05133 CP05 thru CP24C STANDARD CAPACITANCE TVS ARRAY APPLICATIONS ✔ Ethernet - 10 Base T ✔ Cellular Phones ✔ Handheld Electronics ✔ FireWire & USB Interfaces ✔ Multiple I/O Ports or Power Supplie IEC COMPATIBILITY (EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns ✔ 61000-4-5 (Surge): 12A, 8/20µs - Level 1(Line-Gnd) & Level 2(Line-Line) SOT-23-6 FEATURES ✔ 200 Watts Peak Pulse Power per Line (tp=8/20µs) ✔ Monolithic Design ✔ Available in Multiple Voltage Types Ranging From 5V to 24V ✔ Protect 4 Bidirectional Lines & 5 Unidirectional Lines ✔ ESD Protection > 25 kilovolts ✔ Low Clamping Voltage ✔ Unidirectional & Bidirectional Configurations ✔ Low Leakage Current ✔ RoHS Compliant MECHANICAL CHARACTERISTICS ✔ ✔ ✔ ✔ Molded JEDEC SOT-23-6 Package Weight 16 milligrams (Approximate) Available in Lead-Free Pure-Tin Plating(Annealed) Solder Reflow Temperature: Pure-Tin - Sn, 100: 260-270°C ✔ Consult Factory for Leaded Device Availability ✔ Flammability Rating UL 94V-0 ✔ 8mm Tape and Reel Per EIA Standard 481 ✔ Marking: Marking Code & Pin One Defined By DOT on Package PIN CONFIGURATIONS UNIDIRECTIONAL 05133.R8 2/07 BIDIRECTIONAL 1 6 1 6 2 5 2 5 3 4 3 4 1 www.protekdevices.com CP05 thru CP24C DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25°C Unless Otherwise Specified PARAMETER SYMBOL VALUE UNITS PPP 200 Watts TL -55 to 150 °C TSTG -55 to 150 °C Peak Pulse Power (tp = 8/20µs) - See Figure 1 Operating Temperature Storage Temperature ELECTRICAL CHARACTERISTICS PER LINE PART NUMBER (See Notes 1-3) DEVICE MARKING CP05 CP05C CP12 CP12C CP15 CP15C CP24 CP24C QRH QRL QRI QRM QRJ QRN QRK QRO @ 25°C Unless Otherwise Specified RATED STAND-OFF VOLTAGE MINIMUM BREAKDOWN VOLTAGE MAXIMUM CLAMPING VOLTAGE (See Fig. 2) MAXIMUM CLAMPING VOLTAGE (See Fig. 2) MAXIMUM LEAKAGE CURRENT TYPICAL CAPACITANCE V WM VOLTS @ 1mA V(BR) VOLTS @ IP = 1A VC VOLTS @8/20µs VC @ IPP @VWM ID µA 0V @ 1 MHz Cj pF 5.0 5.0 12.0 12.0 15.0 15.0 24.0 24.0 6.0 6.0 13.3 13.3 16.7 16.7 26.7 26.7 9.8 9.8 19 19 24 24 43 43 11.8V @ 17.0A 11.8V @ 17.0A 28.3V @ 7.0A 28.3V @ 7.0A 45.0V @ 5.0A 45.0V @ 5.0A 65.0V @ 3.0A 65.0V @ 3.0A 20 20 1 1 1 1 1 1 70 70 50 50 30 30 25 25 Note 1: Part numbers with an additional “C” suffix are bidirectional devices, i.e., CP05C. Note 2: Unidirectional Only: Test between pin 1, 3, 4 and 6 to pin 2 or 5. Note 3: Bidirectional Only: Test between pin 5 to 1 or 3 or 4 or 6. Electrical characteristics apply in both directions. FIGURE 1 PEAK PULSE POWER VS PULSE TIME 120 IPP - Peak Pulse Current - % Of IPP PPP - Peak Pulse Power - Watts 10000 1000 200W 8/20µs Waveform 100 10 0.1 05133.R8 2/07 1 10 100 td - Pulse Duration - µs FIGURE 2 PULSE WAVE FORM 1000 10000 2 tf 100 TEST WAVEFORM PARAMETERS tf = 8µs td = 20µs Peak Value IPP 80 e-t 60 40 td = t IPP/2 20 0 0 5 10 15 20 t - Time - µs 25 30 www.protekdevices.com CP05 thru CP24C GRAPHS FIGURE 3 POWER DERATING CURVE FIGURE 4 OVERSHOOT & CLAMPING VOLTAGE FOR CP05 100 40 Peak Pulse Power 8/20µs 30 5 Volts per Division % Of Rated Power 80 60 40 20 10 20 0 Average Power 0 0 25 50 75 100 125 TL - Lead Temperature - °C 150 ESD Test Pulse: 25 kilovolt, 1/30ns (waveshape) FIGURE 5 TYPICAL CLAMPING VOLTAGE VS PEAK PULSE CURRENT FOR CP05C VC - Clamping Voltage - Volts 16 12 8 4 0 0 5 10 15 IPP - Peak Pulse Current - Amps 20 FIGURE 6 TYPICAL REVERSE VOLTAGE VS CAPACITANCE FOR CP05C 80 C - Capacitance - pF 60 40 20 0 0 05133.R8 2/07 1 2 3 4 VR - Reverse Voltage - Volts 3 5 6 www.protekdevices.com CP05 thru CP24C