CP800 THRU CP808 SINGLE-PHASE SILICON BRIDGE VOLTAGE - 50 to 800 Volts CURRENT - P.C. MTG 3A, HEAT-SINK MTG 8A Recongnized File #E111753 CP-8 FEATURES l Surge overload rating—200 Amperes peak l Low forward voltage drop and reverse leakage l Small size, simple installation l Plastic package has Underwriter Laboratory Flammability Classification 94V-O l Reliable low cost construction utilizing molded plastic technique MECHANICAL DATA Mounting position: Any Weight: 0.24 ounce, 6.9 grams Terminals: Leads solderable per MIL-STD-202, Method 208 Mounting torque: Thro hole for #6 screw MACXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS At 25 ¢J ambient temperature unless otherwise noted; resistive or inductive load at 60Hz . CP800 CP801 CP802 CP804 CP806 Max Recurrent Peak Reverse Voltage 50 100 200 400 600 Max Bridge Input Voltage RMS 35 70 140 280 420 ¢J 8.0 Max Average Rectified Output at TC=50 * 3.0 See Fig. 2 at TA=40 ¢J ** Peak One Cycle Surge Overload Current 200 Max Forward Voltage Drop per element at 1.1 4.0A DC & 25 ¢J . See Fig. 3 Max Rev Leakage at rated Dc Blocking Voltage per element at 25 ¢J 10.0 1.0 See Fig 4 at100 ¢J 2 I t Rating for fusing ( t<8.3ms) 166 Typical junction capacitance per leg (Note 4) CJ 200 Typical Thermal Resistance per leg (Note 3) R £KJA 21 Typical Thermal Resistance per leg (Note 2) R £KJL 6 Operating Temperature Range -55 TO +125 Storage Temperature Range -55 TO +150 CP808 800 560 NOTES: 1. Bolt down on heat-sink with silicon thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw. 2. Units Mounted on a 8.6”¡Ñ 8.6” ¡Ñ 24” thick (22 ¡Ñ 22 ¡Ñ 0.6cm) AL plate heatsink. 3. Units Mounted on P.C.B at 0.375”(9.5mm) lead length with 0.5 ¡Ñ 0.5”(12 ¡Ñ 12mm)copper pads. 4. Measured at 1.0MHZ and applied reverse voltage. UNITS V V A A A V £g A mA 2 A Sec PF ¢J /W ¢J ¢J RATING AND CHARACTERISTIC CURVES FORWARD SURGE CURRENT, AMPERES pk (HALF SINE WAVE) CP800 THRU CP808 OUTPUT CURRENT AMPERES 200 160 120 80 TA = 105 ¢J 40 0 1 2 6 10 20 40 60 100 10 (TC) METAL HEATSINK 8 6 4 (T A) P.C. BOARD 2 0 0 50 100 150 AMBIENT TEMPERATURE, ¢J NO. OF CYCLES AT 60Hz 5 4 3 2 1 .9 .8 .7 .5 TYPICAL DISTRIBUTION .3 .2 .1 .07 MEDIAN .05 .03 .02 .01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 INSTANTANEOUS FWD VOLTAGE, VOLTS Fig. 3-TYPICAL FORWARD CHARACTERISTICS(25 ¢J) INSTANTANEOUS REVERSE CURRENT, £g A INSTANTANEOUS FWD CURRENT, AMPERES Fig. 2-DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 100 10 25 ¢J 1 0 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE Fig. 4-REVERSE CHARACTERISTICS