TI1 ADS8509IBDB 16-bit 250-ksps serial cmos sampling analog-to-digital converter Datasheet

ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
16-BIT 250-KSPS SERIAL CMOS SAMPLING ANALOG-TO-DIGITAL CONVERTER
Check for Samples: ADS8509
FEATURES
DESCRIPTION
•
•
The ADS8509 is a complete 16-bit sampling
analog-to-digital (A/D) converter using state-of-the-art
CMOS structures. It contains a complete 16-bit,
capacitor-based, successive approximation register
(SAR) A/D converter with sample-and-hold,
reference, clock, and a serial data interface. Data can
be output using the internal clock or can be
synchronized to an external data clock. The ADS8509
also provides an output synchronization pulse for
ease of use with standard DSP processors.
1
2
•
•
•
•
•
•
•
•
•
250-kHz Sampling Rate
4-V, 5-V, 10-V, ±3.33-V, ±5-V, and ±10-V Input
Ranges
±2 LSB Max INL
±1 LSB Max DNL, 16-Bit No Missing Codes
SPI Compatible Serial Output with Daisy-Chain
(TAG) Feature
Single 5-V Supply
Pin-Compatible with ADS7809 (Low Speed)
and 12-Bit ADS8508/7808
Uses Internal or External Reference
70-mW Typ Power Dissipation at 250 KSPS
20-Pin SO and 28-Pin SSOP Packages
Simple DSP Interface
The ADS8509 is available in 20-pin SO and 28-pin
SSOP packages, both fully specified for operation
over the industrial -40°C to 85°C temperature range.
APPLICATIONS
•
•
•
•
•
The ADS8509 is specified at a 250-kHz sampling rate
over the full temperature range. Precision resistors
provide various input ranges including ±10 V and 0 V
to 5 V, while the innovative design allows operation
from a single +5-V supply with power dissipation
under 100 mW.
Industrial Process Control
Data Acquisition Systems
Digital Signal Processing
Medical Equipment
Instrumentation
Successive Approximation Register
Clock
CDAC
9.8 kΩ
R1IN
BUSY
4.9 kΩ
R2IN
2.5 kΩ
R3IN
EXT/INT
10 kΩ
Comparator
CAP
Buffer
Internal
+2.5 V Ref
Serial
Data
Out
&
Control
DATACLK
DATA
R/C
SB/BTC
CS
PWRD
4 kΩ
REF
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2010, Texas Instruments Incorporated
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION (1)
PRODUCT
MINIMUM
RELATIVE
ACCURACY
(LSB)
ADS8509IB
NO
MISSING
CODE
±2
16
MINIMUM
SINAD
(dB)
85
SPECIFICATION
TEMPERATURE
RANGE
PACKAGE
LEAD
PACKAGE
DESIGNATOR
SO-20
DW
–40°C to 85°C
SSOP-28
SO-20
ADS8509I
±3
15
83
SSOP-28
(1)
ADS8509IBDBR
DW
DB
ADS8509IBDW
ADS8509IBDWR
ADS8509IBDB
DB
–40°C to 85°C
ORDERING
NUMBER
ADS8509IDW
ADS8509IDWR
ADS8509IDB
ADS8509IDBR
TRANSPORT
MEDIA, QTY
Tube, 25
Tape and Reel, 2000
Tube, 50
Tape and Reel, 2000
Tube, 25
Tape and Reel, 2000
Tube, 50
Tape and Reel, 2000
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or visit the
device product folder on www.ti.com.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted) (1)
UNIT
Analog inputs
R1IN
±25 V
R2IN
±25 V
R3IN
±25 V
REF
+VANA + 0.3 V to AGND2 – 0.3 V
CAP
Indefinite short to AGND2, momentary short to VANA
DGND, AGND2
Ground voltage differences
±0.3 V
VANA
6V
VDIG to VANA
0.3 V
VDIG
6V
Digital inputs
–0.3 V to +VDIG + 0.3 V
Maximum junction temperature
165°C
Storage temperature range
–65°C to 150°C
Internal power dissipation
700 mW
Lead temperature (soldering, 1.6 mm from case 10 seconds)
(1)
260°C
All voltage values are with respect to network ground terminal.
2
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
ELECTRICAL CHARACTERISTICS
At TA = –40°C to 85°C, fs = 250 kHz, VDIG = VANA = 5 V, using internal reference and 0.1%, 0.25-W fixed resistors (see
Figure 29 and Figure 30) (unless otherwise specified)
PARAMETER
TEST CONDITIONS
ADS8509I
MIN
TYP
Resolution
ADS8509IB
MAX
MIN
TYP
16
MAX
16
UNIT
Bits
ANALOG INPUT
Voltage range (1)
Impedance (1)
Capacitance
50
50
pF
THROUGHPUT SPEED
Conversion cycle
Acquire and convert
Throughput rate
4
250
4
250
ms
kHz
DC ACCURACY
INL
Integral linearity error
–3
3
–2
2
LSB (2)
DNL
Differential linearity error
–2
2
–1
1
LSB
No missing codes
15
Transition noise (3)
Full-scale
error (4) (5)
±10-V Range
All other ranges
Full-scale error drift
Full-scale
error (4) (5)
±10-V Range
All other ranges
Full-scale error drift
1
Int. ref. with 0.1% external fixed
resistors
LSB
0.5
–0.5
0.5
–0.5
0.5
–0.5
0.5
–0.5
0.5
–0.5
0.5
–0.5
0.5
–0.5
0.5
10
–5
±7
Ext. ref. with 0.1% external
fixed resistors
Bits
1
–0.5
Int. ref.
Ext. ref.
