AD ADUM3440CRWZ Quad channel, high speed digital isolator Datasheet

APPLICATIONS
High speed multichannel isolation
SPI interface/data converter isolation
Instrumentation
FUNCTIONAL BLOCK DIAGRAMS
ADuM3440
VDD1 1
GND1 2
16
VDD2
15
GND2
VIA 3
ENCODE
DECODE
14
VOA
VIB 4
ENCODE
DECODE
13
VOB
VIC 5
ENCODE
DECODE
12
VOC
VID 6
ENCODE
DECODE
11
VOD
NC 7
10
VE2
GND1 8
9
GND2
06837-001
Low power operation
5 V operation
1.7 mA per channel maximum @ 0 Mbps to 2 Mbps
68 mA per channel maximum @ 150 Mbps
3.3 V operation
1.0 mA per channel maximum @ 0 Mbps to 2 Mbps
33 mA per channel maximum @ 150 Mbps
Bidirectional communication
3.3 V/5 V level translation
High temperature operation: 105°C
High data rate: dc to 150 Mbps (NRZ)
Precise timing characteristics
5 ns maximum pulse width distortion
5 ns maximum channel-to-channel matching
High common-mode transient immunity: >25 kV/μs
Output enable function
16-lead SOIC wide body package
Safety and regulatory approvals
UL recognition: 2500 V rms for 1 minute per UL 1577
CSA Component Acceptance Notice #5A
VDE certificate of conformity
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
VIORM = 560 V peak
Figure 1. ADuM3440 Functional Block Diagram
ADuM3441
VDD1 1
GND1 2
16
VDD2
15
GND2
VIA 3
ENCODE
DECODE
14
VOA
VIB 4
ENCODE
DECODE
13
VOB
VIC 5
ENCODE
DECODE
12
VOC
VOD 6
DECODE
ENCODE
11
VID
VE1 7
10
VE2
GND1 8
9
GND2
06837-002
FEATURES
Figure 2. ADuM3441 Functional Block Diagram
ADuM3442
VDD1 1
GND1 2
16
VDD2
15
GND2
VIA 3
ENCODE
DECODE
14
VOA
VIB 4
ENCODE
DECODE
13
VOB
VOC 5
DECODE
ENCODE
12
VIC
VOD 6
DECODE
ENCODE
11
VID
VE1 7
10
VE2
GND1 8
9
GND2
06837-003
Data Sheet
Quad Channel, High Speed
Digital Isolators
ADuM3440/ADuM3441/ADuM3442
Figure 3. ADuM3442 Functional Block Diagram
GENERAL DESCRIPTION
The ADuM344x1 are four channel, digital isolators based on the
Analog Devices, Inc., iCoupler® technology supporting data rates
up to 150 Mbps. Combining high speed CMOS and monolithic
air core transformer technology, these isolation components
provide outstanding performance characteristics superior to
alternatives such as optocoupler devices.
By avoiding the use of LEDs and photodiodes, iCoupler
devices remove the design difficulties commonly associated
with optocouplers. The typical optocoupler concerns regarding
uncertain current transfer ratios, nonlinear transfer functions,
and temperature and lifetime effects are eliminated with the
simple iCoupler digital interfaces and stable performance
characteristics. The need for external drivers and other discrete
components is eliminated with these iCoupler products.
1
Furthermore, iCoupler devices consume one-tenth to one-sixth
the power of optocouplers at comparable signal data rates.
The ADuM344x isolators provide four independent isolation
channels in a variety of channel configurations (see the
Ordering Guide). The ADuM344x operates with the supply
voltage on either side ranging from 3.0 V to 5.5 V, providing
compatibility with lower voltage systems as well as enabling
voltage translation functionality across the isolation barrier. In
addition, the ADuM344x provides low pulse width distortion
and tight channel-to-channel matching. Unlike other optocoupler alternatives, the ADuM344x isolators have a patented
refresh feature that ensures dc correctness in the absence of
input logic transitions and during the power-up/power-down
condition.
Protected by U.S. Patents 5,952,849; 6,873,065; 6,903,578; and 7,075,329.
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2007–2012 Analog Devices, Inc. All rights reserved.
ADuM3440/ADuM3441/ADuM3442
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Absolute Maximum Ratings ......................................................... 12
Applications ....................................................................................... 1
ESD Caution................................................................................ 12
Functional Block Diagrams ............................................................. 1
Pin Configurations and Function Descriptions ......................... 13
General Description ......................................................................... 1
Typical Performance Characteristics ........................................... 16
Revision History ............................................................................... 2
Applications Information .............................................................. 18
Specifications..................................................................................... 3
PC Board Layout ........................................................................ 18
Electrical Characteristics—5 V Operation................................ 3
Propagation Delay-Related Parameters................................... 18
Electrical Characteristics—3.3 V Operation ............................ 5
System-Level ESD Considerations and Enhancements ........ 18
Electrical Characteristics—Mixed 5 V/3.3 V or 3.3 V/5 V
Operation....................................................................................... 7
DC Correctness and Magnetic Field Immunity........................... 18
Package Characteristics ............................................................. 10
Insulation Lifetime ..................................................................... 20
Regulatory Information ............................................................. 10
Outline Dimensions ....................................................................... 21
Insulation and Safety-Related Specifications .......................... 10
Ordering Guide .......................................................................... 21
Power Consumption .................................................................. 19
DIN V VDE V 0884-10 (VDE V 0884-10) Insulation
Characteristics ............................................................................ 11
Recommended Operating Conditions .................................... 11
REVISION HISTORY
2/12—Rev. C to Rev. D
Created Hyperlink for Safety and Regulatory Approvals
Entry in Features Section................................................................. 1
Change to PC Board Layout Section ............................................ 18
Updated Outline Dimensions ....................................................... 21
1/09—Rev. B to Rev. C
Change to Propagation Delay Parameter (Table 1) ...................... 3
Change to Propagation Delay Parameter (Table 2) ...................... 5
Change to Propagation Delay Parameter (Table 3) ...................... 8
9/08—Rev. A to Rev. B
Changes to Pulse Width Distortion, |tPLH − tPHL| Parameter and
Channel-to-Channel Matching, Codirectional Channels
Parameter, Table 1 .............................................................................3
Changes to Pulse Width Distortion, |tPLH − tPHL| Parameter and
Channel-to-Channel Matching, Codirectional Channels
Parameter, Table 2 .............................................................................5
Changes to Pulse Width Distortion, |tPLH − tPHL| Parameter and
Channel-to-Channel Matching, Codirectional Channels
Parameter, Table 3 .............................................................................8
5/08—Rev. 0 to Rev. A
Changes to Ordering Guide .......................................................... 21
11/07—Rev. 0: Initial Version
Rev. D | Page 2 of 24
Data Sheet
ADuM3440/ADuM3441/ADuM3442
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS—5 V OPERATION
All voltages are relative to their respective ground. 4.5 V ≤ VDD1 ≤ 5.5 V, 4.5 V ≤ VDD2 ≤ 5.5 V. All minimum/maximum specifications
apply over the entire recommended operation range, unless otherwise noted. All typical specifications are at TA = 25°C, VDD1 = VDD2 = 5 V.
