GATE DRIVE 1.10 100 TJ = 25°C Normalized RDS(on) / (RDS(on) at 12 V) 90 80 Efficiency – % 70 60 50 40 30 Full Bridge 20 Load = 5 A PVDD = 50 V TC = 75°C 10 0 0 50 1.08 1.06 1.04 1.02 1.00 0.98 0.96 8.0 100 150 200 250 300 350 400 450 500 8.5 9.0 f – Switching Frequency – kHz Figure 1. NORMALIZED RDS(on) vs JUNCTION TEMPERATURE 10.5 11.0 11.5 12 6 TJ = 25°C GVDD = 12 V 5 1.4 4 1.2 I – Current – A Normalized RDS(on) / (RDS(on) at 25oC) 10.0 DRAIN TO SOURCE DIODE FORWARD ON CHARACTERISTICS 1.6 1.0 3 2 0.8 1 0.6 0.4 –40 –20 0 0 20 40 60 80 100 120 140 –1 0 0.2 o Submit Documentation Feedback 0.4 0.6 0.8 1 1.2 V – Voltage – V Figure 4. TJ – Junction Temperature – C Figure 3. 8 9.5 GVDD – Gate Drive – V Figure 2. Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 TYPICAL CHARACTERISTICS (continued) OUTPUT DUTY CYCLE vs INPUT DUTY CYCLE 100 fS = 500 kHz TC = 25°C 90 Output Duty Cycle – % 80 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 Input Duty Cycle – % Figure 5. Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 9 DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 www.ti.com THEORY OF OPERATION POWER SUPPLIES To facilitate system design, the DRV8312/32 need only a 12-V supply in addition to H-Bridge power supply (PVDD). An internal voltage regulator provides suitable voltage levels for the digital and low-voltage analog circuitry. Additionally, the high-side gate drive requiring a floating voltage supply, which is accommodated by built-in bootstrap circuitry requiring external bootstrap capacitor. Special attention should be paid to the power-stage power supply; this includes component selection, PCB placement, and routing. As indicated, each halfbridge has independent power-stage supply pin (PVDD_X). For optimal electrical performance, EMI compliance, and system reliability, it is important that each PVDD_X pin is decoupled with a ceramic capacitor (X5R or better) placed as close as possible to each supply pin. It is recommended to follow the PCB layout of the DRV8312/32 EVM board. To provide symmetrical electrical characteristics, the PWM signal path, including gate drive and output stage, is designed as identical, independent halfbridges. For this reason, each half-bridge has a separate gate drive supply (GVDD_X), a bootstrap pin (BST_X), and a power-stage supply pin (PVDD_X). Furthermore, an additional pin (VDD) is provided as supply for all common circuits. Special attention should be paid to place all decoupling capacitors as close to their associated pins as possible. In general, inductance between the power supply pins and decoupling capacitors must be avoided. Furthermore, decoupling capacitors need a short ground path back to the device. The 12-V supply should be from a low-noise, lowoutput-impedance voltage regulator. Likewise, the 50V power-stage supply is assumed to have low output impedance and low noise. The power-supply sequence is not critical as facilitated by the internal power-on-reset circuit. Moreover, the DRV8312/32 are fully protected against erroneous power-stage turn-on due to parasitic gate charging. Thus, voltagesupply ramp rates (dv/dt) are non-critical within the specified voltage range (see the Recommended Operating Conditions section of this data sheet). For a properly functioning bootstrap circuit, a small ceramic capacitor (an X5R or better) must be connected from each bootstrap pin (BST_X) to the power-stage output pin (OUT_X). When the powerstage output is low, the bootstrap capacitor is charged through an internal diode connected between the gate-drive power-supply pin (GVDD_X) and the bootstrap pin. When the power-stage output is high, the bootstrap capacitor potential is shifted above the output potential and thus provides a suitable voltage supply for the high-side gate driver. In an application with PWM switching frequencies in the range from 10 kHz to 500 kHz, the use of 100-nF ceramic capacitors (X5R or better), size 0603 or 0805, is recommended for the bootstrap supply. These 100-nF capacitors ensure sufficient energy storage, even during minimal PWM duty cycles, to keep the high-side power stage FET fully turned on during the remaining part of the PWM cycle. In an application running at a switching frequency lower than 10 kHz, the bootstrap capacitor might need to be increased in value. Powering Up 10 Submit Documentation Feedback SYSTEM POWER-UP/POWER-DOWN SEQUENCE The DRV8312/32 do not require a power-up sequence. The outputs of the H-bridges remain in a high impedance state until the gate-drive supply voltage GVDD_X and VDD voltage are above the undervoltage protection (UVP) voltage