±7
±2
Bipolar zero error (4)
–10
Bipolar zero error drift
Unipolar zero
error (4)
16
ppm/°C
±2
±0.4
±0.4
–5
5
–5
5
–3
3
–3
3
Power supply sensitivity
(VDIG = VANA = VD)
1-mF Capacitor to CAP
+4.75 V < VD < +5.25 V
mV
ppm/°C
4-V and 5-V
Range
Recovery to rated accuracy after
power down
%FSR
ppm/°C
5
10-V Range
Unipolar zero error drift
%FSR
mV
±2
±2
ppm/°C
1
1
ms
–8
8
–8
8
LSB
AC ACCURACY
SFDR
Spurious-free dynamic range
fI = 20 kHz
THD
Total harmonic distortion
fI = 20 kHz
SINAD
SNR
Signal-to-(noise+distortion)
Signal-to-noise ratio
fI = 20 kHz
90
–98
83
–60-dB Input
fI = 20 kHz
Full-power bandwidth (7)
99
95
–90
88
–98
85
30
83
88
86
500
dB (6)
99
–93
dB
88
dB
32
dB
88
dB
500
kHz
SAMPLING DYNAMICS
Aperture delay
Transient response
5
FS Step
Overvoltage recovery (8)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
5
2
150
ns
2
150
ms
ns
±10 V, 0 V to 5 V, etc. (see Table 2). For normal operation, the analog input should not exceed configured range ±20%.
LSB means least significant bit. For the ±10-V input range, one LSB is 305 mV.
Typical rms noise at worst case transitions and temperatures.
As measured with fixed resistors shown in Figure 29 and Figure 30. Adjustable to zero with external potentiometer. Factory calibrated
with 0.1%, 0.25-W resistors.
For bipolar input ranges, full-scale error is the worst case of –full-scale or +full-scale uncalibrated deviation from ideal first and last code
transitions, divided by the transition voltage (not divided by the full-scale range) and includes the effect of offset error. For unipolar input
ranges, full-scale error is the deviation of the last code transition divided by the transition voltage. It also includes the effect of offset
error.
All specifications in dB are referred to a full-scale ±10-V input.
Full-power bandwidth is defined as the full-scale input frequency at which signal-to-(noise + distortion) degrades to 60 dB.
Recovers to specified performance after 2 x FS input overvoltage.
3
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
At TA = –40°C to 85°C, fs = 250 kHz, VDIG = VANA = 5 V, using internal reference and 0.1%, 0.25-W fixed resistors (see
Figure 29 and Figure 30) (unless otherwise specified)
PARAMETER
TEST CONDITIONS
ADS8509I
ADS8509IB
MIN
TYP
MAX
MIN
TYP
MAX
2.48
2.5
2.52
2.48
2.5
2.52
UNIT
REFERENCE
Internal reference voltage
No load
Internal reference source current
(must use external buffer)
1
Internal reference drift
8
External reference voltage range
for specified linearity
External reference current drain
2.3
2.5
Ext. 2.5-V ref.
V
1
mA
8
2.7
2.3
2.5
100
ppm/°C
2.7
V
100
mA
V
DIGITAL INPUTS
Logic levels
VIL
Low-level input voltage
–0.3
0.8
–0.3
0.8
VIH
High-level input voltage
2.0
VDIG +0.3 V
2.0
VDIG +0.3 V
V
IIL
Low-level input current
VIL = 0 V
±10
±10
mA
IIH
High-level input current
VIH = 5 V
±10
±10
mA
DIGITAL OUTPUTS
Data format (serial 16-bits)
Data coding (binary 2's
complement or straight binary)
Pipeline delay (conversion results
only available after completed
conversion)
Data clock (selectable for internal
or external data clock)
Internal clock (output only when
transmitting data)
EXT/INT Low
9
External clock (can run
continually but not recommended
for optimum performance)
EXT/INT High
VOL
Low-level output voltage
ISINK = 1.6 mA
VOH
High-level output voltage
ISOURCE = 500 mA
Leakage current
Hi-Z State,
VOUT = 0 V to VDIG
Output capacitance
Hi-Z State
0.1
9
26
0.1
MHz
26
MHz
0.4
0.4
V
±5
±5
mA
15
15
pF
V
4
4
V
POWER SUPPLIES
VDIG
Digital input voltage
4.75
5
5.25
4.75
5
5.25
VANA
Analog input voltage
4.75
5
5.25
4.75
5
5.25
IDIG
Digital input current
IANA
Analog input current
Must be ≤ VANA
V
4
4
mA
10
10
mA
POWER DISSIPATION
PWRD Low
fS = 250 kHz
70
PWRD High
100
70
50
100
50
mW
mW
TEMPERATURE RANGE
Specified performance
–40
85
–40
85
°C
Derated performance (9)
–55
125
–55
125
°C
Storage
–65
150
–65
150
°C
THERMAL RESISTANCE (qJA)
(9)
SSOP
62
62
°C/W
SO
46
46
°C/W
The internal reference may not be started correctly beyond the industrial temperature range (–40°C to 85°C), therefore use of an
external reference is recommended.
4
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
PIN CONFIGURATIONS
DW PACKAGE
SO-20
(TOP VIEW)
R1IN
1
20
VDIG
AGND1
2
19
VANA
R2IN
3
18
PWRD
R3IN
4
17
BUSY
CAP
5
16
CS
REF
6
15
R/C
AGND2
7
14
TAG
SB/BTC
8
13
DATA
EXT/INT
9
12
DATACLK
DGND
10
11 SYNC
DB PACKAGE
SSOP-28
(TOP VIEW)
R1IN
1
28
VDIG
AGND1
2
27
VANA
R2IN
3
26
PWRD
R3IN
4
25
BUSY
NC
5
24
CS
CAP
6
23
NC
REF
7
22
NC
NC
8
21
R/C
AGND2
9
20
NC
NC
10
19 TAG
NC
NC
11
18
SB/BTC
12
17
DATA
EXT/INT
13
16
DATACLK
DGND
14
15
SYNC
5
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
www.ti.com
Terminal Functions
TERMINAL
NAME
AGND1
DESCRIPTION
DB NO.
DW NO.
I/O
2
2
–
Analog ground. Used internally as ground reference point. Minimal current flow.
