Murata CDALA10M7CA040 Ceramic filters (cerafil) for fm receiver Datasheet

Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
CERAMIC
FILTERS
(CERAFILr)
Murata
Manufacturing Co., Ltd.
Cat.No.P61E-7
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
CONTENTS
1
CERAFILr and "CERAFIL" in this catalog are
the trademarks of Murata Manufacturing Co., Ltd.
Part Numbering
1
2
P61E7.pdf 01.10.17
2
CERAFILr Chip Type SFECV Series
3
Chip CERAFILr SFECV Series Notice
6
CERAFILr Small Chip Type SFECS Series
7
Chip CERAFILr SFECS Series Notice
10
3
CERAFILr Standard Lead Type
11
4
CERAFILr Low-loss Type
14
5
CERAFILr Low-profile Type
17
6
CERAFILr Lower Spurious Response Type
20
7
CERAFILr Wider Band-width Type
23
8
CERAFILr Narrow Band Type
25
9
CERAFILr For FM -IF Tuners
28
10
CERAFILr Three-Elements Type SFTLA Series
33
Lead Type CERAFILr Test Circuit and Characteristics Data
36
Lead Type CERAFILr Characteristics Data and Notice
37
11
12
13
Discriminators Chip Type CDACV Series
38
Chip Type Discriminators CDACV Series Notice
41
Discriminators Chip Low-profile Type CDSCA Series
42
Chip Type Discriminators CDSCA Series Notice
44
Discriminators CDALA Series
45
Lead Type Discriminators Notice
49
Packaging
50
Test Circuit of Ceramic Discriminator
53
Example of Appllied Circuit
54
Recycled Paper
2
3
4
5
6
7
8
9
10
11
12
13
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
o Part Numbering
P61E7.pdf 01.10.17
structure of the "Global Part Numbers" that have been adopted since June 2001 and the meaning of each code are described herein.
( The
)
If you have any questions about details, inquire at your usual Murata sales office or distributor.
CERAFILr for FM
(Global Part Number)
SF
E
LA
q
w
e
10M7 FAA0
r
t
-R0
y
qProduct ID
tProduct Specification
Product ID
Product Specification
Code
SF
Ceramic Filters
FAA0
wOscillation/Numbers of Element
Four-digit alphanumerics express
pass-bandwidth, center frequency tolerance,
rank, series, others.
Code
Oscillation/Numbers of Element
E
2 Elements Thickness Expander mode
T
3 Elements Thickness Expander mode
Code
K
2 Elements Thickness Expander mode
(2nd Harmonic)
-B0
Bulk
-R0
Plastic Taping ø180mm
V
2 Elements Thickness Expander mode
(3rd Over Tone)
-R1
Plastic Taping ø330mm
-A0
1500pcs. /Radial Taping H0=18mm
-A1
1000pcs. /Radial Taping H0=18mm
eStructure/Size
Code
Structure/Size
Lp
Lead Type
Cp
Chip Type
yPackaging
Packaging
Radial taping is applied to lead type and plastic taping to chip type.
With non-standard products, two-digit alphanumerics indicating
"Individual Specification" is added between "tProduct Specification"
and "yPackaging".
p is expressed "A" or subsequent code, which indicates the size.
rNominal Center Frequency
Expressed by four-digit alphanumerics. The unit is in hertz (MHz).
Decimal point is expressed by capital letter "M".
Discriminators for FM
(Global Part Number)
CD
A
LA
10M7
GA
001 -R0
q
w
e
r
t
y
u
qProduct ID
tProduct Specification
Product ID
CD
Discriminators
Code
Product Specification
GA
Two-digit alphanumerics express
type, center frequency, rank, others
wOscillation
Code
Oscillation
A
Thickness Expander mode
yIC
Code
IC
001
Applicable IC Control Code
eStructure/Size
Structure/Size
Lp
Lead Type
Code
Cp
Chip Type
-B0
Bulk
-A0
Radial Taping H0=18mm
-R0
Plastic Taping (ø180mm)
-R1
Plastic Taping (ø330mm)
p is expressed "A" or subsequent code, which indicates the size.
rNominal Center Frequency
Expressed by four-digit alphanumerics . The unit is in hertz (MHz).
Decimal point is expressed by capital letter "M".
2
uPackaging
Code
Packaging
Radial taping is applied to lead type and plastic taping to chip type.
With non-standard products, an alphanumerics indicating "Individual
Specification" is added between "yIC" and "uPackaging".
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
1
CERAFILr Chip Type SFECV Series
6.9±0.3
4.05±0.4
SFECV10M7 series for FM-receivers are monolithic type
ceramic filters which utilize the energy trapped
thickness vibration-mode of the piezoelectric ceramic.
By taking advantage of the very low profile, new SFECV
series and PFWCC(kHz filter for AM receiver) enable
costomers to make AM/FM set so thin, and it can be of
help to the total chip circuit.
2.9±0.3
1.2±0.5
1.2±0.3
(2)
(1)
Bottom Electrode
Side Electrode
1.5±0.2
■ Features
: Marking
1.0±0.5
1. Super-thin. Only 1.5mm. The most suitable ceramic
filter available for thinning substrates.
2. Heat resistant. Reflow soldering can be performed
because of its excellent heat resistance.
3. Piezoelectric element is connected in the
sandwich shape by heat resistant substrate, thus
it has excellent mechanical strength, and it is
suitable for automatic mounting.
4. Various bandwidths are available. Select a
suitable type in accordance with the desired
selectivity.
5. Electrical characteristics are the same as
conventional "CERAFIL".
1.5±0.2
*
*
*
(3)
1.2±0.5
1.0±0.5
1.0±0.5
** : EIAJ Monthly Code
** : Center Frequency Rank Code
(1) : Input
(2) : Ground
(3) : Output
(in mm)
■ Applications
1. Small, thin radios
2. Automotive radios
3. Headphone steros
Center Frequency (fo)
(MHz)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Insertion Loss
(dB)
Spurious Attenuation
(dB)
SFECV10M7KA00-R0
10.700 ±30kHz
within110 ±30kHz
320 max.
within6.0 ±2.0dB
35 min.
SFECV10M7JA00-R0
10.700 ±30kHz
within150 ±40kHz
380 max.
10.0 max.
30 min.
SFECV10M7HA00-R0
10.700 ±30kHz
within180 ±40kHz
470 max.
within4.0 ±2.0 dB
35 min.
SFECV10M7GA00-R0
10.700 ±30kHz
within230 ±50kHz
510 max.
within3.5 ±2.0 dB
35 min.
SFECV10M7FA00-R0
10.700 ±30kHz
within280 ±50kHz
590 max.
within3.0 ±2.0 dB
35 min.
Part Number
Area of Attenuation : [within 20dB]
Area of Spurious Attenuation : [within 9MHz to 12MHz]
Center frequency(fo) defined by the center of 3dB bandwidth.
■ Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
3
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
■ Frequency Characteristics
SFECV10M7JA00-R0
0
0
10
10
20
20
Attenuation (dB)
30
40
30
40
50
50
60
60
70
9.700
10.200
10.700
Frequency (MHz)
11.200
70
9.700
11.700
1
5.50
2
5.00
3
4.50
4
4.00
5
3.50
6
3.00
10.600
10.700
Frequency (MHz)
10.800
11.200
11.700
0
5.50
1
5.00
2
4.50
3
4.00
4
3.50
5
3.00
6
2.50
7
2.50
7
Attenuation (dB)
6.00
10.500
10.700
Frequency (MHz)
SFECV10M7GA00-R0
0
G.D.T. (µsec.)
Attenuation (dB)
SFECV10M7HA00-R0
10.200
10.500
10.600
10.900
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
Attenuation (dB)
SFECV10M7KA00-R0
2.00
5.00
1
4.50
2
4.00
3
3.50
4
3.00
5
2.50
6
2.00
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
Attenuation (dB)
SFECV10M7FA00-R0
0
1.50
■ Frequency Characteristics (Spurious)
SFECV10M7KA00-R0
SFECV10M7JA00-R0
0
0
10
10
20
20
Attenuation (dB)
Attenuation (dB)
1
P61E7.pdf 01.10.17
30
40
30
40
50
50
60
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
Continued on the following page.
4
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Continued from the preceding page.
■ Frequency Characteristics (Spurious)
10
10
20
20
30
40
30
40
50
50
60
60
70
8.700
9.700
10.700
Frequency (MHz)
1
SFECV10M7GA00-R0
0
Attenuation (dB)
Attenuation (dB)
SFECV10M7HA00-R0
0
11.700
12.700
11.700
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
SFECV10M7FA00-R0
0
10
Attenuation (dB)
20
30
40
50
60
70
8.700
9.700
10.700
Frequency (MHz)
■ Standard Land Pattern Dimensions
1.2
1.2
■ Test Circuit
1.2
(1): Input
(2): Ground
(3): Output
R1
(2)
Rg
4.0
(3)
(1)
E1
R2
C2
E2
S.S.G.
=-10dBm
1.65
1.65
2.85
2.85
Land
(in mm)
RF
Voltmeter
Rg = 50Ω R1 = 280Ω ±5% R2 = 330Ω ±5%
C2 = 10 ± 2 pF (Including stray capacitance and Input capacitance
of RF Volt Meter)
E1 : S.S.G. S.S.G. Output Voltage
5
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Chip CERAFILr SFECV Series Notice
1
■ Notice (Soldering and Mounting)
1. Standard Reflow Soldering Condition
(1) Reflow
5sec.
240
Temperaturu(°C)
230
Gradual Cooling
150
60
30
Time(sec.)
(2) Soldering Iron
Lead terminal is directly contacted with the tip of
soldering iron of 280±5˚C for 3.0±0.5 seconds.
2. Wash
The component cannot be withstand washing.
■ Notice (Handling)
1. The component will be damaged when an excessive
stress is applied.
2. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
3. Design layout of components on the PC board to
minimize the stress imposed on the warp or flexure of the
board.
4. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause
destruction resistance characteristics to lower. To
prevent this, be extremely careful in determining shape
and dimension before designing the circuit board
diagram.
5. When the positioning claws and pick up nozzle are worn,
the load is applied to the chip while positioning is
concentrated to one positioning accuracy, etc. Careful
checking and maintenance are necessary to prevent
unexpected trouble.
6. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component. Depending on the soldering conditions, the
effective area of terminations may be reduced. the use of
solder containing Ag should be done to prevent the
electrode erosion.
7. Do not clean or wash the component as it is not
hermetically sealed.
8. In case of covering filter with over coat, conditions such
as material of resin, cure temperature, and so on should
be evaluated well.
9. Do not use strong acidity flux, more than 0.2wt% chlorine
content, in re-flow soldering.
10. Accurate test circuit values are required to measure
electrical characteristics.It may be a cause of miscorrelation if there is any deviation, especially stray
capacitance, from the test circuit in the specification.
6
[Component direction]
Put the
component
lateral to the
direction in
which stress
acts.
[Component layout close to board]
Perforation
A
B
Slit
C
Susceptibility to
stress is in the order
of : A>C>B
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
CERAFILr Small Chip Type SFECS Series
2
0.85T0.3
FA
Input electrode marker
0-0.3 0.6T0.3
0.4 W0.3
Y0.2
0.6T0.3 0-0.3
(1.35) (1.35)
0.7T0.3 0.7T0.3 0.7T0.3
0.85T0.3
1.4T0.1
3.10T0.2
3.45T0.2
SFECS10M7 series for FM-receivers are small, high
performance and super thin (1.4mm) filters.
Piezoelectric element is connected in the sandwich
shape by ceramics substrate.
They have 1.4mm thickness and small mounting area.
(3.5x3.1mm)
New SFECS series and PFWCC(kHz filter for AM receiver)
enable customers to make AM/FM set so thin and small
sized.
(1) (2)
(3)
(4)
(1.30)
0-0.3
(1.30)
0-0.3
(1) : Input
(2) : Ground
(3) : Float (Signal line)
(4) : Output
(*) : Reference
: EIAJ Monthly Code
(in mm)
■ Features
1. The filters are mountable by automatic placers.
2. They are slim, at only 1.4mm thickness, and have
a small mounting area (3.5x3.1mm) enabling
flexible PCB design.
3. Various bandwidths are available. Select a
suitable type in accordance with the desires
selectivity.
4. Operating temperature range :
-20 to +80 (degree C)
Storage temperature range :
-40 to +85 (degree C)
■ Applications
1. Small, thin radios
2. Headphone stereos
Center Frequency (fo)
(MHz)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Insertion Loss
(dB)
Spurious Attenuation
(dB)
SFECS10M7HA00-R0
10.700 ±30kHz
within180 ±40kHz
470 max.
within4.5 ±2.0 dB
30 min.
SFECS10M7GA00-R0
10.700 ±30kHz
within230 ±50kHz
510 max.
within3.5 ±2.0 dB
30 min.