Table 1.
Parameter
DC SPECIFICATIONS
Input Supply Current per Channel, Quiescent
Output Supply Current per Channel, Quiescent
ADuM3440, Total Supply Current, Four Channels 1
DC to 2 Mbps
VDD1 Supply Current
VDD2 Supply Current
150 Mbps
VDD1 Supply Current
VDD2 Supply Current
ADuM3441, Total Supply Current, Four Channels1
DC to 2 Mbps
VDD1 Supply Current
VDD2 Supply Current
150 Mbps
VDD1 Supply Current
VDD2 Supply Current
ADuM3442, Total Supply Current, Four Channels1
DC to 2 Mbps
VDD1 or VDD2 Supply Current
150 Mbps
VDD1 or VDD2 Supply Current
For All Models
Input Currents
Logic High Input Threshold
Logic Low Input Threshold
Logic High Output Voltages
Logic Low Output Voltages
SWITCHING SPECIFICATIONS
Minimum Pulse Width 2
Maximum Data Rate 3
Propagation Delay 4
Pulse Width Distortion, |tPLH − tPHL| 5
Change vs. Temperature
Propagation Delay Skew 6
Channel-to-Channel Matching,
Codirectional Channels5
Channel-to-Channel Matching,
Opposing Directional Channels5
Symbol
Min
Typ
Max
Unit
IDDI (Q)
IDDO (Q)
0.75
0.5
1.3
1.2
mA
mA
IDD1 (Q)
IDD2 (Q)
3
2
3.9
3
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
IDD1 (150)
IDD2 (150)
120
47
220
55
mA
mA
75 MHz logic signal frequency
75 MHz logic signal frequency
IDD1 (Q)
IDD2 (Q)
2.8
2.3
3.6
2.9
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
IDD1 (150)
IDD2 (150)
101
65
165
80
mA
mA
75 MHz logic signal frequency
75 MHz logic signal frequency
IDD1 (Q), IDD2 (Q)
2.5
3.5
mA
DC to 1 MHz logic signal frequency
IDD1 (150), IDD2 (150)
83
130
mA
75 MHz logic signal frequency
+0.01
+10
µA
0 ≤ VIA, VIB, VIC, VID ≤ VDD1 or VDD2,
0 ≤ VE1, VE2 ≤ VDD1 or VDD2
0.8
5.0
V
V
V
IOx = −20 µA, VIx = VIxH
4.8
V
IOx = −4 mA, VIx = VIxH
IIA, IIB, IIC,
IID, IE1, IE2
VIH, VEH
VIL, VEL
VOAH, VOBH,
VOCH, VODH
−10
2.0
(VDD1 or
VDD2) − 0.1
(VDD1 or
VDD2) − 0.4
VOAL, VOBL,
VOCL, VODL
0.0
0.1
V
IOx = 20 µA, VIx = VIxL
0.04
0.2
0.1
0.4
V
V
IOx = 400 µA, VIx = VIxL
IOx = 4 mA, VIx = VIxL
6.67
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
PW
tPSK
tPSKCD
12
2
ns
Mbps
ns
ns
ps/°C
ns
ns
tPSKOD
5
ns
tPHL, tPLH
PWD
150
20
0.5
3
Rev. D | Page 3 of 24
Test Conditions
32
2
ADuM3440/ADuM3441/ADuM3442
Parameter
For All Models
Output Disable Propagation Delay
(High/Low to High Impedance)
Output Enable Propagation Delay
(High Impedance to High/Low)
Output Rise/Fall Time (10% to 90%)
Common-Mode Transient Immunity
at Logic High Output 7
Common-Mode Transient Immunity
at Logic Low Output7
Refresh Rate
Input Dynamic Supply Current per Channel 8
Output Dynamic Supply Current per Channel8
Symbol
Data Sheet
Min
Typ
Max
Unit
Test Conditions
tPHZ, tPLH
6
8
ns
CL = 15 pF, CMOS signal levels
tPZH, tPZL
6
8
ns
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
VIx = VDD1 or VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
tR/tF
|CMH|
25
2.5
35
ns
kV/µs
|CML|
25
35
kV/µs
1.2
0.196
0.1
Mbps
mA/Mbps
mA/Mbps
fr
IDDI (D)
IDDO (D)
1
The supply current values for all four channels are combined when running at identical data rates. Output supply current values are specified with no output load
present. The supply current associated with an individual channel operating at a given data rate may be calculated as described in the Power Consumption section.
See Figure 8 through Figure 10 for information on per-channel supply current as a function of data rate for unloaded and loaded conditions. See Figure 11 through
Figure 15 for total VDD1 and VDD2 supply currents as a function of data rate for ADuM3440/ADuM3441/ADuM3442 channel configurations.
2
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
3
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
4
tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
5
Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing-directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
inputs on opposing sides of the isolation barrier.
6
tPSK is the magnitude of the worst-case difference in tPHL or tPLH that is measured between units at the same operating temperature, supply voltages, and output load
within the recommended operating conditions.
7
CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDDO. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VO < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
magnitude is the range over which the common mode is slewed.
8
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See Figure 8 through Figure 10 for information
on per-channel supply current for unloaded and loaded conditions. See the Power Consumption section for guidance on calculating the per-channel supply current
for a given data rate.
Rev. D | Page 4 of 24
Data Sheet
ADuM3440/ADuM3441/ADuM3442
ELECTRICAL CHARACTERISTICS—3.3 V OPERATION
All voltages are relative to their respective ground. 3.0 V ≤ VDD1 ≤ 3.6 V, 3.0 V ≤ VDD2 ≤ 3.6 V. All minimum/maximum specifications apply
over the entire recommended operation range, unless otherwise noted. All typical specifications are at TA = 25°C, VDD1 = VDD2 = 3.3 V.
Table 2.