AGND2
9
7
–
Analog ground
BUSY
25
17
O
Busy output. Falls when a conversion is started and remains low until the conversion is completed
and the data is latched into the output shift register.
CAP
6
5
–
Reference buffer capacitor. 2.2-mF Tantalum to ground.
CS
24
16
–
Chip select. Internally ORed with R/C.
DATA
17
13
O
Serial data output. Data is synchronized to DATACLK with the format determined by the level of
SB/BTC. In the external clock mode, after 16 bits of data, the ADS8509 outputs the level input on
TAG as long as CS is low and R/C is high (see Figure 8 and Figure 9). If EXT/INT is low, data is
valid on both the rising and falling edges of DATACLK, and between conversions DATA stays at
the level of the TAG input when the conversion was started.
DATACLK
16
12
I/O
Either an input or an output depending on the EXT/INT level. Output data is synchronized to this
clock. If EXT/INT is low, DATACLK transmits 16 pulses after each conversion and then remains
low between conversions.
DGND
14
10
–
Digital ground
EXT/INT
13
9
–
Selects external or internal clock for transmitting data. If high, data is output synchronized to the
clock input on DATACLK. If low, a convert command initiates the transmission of the data from the
previous conversion, along with 16-clock pulses output on DATACLK.
5, 8, 10,
11, 18,
20, 22,
23
–
–
No connect
PWRD
26
18
I
Power down input. If high, conversions are inhibited and power consumption is significantly
reduced. Results from the previous conversion are maintained in the output shift register.
R/C
21
15
I
Read/convert input. With CS low, a falling edge on R/C puts the internal sample-and-hold into the
hold state and starts a conversion. When EXT/INT is low, this also initiates the transmission of the
data results from the previous conversion. If EXT/INT is high, a rising edge on R/C with CS low or
a falling edge on CS with R/C high transmits a pulse on SYNC and initiates the transmission of
data from the previous conversion.
REF
7
6
I/O
R1IN
1
1
I
Analog input. See Table 2 for input range connections.
R2IN
3
3
I
Analog input. See Table 2 for input range connections.
R3IN
4
4
I
Analog input. See Table 2 for input range connections.
SB/BTC
12
8
I
Select straight binary or binary 2's complement data output format. If high, data is output in a
straight binary format. If low, data is output in a binary 2's complement format.
SYNC
15
11
O
Sync output. This pin is used to supply a data synchronization pulse when the EXT level is high
and at least one external clock pulse has occurred when not in the read mode. See the external
clock modes desciptions.
TAG
19
14
I
Tag input for use in the external clock mode. If EXT is high, digital data input from TAG is output
on DATA with a delay that is dependent on the external clock mode. See Figure 8 and Figure 9.
VANA
27
19
I
Analog supply input. Nominally +5 V. Connect directly to pin 20 and decouple to ground with
0.1-mF ceramic and 10-mF tantalum capacitors.
VDIG
28
20
I
Digital supply input. Nominally +5 V. Connect directly to pin 19. Must be ≤ VANA.
NC
Reference input/output. Outputs internal 2.5-V reference. Can also be driven by external system
reference. In both cases, bypass to ground with a 2.2-mF tantalum capacitor.
6
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
TIMING REQUIREMENTS, TA = –40°C to 85°C
PARAMETER
MIN
TYP
MAX
6
20
ns
2.2
ms
Pulse duration, convert
td1
Delay time, BUSY from R/C low
tw2
Pulse duration, BUSY low
td2
Delay time, BUSY, after end of conversion
5
ns
td3
Delay time, aperture
5
ns
tconv
Conversion time
tacq
Acquisition time
tconv + tacq
40
UNIT
tw1
ns
2.2
1.8
ms
ms
Cycle time
4
ms
td4
Delay time, R/C low to internal DATACLK output
270
ns
tc1
Cycle time, internal DATACLK
110
ns
td5
Delay time, data valid to internal DATACLK high
15
35
ns
td6
Delay time, data valid after internal DATACLK low
20
35
ns
tc2
Cycle time, external DATACLK
35
ns
tw3
Pulse duration, external DATACLK high
15
ns
tw4
Pulse duration, external DATACLK low
15
ns
tsu1
Setup time, R/C rise/fall to external DATACLK high
15
ns
tsu2
Setup time, R/C transition to CS transition
10
td7
Delay time, SYNC, after external DATACLK high
td8
Delay time, data valid
td9
Delay time, CS to rising edge
td10
ns
3
35
ns
2
20
ns
10
ns
Delay time, previous data available after CS, R/C low
2
ms
tsu3
Setup time, BUSY transition to first external DATACLK
5
ns
td11
Delay time, final external DATACLK to BUSY falling edge
tsu3
Setup time, TAG valid
0
ns
th1
Hold time, TAG valid
2
ns
1
ms
PARAMETER MEASUREMENT INFORMATION
CS
R/C
R/C
CS
tsu1
tsu1
tsu1
External
DATACLK
tsu1
External
DATACLK
CS Set Low, Discontinuous Ext DATACLK
R/C Set Low, Discontinuous Ext DATACLK
BUSY
CS
tsu2
R/C
tsu2
tsu3
External
DATACLK
1
2
