6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 PACKAGE SCHEMATIC 1 NC 2 6 6 5 6 3 NC 4 1 PIN 1. ANODE 2. CATHODE 3. NO CONNECTION 4. EMITTER 5. COLLECTOR 6. NO CONNECTION 1 6 1 FEATURES The MOC810X and CNY17F-X devices consist of a gallium arsenide LED optically coupled to a silicon phototransistor in a dual-inline package. • • • • Closely Matched Current Transfer Ratio (CTR) Minimizes Unit-to-Unit Variation Narrow (CTR) Windows that Translate to a Narrow and Predictable Open Loop Gain Window Very Low Coupled Capacitance along with No Chip to Pin 6 Base Connection for Minimum Noise Susceptibility To order devices that are tested and marked per VDE 0884 requirements, the suffix “.300” must be included at the end of part number. e.g. MOC8101.300 VDE 0884 is a test option. APPLICATIONS • Switchmode Power Supplies (Feedback Control) • AC Line/Digital Logic Isolation • Interfacing and coupling systems of different potentials and impedances © 2004 Fairchild Semiconductor Corporation Page 1 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 ABSOLUTE MAXIMUM RATINGS (TA =25°C Unless otherwise specified) Parameter Symbol Value Unit IF 100 mA IF(pk) 1 A VR 6 Volts INPUT LED Forward Current - Continuous Forward Current - Peak (PW = 1µs, 300pps) Reverse Voltage LED Power Dissipation @ TA = 25°C PD Derate above 25°C 150 mW 2.0 mW/°C OUTPUT TRANSISTOR Collector-Emitter Voltage MOC8106/7/8, CNY17F-1/2/3/4 VCEO MOC8101/2/3/4/5 Emitter-Collector Voltage VECO Detector Power Dissipation @ TA = 25°C PD Derate above 25°C 70 30 Volts 7 Volts 150 mW 2.0 mW/°C 5300 Vac(rms) TOTAL DEVICE Input-Output Isolation Voltage VISO (f = 60 Hz, t = 1 min.) Total Device Power Dissipation @ TA = 25°C PD Derate above 25°C 250 mW 3.3 mW/°C Ambient Operating Temperature Range TOPR -55 to +100 °C Storage Temperature Range TSTG -55 to +150 °C TSOL 260 °C Lead Soldering Temperature (1/16” from case, 10 sec. duration) © 2004 Fairchild Semiconductor Corporation Page 2 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 ELECTRICAL CHARACTERISTICS (TA =25°C Unless otherwise specified)(1) Characteristic Symbol Min Typ** Max Unit VF — 1.40 1.65 V 1.0 1.18 1.5 INPUT LED Forward Voltage (IF = 60 mA) CNY17F-X (IF = 10 mA) MOC810X Reverse Leakage Current (VR = 5.0 V) IR — 0.001 10 µA Capacitance C — 18 — pF (VCE = 10 V, TA = 25°C) ICEO1 — 1.0 50 nA (VCE = 10 V, TA = 100°C) ICEO2 — 1.0 — µA 30 100 — 70 100 — V(BR) ECO 7.0 10 — V CCE — 8 — pF MOC8101 50 — 80 MOC8102 73 — 117 MOC8103 108 — 173 MOC8104 160 — 256 MOC8105 65 — 133 50 — 150 100 — 300 MOC8108 250 — 600 CNY17F-1 40 — 80 CNY17F-2 63 — 125 CNY17F-3 100 — 200 CNY17F-4 160 — 320 VCE(sat) — — 0.4 V OUTPUT TRANSISTOR Collector-Emitter