Parameter
DC SPECIFICATIONS
Input Supply Current per Channel, Quiescent
Output Supply Current per Channel, Quiescent
ADuM3440, Total Supply Current, Four Channels 1
DC to 2 Mbps
VDD1 Supply Current
VDD2 Supply Current
150 Mbps
VDD1 Supply Current
VDD2 Supply Current
ADuM3441, Total Supply Current, Four Channels1
DC to 2 Mbps
VDD1 Supply Current
VDD2 Supply Current
150 Mbps
VDD1 Supply Current
VDD2 Supply Current
ADuM3442, Total Supply Current, Four Channels1
DC to 2 Mbps
VDD1 or VDD2 Supply Current
150 Mbps
VDD1 or VDD2 Supply Current
For All Models
Input Currents
Logic High Input Threshold
Logic Low Input Threshold
Logic High Output Voltages
Logic Low Output Voltages
Symbol
Typ
Max
Unit
IDDI (Q)
IDDO (Q)
0.43
0.3
0.90
0.60
mA
mA
IDD1 (Q)
IDD2 (Q)
1.7
1.2
2.4
1.7
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
IDD1 (150)
IDD2 (150)
63
17
110
25
mA
mA
75 MHz logic signal frequency
75 MHz logic signal frequency
IDD1 (Q)
IDD2 (Q)
1.6
1.3
2.2
1.9
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
IDD1 (150)
IDD2 (150)
52
29
80
40
mA
mA
75 MHz logic signal frequency
75 MHz logic signal frequency
IDD1 (Q), IDD2 (Q)
1.5
2.0
mA
DC to 1 MHz logic signal frequency
IDD1 (150), IDD2 (150)
40
66
mA
75 MHz logic signal frequency
+0.01
+10
µA
0 ≤ VIA, VIB, VIC, VID ≤ VDD1 or VDD2,
0 ≤ VE1, VE2 ≤ VDD1 or VDD2
0.4
V
V
V
IOx = −20 µA, VIx = VIxH
V
IOx = −4 mA, VIx = VIxH
0.1
V
IOx = 20 µA, VIx = VIxL
0.1
0.4
V
V
IOx = 400 µA, VIx = VIxL
IOx = 4 mA, VIx = VIxL
6.67
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
IIA, IIB, IIC,
IID, IE1, IE2
VIH, VEH
VIL, VEL
VOAH, VOBH,
VOCH, VODH
VOAL, VOBL,
VOCL, VODL
Min
−10
1.6
(VDD1 or
3.0
VDD2) − 0.1
2.8
(VDD1 or
VDD2) − 0.4
0.0
0.04
0.2
SWITCHING SPECIFICATIONS
Minimum Pulse Width 2
Maximum Data Rate 3
Propagation Delay 4
Pulse Width Distortion, |tPLH − tPHL|4
Change vs. Temperature
Propagation Delay Skew 5
Channel-to-Channel Matching,
Codirectional Channels 6
Channel-to-Channel Matching,
Opposing Directional Channels5
PW
tPSK
tPSKCD
16
2
ns
Mbps
ns
ns
ps/°C
ns
ns
tPSKOD
5
ns
tPHL, tPLH
PWD
150
20
0.5
3
Rev. D | Page 5 of 24
36
2
Test Conditions
ADuM3440/ADuM3441/ADuM3442
Parameter
For All Models
Output Disable Propagation Delay
(High/Low to High Impedance)
Output Enable Propagation Delay
(High Impedance to High/Low)
Output Rise/Fall Time (10% to 90%)
Common-Mode Transient Immunity
at Logic High Output 7
Common-Mode Transient Immunity
at Logic Low Output7
Refresh Rate
Input Dynamic Supply Current per Channel 8
Output Dynamic Supply Current per Channel8
Symbol
Data Sheet
Min
Typ
Max
Unit
Test Conditions
tPHZ, tPLH
6
8
ns
CL = 15 pF, CMOS signal levels
tPZH, tPZL
6
8
ns
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
VIx = VDD1 or VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
tR/tF
|CMH|
25
3
35
ns
kV/µs
|CML|
25
35
kV/µs
1.1
0.076
0.028
Mbps
mA/Mbps
mA/Mbps
fr
IDDI (D)
IDDO (D)
1
The supply current values for all four channels are combined when running at identical data rates. Output supply current values are specified with no output load
present. The supply current associated with an individual channel operating at a given data rate may be calculated as described in the Power Consumption section.
See Figure 8 through Figure 10 for information on per-channel supply current as a function of data rate for unloaded and loaded conditions. See Figure 11 through
Figure 15 for total VDD1 and VDD2 supply currents as a function of data rate for ADuM3440/ADuM3441/ADuM3442 channel configurations.
2
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
3
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
4
tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
5
tPSK is the magnitude of the worst-case difference in tPHL or tPLH that is measured between units at the same operating temperature, supply voltages, and output load
within the recommended operating conditions.
6
Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
inputs on opposing sides of the isolation barrier.
7
CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDDO. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VO < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
magnitude is the range over which the common mode is slewed.
8
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See Figure 8 through Figure 10 for information
on per-channel supply current for unloaded and loaded conditions. See the Power Consumption section for guidance on calculating the per-channel supply current
for a given data rate.
Rev. D | Page 6 of 24
Data Sheet
ADuM3440/ADuM3441/ADuM3442
ELECTRICAL CHARACTERISTICS—MIXED 5 V/3.3 V OR 3.3 V/5 V OPERATION
All voltages are relative to their respective ground. 5 V/3.3 V operation: 4.5 V ≤ VDD1 ≤ 5.5 V, 3.0 V ≤ VDD2 ≤ 3.6 V; 3 V/5 V operation:
3.0 V ≤ VDD1 ≤ 3.6 V, 4.5 V ≤ VDD2 ≤ 5.5 V. All minimum/maximum specifications apply over the entire recommended operating range,
unless otherwise noted. All typical specifications are at TA = 25°C; VDD1 = 3.3 V, VDD2 = 5 V or VDD1 = 5 V, VDD2 = 3.3 V.
Table 3.