CS Set Low, Discontinuous Ext DATACLK
Figure 1. Critical Timing
7
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
tw1
tw1
R/C
td1
td1
tw2
tw2
BUSY
td2
td3
STATUS
Error
Correction
Nth Conversion
td2
td11
td3
td11
Error
(N+1)th Conversion Correction
(N+1)th Accquisition
tconv
tconv
tacq
tc1
td4
(N+2)th Accquisition
tacq
td4
Internal
1
DATACLK
2
16
16
td6
td5
DATA
2
1
D15
TAG = 0
TAG = 0
D0
D15
D0
TAG = 0
Nth Conversion Data
(N−1)th Conversion Data
CS, EXT/INT, and TAG are tied low
8 starts READ
Figure 2. Basic Conversion Timing (Internal DATACLK - Read Previous Data During Conversion)
tw1
tw1
R/C
td1
td1
tw2
tw2
BUSY
td2
td3
STATUS
Error
Correction
Nth Conversion
td2
td3
td11
td11
(N+1)th Accquisition
(N+1)th Conversion
tacq
tconv
(N+2)th Accquisition
tacq
tconv
tsu3
tsu1
Error
Correction
tsu3
tsu1
External
DATACLK
DATA TAG = 0
1
16
No more
data to
shift out
EXT/INT tied high, CS and TAG are tied low
1
TAG = 0
2
1
16
Nth Data
TAG = 0
16
1
No more
data to
shift out
TAG = 0
2
16
(N+1)th Data
TAG = 0
tw1 + tsu1 starts READ
Figure 3. Basic Conversion Timing (External DATACLK)
8
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
PARAMETER MEASUREMENT INFORMATION (continued)
tw1
R/C
td1
tsu1
tw2
td1
BUSY
td2
td3
td3
td11
STATUS
Nth Conversion
Error
Correction
(N+1) th Accquisition
tsu3
tconv
tacq
tc2
tw3
External
tsu1
tw4
DATACLK
0
1
2
3
4
5
10
11
12
14
13
15
16
SYNC = 0
td8
D14
D13
D12
D11
D10
D05
D04
D03
D02
D01
D00
Null
T00
Txx
T02
T03
T04
T05
T06
T11
T12
T13
T14
T15
T16
Null
T17
Tyy
th1
tsu3
TAG
td8
Nth Conversion Data
D15
DATA
T00
T01
EXT/INT tied high, CS tied low
tw1 + tsu1 starts READ
Figure 4. Read After Conversion (Discontinuous External DATACLK)
tw1
R/C
td1
tw2
BUSY
td10
td3
td2
Error
Correction
Nth Conversion
STATUS
tsu3
tconv
tc2
External
tsu1
tw3
1
0
DATACLK
td11
tw4
2
3
4
5
10
11
12
13
14
15
16
SYNC = 0
td8
Nth Conversion Data
D15
DATA
EXT/INT tied high, CS and TAG tied low
D14
D13
D12
D11
D10
D05
D04
D03
td8
D02
D01
D00
Rising DATACLK change DATA, tw1 + tsu1 Starts READ
TAG is not recommended for this mode. There is not enough
time to do so without violating td11.
Figure 5. Read During Conversion (Discontinuous External DATACLK)
9
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
tw1
R/C
td1
tsu1
td1
tsu1
tw2
BUSY
td2
td3
td3
td11
Error
Nth Conversion Correction
STATUS
(N+1)th Accquisition
tconv
tacq
tc2
tsu3
tsu1
External
0
DATACLK
tsu1
tw4
tw3
1
2
3
4
5
6
7
12
13
14
15
16
17
18
tc2
td7
SYNC =0
td8
Nth Conversion Data
D15
DATA
td8
D14
D13
D12
D11
D10
D05
D04
D03
D02
D01
D00
Null
T02
T03
T04
T05
T06
T11
T12
T13
T14
T15
T16
T17
T00
Txx
th1
tsu3
TAG
T00
T01
Tyy
tw1 + tsu1 starts READ
EXT/INT tied high, CS tied low
Figure 6. Read After Conversion With SYNC (Discontinuous External DATACLK)
tw1
R/C
td1
tw2
BUSY
td3
td10
td2
Error
Correction
Nth Conversion
STATUS
tsu3
tconv
tsu1
tsu1
External
tw3
tsu1
0
DATACLK
tc2
tw4
1
2
3
td11
4
5
6
7
12
13
14
15
16
17
18
td7
tc2
SYNC = 0
td8
DATA
EXT/INT tied high, CS and TAG tied low
td8
Nth Conversion Data
D15
D14
D13
D12
D11
D10
D05
D04
D03
D02
D01
D00
tw1 + tsu1 Starts READ
TAG is not recommended for this mode. There is not enough
time to do so without violating td11.
Figure 7. Read During Conversion With SYNC (Discontinuous External DATACLK)
10
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
Tag 18
Tag 17
Tag 16
Tag 15
Tag 1
TAG
Tag 2
Bit 15 (MSB)
DATA
Tag 0
t c2
t su2
t su1
0
SYNC
BUSY
R/C
CS
External
DATACLK
t w1
t su2
t d1
t w3
t d7
1
t c2
t w4
2
t d8
3
Bit 14
4
Bit 1
17
18
Bit 0 (LSB)
Tag 0
t d9
Tag 1
Tag 19
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 8. Conversion and Read Timing with Continuous External DATACLK (EXT/INT Tied High) Read
After Conversions (Not Recommended)
11
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
www.ti.com
Tag 18
Tag 17
Tag 1
TAG
Tag 16
Bit 15 (MSB)
DATA
SYNC
t d1
BUSY
R/C
CS
External
DATACLK
t su2
t w3
t c2
t w1
t w4
t su1
t su1
Tag 0
t c2
t d8
t d10
Bit 0 (LSB)
Tag 0
t d8
Tag 1
Tag 19
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 9. Conversion and Read Timing with Continous External DATACLK (EXT/INT Tied High) Read
Previous Conversion Results During Conversion (Not Recommended)
12
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION
vs
FREE-AIR TEMPERATURE
−100
105
THD − Total Harmonic Distortion − dB
SFDR − Spurious Free Dynamic Range − dB
SPURIOUS FREE DYNAMIC RANGE
vs
FREE-AIR TEMPERATURE
100
95
90
85
fs = 250 KSPS,
fi = 20 kHz
80
75
−40
25
−95
−90
−85
−80
fs = 250 KSPS,
fi = 20 kHz
−75
−70
−40
85
TA − Free-Air Temperature − 5C
Figure 11.
SIGNAL-TO-NOISE RATIO
vs
FREE-AIR TEMPERATURE
SIGNAL-TO-NOISE AND DISTORTION
vs
FREE-AIR TEMPERATURE
SINAD − Signal-To-Noise and Distortion − dB
SNR − Signal-to-Noise Ratio − dB
85
Figure 10.
