14.22mm (0.56INCH) THREE DIGIT NUMERIC DISPLAY Part Number: BA56-12CGKWA Green Features Description z 0.56 inch digit height. The Green source color devices are made with AlGaInP on z Low current operation. GaAs substrate Light Emitting Diode. z Excellent character appearance. z Easy mounting on P.C. boards or sockets. z Mechanically rugged. z Standard: gray face, white segment. z RoHS compliant. Package Dimensions& Internal Circuit Diagram Notes: 1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAM8320 REV NO: V.2A DATE: MAR/20/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1303000564 Selection Guide Part No. Dice BA56-12CGKWA Iv (ucd) [1] @ 10mA Lens Type Green (AlGaInP) Description Min. Typ. 14000 35000 *5600 *11000 White Diffused Common Anode ,Rt. Hand Decimal. Notes: 1. Luminous intensity/ luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 574 nm IF=20mA Green 570 nm IF=20mA Spectral Line Half-width Green 20 nm IF=20mA C Capacitance Green 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 2.1 2.5 V IF=20mA IR Reverse Current Green 10 uA VR=5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Green Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating / Storage Temperature Lead Solder Temperature[2] -40°C To +85°C 260°C For 3-5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. SPEC NO: DSAM8320 REV NO: V.2A DATE: MAR/20/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1303000564 Green BA56-12CGKWA SPEC NO: DSAM8320 REV NO: V.2A DATE: MAR/20/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1303000564 PACKING & LABEL SPECIFICATIONS BA56-12CGKWA Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAM8320 REV NO: V.2A DATE: MAR/20/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1303000564 SPEC NO: DSAM8320 REV NO: V.2A DATE: MAR/20/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1303000564 SPEC NO: DSAM8320 REV NO: V.2A DATE: MAR/20/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1303000564