Parameter
DC SPECIFICATIONS
Input Supply Current per Channel, Quiescent
5 V/3.3 V Operation
3.3 V/5 V Operation
Output Supply Current per Channel, Quiescent
5 V/3.3 V Operation
3.3 V/5 V Operation
ADuM3440, Total Supply Current, Four Channels 1
DC to 2 Mbps
VDD1 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
VDD2 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
150 Mbps
VDD1 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
VDD2 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
ADuM3441, Total Supply Current, Four Channels1
DC to 2 Mbps
VDD1 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
VDD2 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
150 Mbps
VDD1 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
VDD2 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
ADuM3442, Total Supply Current, Four Channels1
DC to 2 Mbps
VDD1 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
VDD2 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
Symbol
Min
Typ
Max
Unit
Test Conditions
0.75
0.43
1.3
0.9
mA
mA
0.3
0.5
0.7
1.2
mA
mA
3
1.7
3.9
2.4
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
1.2
2
1.7
3
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
120
63
220
110
mA
mA
75 MHz logic signal frequency
75 MHz logic signal frequency
17
47
25
55
mA
mA
75 MHz logic signal frequency
75 MHz logic signal frequency
2.8
1.6
3.6
2.2
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
1.3
2.3
1.9
2.9
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
101
52
165
80
mA
mA
75 MHz logic signal frequency
75 MHz logic signal frequency
29
65
40
80
mA
mA
75 MHz logic signal frequency
75 MHz logic signal frequency
2.5
1.5
3.5
2.0
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
1.5
2.5
2.0
3.5
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
IDDI (Q)
IDDO (Q)
IDD1 (Q)
IDD2 (Q)
IDD1 (150)
IDD2 (150)
IDD1 (Q)
IDD2 (Q)
IDD1 (150)
IDD2 (150)
IDD1 (Q)
IDD2 (Q)
Rev. D | Page 7 of 24
ADuM3440/ADuM3441/ADuM3442
Parameter
150 Mbps
VDD1 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
VDD2 Supply Current
5 V/3.3 V Operation
3.3 V/5 V Operation
For All Models
Input Currents
Logic High Input Threshold
5 V/3.3 V Operation
3.3 V/5 V Operation
Logic Low Input Threshold
5 V/3.3 V Operation
3.3 V/5 V Operation
Logic High Output Voltages
Logic Low Output Voltages
SWITCHING SPECIFICATIONS
Minimum Pulse Width 2
Maximum Data Rate 3
Propagation Delay 4
Pulse Width Distortion, |tPLH − tPHL|4
Change vs. Temperature
Propagation Delay Skew 5
Channel-to-Channel Matching,
Codirectional Channels 6
Channel-to-Channel Matching,
Opposing Directional Channels5
For All Models
Output Disable Propagation Delay
(High/Low to High Impedance)
Output Enable Propagation Delay
(High Impedance to High/Low)
Output Rise/Fall Time (10% to 90%)
5 V/3 V Operation
3 V/5 V Operation
Common-Mode Transient Immunity
at Logic High Output 7
Common-Mode Transient Immunity
at Logic Low Output7
Refresh Rate
5 V/3.3 V Operation
3.3 V/5 V Operation
Input Dynamic Supply Current per Channel 8
5 V/3.3 V Operation
3.3 V/5 V Operation
Output Dynamic Supply Current per Channel8
5 V/3.3 V Operation
3.3 V/5 V Operation
Symbol
Data Sheet
Min
Typ
Max
Unit
Test Conditions
83
40
130
66
mA
mA
75 MHz logic signal frequency
75 MHz logic signal frequency
40
83
66
130
mA
mA
75 MHz logic signal frequency
75 MHz logic signal frequency
+0.01
+10
µA
0 ≤ VIA,VIB, VIC,VID ≤ VDD1 or VDD2,
0 ≤ VE1,VE2 ≤ VDD1 or VDD2
IDD1 (150)
IDD2 (150)
IIA, IIB, IIC,
IID, IE1, IE2
VIH, VEH
−10
2.0
1.6
V
V
VIL, VEL
0.8
0.4
VOAH, VOBH,
VOCH, VODH
(VDD1 or
VDD2) − 0.1
(VDD1 or
VDD2) − 0.4
VOAL, VOBL,
VOCL, VODL
V
V
V
IOx = −20 µA, VIx = VIxH
V
IOx = −4 mA, VIx = VIxH
(VDD1 or
VDD2)
(VDD1 or
VDD2) − 0.2
0.0
0.1
V
IOx = 20 µA, VIx = VIxL
0.04
0.2
0.1
0.4
V
V
IOx = 400 µA, VIx = VIxL
IOx = 4 mA, VIx = VIxL
6.67
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
PW
tPSK
tPSKCD
15
2
ns
Mbps
ns
ns
ps/°C
ns
ns
tPSKOD
5
ns
CL = 15 pF, CMOS signal levels
tPHL, tPLH
PWD
150
20
0.5
3
35
2
tPHZ, tPLH
6
8
ns
CL = 15 pF, CMOS signal levels
tPZH, tPZL
6
8
ns
CL = 15 pF, CMOS signal levels
tR/tF
CL = 15 pF, CMOS signal levels
|CMH|
25
3.0
2.5
35
ns
ns
kV/µs
|CML|
25
35
kV/µs
1.2
1.1
Mbps
Mbps
0.196
0.076
mA/Mbps
mA/Mbps
0.028
0.01
mA/Mbps
mA/Mbps
fr
IDDI (D)
IDDO (D)
Rev. D | Page 8 of 24
VIx = VDD1 or VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
Data Sheet
ADuM3440/ADuM3441/ADuM3442
1
The supply current values for all four channels are combined when running at identical data rates. Output supply current values are specified with no output load
present. The supply current associated with an individual channel operating at a given data rate may be calculated as described in the Power Consumption section.
See Figure 8 through Figure 10 for information on per-channel supply current as a function of data rate for unloaded and loaded conditions. See Figure 11 through
Figure 15 for total VDD1 and VDD2 supply currents as a function of data rate for ADuM3440/ADuM3441/ADuM3442 channel configurations.
2
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
3
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
4
tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
5
tPSK is the magnitude of the worst-case difference in tPHL or tPLH that is measured between units at the same operating temperature, supply voltages, and output load
within the recommended operating conditions.
6
Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
inputs on opposing sides of the isolation barrier.
7
CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDDO. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VO < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
magnitude is the range over which the common mode is slewed.
8
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See Figure 8 through Figure 10 for information
on per-channel supply current for unloaded and loaded conditions. See the Power Consumption section for guidance on calculating the per-channel supply current
for a given data rate.
Rev. D | Page 9 of 24
ADuM3440/ADuM3441/ADuM3442
Data Sheet
PACKAGE CHARACTERISTICS
Table 4.
Parameter
Resistance (Input to Output) 1
Capacitance (Input to Output)1
Input Capacitance 2
IC Junction-to-Case Thermal Resistance, Side 1
IC Junction-to-Case Thermal Resistance, Side 2
1
2
Symbol
RI-O
CI-O
CI
θJCI
θJCO
Min
Typ
1012
2.2
4.0
33
28
Max
Unit
Ω
pF
pF
°C/W
°C/W
Test Conditions
f = 1 MHz
Thermocouple located at
center of package underside
The device is considered a 2-terminal device; Pin 1 through Pin 8 are shorted together and Pin 9 through Pin 16 are shorted together.
Input capacitance is from any input data pin to ground.
REGULATORY INFORMATION
The ADuM344x is approved by the organizations listed in Table 5. Refer to Table 10 and the Insulation Lifetime section for details
regarding recommended maximum working voltages for specific cross-isolation waveforms and insulation levels.
Table 5.
