Pan Jit DI150 Dual-in-line glass passivated single-phase bridge rectifier(voltage - 50 to 1000 volts current - 1.0~1.5 amperes) Datasheet

DI100/150 THRU DI1010/1510
DUAL-IN-LINE GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 1000 Volts CURRENT - 1.0~1.5 Amperes
DIP
Recongnized File #E111753
l Low leakage
l Surge overload rating— 30~50 amperes peak
.255 (6.5)
.245 (6.2)
.315 (8.00)
.285 (7.24)
l Plastic material used carries Underwriters Laboratory
recognition 94V-O
.350(8.9)
.300(7.6)
.335 (8.51)
.316 (8.05)
FEATURES
l Exceeds environmental standards of MIL-S-19500/228
.120(3.05)
.130(3.30)
l Ideal for printed circuit board
.045 (1.14)
.035 (0.89)
MECHANICAL DATA
.022 (0.56)
.018 (0.46)
.185 (4.69)
.150 (3.81)
Case: Reliable low cost construction utilizing molded plastic
technique results in inexpensive product
Terminals: Lead solderable per MIL-STD-202, Method 208
Polarity: Polarity symbols molded or marking on body
.205 (5.2)
.195 (5.0)
.075 (1.90)
.055 (1.39)
Mounting Position: Any
Weight: 0.02 ounce, 0.4 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 OC ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, Resistive or inductive load.
For capacitive load, derate current by 20%.
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Bridge input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Current
T A=40 OC
DI100
DI150
50
35
50
DI100
DI150
DI100
DI150
Peak Forward Surge Current, 8.3ms single
half sine-wave superimposed on rated load
I2t Rating for fusing ( t < 8.35 ms)
Maximum Forward Voltage Drop per Bridge Element at 1.0A
Maximum Reverse Current at Rated TJ= 25OC
DC Blocking Voltage per element TJ=125 OC
Typical Junction capacitance per leg (Note 1) CJ
Typical Thermal resistance per leg (Note 2) RθJA
Typical Thermal resistance per leg (Note 2) RθJL
Operating Temperature Range TJ
Storage Temperature Range TA
DI101
DI151
100
70
100
DI102
DI152
200
140
200
DI104
DI154
400
280
400
1.0
1.5
30.0
50.0
10.0
1.1
5.0
0.5
25.0
40.0
15.0
-55 to +125
-55 to +150
DI106
DI156
600
420
600
DI108
DI158
800
560
800
DI1010
UNITS
DI1510
1000
V
700
V
1000
V
A
NOTES:
1.
Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
2.
Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.5x0.5”(13 x 13mm) copper pads
A
A2t
V
µA
mA
PF
OC /W
C
C
O
O
RATING AND CHARACTERISTIC CURVES
40
DI150
30
20
DI100
10
1
2
4
6
8 10
20
40 60 80 100
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
1.50
1.00
AMPERES
50
AVERAGE FORWARD OUTPUT CURRENT,
AMPERES pk (HALF-SINE WAVE)
FORWARD SURGE CURRENT,
DI100/150 THRU DI1010/1510
DI150
0.75
DI100
0.50
0
20
40
60
80
100
120
140
AMBIENT TEMPERATURE, ℃
Fig. 1-MAXIMUM NON-REPETITIVE SURGE CURRENT
Fig. 2-DERATING CURVE FOR OUTPUT RECTIFIED
CURRENT
0.1
TJ = 25 ℃
PULSE WIDTH =
200uS
.01
.4
.6
8
1.0
1.2
1.4
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
Fig. 3-TYPICAL FORWARD CHARACTERISTICS
CURRENT, MICROAMPERES
1.0
INSTANTANEOUS REVERSE
CURRENT, AMPERES
INSTANTANEOUS FORWARD
10
10
TA = 100 ℃
1.0
TA = 25 ℃
.1
.01
0
20
40
60
80
100
120
140
PERCENT OF PEAK REVERSE VOLTAGE
Fig. 4-TYPICAL REVERSE CHARACTERISTICS
Similar pages