SFECS10M7FA00-R0
10.700 ±30kHz
within280 ±50kHz
590 max.
within3.0 ±2.0 dB
30 min.
Part Number
Area of Attenuation : [within 20dB]
Area of Spurious Attenuation : [within 9MHz to 12MHz]
Center frequency(fo) defined by the center of 3dB bandwidth.
■ Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
7
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Frequency Characteristics
SFECS10M7HA00-R0
SFECS10M7GA00-R0
0
5.60
5.00
4.80
5.40
2
5.20
2
2
4.60
4.60
4.40
6
4.40
Attenuation (dB)
4.80
4
G.D.T. (µsec.)
Attenuation (dB)
5.00
4
4.20
4.00
6
3.80
4.20
3.60
4.00
8
8
3.40
3.80
10
10.500
10.600
10.700
10.800
10.900
3.20
3.60
10
10.500
10.600
Frequency (MHz)
10.700
10.800
10.900
3.00
Frequency (MHz)
SFECS10M7FA00-R0
0
4.60
4.40
2
4.20
3.80
3.60
6
3.40
G.D.T. (µsec.)
Attenuation (dB)
4.00
4
3.20
8
3.00
2.80
10
10.500
10.600
10.700
10.800
10.900
2.60
Frequency (MHz)
■ Frequency Characteristics (Spurious)
SFECS10M7GA00-R0
0
0
10
10
Attenuation (dB)
Attenuation (dB)
SFECS10M7HA00-R0
20
30
40
50
8.700
9.700
10.700
11.700
12.700
0
Attenuation (dB)
10
20
30
40
9.700
10.700
Frequency (MHz)
50
8.700
9.700
10.700
Frequency (MHz)
SFECS10M7FA00-R0
8
30
40
Frequency (MHz)
50
8.700
20
11.700
12.700
11.700
12.700
G.D.T. (µsec.)
0
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
■ Test Circuit
0.1
■ Standard Land Pattern Dimensions
(3)
0.3
R1
1.05
0.1
(4)
(2)
0.1
E1
0.1
R2
C2
E2
RF
Voltmeter
S.S.G.
=-10dBm
1.05
(3)
0.1
0.3
(2)
2
(4)
Rg
1.40
0.3
(1)
(1)
P61E7.pdf 01.10.17
0.1
0.8
0.6
0.8
0.6
0.8
(1) : Input (2) : Ground (3) : Float Signal Line (4) : Out put
It shows solder resist land pattern.
(in mm)
Rg=50Ω
R1=280Ω
R2=330Ω
C2=10pF
(Including stray capacitance
and Input capacitance of RF Voltmeter)
(1) : Input
(2) : Ground
(3) : Float
(4) : Output
9
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Chip CERAFILr SFECS Series Notice
■ Notice (Soldering and Mounting)
1. Standard Reflow Soldering Condition
(1) Reflow
Temperature (˚C)
2
Peak
(240˚C max.)
240
200
Pre-heating
(120-170˚C)
100
Heating
(200˚C)
Gradual
Cooling
(2) Soldering Iron
Filter shall be soldered at 280±5˚C for 3.0±0.5 seconds.
The soldering iron shall not touch the filter white soldering.
30 sec.
min.
60-120 sec.
30 sec.
max.
120 sec.
min.
2. Wash
The component cannot be withstand washing.
■ Notice (Handling)
1. The component will be damaged when an excessive
stress is applied.
2. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
3. Design layout of components on the PC board to
minimize the stress imposed on the warp or flexure of the
board.
4. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause destruction
resistance characteristics to lower. To prevent this, be
extremly careful in determining shape and dimension
before designing the circuit board diagram.
5. When the positioning claws and pick up nozzle are worn,
the load is applied to the chip while positioning is
concentrated to one positioning accuracy, etc. Careful
checking and maintenance are necessary to prevent
unexpected trouble.
6. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component. Depending on the soldering conditions, the
effective area of terminations may be reduced. The use
of solder containing Ag should be done to prevent the
electrode erosion.
7. Do not clean or wash the component as it is not
hermetically sealed.
8. In case of covering filter with over coat, conditions such
as material of resin, cure temperature, and so on should
be evaluated well.
9. Do not use strong acidity flux, more than 0.2wt% chlorine
content, in re-flow soldering.
10. Accurate test circuit values are required to measure
electrical characteristics.
It may be a cause of mis-correlation if there is any
deviation, especially stray capacitance, from the test
circuit in the specification.
10
[Component layout close to board]
Perforation B
A
Slit
C
Susceptibility to
stress is in the order
of : A>C>B
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
CERAFILr Standard Lead Type
7.0±2.0
SFELA10M7 series for FM-receivers are monolithic type
ceramic filters which use the energy trapped thickness
vibration-mode of the piezoelectric ceramic.
MARKING
■ Features
3
7.0±2.0
EIAJ
CODE
0.5±0.1
2.5±0.2 2.5±0.2
3.0±1.0
SFELA10M7HA00-B0
0.3±0.1
(3)
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(1)
(2)
7.0±2.0
MARKING
EIAJ
CODE
7.0±2.0
1. These miniature filters have high mechanical
strength.
2. Low loss, favorable waveform symmetry, and high
selectivity.
3. Various band widths are available for applications
in wide to narrow bands.
4. Small dispersion and stable characteristics.
5. Change in center frequency is typically within
±30ppm/(degree C) at -20 to +80 (degree C).
6. High reliability.
5.0±1.0
1.38±0.2
1.7±0.1
5.0±1.0
1.38±0.2
1.7±0.1
0.5±0.1
3.0±1.0
SFELA10M7GA00-B0
0.3±0.1
2.5±0.2 2.5±0.2
(3)
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(1)
(2)
7.0±2.0
EIAJ
CODE
7.0±2.0
MARKING
5.0±1.0
1.38±0.2
1.7±0.1
0.5±0.1
3.0±1.0
SFELA10M7FA00-B0
0.3±0.1
2.5±0.2 2.5±0.2
(3)
Center Frequency (fo)
(MHz)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
SFELA10M7HA00-B0
10.700 ±30kHz
within180 ±40kHz
SFELA10M7GA00-B0
10.700 ±30kHz
within230 ±50kHz
SFELA10M7FA00-B0
10.700 ±30kHz
within280 ±50kHz
Part Number
(2)
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(1)
Insertion Loss
(dB)
Spurious Attenuation
(dB)
520 max.
7.0 max.
40 min.
570 max.
within4.0 ±2.0dB
40 min.
650 max.
within4.0 ±2.0dB
30 min.
Area of Attenuation : [within 20dB]
Area of Spurious Attenuation : [within 9MHz to 12MHz]
Center frequency(fo) defined by the center of 3dB bandwidth.
11
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Center Frequency Rank Code
3
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
■ Frequency Characteristics
5.50
1
5.50
1
5.00
2
5.00
2
4.50
3
4.50
3
4.00
4
4.00
4
3.50
5
3.50
5
3.00
6
3.00
6
2.50
2.50
7
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
Attenuation (dB)
0
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
SFELA10M7GA00-B0
6.00
G.D.T. (µsec.)
Attenuation (dB)
SFELA10M7HA00-B0
0
2.00
5.00
1
4.50
2
4.00
3
3.50
4
3.00
5
2.50
6
2.00
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
Attenuation (dB)
SFELA10M7FA00-B0
0
1.50
■ Frequency Characteristics (Spurious)
SFELA10M7GA00-B0
0
10
10
20
20
Attenuation (dB)
Attenuation (dB)
SFELA10M7HA00-B0
0
30
40
30
40
50
50
60
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
Continued on the following page.
12
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Continued from the preceding page.
■ Frequency Characteristics (Spurious)
SFELA10M7FA00-B0
0
10
Attenuation (dB)
20
30
40
3
50
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
■ Spurious Response
SFELA10M7FA00-B0
0
10
Attenuation (dB)
20
30
40
50
60
70
0
20
40
60
80
100
Frequency (MHz)
13
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
CERAFILr Low-loss Type
7.0±2.0
SFELA10M7 series for FM-receivers are monolithic type
ceramic filters which use the energy trapped thickness
vibration-mode of the piezoelectric ceramic.
EIAJ
CODE
■ Features
1. Insertion loss is 1 to 1.5dB lower than
conventional products. This types are useful for
elevating the sensitivity of sets.
2. Small dispersion and stable characteristics.
3. Excellent shape factor of frequency response.
4. Good waveform symmetry.
5.0±1.0
1.38±0.2
1.7±0.1
0.5±0.1
3.0±1.0
SFELA_JAA0-B0
0.3±0.1
2.5±0.2 2.5±0.2
(3)
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(1)
(2)
7.0±2.0
EIAJ
CODE
7.0±2.0
MARKING
5.0±1.0
1.38±0.2
1.7±0.1
0.5±0.1
3.0±1.0
(3)
MARKING
MARKING
7.0±2.0
7.0±2.0
EIAJ
CODE
0.5±0.1
5.0±1.0
1.38±0.2
1.7±0.1
5.0±1.0
1.38±0.2
1.7±0.1
0.5±0.1
(3)
(2)
SFELA_FAA0-B0
3.0±1.0
3.0±1.0
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
0.3±0.1
2.5±0.2 2.5±0.2
SFELA_GAA0-B0
(in mm)
(1)
(2)
7.0±2.0
EIAJ
CODE
(1) : Input
(2) : Ground
(3) : Output
7.0±2.0
SFELA_HAA0-B0
0.3±0.1
2.5±0.2 2.5±0.2
0.3±0.1
4
7.0±2.0
MARKING
(in mm)
(1)
(3)
(2)
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(1)
Center Frequency (fo)
(MHz)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Insertion Loss
(dB)
Spurious Attenuation
(dB)
SFELA10M7JAA0-B0
10.700 ±30kHz
within150 ±40kHz
360 max.
within4.5 ±2.0dB
35 min.
SFELA10M7HAA0-B0
10.700 ±30kHz
within180 ±40kHz
470 max.
within3.5 ±1.5dB
35 min.
SFELA10M7GAA0-B0
10.700 ±30kHz
within230 ±50kHz
520 max.
within3.0 ±2.0dB
35 min.
SFELA10M7FAA0-B0
10.700 ±30kHz
within280 ±50kHz
590 max.
within2.5 ±2.0dB
30 min.
Part Number
Area of Attenuation : [within 20dB]
Area of Spurious Attenuation : [within 9MHz to 12MHz]
Center frequency(fo) defined by the center of 3dB bandwidth.
14
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
■ Frequency Characteristics
1
7.00
1
6.00
2
6.50
2
5.50
3
6.00
3
5.00
4
5.50
4
4.50
5
5.00
5
4.00
6
4.50
6
3.50
4.00
7
10.600
10.700
Frequency (MHz)
10.800
10.900
10.500
SFELA10M7GAA0-B0
10.600
10.700
Frequency (MHz)
10.800
10.900
3.00
SFELA10M7FAA0-B0
0
5.50
1
6.00
1
5.00
2
5.50
2
4.50
3
5.00
3
4.00
4
4.50
4
3.50
5
4.00
5
3.00
6
3.50
6
2.50
3.00
7
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
Attenuation (dB)
6.50
G.D.T. (µsec.)
0
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
10.500
Attenuation (dB)
7.50
G.D.T. (µsec.)
6.50
0
7
Attenuation (dB)
4
SFELA10M7HAA0-B0
0
G.D.T. (µsec.)
Attenuation (dB)
SFELA10M7JAA0-B0
2.00
■ Frequency Characteristics (Spurious)
SFELA10M7HAA0-B0
0
10
10
20
20
Attenuation (dB)
Attenuation (dB)
SFELA10M7JAA0-B0
0
30
40
30
40
50
50
60
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
Continued on the following page.
15
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Continued from the preceding page.
■ Frequency Characteristics (Spurious)
10
10
20
20
30
40
16
30
40
50
50
60
60
70
8.700
4
SFELA10M7FAA0-B0
0
Attenuation (dB)
Attenuation (dB)
SFELA10M7GAA0-B0
0
9.700
10.700
Frequency (MHz)
11.700
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
CERAFILr Low-profile Type
SFELB10M7 series for FM-receivers are monolithic type
ceramic filters which use the energy trapped thickness
vibration-mode of the piezoelectric ceramic.
5.0±1.0
1.5±0.1
1.3±0.1
■ Features
0.5±0.1
1. Installed height is 5 mm, making it well suited for
compact, thin sets.
2. Environmental reliability is the same as those of
the ceramic filter SFELA10M7 series.
3.0±1.0
SFELB10M7KA00-B0
0.3±0.1
2.5±0.2 2.5±0.2
(1)
EIAJ
CODE
EIAJ
CODE
MARKING
0.5±0.1
5.0±1.0
1.5±0.1
1.3±0.1
5.0±1.0
1.5±0.1
1.3±0.1
0.5±0.1
(2)
3.0±1.0
SFELB10M7HA00-B0
in mm
(3)
(1)
MARKING
in mm
(3)
7.5±2.0
EIAJ
CODE
6.0 max.