UL
Recognized under
1577 component recognition program 1
Single protection,
2500 V rms isolation voltage
File E214100
CSA
Approved under
CSA Component Acceptance Notice #5A
Basic insulation per CSA 60950-1-03 and
IEC 60950-1, 800 V rms (1131 V peak)
maximum working voltage
Reinforced insulation per CSA 60950-1-03
and IEC 60950-1, 400 V rms (566 V peak)
maximum working voltage
File 205078
VDE
Certified according to
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 2
Reinforced insulation, 560 V peak
File 2471900-4880-0001
1
In accordance with UL 1577, each ADuM344x is proof tested by applying an insulation test voltage ≥3000 V rms for 1 sec (current leakage detection limit = 5 µA).
2
In accordance with DIN V VDE V 0884-10, each ADuM344x is proof tested by applying an insulation test voltage ≥1050 V peak for 1 sec (partial discharge detection
limit = 5 pC). An asterisk (*) marking branded on the component designates DIN V VDE V 0884-10 approval.
INSULATION AND SAFETY-RELATED SPECIFICATIONS
Table 6.
Parameter
Rated Dielectric Insulation Voltage
Minimum External Air Gap (Clearance)
Symbol
L(I01)
Value
2500
7.7 min
Minimum External Tracking (Creepage)
L(I02)
8.1 min
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Isolation Group
CTI
0.017 min
>175
IIIa
Unit Conditions
V rms 1-minute duration
mm Measured from input terminals to output terminals,
shortest distance through air
mm Measured from input terminals to output terminals,
shortest distance path along body
mm Insulation distance through insulation
V
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
Rev. D | Page 10 of 24
Data Sheet
ADuM3440/ADuM3441/ADuM3442
DIN V VDE V 0884-10 (VDE V 0884-10) INSULATION CHARACTERISTICS
These isolators are suitable for reinforced electrical isolation only within the safety limit data. Maintenance of the safety data is ensured by
protective circuits. The asterisk (*) marking on packages denotes DIN V VDE V 0884-10 approval.
Table 7.
Description
Installation Classification per DIN VDE 0110
For Rated Mains Voltage ≤ 150 V rms
For Rated Mains Voltage ≤ 300 V rms
For Rated Mains Voltage ≤ 400 V rms
Climatic Classification
Pollution Degree per DIN VDE 0110, Table 1
Maximum Working Insulation Voltage
Input-to-Output Test Voltage, Method B1
Input-to-Output Test Voltage, Method A
After Environmental Tests Subgroup 1
After Input and/or Safety Test
Subgroup 2 and Subgroup 3
Highest Allowable Overvoltage
Safety-Limiting Values
VIORM × 1.875 = VPR, 100% production test, tm = 1 sec,
partial discharge < 5 pC
VIORM × 1.6 = VPR, tm = 60 sec, partial discharge < 5 pC
Symbol
Characteristic
Unit
VIORM
VPR
I to IV
I to III
I to II
40/105/21
2
560
1050
V peak
V peak
896
672
V peak
V peak
VTR
4000
V peak
TS
IS1
IS2
RS
150
265
335
>109
°C
mA
mA
Ω
VPR
VIORM × 1.2 = VPR, tm = 60 sec, partial discharge < 5 pC
Transient overvoltage, tTR = 10 seconds
Maximum value allowed in the event of a failure
(see Figure 4)
VIO = 500 V
350
RECOMMENDED OPERATING CONDITIONS
300
Table 8.
Parameter
Operating Temperature Range, TA
Supply Voltage Range, VDD1, VDD2 1
Input Signal Rise and Fall Time
250
SIDE #2
200
150
1
SIDE #1
100
50
0
0
50
100
150
CASE TEMPERATURE (°C)
200
Rating
−40°C to +105°C
3.0 V to 5.5 V
1.0 ms
All voltages are relative to their respective ground. See the DC Correctness
and Magnetic Field Immunity section for information on immunity to external
magnetic fields.
06837-004
SAFETY-LIMITING CURRENT (mA)
Case Temperature
Side 1 Current
Side 2 Current
Insulation Resistance at TS
Conditions
Figure 4. Thermal Derating Curve, Dependence of Safety-Limiting Values
with Case Temperature per DIN V VDE V 0884-10
Rev. D | Page 11 of 24
ADuM3440/ADuM3441/ADuM3442
Data Sheet
ABSOLUTE MAXIMUM RATINGS
Ambient temperature = 25°C, unless otherwise noted.
Table 9.
Parameter
Storage Temperature Range (TST)
Ambient Operating Temperature Range (TA)
Supply Voltages (VDD1, VDD2) 1
Input Voltage (VIA, VIB, VIC, VID, VE1, VE2)1, 2
Output Voltage (VOA, VOB, VOC, VOD)1, 2
Average Output Current per Pin 3
Side 1 (IO1)
Side 2 (IO2)
Common-Mode Transients (CMH, CML) 4
Rating
−65°C to +150°C
−40°C to +105°C
−0.5 V to +7.0 V
−0.5 V to VDD1 + 0.5 V
−0.5 V to VDDO + 0.5 V
−18 mA to +18 mA
−22 mA to +22 mA
−100 kV/µs to
+100 kV/µs
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
1
All voltages are relative to their respective ground.
VDDI and VDDO refer to the supply voltages on the input and output sides of a
given channel, respectively. See the PC Board Layout section.
3
See Figure 4 for maximum rated current values for various temperatures.
4
Refers to common-mode transients across the insulation barrier. Commonmode transients exceeding the Absolute Maximum Ratings can cause latchup or permanent damage.
2
Table 10. Maximum Continuous Working Voltage 1
Parameter
AC Voltage, Bipolar Waveform
AC Voltage, Unipolar Waveform
Basic Insulation
Reinforced Insulation
DC Voltage
Basic Insulation
Reinforced Insulation
1
Max
565
Unit
V peak
Constraint
50-year minimum lifetime
1131
560
V peak
V peak
Maximum approved working voltage per IEC 60950-1
Maximum approved working voltage per IEC 60950-1 and VDE V 0884-10
1131
560
V peak
V peak
Maximum approved working voltage per IEC 60950-1
Maximum approved working voltage per IEC 60950-1 and VDE V 0884-10
Refers to continuous voltage magnitude imposed across the isolation barrier. See the Insulation Lifetime section for more details.
Table 11. Truth Table (Positive Logic)
VIX Input 1
H
L
X
X
X
X
1
2
VEX Input 2
H or NC
H or NC
L
H or NC
L
X
VDDI State1
Powered
Powered
Powered
Unpowered
Unpowered
Powered
VDDO State1
Powered
Powered
Powered
Powered
Powered
Unpowered
VOX Output1 Notes
H
L
Z
H
Outputs return to the input state within 1 µs of VDDI power restoration.
Z
Indeterminate Outputs return to the input state within 1 µs of VDDO power
restoration if VEX state is H or NC. Outputs return to high impedance
state within 8 ns of VDDO power restoration if VEX state is L.