threshold (see the Electrical Characteristics section of this data sheet). Although not specifically required, holding RESET_A, RESET_B, and RESET_C in a low state while powering up the device is recommended. This allows an internal circuit to charge the external bootstrap capacitors by enabling a weak pulldown of the half-bridge output. Powering Down The DRV8312/32 do not require a power-down sequence. The device remains fully operational as long as the gate-drive supply (GVDD_X) voltage and VDD voltage are above the UVP voltage threshold (see the Electrical Characteristics section of this data sheet). Although not specifically required, it is a good practice to hold RESET_A, RESET_B and RESET_C low during power down to prevent any unknown state during this transition. Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 ERROR REPORTING Bootstrap Capacitor Under Voltage Protection The FAULT and OTW pins are both active-low, opendrain outputs. Their function is for protection-mode signaling to a PWM controller or other system-control device. When the device runs at a low switching frequency (e.g. less than 10 kHz with a 100-nF bootstrap capacitor), the bootstrap capacitor voltage might not be able to maintain a proper voltage level for the high-side gate driver. A bootstrap capacitor undervoltage protection circuit (BST_UVP) will prevent potential failure of the high-side MOSFET. When the voltage on the bootstrap capacitors is less than the required value for safe operation, the DRV8312/32 will initiate bootstrap capacitor recharge sequences (turn off high side FET for a short period) until the bootstrap capacitors are properly charged for safe operation. This function may also be activated when PWM duty cycle is too high (e.g. less than 20 ns off time at 10 kHz). Note that bootstrap capacitor might not be able to be charged if no load or extremely light load is presented at output during BST_UVP operation, so it is recommended to turn on the low side FET for at least 50 ns for each PWM cycle to avoid BST_UVP operation if possible. Any fault resulting in device shutdown, such as overtemperatue shut down, overcurrent shut-down, or undervoltage protection, is signaled by the FAULT pin going low. Likewise, OTW goes low when the device junction temperature exceeds 125°C (see Table 1). Table 1. Protection Mode Signal Descriptions FAULT OTW DESCRIPTION 0 0 Overtemperature warning and (overtemperature shut down or overcurrent shut down or undervoltage protection) occurred 0 1 Overcurrent shut-down or GVDD undervoltage protection occurred 1 0 Overtemperature warning 1 1 Device under normal operation TI recommends monitoring the OTW signal using the system microcontroller and responding to an OTW signal by reducing the load current to prevent further heating of the device resulting in device overtemperature shutdown (OTSD). To reduce external component count, an internal pullup resistor to internal VREG (3.3 V) is provided on both FAULT and OTW outputs. Level compliance for 5-V logic can be obtained by adding external pull-up resistors to 5 V (see the Electrical Characteristics section of this data sheet for further specifications). DEVICE PROTECTION SYSTEM The DRV8312/32 contain advanced protection circuits carefully designed to facilitate system integration and ease of use, as well as to safeguard the device from permanent failure due to a wide range of fault conditions such as short circuits, overcurrent, overtemperature, and undervoltage. The DRV8312/32 respond to a fault by immediately setting the half bridge outputs in a high-impedance (Hi-Z) state and asserting the FAULT pin low. In situations other than overcurrent or overtemperature, the device automatically recovers when the fault condition has been removed or the gate supply voltage has increased. For highest possible reliability, reset the device externally no sooner than 1 second after the shutdown when recovering from an overcurrent shut down (OCSD) or OTSD fault. For applications with lower than 10 kHz switching frequency and not to trigger BST_UVP protection, a larger bootstrap capacitor can be used (e.g., 1 uF cap for 800 Hz operation). When using a bootstrap cap larger than 220 nF, it is recommended to add 5 ohm resistors between 12V GVDD power supply and GVDD_X pins to limit the inrush current on the internal bootstrap diodes. Overcurrent (OC) Protection The DRV8312/32 have independent, fast-reacting current detectors with programmable trip threshold (OC threshold) on all high-side and low-side powerstage FETs. There are two settings for OC protection through mode selection