Dark Current Collector-Emitter Breakdown Voltage MOC8101/2/3/4/5 (IC = 1.0 mA) MOC8106/7/8, CNY17F-1/2/3/4 (IC = 1.0 mA) Emitter-Collector Breakdown Voltage (IE = 100 µA) Collector-Emitter Capacitance V(BR) CEO (f = 1.0 MHz, VCE = 0) V COUPLED Output Collector Current (IF = 10 mA, VCE = 10 V) MOC8106 MOC8107 (IF = 10 mA, VCE = 5 V) (CTR)(2) % Collector-Emitter Saturation Voltage CNY17F-1/2/3/4 (IC = 2.5 mA, IF = 10 mA) MOC8101/2/3/4/5/6/7/8 (IC = 500 µA, IF = 5.0 mA) Isolation Voltage Isolation Resistance Isolation Capacitance (f = 60 Hz, t = 1.0 min.)(4) (VI-O = VISO 5300 — — Vac(rms) 500 V)(4) RISO 1011 — — Ω MHz)(4) CISO — 0.5 — pF (VI-O = 0, f = 1.0 ** All typicals at TA = 25°C © 2004 Fairchild Semiconductor Corporation Page 3 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 TRANSFER CHARACTERISTICS (TA =25°C Unless otherwise specified) AC Characteristic Test Conditions Symbol Min Typ** Max Unit µs NON-SATURATED SWITCHING TIME Turn-on Time CNY17F-1/2/3/4 Only (RL = 100 Ω, IC = 2 mA) ton — 2 10 Turn-off Time CNY17F-1/2/3/4 Only (VCC = 10 V) toff — 3 10 (IC = 2.0 mA, VCC = 10 V, RL = 100 Ω)(3) ton — 2 Turn-On Time MOC8101-5 MOC8106-8 Turn-Off Time MOC8101-5 MOC8106-8 (IC = 2.0 mA, VCC = 10 V, RL = 100 Ω)(3) Rise Time All Devices (IC = 2.0 mA, VCC = 10 V, RL = 100 Ω)(3) Fall Time All Devices (IC = 2.0 mA, VCC = 10 V, RL = 100 Ω)(3) 20 — 20 toff — 3 tr — 1 — tf — 2 — — — 5.5 µs — µs SATURATED SWITCHING TIMES Turn-on Time CNY17F-1 CNY17F-2 CNY17F-3 CNY17F-4 Rise Time CNY17F-1 CNY17F-2 CNY17F-3 CNY17F-4 Turn-off Time CNY17F-1 CNY17F-2 CNY17F-3 CNY17F-4 Fall Time CNY17F-1 CNY17F-2 CNY17F-3 CNY17F-4 ** All typicals at TA = 25°C (IF = 20 mA, VCE = 0.4 V) ton µs (IF = 10 mA, VCE = 0.4 V) — — 8.0 (IF = 20 mA, VCE = 0.4 V) — — 4.0 tr µs (IF = 20 mA, VCE = 0.4 V) (IF = 20 mA, VCE = 0.4 V) — — 34 toff µs (IF = 10 mA, VCE = 0.4 V) — — 39 (IF = 20 mA, VCE = 0.4 V) — — 20 tf (IF = 10 mA, VCE = 0.4 V) µs — — 24 NOTES: 1. Always design to the specified minimum/maximum electrical limits (where applicable). 2. Current Transfer Ratio (CTR) = IC/IF x 100%. 3. For test circuit setup and waveforms, refer to Figure 11. 4, For this test, Pins 1 and 2 are common, and Pins 4 are 5 are common. © 2004 Fairchild Semiconductor Corporation Page 4 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 TYPICAL PERFORMANCE CURVES Fig. 1 LED Forward Voltage vs. Forward Current Fig. 2 Normalized CTR vs. Forward Current 1.8 1.4 TA = 25°C VCE = 5.0 V Normalized to IF = 10 mA 1.2 1.6 1.0 NORMALIZED CTR VF - FORWARD VOLTAGE (V) 1.7 1.5 TA = -55°C 1.4 1.3 1.2 0.8 0.6 0.4 TA = 25°C 0.2 1.1 TA = 100°C 1.0 0.0 1 10 100 0 IF - LED FORWARD CURRENT (mA) 5 10 15 20 IF - FORWARD