100
fs = 250 KSPS,
fi = 20 kHz
95
90
85
80
75
70
−40
25
85
100
fs = 250 KSPS,
fi = 20 kHz
95
90
85
80
75
70
−40
TA − Free-Air Temperature − 5C
25
85
TA − Free-Air Temperature − 5C
Figure 12.
Figure 13.
SIGNAL-TO-NOISE RATIO
vs
INPUT FREQUENCY
SIGNAL-TO-NOISE AND DISTORTION
vs
INPUT FREQUENCY
SINAD − Signal-To-Noise and Distortion − dB
90
SNR − Signal-to-Noise Ratio − dB
25
TA − Free-Air Temperature − 5C
85
80
75
70
65
1
10
fi − Input Frequency − kHz
100
Figure 14.
90
85
80
75
70
65
1
10
fi − Input Frequency − kHz
100
Figure 15.
13
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
105
−105
100
95
90
85
80
75
−100
−95
−90
−85
−80
−75
−70
70
1
10
fi − Input Frequency − kHz
1
100
100
Figure 16.
Figure 17.
INTERNAL REFERENCE VOLTAGE
vs
FREE-AIR TEMPERATURE
BIPOLAR ZERO SCALE ERROR
vs
FREE-AIR TEMPERATURE
2.510
5
2.508
4
2.506
2.504
2.502
2.500
2.498
2.496
2.494
2.492
2
1
0
−1
−2
−3
25
45
65
85
−5
−40 −25 −10
105
TA − Free-Air Temperature − 5C
20
35
50
65
Figure 18.
Figure 19.
FULL SCALE ERROR
vs
FREE-AIR TEMPERATURE
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
80
20
External Reference,
±10 V Range
for 5 Representative
Parts
19
18
Supply Current − mA
0.10
5
TA − Free-Air Temperature − 5C
0.20
0.15
External Reference,
±10-V Range
3
−4
2.490
−55 −35 −15 5
Full Scale Error − %FSR
10
fi − Input Frequency − kHz
Bipolar Zero Scale Error − mV
Internal Reference Voltage − V
TOTAL HARMONIC DISTORTION
vs
INPUT FREQUENCY
THD − Total Harmonic Distortion − dB
SFDR − Spurious Free Dynamic Range − dB
SPURIOUS FREE DYNAMIC RANGE
vs
INPUT FREQUENCY
0.05
0
−0.05
−0.10
17
16
15
14
13
12
−0.15
11
−0.20
−40 −25 −10 5
20
35
50
65
80
TA − Free-Air Temperature − 5C
10
−40 −25 −10 5
20
35
50
65
80
TA − Free-Air Temperature − 5C
Figure 20.
Figure 21.
14
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
TYPICAL CHARACTERISTICS (continued)
PERFORMANCE
vs
CAP PIN CAPACITOR ESR
HISTOGRAM
8192
Conversions
of a DC Input
4000
3500
100
4224
95
|THD|
90
Performance
4500
Hits
3000
2500
2082
2000
1484
1500
80
75
70
65
1000
60
500
4
0
SINAD
85
−3
−2
−1
0
1
2
2.2 µF Capacitor on
CAP Pin (pin 6)
55
238
149
11
3
50
0
1
2
Code
Figure 22.
3 4 5 6 7 8 9
ESR − Resistance − W
10 11
Figure 23.
INTEGRAL NONLINEARITY
2.5
fs = 250 KSPS
2
1.5
INL − LSBs
1
0.5
0
−0.5
−1
−1.5
−2
−2.5
0
16384
32768
49152
65536
49152
65536
Code
Figure 24.
DIFFERENTIAL NONLINEARITY
2.5
fs = 250 KSPS
2
1.5
DNL − LSBs
1
0.5
0
−0.5
−1
−1.5
−2
−2.5
0
16384
32768
Code
Figure 25.
15
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
FFT (20-kHz Input)
20
8192 Points,
fs = 250 KSPS,
fi = 20 kHz, 0 dB
SINAD = 86.0 dB,
THD = −98.7 dB
0
−20
Amplitude − dB
−40
−60
−80
−100
−120
−140
−160
−180
0
25
50
75
100
125
f − Frequency − kHz
Figure 26.
BASIC OPERATION
Two signals control conversion in the ADS8509: CS and R/C. These two signals are internally ORed together. To
start a conversion the chip must be selected, CS low, and the conversion signal must be active, R/C low. Either
signal can be brought low first. Conversion starts on the falling edge of the second signal. BUSY goes low when
conversion starts and returns high after the data from that conversion is shifted into the internal storage register.
Sampling begins when BUSY goes high.
To reduce the number of control pins CS can be tied low permanently. The R/C pin now controls conversion and
data reading exclusively. In the external clock mode this means that the ADS8509 clocks out data whenever R/C
is brought high and the external clock is active. In the internal clock mode data is clocked out every convert cycle
regardless of the states of CS and R/C. The ADS8509 provides a TAG input for cascading multiple converters
together.
READING DATA
The conversion result is available as soon as BUSY returns to high, therefore data always represents the
conversion previously completed even when it is read during a conversion. The ADS8509 outputs serial data in
either straight binary or binary two’s compliment format. The SB/BTC pin controls the format. Data is shifted out
MSB first. The first conversion immediately following a power-up does not produce a valid conversion result.
Data can be clocked out with either the internally generated clock or with an external clock. The EXT/INT pin
controls this function. If an external clock is used, the TAG input can be used to daisy-chain multiple ADS8509
data pins together.
INTERNAL DATACLK
In internal clock mode data for the previous conversion is clocked out during each conversion period. The
internal data clock is synchronized to the internal conversion clock so that is does not interfere with the
conversion process.
The DATACLK pin becomes an output when EXT/INT is low. 16 Clock pulses are generated at the beginning of
each conversion after timing t8 is satisfied, i.e. only the previous conversion result can be read during conversion.