pins: cycle-by-cycle (CBC) current limiting mode and OC latching (OCL) shut down mode. In CBC current limiting mode, the detector outputs are monitored by two protection systems. The first protection system controls the power stage in order to prevent the output current from further increasing, i.e., it performs a CBC current-limiting function rather than prematurely shutting down the device. This feature can effectively limit the inrush current during motor start-up or transient without damaging the device. During short to power and short to ground conditions, since the current limit circuitry might not be able to control the current to a proper level, a second protection system triggers a latching shutdown, resulting in the related half bridge being set in the high-impedance (Hi-Z) state. Current limiting and overcurrent protection are independent for half-bridges A, B, and C, respectively. Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 11 DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 www.ti.com Figure 6 illustrates cycle-by-cycle operation with high side OC event and Figure 7 shows cycle-by-cycle operation with low side OC. Dashed lines are the operation waveforms when no CBC event is triggered and solide lines show the waveforms when CBC event is triggered. In CBC current limiting mode, when low side FET OC is detected, the device will turn off the affected low side FET and keep the high side FET at the same half bridge off until next PWM cycle; when high side FET OC is detected, the device will turn off the affected high side FET and turn on the low side FET at the half bridge until next PWM cycle. It is important to note that if the input to a half bridge is held to a constant value when an over current event occurs in CBC, then the associated half bridge will be in a HI-Z state upon the over current event ending. Cycling IN_X will allow OUT_X to resume normal operation. In OC latching shut down mode, the CBC current limit and error recovery circuits are disabled and an overcurrent condition will cause the device to shutdown. After shutdown, RESET_A, RESET_B, and RESET_C must be asserted to restore normal operation after the overcurrent condition is removed. For added flexibility, the OC threshold is programmable using a single external resistor connected between the OC_ADJ pin and AGND pin. See Table 2 for information on the correlation between programming-resistor value and the OC threshold. The values in Table 2 show typical OC thresholds for a given resistor. Assuming a fixed resistance on the OC_ADJ pin across multiple devices, a 20% deviceto-device variation in OC threshold measurements is possible. Therefore, this feature is designed for system protection and not for precise current control. Table 2. Programming-Resistor Values and OC Threshold OC-ADJUST RESISTOR VALUES (kΩ) 19 (1) 12 MAXIMUM CURRENT BEFORE OC OCCURS (A) (1) 13.2 22 11.6 24 10.7 27 9.7 30 8.8 36 7.4 39 6.9 43 6.3 Table 2. Programming-Resistor Values and OC Threshold (continued) OC-ADJUST RESISTOR VALUES (kΩ) MAXIMUM CURRENT BEFORE OC OCCURS (A) 47 5.8 56 4.9 68 4.1 82 3.4 100 2.8 120 2.4 150 1.9 200 1.4 It should be noted that a properly functioning overcurrent detector assumes the presence of a proper inductor or power ferrite bead at the powerstage output. Short-circuit protection is not ensured with a direct short at the output pins of the power stage. Overtemperature Protection The DRV8312/32 have a two-level temperatureprotection system that asserts an active-low warning signal (OTW) when the device junction temperature exceeds 125°C (nominal) and, if the device junction temperature exceeds 150°C (nominal), the device is put into thermal shutdown, resulting in all half-bridge outputs being set in the high-impedance (Hi-Z) state and FAULT being asserted low. OTSD is latched in this case and RESET_A, RESET_B, and RESET_C must be asserted low to clear the latch. Undervoltage Protection (UVP) and Power-On Reset (POR) The UVP and POR circuits of the DRV8312/32 fully protect the device in any power-up / down and brownout situation. While powering up, the POR circuit resets the overcurrent circuit and ensures that all circuits are fully operational when the GVDD_X and VDD supply voltages reach 9.8 V (typical). Although GVDD_X and VDD are independently monitored, a supply voltage drop below the UVP threshold on any VDD or GVDD_X pin results in all half-bridge outputs immediately being set in the highimpedance (Hi-Z) state and FAULT being asserted low. The device automatically resumes operation when all supply voltage on the bootstrap capacitors