VIX and VOX refer to the input and output signals of a given channel (A, B, C, or D). VEX refers to the output enable signal on the same side as the VOX outputs. VDDI and
VDDO refer to the supply voltages on the input and output sides of the given channel, respectively.
In noisy environments, connecting VEX to an external logic high or low is recommended.
Rev. D | Page 12 of 24
Data Sheet
ADuM3440/ADuM3441/ADuM3442
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
VDD1 1
16
VDD2
GND1* 2
15
GND2*
VIA 3
ADuM3440
14
VOA
VIB 4
TOP VIEW
(Not to Scale)
13
VOB
VIC 5
12
VOC
VID 6
11
VOD
NC 7
10
VE2
GND1* 8
9
GND2*
06837-005
NC = NO CONNECT
*PIN 2 AND PIN 8 ARE INTERNALLY CONNECTED AND CONNECTING BOTH TO
GND1 IS RECOMMENDED. PIN 9 AND PIN 15 ARE INTERNALLY CONNECTED AND
CONNECTING BOTH TO GND2 IS RECOMMENDED.
Figure 5. ADuM3440 Pin Configuration
Table 12. ADuM3440 Pin Function Descriptions
Pin No.
1
2, 8
3
4
5
6
7
9, 15
10
Mnemonic
VDD1
GND1
VIA
VIB
VIC
VID
NC
GND2
VE2
11
12
13
14
16
VOD
VOC
VOB
VOA
VDD2
Description
Supply Voltage for Isolator Side 1, 3.0 V to 5.5 V.
Ground 1. Ground reference for Isolator Side 1.
Logic Input A.
Logic Input B.
Logic Input C.
Logic Input D.
No Connect.
Ground 2. Ground reference for Isolator Side 2.
Output Enable 2. Active high logic input. VOA, VOB, VOC, and VOD outputs are enabled when VE2 is high or disconnected.
VOA, VOB, VOC, and VOD outputs are disabled when VE2 is low. In noisy environments, connecting VE2 to an external
logic high or low is recommended.
Logic Output D.
Logic Output C.
Logic Output B.
Logic Output A.
Supply Voltage for Isolator Side 2, 3.0 V to 5.5 V.
Rev. D | Page 13 of 24
Data Sheet
VDD1 1
16
VDD2
GND1* 2
15
GND2*
VIA 3
ADuM3441
14
VOA
VIB 4
TOP VIEW
(Not to Scale)
13
VOB
12
VOC
VOD 6
11
VID
VE1 7
10
VE2
GND1* 8
9
GND2*
VIC 5
*PIN 2 AND PIN 8 ARE INTERNALLY CONNECTED AND CONNECTING BOTH TO
GND1 IS RECOMMENDED. PIN 9 AND PIN 15 ARE INTERNALLY CONNECTED AND
CONNECTING BOTH TO GND2 IS RECOMMENDED.
06837-006
ADuM3440/ADuM3441/ADuM3442
Figure 6. ADuM3441 Pin Configuration
Table 13. ADuM3441 Pin Function Descriptions
Pin No.
1
2, 8
3
4
5
6
7
Mnemonic
VDD1
GND1
VIA
VIB
VIC
VOD
VE1
9, 15
10
GND2
VE2
11
12
13
14
16
VID
VOC
VOB
VOA
VDD2
Description
Supply Voltage for Isolator Side 1, 3.0 V to 5.5 V.
Ground 1. Ground reference for Isolator Side 1.
Logic Input A.
Logic Input B.
Logic Input C.
Logic Output D.
Output Enable 1. Active high logic input. VOD output is enabled when VE1 is high or disconnected. VOD is disabled
when VE1 is low. In noisy environments, connecting VE1 to an external logic high or low is recommended.
Ground 2. Ground reference for Isolator Side 2.
Output Enable 2. Active high logic input. VOA, VOB, and VOC outputs are enabled when VE2 is high or disconnected. VOA,
VOB, and VOC outputs are disabled when VE2 is low. In noisy environments, connecting VE2 to an external logic high or
low is recommended.
Logic Input D.
Logic Output C.
Logic Output B.
Logic Output A.
Supply Voltage for Isolator Side 1, 3.0 V to 5.5 V.
Rev. D | Page 14 of 24
ADuM3440/ADuM3441/ADuM3442
VDD1 1
16
VDD2
GND1* 2
15
GND2*
VOA
VIA 3
ADuM3442
14
VIB 4
TOP VIEW
(Not to Scale)
13
VOB
12
VIC
VOC 5
VOD 6
11
VID
VE1 7
10
VE2
GND1* 8
9
GND2*
*PIN 2 AND PIN 8 ARE INTERNALLY CONNECTED AND CONNECTING BOTH TO
GND1 IS RECOMMENDED. PIN 9 AND PIN 15 ARE INTERNALLY CONNECTED AND
CONNECTING BOTH TO GND2 IS RECOMMENDED.
06837-007
Data Sheet
Figure 7. ADuM3442 Pin Configuration
Table 14. ADuM3442 Pin Function Descriptions
Pin No.
1
2, 8
3
4
5
6
7
Mnemonic
VDD1
GND1
VIA
VIB
VOC
VOD
VE1
9, 15
10
GND2
VE2
11
12
13
14
16
VID
VIC
VOB
VOA
VDD2
Function
Supply Voltage for Isolator Side 1, 3.0 V to 5.5 V.
Ground 1. Ground reference for Isolator Side 1.
Logic Input A.
Logic Input B.
Logic Output C.
Logic Output D.
Output Enable 1. Active high logic input. VOC and VOD outputs are enabled when VE1 is high or disconnected. VOC and
VOD outputs are disabled when VE1 is low. In noisy environments, connecting VE1 to an external logic high or low is
recommended.
Ground 2. Ground reference for Isolator Side 2.
Output Enable 2. Active high logic input. VOA and VOB outputs are enabled when VE2 is high or disconnected. VOA and
VOB outputs are disabled when VE2 is low. In noisy environments, connecting VE2 to an external logic high or low is
recommended.
Logic Input D.
Logic Input C.
Logic Output B.
Logic Output A.
Supply Voltage for Isolator Side 2, 3.0 V to 5.5 V.