DATACLK returns to low when it is inactive. The 16 bits of serial data are shifted out the DATA pin synchronous
to this clock with each bit available on a rising and then a falling edge. The DATA pin returns to the state of the
TAG pin input sensed at the start of transmission.
EXTERNAL DATACLK
The external clock mode offers several ways to retrieve conversion results. However, since the external clock
cannot be synchronized to the internal conversion clock care must be taken to avoid corrupting the data.
16
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
When EXT/INT is set high, the R/C and CS signals control the read state. When the read state is initiated, the
result from the previously completed conversion is shifted out the DATA pin synchronous to the external clock
that is connected to the DATACLK pin. Each bit is available on a falling and then a rising edge. The maximum
external clock speed of 28.5 MHz allows data to be shifted out quickly either at the beginning of conversion or
the beginning of sampling.
There are several modes of operation available when using an external clock. It is recommended that the
external clock run only while reading data. This is discontinuous clock mode. Since the external clock is not
synchronized to the internal clock that controls conversion slight changes in the external clock can cause
conflicts that can corrupt the conversion process. Specifications with a continuously running external clock
cannot be ensured. It is especially important that the external clock does not run during the second half of the
conversion cycle (approximately the time period specified by td11, see the TIMING REQUIREMENTS table).
In discontinuous clock mode data can be read during conversion or during sampling, with or without a SYNC
pulse. Data read during conversion must meet the td11 timing specification. Data read during sampling must be
complete before starting a conversion.
Whether reading during sampling or during conversion a SYNC pulse is generated whenever at least one rising
edge of the external clock occurs while the part is not in the read state. In the discontinuous external clock with
SYNC mode a SYNC pulse follows the first rising edge after the read command. The data is shifted out after the
SYNC pulse. The first rising clock edge after the read command generates a SYNC pulse. The SYNC pulse can
be detected on the next falling edge and then the next rising edge. Successively, each bit can be read first on the
falling edge and then on the next rising edge. Thus 17 clock pulses after the read command are required to read
on the falling edge. 18 Clock pulses are necessary to read on the rising edge.
Table 1. DATACLK Pulses
DESCRIPTION
DATACLK PULSES REQUIRED
WITH SYNC
WITHOUT SYNC
Read on falling edge of DATACLK
17
16
Read on rising edge of DATACLK
18
17
If the clock is entirely inactive when not in the read state a SYNC pulse is not generated. In this case the first
rising clock edge shifts out the MSB. The MSB can be read on the first falling edge or on the next rising edge. In
this discontinuous external clock mode with no SYNC, 16 clocks are necessary to read the data on the falling
edge and 17 clocks for reading on the rising edge. Data always represents the conversion already completed.
TAG FEATURE
The TAG feature allows the data from multiple ADS8509 converters to be read on a single serial line. The
converters are cascaded together using the DATA pins as outputs and the TAG pins as inputs as illustrated in
Figure 27. The DATA pin of the last converter drives the processor's serial data input. Data is then shifted
through each converter, synchronous to the externally supplied data clock, onto the serial data line. The internal
clock cannot be used for this configuration.
The preferred timing uses the discontinuous external data clock during the sampling period. Data must be read
during the sampling period because there is not sufficient time to read data from multiple converters during a
conversion period without violating the td11 constraint (see the EXTERNAL DATACLOCK section). The sampling
period must be sufficiently long to allow all data words to be read before starting a new conversion.
Note, in Figure 27, that a NULL bit separates the data word from each converter. The state of the DATA pin at
the end of a READ cycle reflects the state of the TAG pin at the start of the cycle. This is true in all READ
modes, including the internal clock mode. For example, when a single converter is used in internal clock mode,
the state of the TAG pin determines the state of the DATA pin after all 16 bits have shifted out. When multiple
converters are cascaded together, this state forms the NULL bit that separates the words. Thus, with the TAG
pin of the first converter grounded as shown in Figure 27 the NULL bit becomes a zero between each data word.
17
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
Processor
ADS8509A
DATA
CS
R/C
DATACLK
TAG
SCLK
www.ti.com
ADS 8509B
TAG(A)
DATA
CS
R/C
DATACLK
TAG
TAG(B)
GPIO
GPIO
SDI
Null
D
A00
Q
D
Q
D
Null
D
A15
Q
D
Q
D
B00
DATA (A)
A16
Q
D
Q
D
B15
Q
B16
DATA (B)
Q
DATACLK
R/C
(both A & B)
BUSY
(both A & B)
SYNC
(both A & B)
External
DATACLK
1
2
3
4
16
17
DATA ( A )
A15
A14
A13
A01
A00
DATA ( B )
B15
B14
B13
B01
B00
18
19
20
21
Null
TAG(A) = 0
A
Nth Conversion Data
Null A15
A14 A13
B
EXT/INT tied high, CS of both converter A and B, TAG input of converter A are tied low.
34
A01
35
36
A00
Null
A
TAG(A) = 0
.
Figure 27. Timing of TAG Feature With Single Conversion (Using External DATACLK)
ANALOG INPUTS
The ADS8509 has six analog input ranges as shown in Table 2. The offset and gain specifications are factory
calibrated with 0.1%, 0.25-W, external resistors as shown in Figure 29 and Figure 30. The external resistors can
be omitted if larger gain and offset errors are acceptable or if using software calibration. The hardware trim
circuitry shown in Figure 29 and Figure 30 can reduce the errors to zero.
The analog input pins R1IN, R2IN, and R3IN have ±25-V overvoltage protection. The input signal must be
referenced to AGND1. This minimizes the ground loop problem typical to analog designs. The analog input
should be driven by a low impedance source. A typical driving circuit using OPA627 or OPA132 is shown in
Figure 28.