have increased above the UVP threshold. Recommended to use in OC Latching Mode Only Submit Documentation Feedback Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 DEVICE RESET Three reset pins are provided for independent control of half-bridges A, B, and C. When RESET_X is asserted low, two power-stage FETs in half-bridges X are forced into a high-impedance (Hi-Z) state. A rising-edge transition on reset input allows the device to resume operation after a shut-down fault. That is, when half-bridge X has OC shutdown in CBC mode, a low to high transition of RESET_X pin will clear the fault and FAULT pin. When an OTSD or OC shutdown in Latching mode occurs, all three RESET_A, RESET_B, and RESET_C need to have a low to high transition to clear the fault and reset FAULT signal. DIFFERENT OPERATIONAL MODES The DRV8312/32 support two different modes of operation: 1. Three-phase (3PH) or three half bridges (HB) with CBC current limit 2. Three-phase or three half bridges with OC latching shutdown (no CBC current limit) Because each half bridge has independent supply and ground pins, a shunt sensing resistor can be inserted between PVDD to PVDD_X or GND_X to GND (ground plane). A high side shunt resistor between PVDD and PVDD_X is recommended for differential current sensing because a high bias voltage on the low side sensing could affect device operation. If low side sensing has to be used, a shunt resistor value of 10 mΩ or less or sense voltage 100 mV or less is recommended. Figure 8 and Figure 9 show the three-phase application examples, and Figure 10 shows how to connect to DRV8312/32 with some simple logic to accommodate conventional 6 PWM inputs control. We recommend using a complementary control scheme for switching phases to prevent circulated energy flowing inside the phases and to make current limiting feature active all the time. Complementary control scheme also forces the current flowing through sense resistors all the time to have a better current sensing and control of the system. Figure 11 shows six steps trapezoidal scheme with hall sensor control and Figure 12 shows six steps trapezoidal scheme with sensorless control. The hall sensor sequence in real application might be different than the one we showed in Figure 11 depending on the motor used. Please check motor manufacture datasheet for the right sequence in applications. In six step trapezoidal complementary control scheme, a half bridge with larger than 50% duty cycle will have a positive current and a half bridge with less than 50% duty cycle will have a negative current. For normal operation, changing PWM duty cycle from 50% to 100% will adjust the current from 0 to maximum value with six steps control. It is recommanded to apply a minimum 50ns to 100 ns PWM pulse at each switching cycle at lower side to properly charge the bootstrap cap. The impact of minimum pulse at low side FET is pretty small, e.g., the maximum duty cycle is 99.9% with 100ns minimum pulse on low side. RESET_Xpin can be used to get channel X into high impedance mode. If you prefer PWM switching one channel but hold low side FET of the other channel on (and third channel in Hi-Z) for 2-quadrant mode, OT latching shutdown mode is recommended to prevent the channel with low side FET on stuck in Hi-Z during OC event in CBC mode. The DRV8312/32 can also be used for sinusoidal waveform control and field oriented control. Please check TI website MCU motor control library for control algorithms. Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 13 DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 www.ti.com CBC with High Side OC During T_OC Period PVDD Current Limit Load Current PWM_HS Load PWM_LS PWM_HS PWM_LS GND_X T_HS T_OC T_LS Figure 6. Cycle-by-Cycle Operation with High Side OC (dashed line: normal operation; solid line: CBC event) During T_OC Period CBC with Low Side OC PVDD Current Limit Load Current PWM_HS Load PWM_LS GND_X PWM_HS PWM_LS T_LS T_OC T_HS Figure 7. Cycle-by-Cycle Operation with Low Side OC (dashed line: normal operation; solid line: CBC event) 14 Submit Documentation Feedback Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 GVDD PVDD 1 mF DRV8332 330 mF 3.3 1000 mF GVDD_B 1mF OTW GVDD_A 10 nF BST_A 100 nF FAULT PVDD_A PWM_A OUT_A RESET_A GND_A Loc Rsense_A 100nF M Rsense_B Controller (MSP430 C2000 or Stellaris MCU) PWM_B GND_B Loc Roc_adj OC_ADJ 1 GND OUT_B PVDD_B AGND BST_B VREG NC M3 NC M2 GND 100 nF 100nF 100 nF M1 Rsense_x £ 10 mW or Vsense < 100 mV GND Rsense_C RESET_B GND_C RESET_C OUT_C PWM_C GVDD VDD Loc PVDD_C BST_C 100 nF 1 mF 47 mF GVDD_C GVDD_C 100nF PVDD 1mF