Rev. D | Page 15 of 24
ADuM3440/ADuM3441/ADuM3442
Data Sheet
140
30
120
25
100
CURRENT (mA)
35
20
5V
15
10
80
5V
60
40
3.3V
3.3V
20
0
0
50
100
DATA RATE (Mbps)
150
0
0
Figure 8. Typical Input Supply Current per Channel vs. Data Rate
for 5 V and 3.3 V Operation
50
100
DATA RATE (Mbps)
150
06837-011
5
06837-008
CURRENT/CHANNE L (mA)
TYPICAL PERFORMANCE CHARACTERISTICS
Figure 11. Typical ADuM3440 VDD1 Supply Current vs. Data Rate
for 5 V and 3.3 V Operation
50
14
45
12
35
CURRENT (mA)
CURRENT/CHANNEL (mA)
40
10
8
5V
6
30
5V
25
20
15
4
3.3V
3.3V
10
2
0
50
100
DATA RATE (Mbps)
150
0
06837-009
0
0
Figure 9. Typical Output Supply Current per Channel vs. Data Rate
for 5 V and 3.3 V Operation (No Output Load)
50
100
DATA RATE (Mbps)
150
06837-012
5
Figure 12. Typical ADuM3440 VDD2 Supply Current vs. Data Rate
for 5 V and 3.3 V Operation
20
120
18
100
14
CURRENT (mA)
CURRENT/CHANNEL (mA)
16
12
5V
10
8
6
80
60
5V
40
3.3V
3.3V
4
20
0
50
100
DATA RATE (Mbps)
150
Figure 10. Typical Output Supply Current per Channel vs. Data Rate
for 5 V and 3.3 V Operation (15 pF Output Load)
0
0
50
100
DATA RATE (Mbps)
150
Figure 13. Typical ADuM3441 VDD1 Supply Current vs. Data Rate
for 5 V and 3.3 V Operation
Rev. D | Page 16 of 24
06837-013
0
06837-010
2
Data Sheet
ADuM3440/ADuM3441/ADuM3442
90
70
80
60
70
CURRENT (mA)
40
5V
30
60
50
5V
40
30
20
3.3V
3.3V
20
10
0
0
50
100
DATA RATE (Mbps)
150
Figure 14. Typical ADuM3441 VDD2 Supply Current vs. Data Rate
for 5 V and 3.3 V Operation
0
0
50
100
DATA RATE (Mbps)
150
06837-015
10
06837-014
CURRENT (mA)
50
Figure 15. Typical ADuM3442 VDD1 or VDD2 Supply Current vs.Data Rate
for 5 V and 3.3 V Operation
Rev. D | Page 17 of 24
ADuM3440/ADuM3441/ADuM3442
Data Sheet
APPLICATIONS INFORMATION
PC BOARD LAYOUT
VDD1
GND1
VIA
VIB
VIC/OC
VID/OD
VE1
GND1
VDD2
GND2
VOA
VOB
VOC/IC
VOD/ID
VE2
GND2
06837-017
The ADuM344x digital isolator requires no external interface
circuitry for the logic interfaces. Power supply bypassing is
strongly recommended at the input and output supply pins (see
Figure 16). Bypass capacitors are most conveniently connected
between Pin 1 and Pin 2 for VDD1 and between Pin 15 and Pin 16
for VDD2. The capacitor value should be between 0.01 μF and 0.1 μF.
The total lead length between both ends of the capacitor and
the input power supply pin should not exceed 20 mm. Bypassing
between Pin 1 and Pin 8 and between Pin 9 and Pin 16 should
be considered unless the ground pair on each package side is
connected close to the package.
SYSTEM-LEVEL ESD CONSIDERATIONS AND
ENHANCEMENTS
System-level ESD reliability (for example, per IEC 61000-4-x)
is highly dependent on system design, which varies widely by
application. The ADuM344x incorporate many enhancements
to make ESD reliability less dependent on system design. The
enhancements include the following:

ESD protection cells added to all input/output interfaces.

Key metal trace resistances reduced using wider geometry
and paralleling of lines with vias.

The SCR effect inherent in CMOS devices is minimized by
the use of guarding and isolation techniques between
PMOS and NMOS devices.

Areas of high electric field concentration eliminated using
45° corners on metal traces.

Supply pin overvoltage prevented with larger ESD clamps
between each supply pin and its respective ground.
Figure 16. Recommended Printed Circuit Board Layout
In applications involving high common-mode transients, care
should be taken to ensure that board coupling across the isolation
barrier is minimized. Furthermore, the board layout should be
designed such that any coupling that does occur equally affects
all pins on a given component side. Failure to ensure this could
cause voltage differentials between pins exceeding the device’s
absolute maximum ratings, thereby leading to latch-up or
permanent damage.
See the AN-1109 Application Note for board layout guidelines.
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the time it takes
a logic signal to propagate through a component. The propagation
delay to a logic low output may differ from the propagation
delay to a logic high.
INPUT (VIx)
50%
OUTPUT (VOx)
tPHL
06837-018
tPLH
50%
Figure 17. Propagation Delay Parameters
Pulse width distortion is the maximum difference between
these two propagation delay values and is an indication of how
accurately the input signal’s timing is preserved.
Channel-to-channel matching refers to the maximum amount
the propagation delay differs between channels within a single
ADuM344x component.
Propagation delay skew refers to the maximum amount the
propagation delay differs between multiple ADuM344x
components operating under the same conditions.
While the ADuM344x improve system-level ESD reliability,
they are no substitute for a robust system-level design. See the
AN-793 application note, ESD/Latch-Up Considerations with
iCoupler Isolation Products for detailed recommendations on
board layout and system-level design.
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
Positive and negative logic transitions at the isolator input cause
narrow (~1 ns) pulses to be sent to the decoder via the transformer.
The decoder is bistable and is, therefore, either set or reset by
the pulses, indicating input logic transitions. In the absence of
logic transitions at the input for more than ~1 μs, a periodic set
of refresh pulses indicative of the correct input state are sent to
ensure dc correctness at the output. If the decoder receives no
internal pulses of more than about 5 μs, the input side is assumed
unpowered or nonfunctional, in which case the isolator output
is forced to a default state (see the Absolute Maximum Ratings
section) by the watchdog timer circuit.
The limitation on the magnetic field immunity of the ADuM344x
is set by the condition in which induced voltage in the receiving
coil of the transformer is sufficiently large to either falsely set or
reset the decoder. The following analysis defines the conditions
under which this can occur. The 3 V operating condition of the
ADuM344x is examined because it represents the most susceptible
mode of operation.
The pulses at the transformer output have an amplitude greater
than 1.0 V. The decoder has a sensing threshold at about 0.5 V,
thus establishing a 0.5 V margin in which induced voltages can
be tolerated.
Rev. D | Page 18 of 24
Data Sheet
ADuM3440/ADuM3441/ADuM3442
The voltage induced across the receiving coil is given by
where:
β is magnetic flux density (gauss).
N is the number of turns in the receiving coil.
rn is the radius of the nth turn in the receiving coil (cm).
Given the geometry of the receiving coil in the ADuM344x and
an imposed requirement that the induced voltage be at most
50% of the 0.5 V margin at the decoder, a maximum allowable
magnetic field is calculated as shown in Figure 18.