7.5±2.0
(2)
(1) : Input
(2) : Ground
(3) : Output
MARKING
0.5±0.1
5.0±1.0
1.5±0.1
1.3±0.1
5.0±1.0
1.5±0.1
1.3±0.1
EIAJ
CODE
6.0 max.
(1)
(1) : Input
(2) : Ground
(3) : Output
0.3±0.1
2.5±0.2 2.5±0.2
3.0±1.0
0.3±0.1
2.5±0.2 2.5±0.2
0.5±0.1
(1)
(2)
SFELB10M7FA00-B0
3.0±1.0
(1) : Input
(2) : Ground
(3) : Output
0.3±0.1
2.5±0.2 2.5±0.2
3.0±1.0
0.3±0.1
2.5±0.2 2.5±0.2
SFELB10M7GA00-B0
in mm
(3)
6.0 max.
MARKING
(2)
(1) : Input
(2) : Ground
(3) : Output
7.5±2.0
6.0 max.
7.5±2.0
SFELB10M7JA00-B0
EIAJ
CODE
MARKING
6.0 max.
7.5±2.0
in mm
(3)
(1)
(2)
(1) : Input
(2) : Ground
(3) : Output
in mm
(3)
Center Frequency (fo)
(MHz)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Insertion Loss
(dB)
Spurious Attenuation
(dB)
SFELB10M7KA00-B0
10.700 ±30kHz
within110 ±30kHz
350 max.
within7.0 ±2.0dB
30 min.
SFELB10M7JA00-B0
10.700 ±30kHz
within150 ±40kHz
360 max.
within4.5 ±2.0dB
35 min.
SFELB10M7HA00-B0
10.700 ±30kHz
within180 ±40kHz
470 max.
within3.5 ±2.0dB
35 min.
SFELB10M7GA00-B0
10.700 ±30kHz
within230 ±50kHz
570 max.
within3.0 ±2.0dB
40 min.
SFELB10M7FA00-B0
10.700 ±30kHz
within280 ±50kHz
650 max.
within3.0 ±2.0dB
30 min.
Part Number
Area of Attenuation : [within 20dB]
Area of Spurious Attenuation : [within 9MHz to 12MHz]
Center frequency(fo) defined by the center of 3dB bandwidth.
17
5
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
■ Frequency Characteristics
8.00
0
7.50
1
7.50
1
7.00
2
7.00
2
6.50
3
6.50
3
6.00
4
6.00
4
5.50
5
5.50
5
5.00
6
5.00
6
4.50
4.50
7
10.620
10.660
10.700
Frequency (MHz)
10.740
10.780
10.500
10.900
4.00
SFELB10M7GA00-B0
1
6.50
1
6.00
2
6.00
2
5.50
3
5.50
3
5.00
4
5.00
4
4.50
5
4.50
5
4.00
6
4.00
6
3.50
3.50
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
5.50
1
5.00
2
4.50
3
4.00
4
3.50
5
3.00
6
2.50
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
2.00
G.D.T. (µsec.)
0
Attenuation (dB)
7.00
SFELB10M7FA00-B0
Attenuation (dB)
10.800
0
7
18
10.700
Frequency (MHz)
0
G.D.T. (µsec.)
Attenuation (dB)
SFELB10M7HA00-B0
10.600
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
6.50
3.00
G.D.T. (µsec.)
7
Attenuation (dB)
0
G.D.T. (µsec.)
Attenuation (dB)
5
SFELB10M7JA00-B0
G.D.T. (µsec.)
SFELB10M7KA00-B0
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Frequency Characteristics (Spurious)
SFELB10M7JA00-B0
0
10
10
20
20
Attenuation (dB)
Attenuation (dB)
SFELB10M7KA00-B0
0
30
40
30
40
50
50
60
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
70
8.700
12.700
0
0
10
10
20
20
30
40
60
60
10.700
Frequency (MHz)
11.700
12.700
5
40
50
9.700
11.700
30
50
70
8.700
10.700
Frequency (MHz)
SFELB10M7GA00-B0
Attenuation (dB)
Attenuation (dB)
SFELB10M7HA00-B0
9.700
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
SFELB10M7FA00-B0
0
10
Attenuation (dB)
20
30
40
50
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
19
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
CERAFILr Lower Spurious Response Type
7.5±2.0
SFELA10M7 series for FM-receivers are monolithic type
ceramic filters which use the energy trapped thickness
vibration-mode of the piezoelectric ceramic.
EIAJ
CODE
7.0±2.0
MARKING
0.5±0.1
2.5±0.2 2.5±0.2
3.0±1.0
SFELA10M7KAB0-B0
0.3±0.1
1. This type has lower spurious response compared to
the standard filters.
2. This types are suitable for higher spurious
suppression radio.
5.0±1.0
1.38±0.2
1.7±0.1
■ Features
(3)
(1)
(2)
7.5±2.0
7.5±2.0
MARKING
MARKING
EIAJ
CODE
0.5±0.1
(3)
(1)
(2)
(3)
(1)
(2)
7.5±2.0
7.5±2.0
MARKING
MARKING
EIAJ
CODE
EIAJ
CODE
0.5±0.1
(3)
(2)
SFELA10M7FAB0-B0
0.3±0.1
2.5±0.2 2.5±0.2
3.0±1.0
0.3±0.1
2.5±0.2 2.5±0.2
(1)
3.0±1.0
0.5±0.1
5.0±1.0
1.38±0.2
1.7±0.1
5.0±1.0
1.38±0.2
1.7±0.1
SFELA10M7GAB0-B0
3.0±1.0
SFELA10M7HAB0-B0
0.3±0.1
3.0±1.0
2.5±0.2 2.5±0.2
7.0±2.0
SFELA10M7JAB0-B0
0.3±0.1
2.5±0.2 2.5±0.2
7.0±2.0
0.5±0.1
5.0±1.0
1.38±0.2
1.7±0.1
5.0±1.0
1.38±0.2
1.7±0.1
7.0±2.0
EIAJ
CODE
7.0±2.0
6
(3)
(2)
(1)
Center Frequency (fo)
(MHz)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Insertion Loss
(dB)
Spurious Attenuation
(dB)
SFELA10M7KAB0-B0
10.700 ±30kHz
within110 ±30kHz
350 max.
7.0 ±2.0dB
45 min.
SFELA10M7JAB0-B0
10.700 ±30kHz
within150 ±40kHz
380 max.
5.5 ±2.0dB
45 min.
SFELA10M7HAB0-B0
10.700 ±30kHz
within180 ±40kHz
520 max.
5.0 ±2.0dB
45 min.
SFELA10M7GAB0-B0
10.700 ±30kHz
within230 ±50kHz
570 max.
3.0 ±2.0dB
45 min.
SFELA10M7FAB0-B0
10.700 ±30kHz
within280 ±50kHz
650 max.
3.0 ±2.0dB
45 min.
Part Number
Area of Attenuation : [within 20dB]
Area of Spurious Attenuation : [within 9MHz to 12MHz]
Center frequency(fo) defined by the center of 3dB bandwidth.
20
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
■ Frequency Characteristics
8.00
0
7.00
1
7.50
1
6.50
2
7.00
2
6.00
3
6.50
3
5.50
4
6.00
4
5.00
5
5.50
5
4.50
6
5.00
6
4.00
4.50
7
10.620
10.660
10.700
Frequency (MHz)
10.740
10.780
10.500
10.700
Frequency (MHz)
10.800
10.900
3.50
SFELA10M7GAB0-B0
6.50
0
6.00
1
6.00
1
5.50
2
5.50
2
5.00
3
5.00
3
4.50
4
4.50
4
4.00
5
4.00
5
3.50
6
3.50
6
3.00
3.00
7
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
Attenuation (dB)
0
G.D.T. (µsec.)
Attenuation (dB)
SFELA10M7HAB0-B0
10.600
6
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
7
Attenuation (dB)
0
G.D.T. (µsec.)
SFELA10M7JAB0-B0
G.D.T. (µsec.)
Attenuation (dB)
SFELA10M7KAB0-B0
2.50
5.00
1
4.50
2
4.00
3
3.50
4
3.00
5
2.50
6
2.00
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
Attenuation (dB)
SFELA10M7FAB0-B0
0
1.50
21
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Frequency Characteristics (Spurious)
SFELA10M7JAB0-B0
0
10
10
20
20
Attenuation (dB)
Attenuation (dB)
SFELA10M7KAB0-B0
0
30
40
30
40
50
50
60
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
70
12.700
8.700
SFELA10M7HAB0-B0
0
10
10
20
20
30
40
60
60
9.700
10.700
Frequency (MHz)
11.700
12.700
SFELA10M7FAB0-B0
0
10
Attenuation (dB)
20
30
40
50
60
70
22
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
40
50
8.700
11.700
30
50
70
10.700
Frequency (MHz)
SFELA10M7GAB0-B0
0
Attenuation (dB)
Attenuation (dB)
6
9.700
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
CERAFILr Wider Band-width Type
7.0±2.0
SFELA10M7 Series for FM-receivers are monolithic type
ceramic filters which use the energy trapped thickness
vibration-mode of the piezoelectric ceramic.
EIAJ
CODE
■ Features
7.0±2.0
MARKING
1. Realizes wider or narrower band characteristics not
obtained by conventional ceramic filters.
2. Temperature characteristics are the best available,
the same as those of Murata's conventional ceramic
filters. Thus, even in the case of narrow band
filters, the center frequency is stable even if
temperature changes.
5.0±1.0
1.38±0.2
1.7±0.1
0.5±0.1
3.0±1.0
SFELA10M7EA00-B0
0.3±0.1
2.5±0.2 2.5±0.2
(3)
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(1)
(2)
7.0±2.0
EIAJ
CODE
7.0±2.0
MARKING
7
5.0±1.0
1.38±0.2
1.7±0.1
0.5±0.1
3.0±1.0
SFELA10M7DF00-B0
0.3±0.1
2.5±0.2 2.5±0.2
(3)
Nominal
Center Frequency (fo)
Center Frequency(fn)
(MHz)
(MHz)
Part Number
(2)
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(1)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Insertion Loss
(dB)
Spurious Attenuation
(dB)
SFELA10M7EA00-B0
10.700 ±30kHz
-
within330 ±50kHz
680 max.
within4.0 ±2.0dB
30 min.
SFELA10M7DF00-B0
-
10.700
fn±175 min.
950 max.
within3.0 ±2.0dB
20 min.
Area of Attenuation : [within 20dB]
Area of Spurious Attenuation : [within 9MHz to 12MHz]
Center frequency(fo) defined by the center of 3dB bandwidth.
(fn) means nominal center frequency.
■ Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
23
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Frequency Characteristics
4.00
1
4.00
1
3.50
2
3.50
2
3.00
3
3.00
3
2.50
4
2.50
4
2.00
5
2.00
5
1.50
6
1.50
6
1.00
1.00
7
7
10.300
10.500
10.700
Frequency (MHz)
10.900
11.100
Attenuation (dB)
0
10.300
10.500
10.700
Frequency (MHz)
10.900
11.100
0.50
■ Frequency Characteristics (Spurious)
7
10
10
20
20
30
40
30
40
50
50
60
60
70
8.700
24
SFELA10M7DF00-B0
0
Attenuation (dB)
Attenuation (dB)
SFELA10M7EA00-B0
0
9.700
10.700
Frequency (MHz)
11.700
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
G.D.T. (µsec.)
SFELA10M7DF00-B0
4.50
G.D.T. (µsec.)
Attenuation (dB)
SFELA10M7EA00-B0
0
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
CERAFILr Narrow Band Type
10.0±2.0
SFELA10M7LFTA/KAH0, SFVLA/SFKLA series realizes
narrower band characteristics not obtained by
conventional ceramic filters. Besides, low spurious
and temperature characteristics is stable. This series
suits for European car-audio or AM up conversion use
that needs narrow band characteristics.
