November 8, 2011 SHIELDED SMD INDUCTOR DR340-6 SERIES Features Low Profile Surface Mount Design Low Radiation (with magnetic shield) Inductance Range from 2.9µH to 330µH Operating Temperature Range: -20°C to +80°C Tinned Leads with Leaded Solder is Available (note 7) ELECTRICAL SPECIFICATIONS AT 25°C Part Number Inductance (µH) DR340-6-292 DR340-6-402 DR340-6-552 DR340-6-103 DR340-6-123 DR340-6-153 DR340-6-183 DR340-6-223 DR340-6-273 DR340-6-333 DR340-6-393 DR340-6-473 DR340-6-563 DR340-6-683 DR340-6-823 DR340-6-104 DR340-6-124 DR340-6-154 DR340-6-184 DR340-6-224 DR340-6-274 DR340-6-334 2.9 +40% -20% 4.0 +40% -20% 5.5 +40% -20% 10 20% 12 20% 15 20% 18 20% 22 20% 27 20% 33 20% 39 20% 47 20% 56 20% 68 20% 82 20% 100 20% 120 20% 150 20% 180 20% 220 20% 270 20% 330 20% Rated DC Measuring DCR (Ohm) Max. Current (A) Max. Frequency @ 0.25V 7.96MHz 7.96MHz 7.96MHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 1KHz 0.068 0.080 0.096 0.15 0.2 0.23 0.27 0.34 0.38 0.45 0.49 0.69 0.78 1.07 1.21 1.39 1.90 2.18 2.77 3.12 4.38 4.94 1.94 1.63 1.40 1.10 1.00 0.90 0.80 0.74 0.66 0.59 0.54 0.50 0.46 0.42 0.38 0.34 0.31 0.28 0.26 0.23 0.22 0.19 MECHANICAL OUTLINES .059 [1,50] .260 [6,60] 1 XXX .188 [4,80] .181 [4,60] 2 .315 [8,00] .086 .248 [6,30] .118 Max. [2,20 [3,00] 1 NOTES: 1. Dimensions are shown in inches/millimeters 2. Unless otherwise specified, tolerance = Inches: ±0.012 2 = Millimeters: ±0,30 SCHEMATIC 3. IDC MAX based on the inductance being 75% of its initial value 4. Tape & reel quantity, 1500 pcs/reel 5. Terminal finish is compliant to RoHS requirements 6. Solder in accordance with J-STD-002 Rev. D 7. Non-RoHS series parts 42-340-6-XXX are finished with leaded solder Sn60Pb40 or equivalent DATATRONIC: 28151 Highway 74, Romoland, CA 92585 Tel: 951-928-7700 Fax: 951-928-7701 Email: [email protected] 499 King’s Road, Hong KongTel: (852) 2562 3858, (852) 2564 8477 Fax: (852) 2565 7214, (852) 2563 1290 All specifications are subject to change without notice.