Figure 8. DRV8332 Application Diagram for Three-Phase Operation Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 15 DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 www.ti.com 1mF DRV8312 GVDD GVDD_B 330 mF GVDD_A PVDD 100 nF 1mF BST_A 3.3 NC NC 10 nF NC PVDD_A FAULT PVDD_A OTW 1000 mF Controller (MSP430 C2000 or Stellaris MCU) PWM_A OUT_A RESET_A GND_A PWM_B GND_B Loc Rsense_A 100nF M Rsense_B Loc Roc_adj OC_ADJ OUT_B 1 GND PVDD_B AGND BST_B VREG NC M3 NC 100 nF 100nF 100 nF M2 GND M1 GND Rsense_x £ 10 mW or Vsense < 100 mV Rsense_C GVDD 1mF 47 mF RESET_B GND_C RESET_C OUT_C PWM_C PVDD_C NC PVDD_C NC NC VDD GVDD_C Loc 100nF PVDD BST_C 100 nF GVDD_C 1mF Figure 9. DRV8312 Application Diagram for Three-Phase Operation PVDD Controller PWM_AH PWM_BH PWM_CH PWM_A PWM_B PWM_C MOTOR OUT_A OUT_B RESET_A OUT_C PWM_AL RESET_B PWM_BL RESET_C PWM_CL GND_A GND_B GND_C Figure 10. Control Signal Logic with Conventional 6 PWM Input Scheme 16 Submit Documentation Feedback Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 S1 S2 S3 S4 S5 S6 S1 S2 S3 S4 S5 S6 Hall Sensor H1 Hall Sensor H2 Hall Sensor H3 Phase Current A Phase Current B Phase Current C PWM_A PWM_B PWM_C RESET_A RESET_B RESET_C 360 o PWM= 100% 360 o PWM=75% Figure 11. Hall Sensor Control with 6 Steps Trapezoidal Scheme Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 17 DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 S1 Back EMF (Vab) Back EMF (Vbc) Back EMF (Vca) www.ti.com S2 S3 S4 S5 S6 S1 S2 S3 S4 S5 S6 0V 0V 0V Phase A Current and Voltage Va Ia 0A 0V Phase B Current and Voltage Vb Ib 0A 0V Vc Phase C Current and Voltage Ic 0A 0V PWM_A PWM_B PWM_C RESET_A RESET_B RESET_C 360 o 360 PWM= 100% o PWM= 75% Figure 12. Sensorless Control with 6 Steps Trapezoidal Scheme 18 Submit Documentation Feedback Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 APPLICATION INFORMATION SYSTEM DESIGN RECOMMENDATIONS Voltage of Decoupling Capacitor The voltage of the decoupling capacitors should be selected in accordance with good design practices. Temperature, ripple current, and voltage overshoot must be considered. The high frequency decoupling capacitor should use ceramic capacitor with X5R or better rating. For a 50-V application, a minimum voltage rating of 63 V is recommended. Current Requirement of 12V Power Supply The DRV8312/32 require a 12V power supply for GVDD and VDD pins. The total supply current is pretty low at room temp (less than 50mA), but the current could increase significantly when the device temperature goes too high (e.g. above 125°C), especially at heave load conditions due to substrate current collection by 12V guard rings. So it is recommended to design the 12V power supply with current capability at least 5-10% of your load current and no less than 100mA to assure the device performance across all temperature range. VREG Pin The VREG pin is used for internal logic and should not be used as a voltage source for external circuitries. The capacitor on VREG pin should be connected to AGND. VDD Pin The transient current in VDD pin could be significantly higher than average current through VDD pin. A low resistive path to GVDD should be used. A 22-µF to 47-µF capacitor should be placed on VDD pin beside the 100-nF to 1-µF decoupling capacitor to provide a constant voltage during transient. OTW Pin OTW reporting indicates the device approaching high junction temperature. This signal can be used with MCU to decrease system power when OTW is low in order to prevent OT shut down at a higher temperature. No external pull up resistor or 3.3V power supply is needed for 3.3V logic. The OTW pin has an internal pullup resistor connecting to an internal 3.3V to reduce external component count. For 5V logic, an external pull up resistor to 5V is needed. FAULT Pin The FAULT pin reports any fault condition resulting in device shut down. No external pull up resistor or 3.3V power supply is needed for 3.3V logic. The FAULT pin has an internal pullup resistor connecting to an internal 3.3V to reduce external component count. For 5V logic, an external pull upresistor to 5V is needed. OC_ADJ Pin For accurate control of the overcurrent protection, the OC_ADJ pin has to be connected to AGND through an OC adjust resistor. PWM_X and RESET_X Pins It is recommanded to connect these pins to either AGND or GND when they are not used, and these pins only support 3.3V logic. Mode Select Pins Mode select pins (M1, M2, and M3) should be connected to either VREG (for logic high) or AGND for logic low. It is not recommended to connect mode pins to board ground if 1-Ω resistor is used between AGND and GND. Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 19 DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 www.ti.com Output Inductor Selection For normal operation, inductance in motor (assume larger than 10 µH) is sufficient to provide low di/dt output (e.g. for EMI) and proper protection during overload condition (CBC current limiting feature). So no additional output inductors are needed during normal operation. However during a short condition, the motor (or other load) could be shorted, so the load inductance might not present in the system anymore; the current in short condition can reach such a high level that may exceed the abs max current rating due to extremely low impendence in the short circuit path and high di/dt before oc detection circuit kicks in. So a ferrite bead or inductor is recommended to utilize the short circuit protection feature in DRV8312/32. With an external inductor or ferrite bead, the current will rise at a much slower rate and reach a lower current level before oc protection starts. The device will then either operate CBC current limit or OC shut down automatically (when current is well above the current limit threshold) to protect the system. For a system that has limited space, a power ferrite bead can be used instead of an inductor. The current rating of ferrite bead has to be higher than the RMS current of the system at normal operation. A ferrite bead designed for very high frequency is NOT recommended. A minimum impedance of 10 Ω or higher is recommended at 10 MHz or lower frequency to effectively limit the current rising rate during short circuit condition. The TDK MPZ2012S300A and MPZ2012S101A (with size of 0805 inch type) have been tested in our system to meet short circuit conditions in the DRV8312. But other ferrite beads that have similar frequency characteristics can be used as well. For higher power applications, such as in the DRV8332, there might be limited options to select suitable ferrite bead with high current rating. If an adequate ferrite bead cannot be found, an inductor can be used. The inductance can be calculated as: PVDD × Toc _ delay Loc _ min = Ipeak - Iave (1) Where Toc_delay = 250 nS, Ipeak = 15 A (below abs max rating). Because an inductor usually saturates pretty quickly after reaching its current rating, it is recommended to use an inductor with a doubled value or an inductor with a current rating well above the operating condition. PCB LAYOUT RECOMMENDATION PCB Material Recommendation FR-4 Glass Epoxy material with 2 oz. copper on both top and bottom layer is recommended for improved thermal performance (better heat sinking) and less noise susceptibility (lower PCB trace inductance). Ground Plane Because of the power level of these devices, it is recommended to use a big unbroken single ground plane for the whole system / board. The ground plane can be easily made at bottom PCB layer. In order to minimize the impedance and inductance of ground traces, the traces from ground pins should keep as short and wide as possible before connected to bottom ground plane through vias. Multiple vias are suggested to reduce the impedance of vias. Try to clear the space around the device as much as possible especially at bottom PCB side to improve the heat spreading. Decoupling Capacitor High frequency decoupling capacitors (100 nF) should be placed close to PVDD_X pins and with a short ground return path to minimize the inductance on the PCB trace. AGND AGND is a localized internal ground for logic signals. A 1-Ω resistor is recommended to be connected between GND and AGND to isolate the noise from board ground to AGND. There are other two components are connected to this local ground: 0.1-µF capacitor between VREG to AGND and Roc_adj resistor between OC_ADJ and AGND. Capacitor for VREG should be placed close to VREG and AGND pins and connected without vias. 20 Submit Documentation Feedback Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 Current Shunt Resistor If current shunt resistor is connected between GND_X to GND or PVDD_X to PVDD, make sure there is only one single path to connect each GND_X or PVDD_X pin to shunt resistor, and the path is short and symmetrical on each sense path to minimize the measurement error due to additional resistance on the trace. PCB LAYOUT EXAMPLE An example of the schematic and PCB layout of DRV8312 are shown in Figure 13, Figure 14, and Figure 15. Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 21 22 U1 Submit Documentation Feedback 1 3 1 3 2 1 3 2 RSTB 2 1 3 GVDD RSTC M1 GND HTSSOP44-DDW PowerPad S1 2 Product Folder Links: DRV8312 DRV8332 GVDD GVDD GND Orange Orange Orange Orange 0603 1.0ufd/16V 0603 C34 GND 1.0ufd/16V 0603 C35 GND 47K R37 1.0 1/4W 0805 R36 0.1ufd/16V 0603 C33 Orange 1.0ufd/16V 0603 47ufd/16V M GND C32 GND C31 GND + 1.0ufd/16V 0603 C30 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 HTSSOP44-DDW DRV8312DDW U1 44 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 GND 0.1ufd/100V 0805 C45 0.1ufd/100V 0805 C42 0.1ufd/100V 0805 C36 PVDD PVDD GND 0.1ufd/100V 0805 C46 GND 0.1ufd/100V 0805 C43 GND 0.1ufd/100V 0805 C37 PVDD OUT_C Orange OUT_A Orange OUT_B Orange L2 30ohms/6A 0805 L4 30ohms/6A 0805 L3 30ohms/6A 0805 0.0 0603 R21 0.0 0603 R20 0.0 0603 R23 0.0 0603 R22 +3.3V +3.3V R18 R19 5 V- 5 1 2 V+ V+ GND 499 0603 R39 +3.3V +3.3V GND R63 R64 OA4 +IN -IN 10.2K 0603 R27 10.2K 0603 R26 SOT23-DBV OPA365AIDBV V+ VOUT V- 0.1ufd/16V 0603 C39 5 1 2 SOT23-DBV +IN -IN OPA365AIDBV V+ VOUT OA3 C19 +2.5V IS-IhbC 30.1K 0603 R41 220pfd/50V 0603 C20 3 4 3 619 0603 R31 15.4K 0603 R55 619 0603 R30 15.4K 0603 R54 0.01 1W 1206 0.01 1W 1206 IS 30.1K 0603 R62 220pfd/50V 0603 C22 +2.5V 30.1K 0603 R16 220pfd/50V 0603 C21 +2.5V GND GND GND 0.005 1W 1206 R51 OUTC 220pfd/50V 0603 C28 931 0603 R34 220pfd/50V 0603 C27 931 0603 R35 1000pfd/50V 0603 C60 IS-IhbB 1000pfd/50V 0603 C59 IS-IhbA OUTA OUTB ROUTED GROUND (SHIELDED FROM GND PLANE) IS-TOTAL 1000pfd/50V 0603 C58 IS-IhbC 1000pfd/50V 0603 C57 IS-TOTAL STUFF OPTION R53 R52 4 220pfd/50V 0603 C26 931 0603 R33 220pfd/50V 0603 C25 931 0603 R32 STUFF OPTION IS-IhbA -IhbB 0.01 1W 1206 GND GND +2.5V 30.1K 0603 R40 220pfd/50V 0603 R50 619 0603 R29 15.4K 0603 R49 619 0603 R28 15.4K 0603 R48 SLES256D – MAY 2010 – REVISED JANUARY 2014 GND 33 1/8W 0805 5 1 V- 0.1ufd/16V 0603 C29 GND GND 33 1/8W 0805 GND 2 GND 1000pfd/100V 0603 C56 ADC-Vhb2 GND 1000pfd/100V 0603 GND 10.2K 0603 R25 3 4 3 4 1000pfd/100V 0603 C50 10.2K 0603 R24 SOT23-DBV C55 GND 499 0603 499 0603 +IN -IN OPA365AIDBV R43 R45 OA2 SOT23-DBV VOUT V- 10.0K 0603 10.0K 0603 +IN -IN OPA365AIDBV R42 R44 OA1 VOUT 0.1ufd/16V 0603 C24 10.0K 0603 R38 GND 33 1/8W 0805 2 1 0.1ufd/16V 0603 C23 GND GND 33 1/8W 0805 GND DRV8312 DRV8332 www.ti.com Figure 13. DRV8312 Schematic Example Copyright © 2010–2014, Texas Instruments Incorporated DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 C37 T3 T4 T2 C33 T1 C43 C46 T1: PVDD decoupling capacitors C37, C43, and C46 should be placed very close to PVDD_X pins and ground return path. T2: VREG decoupling capacitor C33 should be placed very close to VREG abd AGND pins. T3: Clear the space above and below the device as much as possible to improve the thermal spreading. T4: Add many vias to reduce the impedance of ground path through top to bottom side. Make traces as wide as possible for ground path such as GND_X path. Figure 14. Printed Circuit Board – Top Layer B1 B1: Do not block the heat transfer path at bottom side. Clear as much space as possible for better heat spreading. Figure 15. Printed Circuit Board – Bottom Layer Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 23 DRV8312 DRV8332 SLES256D – MAY 2010 – REVISED JANUARY 2014 www.ti.com THERMAL INFORMATION The thermally enhanced package provided with the DRV8332 is designed to interface directly to heat sink using a thermal interface compound in between, (e.g., Ceramique from Arctic Silver, TIMTronics 413, etc.). The heat sink then absorbs heat from the ICs and couples it to the local air. It is also a good practice to connect the heatsink to system ground on the PCB board to reduce the ground noise. RθJA is a system thermal resistance from junction to ambient air. As such, it is a system parameter with the following components: • RθJC (the thermal resistance from junction to case, or in this example the power pad or heat slug) • Thermal grease thermal resistance • Heat sink thermal resistance The thermal grease thermal resistance can be calculated from the exposed power pad or heat slug area and the thermal grease manufacturer's area thermal resistance (expressed in °C-in 2/W or °C-mm2/W). The approximate exposed heat slug size is as follows: • DRV8332, 36-pin PSOP3 …… 0.124 in2 (80 mm 2) The thermal resistance of a thermal pad is considered higher than a thin thermal grease layer and is not recommended. Thermal tape has an even higher thermal resistance and should not be used at all. Heat sink thermal resistance is predicted by the heat sink vendor, modeled using a continuous flow dynamics (CFD) model, or measured. Thus the system RθJA = RθJC + thermal grease resistance + heat sink resistance. See the TI application report, IC Package Thermal Metrics (SPRA953A), for more