EIAJ
CODE
5.0±1.0
1.38±0.2
1.7±0.1
0.5±0.1
2.5±0.2 2.5±0.2
+1.5
3.5 –1.0
0.3±0.1
(3)
7.0 ±2.0
MARKING
MARKING
7.0 ±2.0
7.0 ±2.0
EIAJ
CODE
in mm
5.0 ±1.0
1 .4±0 .1
0. 5±0 .1
(1) : Input
(2) : Ground
(3) : Output
3.0 ±1.0
SFVLA10M7MF00-B0
(3)
(2)
2.5±0.2 2.5±0.2
0.3±0. 1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
3.0 ±1.0
1. 4±0. 1
0. 5±0. 1
5.0 ±1.0
1 .65 ±0. 1
1. 65±0.1
0.3±0. 1
(1)
(2)
7.0 ±2.0
SFKLA10M7NF00-B0
EI AJ
CODE
10.0±2.0
MARKING
SFVLA10M7LF00-B0
in mm
(1 )
(3)
(2)
in mm
(1 )
7.0±2.0
7.0± 2.0
1.38± 0.2
1.7± 0.1
0.5±0.1
2.5±0.2 2.5±0.2
(3)
(2)
(1)
(in mm)
SFELA10M7KAH0-B0
(1) Input
(2) Ground
(3) Output
3.0±1.0
3.0± 1.0
0.3± 0.1
2.5
2.5
± 0.2 ± 0.2
SFELA10M7LFTA01-B0
5.0±1.0
1.38±0.2
1.7±0.1
5.0±1.0
0.5± 0.1
(3)
Part Number
7.0±2.0
EIAJ
CODE
0.3±0.1
EIAJ
CODE
7.0± 2.0
MARKING
MARKING
Nominal
Center Frequency (fo)
Center Frequency(fn)
(MHz)
(MHz)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
(2)
(1) : Input
(2) : Ground
(3) : Output
Insertion Loss
(dB)
Spurious Attenuation
(dB)
SFKLA10M7NF00-B0
10.700 ±15kHz
-
20 min.
95 max.
6.0 max.
24 min.
SFVLA10M7MF00-B0
-
10.700
fn±13 min.
135 max.
within5.5 ±2.5dB
30 min.
SFVLA10M7LF00-B0
-
10.700
fn±25 min.
200 max.
within5.5 ±2.5dB
30 min.
SFELA10M7LFTA-B0
-
10.700
fn±25 min.
280 max.
within7.0 ±2.0dB
30 min.
SFELA10M7KAH0-B0
10.700 ±30kHz
-
within110 ±30kHz
350 max.
within7.0 ±2.0dB
30 min.
Area of Attenuation : [within 20dB]
(in mm)
(1)
Area of Spurious Attenuation : [within 9MHz to 12MHz]
25
8
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
■ Frequency Characteristics
SFVLA10M7MF00-B0
Attenuation (dB)
Attenuation ( dB )
0
19.0
1
18.0
2
17.0
3
16.0
4
15.0
5
14.0
6
13.0
G.D.T. (µsec.)
SFKLA10M7NF00-B0
0
10
10.650
10.750
10.700
7
10.620
10.660
Frequency ( kHz )
8
13.0
1
12.0
2
11.0
3
10.0
4
9.00
5
8.00
6
7.00
10.620
10.660
10.700
Frequency (MHz)
10.740
10.780
1
7.50
2
7.00
3
6.50
4
6.00
5
5.50
6
5.00
26
10.700
Frequency (MHz)
10.740
10.780
4.50
G.D.T. (µsec.)
Attenuation (dB)
8.00
10.660
12.0
0
11.00
10.50
2
10.00
3
9.50
4
9.00
5
8.50
6
8.00
7
7.50
8
7.00
10.580
10.640
10.700
Frequency (MHz)
SFELA10M7KAH0-B0
10.620
10.780
1
9
6.00
0
7
Attenuation (dB)
0
7
10.740
SFELA10M7LFTA01-B0
G.D.T. (µsec.)
Attenuation (dB)
SFVLA10M7LF00-B0
10.700
Frequency (MHz)
10.760
10.820
6.50
G.D.T. (µsec.)
10.600
10.800
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Frequency Characteristics (Spurious)
SFKLA10M7NF00-B0
SFVLA10M7MF00-B0
0
0
10
10
20
Attenuation (dB)
Attenuation ( dB )
20
30
40
50
30
40
50
60
60
70
9.700
10.200
11.200
10.700
70
8.700
11.700
9.700
Frequency ( MHz )
SFVLA10M7LF00-B0
10.700
Frequency (MHz)
11.700
12.700
SFELA10M7LFTA01-B0
0
0
10
10
20
Attenuation (dB)
Attenuation (dB)
20
30
40
50
30
40
50
60
70
60
70
8.700
80
9.700
10.700
Frequency (MHz)
11.700
12.700
90
9.700
10.200
10.700
Frequency (MHz)
11.200
11.700
8
SFELA10M7KAH0-B0
0
10
Attenuation (dB)
20
30
40
50
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
27
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
CERAFILr For FM -IF Tuners
9.0 max.
SFELA10M7 series for FM-receivers are monolithic type
ceramic filters which use the energy trapped thickness
vibration-mode of the piezoelectric ceramic.
EIAJ
CODE
0.3 ±0.1
0.5 ±0. 1
4.0 max.
SFELA10M7JAXE-B0
2.5±0.2 2.5±0.2
(3 )
(2)
(1 )
7.0±2.0
7.0±2.0
MARKING
EIAJ
CODE
5.0±1.0
1.38±0.2
1.7±0.1
0.5±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
3.0±1.0
SFELA10M7HA0G-B0
0.3±0.1
1. Little dispersion of amplitude characteristics and
phase characteristics (G. D. T. characteristics).
2. The SFELA10M7G_X series has G. D. T characteristics
and is useful for obtaining low distortion.
SFELA10M7F_L series, in these ceramic filters,
being in harmony with flatness of G. D. T. ,
roundness of the amplitude and selectivity
characteristics, therefore, these ceramic filters
are suitable to high-grade stereo tuners. Even if
mismatching condition, they can keep little
distortion because of low Qm of ceramic material.
The SFELA10M7FA0G series is based on
SFELA10M7FA00/GA00/HA00, and it obtains high
selectivity with low loss.
There is little dispersion of amplitude and
G. D. T. characteristics, and low distortion rate
can be obtained.
3. All products are inspected for symmetry and
roundness of amplitude characteristics, and the
flatness of G. D. T. characteristics.
5.0 ±1.0
1. 38 ±0.2
1. 7±0 .1
■ Features
(3)
(in mm)
(1)
(2)
9.0 max.
10 .0 max.
MARKING
EIAJ
CODE
5. 0±1 .0
1. 38 ±0.2
1. 7±0 .1
0. 3±0 .1
0.5 ±0. 1
4.0 max.
2.5±0.2 2.5±0.2
(3 )
(1 )
7.0±2.0
MARKING
MARKING
7.0±2.0
7.0±2.0
EIAJ
CODE
EIAJ
CODE
0.5±0.1
3.0±1.0
2.5±0.2 2.5±0.2
(3)
(2)
(1)
(1) : Input
(2) : Ground
(3) : Output
SFELA10M7GALM-B0
0.3±0.1
2.5±0.2 2.5±0.2
3.0±1.0
0.5±0.1
5.0±1.0
1.38±0.2
1.7±0.1
5.0±1.0
1.38±0.2
1.7±0.1
SFELA10M7GA0G-B0
( 2)
7.0±2.0
SFELA10M7HAXD-B0
0.3±0.1
9
10. 0 ma x.
MARKING
(in mm)
(3)
(2)
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(1)
Continued on the following page.
28
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Continued from the preceding page.
7.0±2.0
9. 0 ma x.
0.5±0.1
2.5±0.2 2.5±0.2
(2 )
SFELA10M7FA0G-B0
3.0±1.0
4.0 max.
(3)
0.3±0.1
2.5±0.2 2.5±0.2
(1) : Input
(2) : Ground
(3) : Output
in mm
(1 )
(3)
7.0±2.0
7.0±2.0
MARKING
EIAJ
CODE
EIAJ
CODE
5.0±1.0
0.5 ±0. 1
(1) : Input
(2) : Ground
(3) : Output
SFELA10M7GAXX-B0
(in mm)
(3)
(1)
(2)
2.5±0.2 2.5±0.2
4.0 max.
3.0±1.0
0.3±0.1
2.5±0.2 2.5±0.2
0.3 ±0.1
0.5±0.1
5.0 ±1.0
1. 38 ±0.2
1. 7±0 .1
1.38±0.2
1.7±0.1
(3)
(in mm)
(1)
(2)
9.0 max.
MARKING
SFELA10M7GALP03-B0
(1) : Input
(2) : Ground
(3) : Output
11. 0 ma x.
0.3 ±0.1
0. 5±0.1
7.0±2.0
1.38±0.2
1.7±0.1
5.0 ±1.0
1. 38±0. 2
1. 7±0. 1
EIAJ
CODE
5.0±1.0
EI AJ
CODE
SFELA10M7GAXA-B0
MARKING
11. 0 ma x.
MARKING
(2)
(1 )
(1) : Input
(2) : Ground
(3) : Output
in mm
7.0±2.0
7.0±2.0
MARKING
EIAJ
CODE
9
5.0±1.0
1.38±0.2
1.7±0.1
0.5±0.1
3.0±1.0
SFELA10M7FALL-B0
0.3±0.1
2.5±0.2 2.5±0.2
(3)
Part Number
(2)
(1) : Input
(2) : Ground
(3) : Output
(in mm)
(1)
Center Frequency (fo) 3dB Bandwidth Attenuation Insertion Loss Spurious Attenuation
(MHz)
(kHz)
(kHz)
(dB)
(dB)
GDT Bandwidth
(kHz)
SFELA10M7JAXE-B0
10.700 ±30kHz
within150 ±30kHz
500 max.
14.0 max.
35 min.
SFELA10M7HA0G-B0
10.700 ±30kHz
within180 ±40kHz
520 max.
7.0 max.
40 min.
fo±45 min.[within 0.5µsec.]
SFELA10M7HAXD-B0
10.700 ±30kHz
within180 ±30kHz
530 max.
14.0 max.
33 min.
fo±60 min.[within 0.15µsec.]
SFELA10M7GA0G-B0
10.700 ±30kHz
within230 ±50kHz
600 max.
7.0 max.
40 min.
fo±60 min.[within 0.5µsec.]
SFELA10M7GALM-B0
10.700 ±30kHz
within230 ±50kHz
600 max. within9.0 ±2.0dB
30 min.
fo±60 min.[within 0.25µsec.]
SFELA10M7GAXA-B0
10.700 ±30kHz
within220 ±40kHz
610 max.
30 min.
fo±80 min.[within 0.15µsec.]
SFELA10M7FA0G-B0
10.700 ±30kHz
within280 ±50kHz
650 max. within4.0 ±2.0dB
30 min.
fo±85 min.[within 0.5µsec.]
SFELA10M7GALP03-B0
10.700 ±30kHz
within250 ±50kHz
650 max.
10.0 max.
30 min.
fo±65 min.[within 0.25µsec.]
SFELA10M7GAXX-B0
10.700 ±30kHz
within250 ±40kHz
670 max.
12.0 max.
25 min.
fo±110 min.[within 0.2µsec.]
SFELA10M7FALL-B0
10.700 ±30kHz
within280 ±50kHz
700 max. within7.0 ±2.0dB
25 min.
fo±70 min.[within 0.25µsec.]
12.5 max.
fo±50 min.[within 0.15µsec.]
Area of Attenuation : [within 20dB]
Area of Spurious Attenuation : [within 9MHz to 12MHz]
Center frequency(fo) defined by the center of 3dB bandwidth.
29
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
■ Freq. Characteristics
5.00
0
6.00
1
4.75
1
5.50
2
4.50
2
5.00
3
4.25
3
4.50
4
4.00
4
4.00
5
3.75
5
3.50
6
3.50
6
3.00
3.25
7
10.600
10.700
Frequency (MHz)
10.800
10.900
10.500
SFELA10M7HAXD-B0
10.800
10.900
2.50
SFELA10M7GA0G-B0
0
6.00
1
4.25
1
5.50
2
4.00
2
5.00
3
3.75
3
4.50
4
3.50
4
4.00
5
3.25
5
3.50
6
3.00
6
3.00
2.75
7
0
4.00
0
3.75
1
3.75
1
3.50
2
3.50
2
3.25
3
3.25
3
3.00
4
3.00
4
2.75
5
2.75
5
2.50
6
2.50
6
2.25
2.25
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
Attenuation (dB)
4.50
7
10.500
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.600
10.700
Frequency (MHz)
10.800
10.900
2.50
10.900
Attenuation (dB)
SFELA10M7GAXA-B0
G.D.T. (µsec.)
SFELA10M7GALM-B0
Attenuation (dB)
10.700
Frequency (MHz)
0
G.D.T. (µsec.)
Attenuation (dB)
9
10.600
G.D.T. (µsec.)
10.500
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
7
Attenuation (dB)
0
G.D.T. (µsec.)
SFELA10M7HA0G-B0
G.D.T. (µsec.)
Attenuation (dB)
SFELA10M7JAXE-B0
2.00
Continued on the following page.
30
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Continued from the preceding page.
■ Freq. Characteristics
3.75
1
4.50
1
3.50
2
4.00
2
3.25
3
3.50
3
3.00
4
3.00
4
2.75
5
2.50
5
2.50
6
2.00
6
2.25
1.50
7
0
3.25
0
3.25
1
3.00
1
3.00
2
2.75
2
2.75
3
2.50
3
2.50
4
2.25
4
2.25
5
2.00
5
2.00
6
1.75
6
1.75
1.50
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
10.500
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.700
Frequency (MHz)
10.800
10.900
2.00
10.900
Attenuation (dB)
SFELA10M7FALL-B0
G.D.T. (µsec.)