The ADS8509 can operate with its internal 2.5-V reference or an external reference. An external reference
connected to pin 6 (REF) bypasses the internal reference. The external reference must drive the 4-kΩ resistor
that separates pin 6 from the internal reference (see the illustration on page 1). The load varies with the
difference between the internal and external reference voltages. The external reference voltage can vary from
2.3 V to 2.7 V. The internal reference is approximately 2.5 V. The reference, whether internal or external, is
buffered internally with a buffer with its output on pin 5 (CAP).
The ADS8509 is factory tested with 2.2-mF capacitors connected to pins 5 and 6 (CAP and REF). Each capacitor
should be placed as close as possible to its pin. The capacitor on pin 6 band limits the internal reference noise. A
smaller capacitor can be used but it may degrade SNR and SINAD. The capacitor on pin 5 stabilizes the
reference buffer and provides switching charge to the CDAC during conversion. Capacitors smaller than 1 mF
can cause the buffer to become unstable and may not hold sufficient charge for the CDAC. The parts are tested
to specifications with 2.2 mF so larger capacitors are not necessary. The equivalent series resistor (ESR) of these
compensation capacitors is also critical. The total ESR must be kept under 3 Ω. See the TYPICAL
CHARACTERISTICS section concerning how ESR affects performance.
Neither the internal reference nor the buffer should be used to drive an external load. Such loading can degrade
performance. Any load on the internal reference causes a voltage drop across the 4-kΩ resistor and affects gain.
The internal buffer is capable of driving ±2-mA loads but any load can cause perturbations of the reference at the
CDAC, degrading performance. It should be pointed out that, unlike other competitor’s parts with similar input
structure, the ADS8509 does not require a second high-speed amplifier used as a buffer to isolate the CAP pin
from the signal dependent current in the R3IN pin but can tolerate it if one does exist.
18
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
The external reference voltage can vary from 2.3 V to 2.7 V. The reference voltage determines the size of the
least significant bit (LSB). The larger reference voltages produce a larger LSB, which can improve SNR. Smaller
reference voltages can degrade SNR.
+15V
2.2 mF
22 pF
ADS8509
200 W
100 nF
GND
R1IN
2 kW
Pin 7
2 kW
Vin
Pin 2
22 pF
Pin3
AGND1
Pin 1
100 W
−
OPA 627
or
OPA 132
+
R2IN
Pin 6
33.2 kW
GND
R3IN
Pin4
CAP
2.2 mF
GND
REF
2.2 mF
100 nF
DGND
2.2 mF
GND
AGND2
GND
−15 V
GND
Figure 28. Typical Driving Circuitry (±10 V, No Trim)
19
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
www.ti.com
Table 2. Input Range Connections (See Figure 29 and Figure 30 for Complete
Information)
ANALOG
INPUT RANGE
CONNECT R1IN VIA
200 Ω TO
CONNECT R2IN VIA
100 Ω TO
CONNECT
R3 TO
IMPEDANCE
±10 V
VIN
AGND
CAP
11.5 kΩ
±5 V
AGND
VIN
CAP
6.7 kΩ
±3.33 V
VIN
VIN
CAP
5.4 kΩ
0 V to 10 V
AGND
VIN
AGND
6.7 kΩ
0 V to 5 V
AGND
AGND
VIN
5.0 kΩ
0 V to 4 V
VIN
AGND
VIN
5.4 kΩ
Table 3. Control Truth Table
SPECIFIC FUNCTION
Initiate conversion and
output data using internal
clock
Initiate conversion and
output data using external
clock
CS
R/C
BUSY
EXT/INT
DATACLK
PWRD
SB/BTC
OPERATION
1>0
0
1
0
Output
0
x
0
1>0
1
0
Output
0
x
Initiates conversion n. Data from conversion n - 1
clocked out on DATA synchronized to 16 clock
pulses output on DATACLK.
1>0
0
1
1
Input
0
x
Initiates conversion n.
0
1>0
1
1
Input
0
x
Initiates conversion n.
1>0
1
1
1
Input
x
x
Outputs data with or without SYNC pulse. See
section READING DATA.
1>0
1
0
1
Input
0
x
0
0>1
0
1
Input
0
x
Outputs data with or without SYNC pulse. See
section READING DATA.
0
0
0>1
x
x
0
x
This is an acceptable condition.
x
x
x
x
x
0
x
Analog circuitry powered. Conversion can
proceed..
x
x
x
x
x
1
x
Analog circuitry disabled. Data from previous
conversion maintained in output registers.
x
x
x
x
x
x
0
Serial data is output in binary 2's complement
format.
x
x
x
x
x
x
1
Serial data is output in straight binary format.