thermal information. DRV8312 Thermal Via Design Recommendation Thermal pad of the DRV8312 is attached at bottom of device to improve the thermal capability of the device. The thermal pad has to be soldered with a very good coverage on PCB in order to deliver the power specified in the datasheet. The figure below shows the recommended thermal via and land pattern design for the DRV8312. For additional information, see TI application report, PowerPad Made Easy (SLMA004B) and PowerPad Layout Guidelines (SOLA120). Figure 16. DRV8312 Thermal Via Footprint 24 Submit Documentation Feedback Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 DRV8312 DRV8332 www.ti.com SLES256D – MAY 2010 – REVISED JANUARY 2014 REVISION HISTORY Changes from Original (May 2010) to Revision A • Page Changed text in the OC_ADJ Pin section From: "For accurate control of the oevercurrent protection..." To: "For accurate control of the overcurrent protection..." ................................................................................................................ 19 Changes from Revision A (July 2013) to Revision B • Page Changed the description of pin M3 From: AGND connection is recommended To: VREG connection is recommended ....................................................................................................................................................................... 4 Changes from Revision B (September 2013) to Revision C Page • Changed text in the Overcurrent (OC) Protection section From: "cause the device to shutdown immediately." To: "cause the device to shutdown." ......................................................................................................................................... 12 • Changed text in the Overcurrent (OC) Protection section From: "RESET_B, and / or RESET_C must be asserted." To: "RESET_B, and RESET_C must be asserted" ............................................................................................................ 12 • Changed paragraph in the DEVICE RESET "A rising-edge transition..." ........................................................................... 13 Changes from Revision C (October 2013) to Revision D Page • Added the THERMAL INFORMATION table ........................................................................................................................ 2 • Changed the tON_MIN description to include "for charging the Bootstrap capacitor" .............................................................. 3 • Changed GND_A, GND_B, and GND_C pins description to remove text "requires close decoupling capacitor to ground" .................................................................................................................................................................................. 4 • Changed M2 pin description From: Mode selection pin ....................................................................................................... 4 • Added text to the Overcurrent (OC) Protection section - "It is important to note..." ........................................................... 12 • Added text to the Overcurrent (OC) Protection section - "The values in Table 2 show typical..." ...................................... 12 Copyright © 2010–2014, Texas Instruments Incorporated Product Folder Links: DRV8312 DRV8332 Submit Documentation Feedback 25 PACKAGE OPTION ADDENDUM www.ti.com 26-Feb-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) DRV8312DDW ACTIVE HTSSOP DDW 44 35 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DRV8312 DRV8312DDWR ACTIVE HTSSOP DDW 44 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 85 DRV8312 DRV8332DKD ACTIVE HSSOP DKD 36 29 Green (RoHS & no Sb/Br) CU NIPDAU Level-4-260C-72 HR -40 to 85 DRV8332 DRV8332DKDR ACTIVE HSSOP DKD 36 500 Green (RoHS & no Sb/Br) CU NIPDAU Level-4-260C-72 HR -40 to 85 DRV8332 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 26-Feb-2014 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF DRV8332 : NOTE: Qualified Version Definitions: Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 20-Dec-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) DRV8312DDWR HTSSOP DDW 44 2000 330.0 24.4 DRV8332DKDR HSSOP DKD 36 500 330.0 24.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 8.6 15.6 1.8 12.0 24.0 Q1 14.7 16.4 4.0 20.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Dec-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DRV8312DDWR HTSSOP DDW 44 2000 367.0 367.0 45.0 DRV8332DKDR HSSOP DKD 36 500 367.0 367.0 45.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: DRV8312-69M-KIT