Attenuation (dB)
SFELA10M7GAXX-B0
10.600
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
7
Attenuation (dB)
0
G.D.T. (µsec.)
SFELA10M7GALP03-B0
5.00
G.D.T. (µsec.)
Attenuation (dB)
SFELA10M7FA0G-B0
0
1.50
■ Spurious Frequency
0
10
10
20
20
30
40
30
40
50
50
60
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
70
9.900
12.700
10
10
20
20
30
40
60
60
11.700
11.100
11.500
40
50
10.700
Frequency (MHz)
10.700
Frequency (MHz)
30
50
9.700
10.300
SFELA10M7GA0G-B0
0
Attenuation (dB)
Attenuation (dB)
SFELA10M7HAXD-B0
0
70
8.700
9
SFELA10M7HA0G-B0
0
Attenuation (dB)
Attenuation (dB)
SFELA10M7JAXE-B0
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
Continued on the following page.
31
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Continued from the preceding page.
■ Spurious Frequency
SFELA10M7GAXA-B0
0
10
10
20
20
Attenuation (dB)
Attenuation (dB)
SFELA10M7GALM-B0
0
30
40
30
40
50
50
60
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
70
8.700
12.700
0
10
10
20
20
30
40
60
60
9
10.700
Frequency (MHz)
11.700
70
8.700
12.700
10
10
20
20
30
40
32
11.700
12.700
40
50
60
60
10.700
Frequency (MHz)
10.700
Frequency (MHz)
30
50
9.700
9.700
SFELA10M7FALL-B0
0
Attenuation (dB)
Attenuation (dB)
SFELA10M7GAXX-B0
0
70
8.700
12.700
40
50
9.700
11.700
30
50
70
8.700
10.700
Frequency (MHz)
SFELA10M7GALP03-B0
0
Attenuation (dB)
Attenuation (dB)
SFELA10M7FA0G-B0
9.700
11.700
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
CERAFILr Three-Elements Type SFTLA Series
10.0±1.0
SFTLA10M7 series for FM-receivers are monolithic type
ceramic filters which use the energy trapped thickness
vibration-mode of the piezoelectric ceramic.
EIAJ
CODE
6.0±1.0
MARKING
0.4±0.1
■ Features
1.4±0.1
0.5±0.1
2.5±0.2 2.5±0.2
3.0±1.0
SFTLA10M7HA00-B0
0.3±0.1
(3)
(2)
(1) : Input
(2) : Ground
(3) : Output
in mm
(1)
10.0±1.0
MARKING
EIAJ
CODE
6.0±1.0
1. It has an excellent shape factor, and it is
possible to obtain 1.5 times more excellent
selectivity than SFELA10M7 series (by detuning
+-300 or 400kHz).
2. Good performance of spurious suppression.
3. Having the same terminal pitch as the SFELA10M7
series, it easily replaces that series.
4. By replacing two SFELA10M7 series filters with one
SFTLA10M7 filter,more compact sets can be made.
5. Well-suited for 1-chip ICs.
5.0±1.0
0.65±0.1
0.4±0.1
5.0±1.0
0.65±0.1
1.4±0.1
0.5±0.1
3.0±1.0
SFTLA10M7GA00-B0
0.3±0.1
2.5±0.2 2.5±0.2
(3)
(2)
(1) : Input
(2) : Ground
(3) : Output
in mm
(1)
10.0±1.0
EIAJ
CODE
6.0±1.0
MARKING
10
0.4±0.1
5.0±1.0
0.65±0.1
1.4±0.1
0.5±0.1
3.0±1.0
SFTLA10M7FA00-B0
0.3±0.1
2.5±0.2 2.5±0.2
(3)
(2)
(1) : Input
(2) : Ground
(3) : Output
in mm
(1)
Center Frequency (fo)
(MHz)
3dB Bandwidth
(kHz)
Attenuation
(kHz)
Insertion Loss
(dB)
Spurious Attenuation
(dB)
SFTLA10M7HA00-B0
10.700 ±30kHz
within180 ±40kHz
550 max.
within5.5 ±2.5dB
50 min.
SFTLA10M7GA00-B0
10.700 ±30kHz
within230 ±40kHz
650 max.
within6.0 ±2.0dB
50 min.
SFTLA10M7FA00-B0
10.700 ±30kHz
within280 ±50kHz
700 max.
within6.0 ±2.0dB
50 min.
Part Number
Area of Attenuation : [within 40dB]
Area of Spurious Attenuation : [within 9MHz to 12MHz]
Center frequency(fo) defined by the center of 3dB bandwidth.
33
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
■ Frequency Characteristics
8.00
0
7.00
1
7.50
1
6.50
2
7.00
2
6.00
3
6.50
3
5.50
4
6.00
4
5.00
5
5.50
5
4.50
6
5.00
6
4.00
4.50
7
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
Attenuation (dB)
0
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
SFTLA10M7GA00-B0
G.D.T. (µsec.)
Attenuation (dB)
SFTLA10M7HA00-B0
3.50
10
6.00
1
5.50
2
5.00
3
4.50
4
4.00
5
3.50
6
3.00
7
10.500
10.600
10.700
Frequency (MHz)
10.800
10.900
G.D.T. (µsec.)
Attenuation (dB)
SFTLA10M7FA00-B0
0
2.50
■ Frequency Characteristics (Spurious)
SFTLA10M7GA00-B0
0
10
10
20
20
Attenuation (dB)
Attenuation (dB)
SFTLA10M7HA00-B0
0
30
40
30
40
50
50
60
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
Continued on the following page.
34
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Continued from the preceding page.
■ Frequency Characteristics (Spurious)
SFTLA10M7FA00-B0
0
10
Attenuation (dB)
20
30
40
50
60
70
8.700
9.700
10.700
Frequency (MHz)
11.700
12.700
10
35
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Lead Type CERAFILr Test Circuit and Characteristics Data
■ Test Circuit
(1)
R1
(2)
(1) : Input
(2) : Output
(3) :Ground
(3)
RF
Rg
R2
Voltmeter
C
S.S.G
Rg + R1 = R2 = 330Ω
C = 10pF (Including stray capacitance and input
capacitance of RF voltmeter.)
W20
Center frequency
SFELA10M7GA00-B0
Variation (kHz)
W40
0
Y20
W2
W1
Y20
0
W20
W40
Temperature (˚C)
W60
W80
Insertion loss
Variation (dB)
Y40
0
Y1
Y2
W40
W20
Y20
0
W20
W40
Temperature (˚C)
W60
W80
Variation (kHz)
Variation (kHz)
Variation (dB)
Variation (kHz)
■ Temperature Characteristics
3dB Band width
0
Y20
Y40
Y20
0
W20
W40
Temperature (˚C)
W60
W80
W40
W20
Center frequency
SFELA10M7HA00-B0
0
Y20
Y40
W2
W1
Y20
0
W20
W40
Temperature (˚C)
W60
W80
0
W20
W40
Temperature (˚C)
W60
W80
0
W20
W40
Temperature (˚C)
W60
W80
Insertion loss
0
Y1
Y2
W40
W20
Y20
3dB Band width
0
Y20
Y40
Y20
■ Matching Conditions
10
•When using ceramic filters, it is most important to
match the input/output load to impedance 330 ohm
(only SFELA10M7DF00-B0 is 470 ohm matching).
Waveform symmetry is damaged when reactance
is added to the input/output load.
•Two ceramic filters directly connected can be used
for high selelctivity. For reducing waveform
variation, it is recommended to input a buffer AMP
between ceramic filters.
36
•The SFELA10M7 and SFTLA10M7 series are of
input/output symmetric structure so that in theory
there is no input/output directionality. Actual
circuits may use different input/output loading
conditions (for example, mismatched impedance) or
capacitance load. In such cases, the waveform will
be a little changed by the direction of the
input/output of the ceramic filters.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Lead Type CERAFILr Characteristics Data and Notice
■ Loaded Resistance and Waveform (Rg+R1=330ohm)
1.2
1.0
0.8
0.6
0.4
0.2
0
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
1.2
1.0
0.8
0.6
0.4
0.2
0
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
R2=1kΩ
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
Group Delay Time (µsec.)
Attenuation (dB)
0
1
2
3
4
5
6
7
Group Delay Time (µsec.)
Attenuation (dB)
R2=560Ω
0
1
2
3
4
5
6
7
R2=330Ω
Attenuation (dB)
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
Group Delay Time (µsec.)
Attenuation (dB)
1.2
1.0
0.8
0.6
0.4
0.2
0
Group Delay Time (µsec.)
SFELA10M7GA00-B0
R2=220Ω
0
1
2
3
4
5
6
7
■ Loaded Capacitance and Waveform (Rg+R1=R2=330ohm)
Attenuation (dB)
C=56pF
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
1.2
1.0
0.8
0.6
0.4
0.2
0
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
C=82pF
0
1
2
3
4
5
6
7
1.2
1.0
0.8
0.6
0.4
0.2
0
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
Group Delay Time (µsec.)
Attenuation (dB)
0
1
2
3
4
5
6
7
Group Delay Time (µsec.)
10.5 10.6 10.7 10.8 10.9
Frequency (MHz)
C=33pF
Attenuation (dB)
1.2
1.0
0.8
0.6
0.4
0.2
0
Group Delay Time (µsec.)
Attenuation (dB)
0
1
2
3
4
5
6
7
Group Delay Time (µsec.)
SFELA10M7GA00-B0
C=10pF
■ Notice (Soldering and Mounting)
The component cannot be withstand washing.
10
■ Notice (Handling)
1. Do not use this product with bend. The component
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
2. The component may be damaged when an excess stress
will be applied.
3. All kinds of re-flow soldering must not be applied
on the component.
4. Do not clean or wash the component as it is not
hermetically sealed.
5. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in flow soldering.
6. In case of covering discriminator with over coat,
conditions such as material of resin, cure
temperature, and so on should be evaluated well.
7. Accurate test circuit values are required to
measure electrical characteristics. It may be a
cause of mis-correlation if there is any deviation,
especially stray capacitance, from the test
circuit in the specification.
37
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
Discriminators Chip Type CDACV Series
1.5±0.3
3.4±0.5
∗
2.6±0.3
∗∗
CDACV10M7 series forms a resonator on a piezoelectric
ceramic substrate. In combination with ICs, this type
obtains stable demodulation characteristics in wide
bandwidths.
■ Features
0.9±0.3
0.9±0.3
1. Compact and excellent mechanical strength.
2. Can be combined with various ICs. The IC is
determined by the last number in the part number.
3. Stable demodulation characteristics can be obtained
without adjustment.
4. The MG type for wide bandwidths and the MC type for
narrow bandwidths are available.
5. Stable temperature characteristics.
6. We recommend kits : ceramic discriminator
CDACV10M7 series and "CERAFIL" SFECV10M7 of the
same frequency rank.
∗ : EIAJ Monthly Code
∗∗ : Rank
in mm
Center Frequency (fo) Recovered Audio 3dB BW Recovered Audio Output Distortion
(MHz)
(kHz)
(mV)
(%)
Part Number
IC
Detection Method
CDACV10M7GA001-R0
10.700 ±30kHz
fo±150 min.
55 min.
1.0 max.
CX20029
Quadrature
CDACV10M7GA016-R0
10.700 ±30kHz
300 min.
within60 to 90mV
0.9 max.
TA8122F
Quadrature
CDACV10M7GA046-R0
10.700 ±30kHz
330 min.
280 min.
1.5 max.
LA1832
Quadrature
CDACV10M7GA069-R0
10.700 ±30kHz
330 min.
80 min.
1.0 max.
CXA1538N
Quadrature
CDACV10M7CA001-R0
10.700 ±30kHz
fo±150 min.
55 min.
1.0 max.
CX20091
Quadrature
■ Center Frequency Rank Code
11
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
■ Standard Land Pattern Dimensions
1.5
2.6
1.5
1.4
38
1.5
1.4
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ CDACV10M7GA001-R0
Test Circuit
Frequency Characteristics
100
1000
AFC
REF
33
1µ
32
39
AF OUTPUT
–
AF Output
28
CDALA10M7GA001
10
100
100k
Fg=50
9
S.S.G.
+
CX20029
Vcc=+3.0V
Unit
R:Ω
C:F
Distortion (%)
0.01µ
Recovered AF Output Voltage (mV)
5
280
1
10
Distortion
0.1
1
Input signal conditions
Input Level
Mod. Freq.
Freq.Dev.