CURRENT (mA) Fig. 3 Normalized CTR vs. Ambient Temperature Fig. 4 CTR vs. RBE (Saturated) 1.6 1.0 0.9 IF = 5 mA 0.8 NORMALIZED CTR NORMALIZED CTR 1.4 1.2 IF = 10 mA 1.0 IF = 20 mA 0.7 0.6 IF = 10 mA 0.5 0.4 0.8 0.3 IF = 20 mA 0.6 0.4 -75 IF = 5 mA 0.2 Normalized to IF = 10 mA TA = 25°C TA = 25°C VCE = 0.3 V Normalized to CTR @ RBE = Open 0.1 0.0 -50 -25 0 25 50 75 100 125 10 TA - AMBIENT TEMPERATURE (°C) © 2004 Fairchild Semiconductor Corporation 100 1000 RBE - BASE RESISTANCE (kΩ) Page 5 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 TYPICAL PERFORMANCE CURVES (continued) Fig. 6 Collector Emitter Saturation Voltage vs Collector Current VCE (sat) - COLLECTOR-EMITTER SATURATION VOLTAGE (V) Fig. 5 CTR vs. RBE (Unsaturated) 1.0 0.9 NORMALIZED CTR 0.8 IF = 20 mA 0.7 0.6 IF = 10 mA 0.5 0.4 IF = 5 mA 0.3 0.2 TA = 25°C VCE = 5.0 V Normalized to CTR @ RBE = Open 0.1 0.0 10 100 1000 RBE - BASE RESISTANCE (kΩ) 100 10 1 IF = 2.5 mA 0.1 IF = 5 mA IF = 10 mA TA = 25°C 0.001 0.01 0.1 1 10 IC - COLLECTOR CURRENT (mA) Fig. 7 Normalized ton vs. RBE Fig. 8 Normalized toff vs. RBE 6.0 1.4 5.5 1.3 5.0 1.2 VCC = 10 V IC = 2 mA RL = 100 Ω Normalized to toff@ RBE = Open 1.1 4.5 1.0 4.0 NORMALIZED toff NORMALIZED ton IF = 20 mA 0.01 3.5 3.0 2.5 2.0 1.5 0.9 0.8 0.7 0.6 0.5 0.4 VCC = 10 V IC = 2 mA RL = 100 Ω Normalized to ton@ RBE = Open 1.0 0.5 0.3 0.2 0.1 0.0 10 100 1000 10 10000 1000 10000 RBE - BASE RESISTANCE (kΩ) RBE - BASE RESISTANCE (kΩ) © 2004 Fairchild Semiconductor Corporation 100 Page 6 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 TYPICAL PERFORMANCE CURVES (continued) Fig. 9 Switching Speed vs. Load Resistor Fig. 10 Dark current vs. Ambient Temperature. 1000 ICEO - COLLECTOR-EMITTER DARK CURRENT (µA) 1e+1 SWITCHING SPEED - (µs) IF = 10 mA VCC = 10 V TA = 25°C 100 Toff Tf 10 Ton 1 Tr 0.1 VCE = 10V 1e+0 1e-1 1e-2 1e-3 1e-4 1e-5 1e-6 0.1 1 10 100 0 R-LOAD RESISTOR (kΩ) © 2004 Fairchild Semiconductor Corporation 25 50 75 100 125 TA - AMBIENT TEMPERATURE (°C) Page 7 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 Figure 11. Switching Time Test Circuit and Waveforms TEST CIRCUIT WAVE FORMS VCC = 10V INPUT PULSE IF IC INPUT RL = 100Ω 10% OUTPUT OUTPUT PULSE 90% tr ton tf toff Adjust IF to produce IC = 2 mA © 2004 Fairchild Semiconductor Corporation Page 8 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 Package Dimensions (Through Hole) MOC8104 MOC8108 CNY17F-4 Package Dimensions (Surface Mount) 0.350 (8.89) 0.330 (8.38) PIN 1 ID. 3 2 PIN 1 ID. 1 0.270 (6.86) 0.240 (6.10) SEATING PLANE 0.270 (6.86) 0.240 (6.10) 0.350 (8.89) 0.330 (8.38) 4 0.070 (1.78) 0.045 (1.14) 5 6 0.300 (7.62) TYP 0.070 (1.78) 0.045 (1.14) 0.200 (5.08) 0.135 (3.43) 0.200 (5.08) 0.165 (4.18) 0.020 (0.51) MIN 0.154 (3.90) 0.100 (2.54) 0.016 (0.41) 0.008 (0.20) 0.020 (0.51) MIN 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.016 (0.40) 0.008 (0.20) 0.022 (0.56) 0.016 (0.41) 0° to 15° 0.016 (0.40) MIN 0.315 (8.00) MIN 0.405 (10.30) MAX 0.300 (7.62) TYP Lead Coplanarity : 0.004 (0.10) MAX 0.100 (2.54) TYP Package Dimensions (0.4” Lead Spacing) Recommended Pad Layout for Surface Mount Leadform 0.070 (1.78) 0.270 (6.86) 0.240 (6.10) 0.060 (1.52) SEATING PLANE 0.350 (8.89) 0.330 (8.38) 0.415 (10.54) 0.070 (1.78) 0.045 (1.14) 0.100 (2.54) 0.295 (7.49) 0.030 (0.76) 0.200 (5.08) 0.135 (3.43) 0.154 (3.90) 0.100 (2.54) 0.004 (0.10) MIN 0.016 (0.40) 0.008 (0.20) 0° to 15° 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.400 (10.16) TYP NOTE All dimensions are in inches (millimeters) © 2004 Fairchild Semiconductor Corporation Page 9 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 ORDERING INFORMATION Option Order Entry Identifier Description .S Surface Mount Lead Bend SD .SD Surface Mount; Tape and Reel W .W 0.4" Lead Spacing .300 VDE 0884 .300W VDE 0884, 0.4" Lead Spacing S 300 300W 3S 3SD .3S VDE 0884, Surface Mount .3SD VDE 0884, Surface Mount, Tape and Reel MARKING INFORMATION 1 MOC8101 2 V XX YY K 6 3 4 5 Definitions 1 Fairchild logo 2 Device number 3 VDE mark (Note: Only appears on parts ordered with VDE option – See order entry table) 4 Two digit year code, e.g., ‘03’ 5 Two digit work week ranging from ‘01’ to ‘53’ 6 Assembly package code © 2004 Fairchild Semiconductor Corporation Page 10 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 Carrier Tape Specifications (“D” Taping Orientation) 12.0 ± 0.1 4.85 ± 0.20 4.0 ± 0.1 Ø1.55 ± 0.05 4.0 ± 0.1 0.30 ± 0.05 1.75 ± 0.10 7.5 ± 0.1 13.2 ± 0.2 9.55 ± 0.20 Ø1.6 ± 0.1 10.30 ± 0.20 0.1 MAX 16.0 ± 0.3 User Direction of Feed NOTE All dimensions are in inches (millimeters) Reflow Profile (Black Package, No Suffix) Temperature (°C) 300 215°C, 10–30 s 250 225 C peak 200 150 Time above 183°C, 60–150 sec 100 50 Ramp up = 3C/sec • Peak reflow temperature: 225°C (package surface temperature) • Time of temperature higher than 183°C for 60–150 seconds • One time soldering reflow is recommended 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 Time (Minute) © 2004 Fairchild Semiconductor Corporation Page 11 of 12 1/21/04 6-PIN DIP OPTOCOUPLERS FOR POWER SUPPLY APPLICATIONS (NO BASE CONNECTION) MOC8101 MOC8105 CNY17F-1 MOC8102 MOC8106 CNY17F-2 MOC8103 MOC8107 CNY17F-3 MOC8104 MOC8108 CNY17F-4 DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. © 2004 Fairchild Semiconductor Corporation 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Page 12 of 12 1/21/04