No actions
Power down
Select output format
Table 4. Output Codes and Ideal Input Voltages
DIGITAL OUTPUT
DESCRIPTI
ON
BINARY 2'S
COMPLEMENT
(SB/BTC LOW)
ANALOG INPUT
STRAIGHT
BINARY
(SB/BTC HIGH)
BINARY CODE
HEX CODE
BINARY CODE
HEX CODE
3.999939 V
0111 1111 1111 1111
7FFF
1111 1111 1111 1111
FFFF
Full-scale
range
±10
±5
±3.33 V
0 V to 10 V
0 V to 5 V
0 V to 4 V
Least
significant
bit (LSB)
305 mV
153 mV
102 mV
153 mV
76 mV
61 mV
Full scale
(FS - 1LSB)
9.999695 V
4.999847
V
3.333231 V
9.999847 V
4.999924 V
Midscale
0V
0V
0V
5V
2.5 V
2V
0000 0000 0000 0000
0000
1000 0000 0000 0000
8000
One LSB
below
midscale
–305 mV
153 mV
±102 µV
4.999847 V
2.499924 V
1.999939 V
1111 1111 1111 1111
FFFF
0111 1111 1111 1111
7FFF
–Full scale
–10 V
–5 V
–3.333333 V
0V
0V
0V
1000 0000 0000 0000
8000
0000 0000 0000 0000
0000
20
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
Input Range
With Trim
(Adjust Offset First at 0 V, Then Adjust Gain)
Without Trim
200 Ω
200 Ω
R1IN
R1IN
AGND1
AGND1
100 Ω
100 Ω
0 V − 10 V
VIN
R2IN
33.2 kΩ
R3IN
R2IN
VIN
33.2 kΩ
2.2 µF
+5V
CAP
+
50 kΩ
2.2 µF
+
R3IN
2.2 µF
+
+5V
CAP
576 kΩ
50 kΩ
REF
REF
+
2.2 µF
AGND2
200 Ω
AGND2
200 Ω
R1IN
R1IN
AGND1
100 Ω
100 Ω
R2IN
33.2 kΩ
VIN
+5 V
CAP
2.2 µF
+
+5 V
50 kΩ
2.2 µF
REF
2.2 µF
R2IN
33.2 kΩ
R3IN
VIN
0V−5V
AGND1
+
+
R3IN
CAP
576 kΩ
50 kΩ
2.2 µF
AGND2
200 Ω
R1IN
AGND1
100 Ω
100 Ω
R2IN
R2IN
R3IN
R3IN
33.2 kΩ
+5 V
+
33.2 kΩ
+5 V
CAP
2.2 µF
AGND2
R1IN
VIN
AGND1
2.2 µF
REF
200 Ω
VIN
0V−4V
+
+
REF
2.2 µF
+
576 kΩ
50 kΩ
50 kΩ
2.2 µF
AGND2
CAP
REF
+
AGND2
Figure 29. Offset/Gain Circuits for Unipolar Input Ranges
21
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
www.ti.com
With Trim
(Adjust Offset First at 0 V, Then Adjust Gain)
Without Trim
Input Range
200 Ω
VIN
200 Ω
R1IN
R1IN
VIN
AGND1
AGND1
100 Ω
100 Ω
R2IN
±10 V
R2IN
+5 V
R3IN
33.2 kΩ
+
2.2 F
+
R3IN
+5 V
50 kΩ
CAP
2.2 F
33.2 kΩ
REF
2.2 µF
576 kΩ
+
2.2 µF
+
CAP
REF
50 kΩ
AGND2
AGND2
200 Ω
200 Ω
R1IN
R1IN
AGND1
AGND1
100 Ω
VIN
33.2 kΩ
±5V
R3IN
CAP
50 kΩ
2.2 µF
+
2.2 µF
R2IN
R3IN
+
2.2 µF
+5 V
+5 V
+
100 Ω
VIN
33.2 kΩ
R2IN
CAP
576 kΩ
50 kΩ
REF
REF
+
2.2 µF
AGND2
200 Ω
AGND2
200 Ω
VIN
R1IN
100 Ω
R1IN
VIN
100 Ω
AGND1
AGND1
R2IN
R2IN
R3IN
33.2 kΩ
±3.3 V
33.2 kΩ
2.2 µF
+5 V
CAP
+
+
CAP
+5 V
50 kΩ
2.2 F
R3IN
+
REF
2.2 F
AGND2
576 kΩ
50 kΩ
+
2.2 µF
REF
AGND2
Figure 30. Offset/Gain Circuits for Bipolar Input Ranges
22
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
ADS8509
www.ti.com
SLAS324C – OCTOBER 2004 – REVISED APRIL 2010
REVISION HISTORY
Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (April 2007) to Revision C
Page
•
Deleted Lead Temperature from Absolute Maximum Ratings .............................................................................................. 2
•
Changed SB/BTC pin from "O" to "I" .................................................................................................................................... 6
•
Changed location of Timing Requirements table to be closer to timing diagrams ............................................................... 7
23
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): ADS8509
PACKAGE OPTION ADDENDUM
www.ti.com
28-Oct-2010
PACKAGING INFORMATION
Orderable Device
(1)
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
ADS8509IBDB
ACTIVE
SSOP
DB
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
ADS8509IBDBG4
ACTIVE
SSOP
DB
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
ADS8509IBDBR
ACTIVE
SSOP
DB
28
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
ADS8509IBDBRG4
ACTIVE
SSOP
DB
28
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
ADS8509IBDW
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
ADS8509IBDWG4
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
ADS8509IBDWR
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
ADS8509IBDWRG4
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
ADS8509IDB
ACTIVE
SSOP
DB
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
ADS8509IDBG4
ACTIVE
SSOP
DB
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
ADS8509IDBR
ACTIVE
SSOP
DB
28
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
ADS8509IDBRG4
ACTIVE
SSOP
DB
28
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
ADS8509IDW
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
ADS8509IDWG4
ACTIVE
SOIC
DW
20
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
ADS8509IDWR
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
ADS8509IDWRG4
ACTIVE
SOIC
DW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
The marketing status values are defined as follows:
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
28-Oct-2010
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
ADS8509IBDBR
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SSOP
DB
28
2000
330.0
16.4
8.1
10.4
2.5
12.0
16.0
Q1
ADS8509IBDWR
SOIC
DW
20
2000
330.0
24.4
10.8
13.3
2.7
12.0
24.0
Q1
ADS8509IDBR
SSOP
DB
28
2000
330.0
16.4
8.1
10.4
2.5
12.0
16.0
Q1
ADS8509IDWR
SOIC
DW
20
2000
330.0
24.4
10.8
13.3
2.7
12.0
24.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jan-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADS8509IBDBR
SSOP
DB
28
2000
367.0
367.0
38.0
ADS8509IBDWR
SOIC
DW
20
2000
367.0
367.0
45.0
ADS8509IDBR
SSOP
DB
28
2000
367.0
367.0
38.0
ADS8509IDWR
SOIC
DW
20
2000
367.0
367.0
45.0
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
ADS8509IBDBG4 ADS8509IBDWG4 ADS8509IDWG4 ADS8509IBDB ADS8509IBDBR ADS8509IBDBRG4
ADS8509IBDW ADS8509IBDWR ADS8509IBDWRG4 ADS8509IDB ADS8509IDBG4 ADS8509IDBR
ADS8509IDBRG4 ADS8509IDW ADS8509IDWR ADS8509IDWRG4