10.4
10.5
10.6 10.7 10.8
Frequency (MHz)
10.9
100dBµ
1000Hz
±22.5kHz
11.0
■ CDACV10M7GA016-R0
Test Circuit
Frequency Characteristics
2.5µ
0.1µ
100
4
5
6
7
8
9 10 11 12
0.022µ
3
+
22µ
2
Recovered AF Output Voltage (mV)
TA8122F (TOSHIBA)
CDACV10M7GA016
SFELA10M7DF00
Unit
R:Ω
C:F
270
0.022µ
IF in
10
AF Output
1
10
Distortion
Distortion (%)
24k
0.033µ
+
24 23 22 21 20 19 18 17 16 15 14 13
1
100
1000
DC Out AF Out
330p
1k
VCC +3V
0.1
1
Input signal conditions
Input Level
Mod. Freq.
Freq.Dev.
10.4
10.5
10.6
10.7
10.8
Frequency (MHz)
10.9
80dBµ
1000Hz
±22.5kHz
11.0
11
■ CDACV10M7GA046-R0
Test Circuit
Frequency Characteristics
AF OUT
100
1000
CSBLA456KE2ZF15 0.01µ
+
1µ
+
3.3µ
24
23
22
1
2
3
21
20
LA1832
6.8k
4
5
300
18
17
16
15
7
8
9
10
CDALA10M7GA046
2.2µ
75
10µ
+
1µ
14
13
11
12
3k
1µ
0.047µ
+
REG
Vcc (5V)
10
100
(SANYO)
6
270
0.047µ
IF-IN
19
AF Output
0.01µ
+
100µ
Unit
R:Ω
C:F
Distortion
1
10
Distortion (%)
AFC
1200p
+ 22µ
0.047µ
Recovered AF Output Voltage (mV)
5.6k
0.1
1
Input signal conditions
Input Level
Mod. Freq.
Freq.Dev.
10.4
10.5
10.6
10.7
10.8
Frequency (MHz)
10.9
112dBµ
1000Hz
±75kHz
11.0
Continued on the following page.
39
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Continued from the preceding page.
■ CDACV10M7GA069-R0
Test Circuit
Frequency Characteristics
CDACV10M7GZ069-B0 VCC (3V)
Reg
3.3µ
2.2k 0.01µ
+
100
10µ
100
1000
10µ
+
+
28
27
26
25
24
23
22
21
20
19
18
17
16
10
11
12
13
14
15
3
4
5
6
7
8
100 µ
0.01µ
+ +
9
+
1µ
1µ
2
33µ
1
+
4.7µ
CXA1538N
0.01µ 0.01µ
+
AF OUT
0.022µ
VCC (3V)
3.3k
0.022µ
AFC
IF IN
Unit
R:Ω
C:F
3.3k
10
100
10
Distortion (%)
29
Recovered AF Output Voltage (mV)
AF Output
30
1
Distortion
0.1
1
Input signal conditions
10.4
10.5
10.6
10.7
10.8
10.9
11.0
Frequency (MHz)
Input Level
100dBµ
Mod.Freq.
1000Hz
Freq.Dev.
±75kHz
■ CDACV10M7CA001-R0
Test Circuit
25
24
23
22
20
19
18
17
16
15
CX20091 (SONY)
2
3
4
5
6
4.7µ
100
+
7
8
9
10
11
12
13
14
1000p
1
CDACV10M7CZ001-B0 REG OUT
10
100
10
0.01µ
0.01µ 280
21
1000
Unit
R:Ω
C:F
AF Output
10
1
Distortion (%)
26
+
Recovered AF Output Voltage (mV)
27
Frequency Characteristics
INPUT
S.S.G.(Rg=50)
+
+
28
AFC OUT
10µ
4.7µ
0.022µ
100µ
+
AF OUT
10µ
Vcc 3V
Distortion
0.1
1
Input signal conditions
10.4
10.5
10.6
10.7
10.8
Frequency (MHz)
11
40
10.9
11.0
Input Level
100dBµ
Mod.Freq.
1000Hz
Freq.Dev.
±22.5kHz
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Chip Type Discriminators CDACV Series Notice
■ Notice (soldering and mounting)
1. Standard Reflow Soldering Condition
(1) Reflow
5sec.
240
Temperature (˚C)
230
Gradual
Cooling
150
60
30
Time (sec.)
(2) Soldering Iron
Lead terminal is directly contacted with the tip of
soldering iron of 280±5˚C for 3.0±0.5 seconds.
2. Wash
The component cannot be withstand washing.
■ Notice (handling)
1. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
2. Design layout of components on the PC board to
minimize the stress imposed on the warp or flexure of the
board.
3. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause destruction
resistance characteristics to lower. To prevent this, be
extremely careful in determining shape and dimension
before designing the circuit board diagram.
4. When the positioning claws and pick up nozzle are worn,
the load is applied to the chip while positioning is
concentrated to one positioning accuracy, etc. Careful
checking and maintenance are necessary to prevent
unexpected trouble.
5. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component. Depending on the soldering conditions, the
effective area of terminations may be reduced. the use of
solder containing Ag should be done to prevent the
electrode erosion.
6. Do not clean or wash the component as it is not
hermetically sealed.
7. In case of covering discriminator with over coat,
conditions such as material of resin, cure temperature,
and so on should be evaluated well.
8. Accurate test circuit values are required to measure
electrical characteristics.
It may be a cause of mis-correlation if there is any
deviation, especially stray capacitance, from the test
circuit in the specification.
[Component direction]
Put the
component
lateral to the
direction in
which stress
acts.
[Component layout close to board]
Perforation
A
B
Slit
C
Susceptibility to
stress is in the order
of : A>C>B
11
41
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
0.3±0.2
Discriminators Chip Low-profile Type CDSCA Series
0.2±0.2
1.4max
1.2max
0.4(ref.)
1. Compact and high reliability and recommended for
automotive applications.
2. Can be combined with various ICs. The IC is
determined by the last number in the part number.
3. Stable demoduration characteristics can be
obtained without adjustment.
4. Stable temperature characteristics.
5. Recommended for Pb free soldering.
Part Number
10.700 (fn)
fn±80 min.
■ Standard Land Pattern Dimensions
2.6
3.0
2.0
0.8±0.1
1.5±0.1
(fn) means nominal center frequency.
1.0
0.4(ref.)
0.8±0.1
Center Frequency (fo) Recovered Audio 3dB BW Recovered Audio Output Distortion
(MHz)
(kHz)
(mV)
(%)
CDSCA10M7GF107-R0
1.0
(in mm)
42
0.4±0.05
4.1max
■ Features
12
4.5±0.1
2.0±0.1
CDSCA10M7 series forms a resonator on a piezo electric
ceramic sabstrate. In combination with ICs, this type
obtains stable demoduration characteristics in wide
bandwidth.
52 min.
3.0 max.
1.5±0.1
(in mm)
IC
Detection Method
TA31272F
Quadrature
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
■ Test Circuit
P61E7.pdf 01.10.17
■ Frequency Characteristics
Vcc (5.0V)
AF OUT
0.01µF
100
1000
0.01µF
5
0.01µF
S.S.G.
6
7
8
9
10 11 12
1000pF
4
0.01µF
3
0.01µF
2
0.1µF
X
R
C
0.1µF
X: CDSCA10M7GF107-B0
R: 1.2 [kohm]
C: open
100
10
AF Output
Distortion
1
10
Distortion (%)
TA31272F
1
Recovered AF Output Voltage (mV)
24 23 22 21 20 19 18 17 16 15 14 13
Input signal conditions
0.1
1
Input Level
Mod. Freq.
Freq.Dev.
10.4
10.5
10.6
10.7
10.8
Frequency (MHz)
10.9
100dBµ
1000Hz
±40kHz
11.0
12
43
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Chip Type Discriminators CDSCA Series Notice
■ Notice (Soldering and Mounting)
1. Standard Reflow Soldering Condition
(1) Reflow
5 sec
260
Temperature (°C)
240
Gradual
Cooling
150
60
60
Time (sec.)
(2) Soldering Iron
Lead terminal is directly contacted with the tip of
soldering iron of +280±5°C for 3.0 seconds±0.5 seconds.
2. Wash
The component cannot be withstand washing.
■ Notice (Handling)
12
1. The component mounted on the PCB may be damaged if
excess mechanical stress is applied.
2. Layout the components on the PCB to minimize the
stress imposed by the warp or flexure of the board.
3. After installing components, if solder is excessively
applied to the circuit board, mechanical stress will cause
destruction resistance characteristics to be lower. To
prevent this, be extremely careful in determining shape
and dimension before designing the circuit board diagram.
4. When the positioning claw or pick up nozzle are worn, the
excess load is applied to the components while
positioning or placing are performed. Careful checking
and maintenance are necessary to prevent unexpected
trouble.
5. When correcting component's position with a soldering
iron, the tip of the soldering iron should not directly touch
the chip component. Depending on the soldering
conditions, the effective area of terminations may be
reduced. The use of solder containing Ag should be
considerd to prevent the electrode erosion.
6. Do not clean or wash the component as it is not
hermetically sealed.
7. In case of overcoating the part, coating conditions such
as material, curing temperature, and so on must be
evaluated deeply.
8. Accurate test circuit values are required to measure
electrical characteristics.
It may be a cause of mis-correlation if there is any
deviation, especially stray capacitance, from the test
circuit in the specification.
44
[Component direction]
Put the
component
laterally to the
direction in
which stress
acts.
[Component layout close to board]
Perforation B
A
Slit
C
Susceptibility to
stress is in the order
of : A>C>B
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Ceramic Filters (CERAFILr) for FM Receivers
Discriminators CDALA Series
8.0±1.0
Freq. Rank (Color Dot)
EIAJ
CODE
MARKING
5.0±1.0
CDALA10M7 series forms a resonator on a piezoelectric
ceramic substrate. In combination with ICs, this type
obtains stable demodulation characteristics in wide
bandwidths.
5.0±1.0
0.4±0.1
0.65±0.1
■ Features
3.0±1.0
5.0±0.2
CDALA10M7G_ Series
(in mm)
8.0±1.0
Freq. Rank (Color Dot)
EIAJ
CODE
MARKING
5.0±1.0
1. Compact and excellent mechanical strength.
2. Can be combined with various ICs. The IC is
determined by the last number in the part number.
3. Stable demodulation characteristics can be obtained
without adjustment.
4. The MG type for wide bandwidths and the MC type for
narrow bandwidths are available.
5. Stable temperature characteristics.
6. We recommend combination : ceramic discriminator
CDALA10M7 series and "CERAFIL" SFELA10M7 of the
same frequency rank.
0.3±0.1
0.5±0.1
5.0±1.0
0.4±0.1
0.65±0.1
0.3±0.1
0.5±0.1
3.0±1.0
5.0±0.2
CDALA10M7C_ Series
(in mm)
Center Frequency (fo) Recovered Audio 3dB BW Recovered Audio Output Distortion
(MHz)
(kHz)
(mV)
(%)
Part Number
IC
Detection Method
CDALA10M7GA001-B0
10.700 ±30kHz
345 min.
25 min.
0.6 max.
CX20029
Quadrature
CDALA10M7GA016-B0
10.700 ±30kHz
300 min.
within60 to 90mV
0.9 max.
TA8122F
Quadrature
CDALA10M7GA018-B0
10.700 ±30kHz
300 min.
60 min.
0.9 max.
TA8132N
Quadrature
CDALA10M7GA046-B0
10.700 ±30kHz
330 min.
280 min.
1.0 max.
LA1832
Quadrature
CDALA10M7GA048-B0
10.700 ±30kHz
400 min.
700 min.
1.0 max.
LA1835
Quadrature
CDALA10M7GA092-B0
10.700 ±30kHz
300 min.
60 min.
1.0 max.
TA2132P
Quadrature
CDALA10M7CA001-B0
10.700 ±30kHz
242 min.
35 min.
-
CX20091
Quadrature
CDALA10M7CA005A-B0
10.700 ±30kHz
100 min.
600 min.
6.0 max.
LA7770
Quadrature
CDALA10M7CA040-B0
10.700 ±30kHz
130 min.
40 min.
0.7 max.
TEA5710
Quadrature
■ Center Frequency Rank Code
CODE
30kHz Step
25kHz Step
D
10.64MHz±30kHz
10.650MHz±25kHz
B
10.67MHz±30kHz
10.675MHz±25kHz
A
10.70MHz±30kHz
10.700MHz±25kHz
C
10.73MHz±30kHz
10.725MHz±25kHz
E
10.76MHz±30kHz
10.750MHz±25kHz
Z
Combination A,B,C,D,E
M
Combination A,B,C
13
45
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
■ CDALA10M7GA001-B0
Test Circuit
Frequency Characteristics
500
AFC
REF
–
10
AF OUTPUT
28
CDALA10M7GA001
S.S.G.
+
100k
Fg=50
CX20029
9
100
1µ
32
39
Vcc=+3.0V
Unit
R:Ω
C:F
AF Output
10
1
Distortion (%)
33
0.01µ
Recovered AF Output Voltage (mV)
5
280
Distortion
1
0.1
Input signal conditions
Input Level
Mod. Freq.