APPLICATION NOTE The CP Series are TVS arrays designed to protect I/O or data lines from the damaging effects of ESD or EFT. This product series provides both unidirectional and bidirectional protection, with a surge capability of 200 Watts PPP per line for an 8/20µs waveform and ESD protection > 25 kilovolts. UNIDIRECTIONAL COMMON-MODE CONFIGURATION (Figure 1) The CP Series provides up to four (4) lines of protection in a common-mode configuration as depicted in Figure 1. Circuit connectivity is as follows: ✔ Line 1 is connected to Pin 1. ✔ Line 2 is connected to Pin 3. ✔ Line 3 is connected to Pin 4. ✔ Line 4 is connected to Pin 6. ✔ Pin 5 is connected to ground. ✔ Pin 2 is not connected. Figure 1 - Unidirectional Configuration Common-Mode I/O Port Protection LINE 1 LINE 2 3 2 1 4 5 6 The CPxxC Series provides up to four (4) lines of protection in a common-mode configuration as depicted in Figure 2. I/O PORT BIDIRECTIONAL COMMON-MODE CONFIGURATION (Figure 2) Circuit connectivity is as follows: ✔ Line 1 is connected to Pin 1. ✔ Line 2 is connected to Pin 3. ✔ Line 3 is connected to Pin 4. ✔ Line 4 is connected to Pin 5. ✔ Pin 6 is connected to ground. ✔ Pin 2 is not connected. LINE 3 LINE 4 CIRCUIT BOARD LAYOUT RECOMMENDATIONS Circuit board layout is critical for Electromagnetic Compatibility (EMC) protection. The following guidelines are recommended: Figure 2 - Bidirectional Configuration Common-Mode I/O Port Protection The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. LINE 1 LINE 2 ✔ The path length between the TVS device and the protected line should be minimized. ✔ All conductive loops including power and ground loops should be minimized. ✔ The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. ✔ Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. 3 2 1 4 5 6 I/O PORT ✔ LINE 3 LINE 4 05133.R8 2/07 4 www.protekdevices.com CP05 thru CP24C SOT-23-6 PACKAGE OUTLINE & DIMENSIONS PACKAGE OUTLINE D SOT-23-6 E 6 5 4 3 2 PACKAGE DIMENSIONS 0° - 8° K 1 L J F A B C D E F G J K L M M B A G C MOUNTING PAD 4 TYPICAL 0.70 1.90 0.95 2.40 1.00 2.80 1.50 0.90 0.35 0.85 1.70 0.90 0.09 2.60 0.20 TYP 0.35 3.05 1.75 1.30 0.50 1.05 2.10 1.45 0.20 3.00 0.20 TYP 0.55 0.110 0.059 0.036 0.014 0.033 0.067 0.036 0.003 0.102 0.007 TYP 0.014 0.120 0.070 0.051 0.020 0.040 0.083 0.057 0.008 0.118 0.007 TYP 0.022 NOTES 1. Dimensioning and tolerances per ANSI Y14.5M, 1985. 2. Controlling Dimension: Inches 3. Dimensions are exclusive of mold flash and metal burrs. DIM Millimeters Inches 1 2 3 4 5 INCHES MIN MAX MILLIMETERS MIN MAX DIM 0.028 0.074 0.037 0.094 0.039 TAPE & REEL/BULK ORDERING NOMENCLATURE 3 1. Surface mount product is taped and reeled in accordance with EIA-481. 2. Suffix -T7 = 7 Inch Reel - 3,000 pieces per 8mm tape, i.e., CP05-T7 3. Suffix - LF = Lead-Free, Pure-Tin Plating, i.e., CP05-LF-T7. 2 1 5 Outline & Dimensions: Rev 2 - 10/05, 06013 Tape & Reel Specifications (Dimensions in millimeters) Reel Dia. Tape Width 178mm (7”) 8mm A0 B0 K0 D E F P0 W P2 P 3.20 ± 0.10 3.20 ± 0.10 1.65 ± 0.10 1.50 ± 0.10 1.75 ± 0.10 3.50 ± 0.05 8.00 ±0.30 4.00 ±0.10 2.00 ±0.05 4.00 ±0.10 P0 t P2 D tmax 0.25 10 Pitches Cumulative Tolerance on Tape. ± 0.2 E Pin 1 Indicated by Dot Top cover tape A0 F W K0 B0 P User Direction of Feed COPYRIGHT © ProTek Devices 2007 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. 05133.R8 2/07 5 ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: [email protected] Web Site: www.protekdevices.com www.protekdevices.com