Freq.Dev.
10.4
10.5
10.6
10.7
10.8
Frequency (MHz)
10.9
110dBµ
400Hz
±22.5kHz
11.0
■ CDALA10M7GA016-B0
Test Circuit
Frequency Characteristics
500
DC Out AF Out
2.5µ
330p
1k
100
10
TA8122F (TOSHIBA)
3
4
5
6
+
7
8
9 10 11 12
0.022µ
2
22µ
1
CDACV10M7GA016
SFELA10M7DF00
Unit
R:Ω
C:F
270
0.022µ
IF in
Recovered AF Output Voltage (mV)
24 23 22 21 20 19 18 17 16 15 14 13
AF Output
10
1
Distortion
1
Distortion (%)
24k
0.033µ
+
0.1µ
VCC +3V
0.1
Input signal conditions
Input Level
Mod. Freq.
Freq.Dev.
10.4
10.5
10.6
10.7
10.8
Frequency (MHz)
10.9
80dBµ
1000Hz
±22.5kHz
11.0
■ CDALA10M7GA018-B0
Test Circuit
CDALA10M7GA018
1k
1000
0.022µ
330p
TA8132N (TOSHIBA)
2
3
4
5
6
7
8
9 10 11 12
22µ
+
0.022µ
Unit
R:Ω
C:F
Recovered AF Output Voltage ( mV )
0.033µ
24 23 22 21 20 19 18 17 16 15 14 13
1
100
+
0.1µ
270
SFELA10M7DF00
13
Frequency Characteristics
DC out
AF out
2.2µ
10
AF Output
100
10
1
Distortion
Distortion (%)
Vcc 3V
24k
1F in
Vcc 3V
1
0.1
Input signal conditions
Input Level 80 dBµ
Mod. Freq. 1000 Hz
Freq. Dev. ±22.5 kHz
10.4
10.5
10.6 10.7 10.8 10.9
Frequency ( MHz )
11.0
Continued on the following page.
46
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Continued from the preceding page.
■ CDALA10M7GA046-B0
Test Circuit
Frequency Characteristics
AF OUT
CSBLA456KE2ZF15 0.01µ
24
23
22
21
20
19
18
LA1832
6.8k
1
2
3
4
5
17
16
15
14
6
7
8
9
10
11
12
270
3k
2.2µ
CDALA10M7GA046
75
IF-IN
+
10µ
1µ
13
(SANYO)
300
0.047µ
AF Output
0.01µ
+
1µ
0.047µ
+
REG
100µ
Unit
R:Ω
C:F
10
100
Distortion
10
1
1
0.1
Distortion ( % )
1200p
+ 22µ
0.047µ
+
1µ
+
3.3µ
Recovered AF Output Voltage ( mV )
5.6k
AFC
100
1000
Vcc (5V)
Input signal conditions
Input Level 112 dBµ
Mod. Freq. 1000 Hz
Freq. Dev. ±75 kHz
10.4
10.5
10.6
10.7
10.8
Frequency ( MHz )
10.9
11.0
■ CDALA10M7GA048-B0
Test Circuit
Frequency Characteristics
Vt
500
CSBLA456KE2ZF15
33n
3.3µ
+
L. P. F.
30
29
28
27
26
1
2
3
4
5
25
24
23
22
21
AF Output
Rch
Lch
10µ 10µ
+ +
+
1µ
15k 5k
20
19
18
17
16
11
12
13
14
15
100
LA1835 (SANYO)
+
0.047µ
0.047µ
75
6
7
8
9
1µ
1k 1k
IF-IN
47n
10
10µ
510
300
20k
3k
+ 10µ + + 0.47µ
Unit
R:Ω
C:F
CDALA10M7GA048
10µ
VCC(7V)
REG.
10
10
1
Distortion
1
Distortion (%)
AFC
47n
L. P. F.
33n
Recovered AF Output Voltage (mV)
1500p
0.1
Input signal conditions
Input Level
Mod. Freq.
Freq.Dev.
10.4
10.5
10.6
10.7
10.8
Frequency (MHz)
10.9
112dBµ
1000Hz
±75kHz
11.0
■ CDALA10M7GA092-B0
Test Circuit
Frequency Characteristics
DC OUT
2.2µ
2
13
12
11
10
9
7
8
Vcc(3.0V)
4.7µ
TA2132P(TOSHIBA)
4
5
6
270 0.01µ
+
4.7µ
3
IF-IN
10
100
Unit
R:Ω
C:F
13
AF Output
10
1
Distortion
Distortion (%)
1
14
+
Recovered AF Output Voltage (mV)
15
CDALA10M7GZ092-B0
0.033µ
20k
330p
16
500
AF OUT
+
0.1
1
Input signal conditions
10.4
10.5
10.6
10.7
10.8
Frequency (MHz)
10.9
11.0
Input Level
80dBµ
Mod.Freq.
1000Hz
Freq.Dev.
±22.5kHz
Continued on the following page.
47
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Continued from the preceding page.
■ CDALA10M7CA001-B0
Test Circuit
VCC 5V
AF Output
Frequency Characteristics
AFC
1000
IF in
100
+
CX20090
100
4
+
5
6
(SONY)
7
8
9
10
11 12 13 14
1k
3
10µ
2
CDALA10M7CA001
1
18 17 16 15
Unit
R:Ω
C:F
Ref.
100
10
AF Output
Distortion ( % )
+
28 27 26 25 24 23 22 21 20 19
Recovered AF Output Voltage ( mV )
+
+
0.01µ
+
10µ
4.7µ
0.1µ
10µ
100µ
33µ
0.01µ
1
10
Distortion
0.1
1
Input signal conditions
Input Level 110 dBµ
Mod. Freq. 400 Hz
Freq. Dev. ±22.5 kHz
10.4
10.5
10.6
10.7
10.8
Frequency ( MHz )
10.9
11.0
■ CDALA10M7CA005A-B0
Test Circuit
Frequency Characteristics
1
2
18
17
16
15
14
13
12
11
9
10
IC : LA7770 (SANYO)
3
4
5
6
7
8
5p
0.01µ
0.01µ
0.01µ
+
-
0.01µ
33µ
1000p
Vcc=12V
0.022p
50
IF IN
Unit
R:Ω
C:F
Recovered AF Output Voltage ( mV )
19
AF Output
100
1000
Distortion
100
10
Distortion ( % )
470p
0.1µ
2k
220p
20
500
Demod.OUT
10k
CDALA10M7CA005A
2k
10k
20k
10k
5.6k
0.01µ
0.1µ
DC Bias
+5.2V
DC Bias
+5V
DATA OUT
470p
5000
1
10
Input signal conditions
Input Level 100 dBµ
Mod. Freq. 1000 Hz
Freq. Dev. ±75 kHz
10.6
10.7
10.8
Frequency ( MHz )
■ CDALA10M7CA040-B0
Test Circuit
Frequency Characteristics
VCC (3V)
+
+
0.01µ
+
1µ
DC-OUT
13
24
23
22
21
20
19
18
TEA5710
1
2
3
4
5
0.22µ
6
17
16
15
14
13
10
11
12
(PHILIPS)
7
8
9
0.01µ
280
0.22µ
50
S.S.G.
Unit
R:Ω
C:F
100
10
AF Output
Distortion
10
1
1
0.1
Distortion (%)
+
100
AF-OUT
100µ
10µ
Recovered AF Output Voltage ( mV )
0.01µ
100µ
1000
Input signal conditions
Input Level 100 dBµ
Mod. Freq. 1000 Hz
Freq. Dev. ±22.5 kHz
10.4
10.5
10.6
10.7
10.8
Frequency ( MHz )
48
10.9
11.0
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Lead Type Discriminators Notice
■ Notice (Soldering and Mounting)
The component cannot be withstand washing.
■ Notice (Handling)
1. Do not use this product with bend. The component
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
2. The component may be damaged when an excess stress
will be applied.
3. All kinds of re-flow soldering must not be applied
on the component.
4. Do not clean or wash the component as it is not
hermetically sealed.
5. Do not use strong acidity flux, more than 0.2wt%
chlorine content, in flow soldering.
6. In case of covering discriminator with over coat,
conditions such as material of resin, cure
temperature, and so on should be evaluated well.
7. Accurate test circuit values are required to
measure electrical characteristics. It may be a
cause of mis-correlation if there is any deviation,
especially stray capacitance, from the test
circuit in the specification.
13
49
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Packaging
■ Minimum Quantity
Ammo Pack
Bulk
SFELA
1,500
500
SFELB
1,500
500
SFVLA
1,000
500
SFKLA
1,500
500
Part Number
Taping ø180mm
SFECV
2,000
SFECS
2,000
SFTLA
500
CDACV / CDSCA
2,000
CDALA
500
1,500
■ Chip Type CERAFILr
■ Small Chip Type CERAFILr
40T0.15
10 pitch accumulated
4.0T0.1
5.5T0.05
∗∗
3.0T0.1
Peeling strength
0.1~0.7N
Part number marked side is always facing upside.
The feeding holes side of cavity tape is always input terminal.
1.9T0.1
10 max.
W0.1
3 max.
Cover Tape
1.7 Y0.05
0.3T0.05
Chip Filter
4.0T0.1
Peeling strengh (0.1Y0.7N)
3.35T0.1
4.0T0.1
Part number marked side is always facing upside.
User Direction of Feed
10˚
12.0±0.2
1.75±0.1
5.5±0.05
+0.1
-0
Ø1.5
2.2±0.1
The cover film peel
strength force 0.1~0.7N
Cover Film
Part Number marked side is always facing upside
3˚max.
Direction of Feed
(1.85max.)
1.9T0.1
.
W0.1
ax
0.3T0.05
10 max.
3m
4.0±0.1
1.7 Y0.05
Cover Tape
4.7±0.1
(9.5)
3.0T0.1
4.0T0.1
Peeling strengh (0.1Y0.7N)
+0.1
-0
Ø1.5
2.0±0.05
12.0T0.2
5.5T0.5
4.0T0.1
4.0±0.1
1.25±0.05
1.75T0.1
CDSCA Series
0.3T0.01
3.8T0.1
2.0T0.05
3.45
■ Chip Type Low-Profile Type Discriminator
CDACV Series
W0.1
3˚max.
10˚ max.
Cover film
User direction of feed
· Part Number marked side is always facing upside.
· The feeding holes side of cavity tape is always input terminal.
(in mm)
User Direction of Feed
■ Chip Type Discriminator
φ1.5 Y0.0
12.0T0.2
∗
∗∗
4.3
∗
∗∗
0.05
∗
∗∗
Chip Filter
12.0 +0.08
-0.2
∗
∗∗
7.3T0.01
∗
5.5T0.05
φ1.55T0.05 2.0T0.05
2.02T0.1
4.0T0.1
0.3T0.05
2.0T0.05
0.3±0.05
W0.1
φ1.5 Y0.0
SFECS Series
1.75T0.1
SFECV Series
(in mm)
Continued on the following page.
13
50
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Packaging
Continued from the preceding page.
■ Lead Type CERAFILr SF_LA Series
P2
∆h ∆h
P
H0
W1
W0
W
L2
L1
W2
∆S1
F1 F1
P1
D0
F
t
P0
Code
Dimensions
Lead Length under the Hold Down Tape
Item
L1
3.0 min.
Tolerance
Length of Cat off
L2
2.0 max.
Pitch of Components
P
12.7
±0.5
Pitch of Sprocket Hole (1)
P0
12.7
±0.2
To distinguish the direction
Length from Hole Center to Lead
P1
3.85
±0.5
Length from Hole Center to Component Center
P2
6.35
Pitch of the Terminal (1)
F
5.0
Pitch of the Terminal (2)
F1
2.5
±0.5
+0.5
–0.2
±0.2
Slant to the Forward or Backward
∆h
0
±1.0
Slant to the Left or Right
∆S1
0
±1.0
Width of Carrier Tape
W
18.0
±0.5
Width of Hold Down Tape
W0
6.0 min.
Position of Sprocket Hole
W1
9.0
Gap of Hold Down Tape and Carrier Tape
W2
0
±0.5
+0.5
–0
Distance Between the Center of Sprocket
Hole and Lead Stpper
H0
18.0
±0.5
Diameter of Sprocket Hole
D0
ø4.0
±0.2
t
0.6
±0.2
P020
254.0
±1.5
Total Tape Thickness
Pitch of Sprocket Hole (2)
Remarks
Must not protrude to the carrier tape
The pitch of 20 sprocket holes
(in mm)
Continued on the following page.
13
51
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Packaging
Continued from the preceding page.
■ Lead Type Discriminator CDALA Series
P2
∆h ∆h
P
H0
W1
W0
W
L1
W2
∆S1
D0
P1
F
t
P0
Item
Lead length under the hole down tape
Code
Dimensions
Tolerance
L1
3.0 min.
———
Pitch of component
P
12.7
±0.5
Pitch of sprocket hole (1)
P0
12.7
±0.2
Length from hole center to lead
P1
3.85
±0.5
Length from hole center to component center
P2
6.35
±0.5
Lead spacing
F
5.0
+0.5
-0.2
Slant to the forward or backward
∆h
0
±1.0
Slant to the left or right
∆S1
0
±1.0
W
18.0
±0.5
Width of hold down tape
W0
6.0 min.
———
Position of sprocket hole
W1
9.0
±0.5
Gap of hold down tape and
Carrier tape
W2
0
+0.5
-0.0
Distance between the center of
sprocket hole and lead stopper
H0
18.0
±0.5
Diameter of sprocket hole
D0
ø4.0
±0.2
t
0.6
±0.2
Po20
254.0
±1.5
Width of carrier tape
Total tape thickness
Pitch of sprocket hole (2)
Remarks
Hold down tape doesn't exceed the carrier tape
The pitch of 20 sprocket holes
(in mm)
13
52
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Test Circuit of Ceramic Discriminator
IC Manufacturer
IC
IC Manufacturer
IC
Sony
CX20029
CDALA10M7GF062
Toko
TK14581
CDALA10M7GA002
Sony
CX20076
CDALA10M7GA063
Samsung
KA2292
CDALA10M7GA004
Rohm
BA4234L
CDALA10M7GA064
Samsung
KA2295
CDALA10M7GA005
Rohm
BA4230AF
CDALA10M7GA065
Samsung
KA2298
CDALA10M7GA006
Toshiba
TA7640AP
CDALA10M7GA066
Rohm
BA4110
CDALA10M7GA007
Sanyo
LA1260
CDALA10M7GA067
Rohm
BA4240L
CDALA10M7GA008
Toshiba
TA7303P
CDALA10M7GA068
Sony
CXA1991N
CDALA10M7GA009
Toshiba
TA7130P
CDALA10M7GA069
Sony
CXA1538M/N/S
CDALA10M7GA011
Panasonic
AN7004
CDALA10M7GA070
Sanyo
LA1150
CDALA10M7GA012
Sony
CXA1030P
CDALA10M7GA071
Toshiba
TA7765
CDALA10M7GA013
Panasonic
AN7007SU
CDALA10M7GF072
Toshiba
TA31161
CDALA10M7GA014A
Panasonic
AN7006S
CDALA10M7GA073
Motorola
MC13158
Part Number
CDALA10M7GA001
Part Number
CDALA10M7GA015
Sanyo
LA1816
CDALA10M7GA075
Sony
CXA1611
CDALA10M7GA016
Toshiba
TA8122AN/F
CDALA10M7GA076
Sony
CXA3067M
CDALA10M7GA017
Philips
TEA5591
CDALA10M7GA077
Toshiba
TA2111
CDALA10M7GA018
Toshiba
TA8132AN/AF
CDALA10M7GA078
Sony
CX1691M
CDALA10M7GA019
Rohm
BA1440
CDALA10M7GA079
Sanyo
LA1838/M
CDALA10M7GA020
Philips
NE604
CDALA10M7GA080
Toshiba
TA2104AFN
CDALA10M7GF021A
Philips
TBA229-2
Toshiba
TA2104F
CDALA10M7GA022
Sanyo
LA1810
CDALA10M7GA081
Telefunken
U4313B
CDALA10M7GA023
Sanyo
LA7770
CDALA10M7GA082
Toshiba
TA2099N
CDALA10M7GF024
Philips
TDA2557
CDALA10M7GA083
Sanyo
LA1827
CDALA10M7GA025
Telefunken
U829B
CDALA10M7GA084
Rohm
BH4126FV
CDALA10M7GA026
Sanyo
LA1805
CDALA10M7GA085
Philips
SA639
CDALA10M7GA027
Sony
CXA1238
CDALA10M7GA086
Sanyo
LA1833
CDALA10M7GA027N
CDALA10M7GA080A
Sony
CXA1238N
CDALA10M7GA087
Motorola
MC3363
CDALA10M7GA028
Telefunken
U2501B
CDALA10M7GA088
Toshiba
TA8721ASN
CDALA10M7GA029
Philips
TBA120U
CDALA10M7GA089
Samsung
KA22425
CDALA10M7GA030
Philips
TEA5592
CDALA10M7GA090
Samsung
KA22901
CDALA10M7GA031
Toshiba
TA2003
CDALA10M7GA091
Samsung
KA2297
CDALA10M7GA032
Sony
CXA1343M
CDALA10M7GA092
Toshiba
TA2132
CDALA10M7GA033
Toshiba
TA2007N
CDALA10M7GA092D
Toshiba
TA2132BP
CXA1111
CDALA10M7GA034V
Telefunken
U4490B
CDALA10M7GA093
Sony
CDALA10M7GA035
Philips
TEA5594
CDALA10M7GA094
Sanyo
LA1822
CDALA10M7GA036
Toshiba
TA2029
CDALA10M7GA095
Temic
U2765B
CDALA10M7GA037
Sanyo
LA1830
CDALA10M7GA096
Philips
SA636DK
CDALA10M7GA038
Siemens
TDA6160X
CDALA10M7GA097
Matsushita
AN6138SH
CDALA10M7GA039
Toshiba
TA8186
CDALA10M7GA098
Philips
CAA3220TS
CDALA10M7GA040
Philips
TEA5710
CDALA10M7GA100
Toshiba
TA2149N
CDALA10M7GA041
Rohm
BA4220
CDALA10M7GA100A
Toshiba
TA2149AN
CDALA10M7GA042
Philips
SA605
CDALA10M7GA101
Sanyo
LA1823
CDALA10M7GA043
Sanyo
LA1831
CDALA10M7GA102
Toshiba
TA2142FN
CDALA10M7GA044
Siemens
TDA6160-2X
CDALA10M7GA103
Samsung
KB22902
CDALA10M7GA045
Toshiba
TA2008A/AN
CDALA10M7GA104
Rfmd
RF2925
CDALA10M7GA046
Sanyo
LA1832/M
CDALA10M7GA105A
Philips
TEA5757HL
CDALA10M7GA047
Philips
SA626
CDALA10M7GA106
Fujitsu
MB15G611
CDALA10M7GA048
Sanyo
LA1835/M
CDALA10M7GF107
Toshiba
TA31272FN
CDALA10M7GA049
Motorola
MC13156
CDALA10M7GF108A
Sanyo
LA1225M
CDALA10M7GA050
Toshiba
TA2022
CDALA10M7GF109
Toko
TK14588
CDALA10M7GA051
Siemens
TDA1576T
CDALA10M7GA110
Dspg
DS9RF21
CDALA10M7GA052
Motorola
MC13173
CDALA10M7GA053
Panasonic
AN7232
CDALA10M7GA054
Sony
CXA1376AM
CDALA10M7CA001
CDALA10M7GA055
Philips
TEA5712T
CDALA10M7GA056
NEC
µPC1391M
CDALA10M7GA057
Toshiba
CDALA10M7GA058
IC Manufacturer
IC
Sony
CX20091
CDALA10M7CA002
Toshiba
TA7687P/F
CDALA10M7CA004A
Motorola
MC3356P
TA2057
CDALA10M7CA005A
Sanyo
LA7770
Toshiba
TA2046
CDALA10M7CA006
Philips
TEA5591
CDALA10M7GA059
Samsung
KA2244
CDALA10M7CA009
Toshiba
TA7640AP
CDALA10M7GA060
Rohm
BA1448
CDALA10M7CA040
Philips
TEA5710
CDALA10M7GA061
Philips
TEA5762/5757
Part Number
53
13
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Example of Appllied Circuit
■ LA1140(Automotive Radio)
L1 2.2µH
AGC
R7 200
C3
0.047
C7
0.047
VR1
150k
C8
0.047
L2
SFELA10M7HAA0-B0
R4
10k
R6 SFELA10M7HAA0-B0
330
C.F.
16
12
9
11
R13
12k
13
1
C1
0.022
0.047
C6
R8
330
FRONT
END
R2
C.F.
1.8k
R3
C2
0.022
C4
1.8k
R2
1k
C5
AFC
7
+
C9 0.047
C10 4.7µ
LA1140
(SANYO)
2
+
8
3
4
5
6
14
22k
0.047 x 2
R9
220k
R10
2.2µ
C14
0.047
15
+
C11
33p
10
R12
R1
100
Vref.
R14
C13
33p
R2
47k
C15
■ CXA1019M(Radio)
FM PF
FM OSC
CERAMIC DISCRIMINATOR
FM CERAFIL®
(SFELA10M7FA00-B0) (CDALA10M7CA001-B0)
W
R
8
FM
BPF
AM ANT
12
IF
FM IF
OUT
IN
6 14 17
7
FM
FRONT
END
FM/AM
BAND SELECT
W
2
FM DISCRI
FM IF
AMP
DETECTOR
19
METER
25
26
Vcc
RIPPLE
FILTER
TUNING
METER
13
REGULATOR
8
REG
OUT
W
28
13
1
CXA1019M(SONY)
10
11
AM
FRONT
END
5
18
AM IF
AMP
DETECTOR
AM IF
IN
20 16
22
AM OSC
W
AF
PRE/POWER
AMP
VOL
23
DEP
OUT
21
W
4
24
AF IN
27
W
SP
3
W
W
AM CERAFIL®
(SFULA455KU2B-B0)
VOL
No adjustment is needed the FM detection stage due to use the ceramic discriminator.
Continued on the following page.
13
54
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Example of Appllied Circuit
Continued from the preceding page.
■ TA8122F(Radio)
CSBLA456KE2ZF16-B0
23
FM
OSC
22
2
20
19
FM
OSC
AM
OSC
AF
3
PRE
FM
DET
AM
AGC
AM
MIX
4
5
AM
AGC
W
BPF
AM
IF IN
LPF2
VCO
16
15
Phase
COM
Phase
COM
VCO
FM
IF IN
FM
IF
8
FM
DET
9
GND2
TUN
LED
10
TUN
LED
0.022µ
L
0.015µ
14
OUT
R
R
4.7µ
13
HYX
TA8122F(TOSHIBA)
SW
ST
LED
11
12
ST
LED QUAD
0.033µ
560
SFULA455KU2B-B0
4.7µ
W
W
ST
DECODER
Freq
Divider
T2
10µH
OUT
L
17
L
DET
7
0.015µ
AM
AM/FM
MONO SW
AM
IF
6
Vcc2
0.1µ
LPF1
18
33µ
FM
MIX
MPX
IN
21
AM
MIX
FM
RF
GND1
DEF
OUT
AM
MIX
AM
RF
1
AM
OSC
W
SFELA10M7FA00-B0
W
CDALA
10M7GA16-B0
22µ
OUT Vcc1
24
FM
RF IN
W
W
FM
560
AM
PF IN
FM
PF
MO
0.068µ
10µF
15p
ST
22k
T1
0.1µ
L2
100k
8p
0.022µF
33k
5p
22p
L1
20p
L3
100k
330p
IS2236
Vcc
(3V)
Detection and MPX stage adjustment ceramic discriminator and ceramic resonator (CERALOCK®)
13
55
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Note:
1. Export Control
For customers outside Japan
Murata products should not be used or sold for use in the development, production, stockpiling or utilization of any conventional weapons or mass-destructive
weapons (nuclear weapons, chemical or biological weapons, or missiles), or any other weapons.
For customers in Japan
For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is required
for export.
<
<
>
>
2. Please contact our sales representatives or product engineers before using our products listed in this catalog for the applications listed below which require
especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property, or when intending to use one
of our products for other applications than specified in this catalog.
q Aircraft equipment
w Aerospace equipment
e Undersea equipment
r Power plant equipment
t Medical equipment
y Transportation equipment (vehicles, trains, ships, etc.)
u Traffic signal equipment
i Disaster prevention / crime prevention equipment
o Data-processing equipment
!0 Application of similar complexity and/or reliability requirements to the applications listed in the above
3. Product specifications in this catalog are as of May 2001. They are subject to change or our products in it may be discontinued without advance notice. Please
check with our sales representatives or product engineers before your ordering. If there are any questions, please contact our sales representatives or product
engineers.
4. Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our product
specification or to transact the approval sheet for product specification, before your ordering.
5. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect
of our and/or third party's intellectual property rights and other related rights in consideration of your using our products and/or information described or
contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned
above under licenses without our consent.
6. None of ozone depleting substances (ODS) under the Montreal Protocol is used in manufacturing process of us.
http://www.murata.co.jp/products/
Head Office
2-26-10, Tenjin Nagaokakyo-shi, Kyoto 617-8555, Japan Phone:81-75-951-9111
International Division
3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan
Phone:81-3-5469-6123 Fax:81-3-5469-6155 E-mail:[email protected]