MAXIMUM ALLOWABLE MAGNETIC FLUX
DENSITY (kgauss)
100
DISTANCE = 1m
100
10
DISTANCE = 100mm
1
DISTANCE = 5mm
0.1
0.01
1k
10k
100k
1M
10M
100M
MAGNETIC FIELD FREQUENCY (Hz)
10
06837-020
V = (−dβ/dt)∑ πr ; n = 1, 2, … , N
MAXIMUM ALLOWABLE CURRENT (kA)
1000
2
n
Figure 19. Maximum Allowable Current
for Various Current-to-ADuM344x Spacings
1
Note that at combinations of strong magnetic field and high
frequency, any loops formed by printed circuit board traces
could induce error voltages sufficiently large enough to trigger
the thresholds of succeeding circuitry. Care should be taken in
the layout of such traces to avoid this possibility.
0.1
0.01
0.001
1k
1M
10k
100k
10M
MAGNETIC FIELD FREQUENCY (Hz)
100M
06837-019
POWER CONSUMPTION
Figure 18. Maximum Allowable External Magnetic Flux Density
For example, at a magnetic field frequency of 1 MHz, the
maximum allowable magnetic field of 0.2 kgauss induces a
voltage of 0.25 V at the receiving coil. This is about 50% of the
sensing threshold and does not cause a faulty output transition.
Similarly, if such an event were to occur during a transmitted
pulse (and was of the worst-case polarity), it would reduce the
received pulse from >1.0 V to 0.75 V—still well above the 0.5 V
sensing threshold of the decoder.
The preceding magnetic flux density values correspond to
specific current magnitudes at given distances from the
ADuM344x transformers. Figure 19 expresses these allowable
current magnitudes as a function of frequency for selected
distances. As shown, the ADuM344x is extremely immune
and can be affected only by extremely large currents operated
at high frequency very close to the component. For the 1 MHz
example noted, one would have to place a 0.5 kA current 5 mm
away from the ADuM344x to affect the component’s operation.
The supply current at a given channel of the ADuM344x
isolator is a function of the supply voltage, the channel’s data
rate, and the channel’s output load.
For each input channel, the supply current is given by
IDDI = IDDI (Q)
f ≤ 0.5 fr
IDDI = IDDI (D) × (2f − fr) + IDDI (Q)
f > 0.5 fr
For each output channel, the supply current is given by
IDDO = IDDO (Q)
f ≤ 0.5 fr
−3
IDDO = (IDDO (D) + (0.5 × 10 ) × CL × VDDO) × (2f − fr) + IDDO (Q)
f > 0.5 fr
where:
IDDI (D), IDDO (D) are the input and output dynamic supply currents
per channel (mA/Mbps).
CL is the output load capacitance (pF).
VDDO is the output supply voltage (V).
f is the input logic signal frequency (MHz); it is half of the input
data rate expressed in units of Mbps.
fr is the input stage refresh rate (Mbps).
IDDI (Q), IDDO (Q) are the specified input and output quiescent
supply currents (mA).
To calculate the total VDD1 and VDD2 supply current, the supply
currents for each input and output channel corresponding to
VDD1 and VDD2 are calculated and totaled. Figure 8 and Figure 9
provide per-channel supply currents as a function of data rate
for an unloaded output condition. Figure 10 provides perchannel supply current as a function of data rate for a 15 pF
output condition. Figure 11 through Figure 15 provide total
VDD1 and VDD2 supply current as a function of data rate for
ADuM3440/ADuM3441/ADuM3442 channel configurations.
Rev. D | Page 19 of 24
ADuM3440/ADuM3441/ADuM3442
Data Sheet
Note that the voltage presented in Figure 21 is shown as sinusoidal
for illustration purposes only. It is meant to represent any voltage
waveform varying between 0 V and some limiting value. The
limiting value can be positive or negative, but the voltage cannot
cross 0 V.
The insulation lifetime of the ADuM344x depends on the
voltage waveform type imposed across the isolation barrier.
The iCoupler insulation structure degrades at different rates
depending on whether the waveform is bipolar ac, unipolar ac,
or dc. Figure 20, Figure 21, and Figure 22 illustrate these
different isolation voltage waveforms.
Bipolar ac voltage is the most stringent environment. The goal
of a 50-year operating lifetime under the ac bipolar condition
determines the maximum working voltage recommended by
Analog Devices.
RATED PEAK VOLTAGE
06837-021
Analog Devices performs accelerated life testing using voltage levels
higher than the rated continuous working voltage. Acceleration
factors for several operating conditions are determined. These
factors allow calculation of the time to failure at the actual working
voltage. The values shown in Figure 20 summarize the peak voltage
for 50 years of service life for a bipolar ac operating condition, and
the maximum CSA/VDE approved working voltages. In many
cases, the approved working voltage is higher than the 50-year
service life voltage. Operation at these high working voltages
can lead to shortened insulation life in some cases.
0V
Figure 20. Bipolar AC Waveform
RATED PEAK VOLTAGE
06837-022
All insulation structures eventually break down when subjected
to voltage stress over a sufficiently long period. The rate of
insulation degradation is dependent on the characteristics of
the voltage waveform applied across the insulation. In addition
to the testing performed by the regulatory agencies, Analog
Devices carries out an extensive set of evaluations to determine
the lifetime of the insulation structure within the ADuM344x.
In the case of unipolar ac or dc voltage, the stress on the insulation
is significantly lower, which allows operation at higher working
voltages while still achieving a 50-year service life. The working
voltages listed in Table 10 can be applied while maintaining the
50-year minimum lifetime provided the voltage conforms to
either the unipolar ac or dc voltage cases. Any cross insulation
voltage waveform that does not conform to Figure 21 or Figure 22
should be treated as a bipolar ac waveform and its peak voltage
should be limited to the 50-year lifetime voltage value listed in
Table 10.
0V
Figure 21. Unipolar AC Waveform
RATED PEAK VOLTAGE
06837-023
INSULATION LIFETIME
0V
Figure 22. DC Waveform
Rev. D | Page 20 of 24
Data Sheet
ADuM3440/ADuM3441/ADuM3442
OUTLINE DIMENSIONS
10.50 (0.4134)
10.10 (0.3976)
9
16
7.60 (0.2992)
7.40 (0.2913)
8
1.27 (0.0500)
BSC
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
10.65 (0.4193)
10.00 (0.3937)
0.75 (0.0295)
45°
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
SEATING
PLANE
8°
0°
1.27 (0.0500)
0.40 (0.0157)
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
03-27-2007-B
1
Figure 23. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body (RW-16)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model 1, 2
ADuM3440CRWZ
ADuM3441CRWZ
ADuM3442CRWZ
1
2
Number of
Inputs,
VDD1 Side
4
3
2
Number of
Inputs,
VDD2 Side
0
1
2
Maximum
Data Rate
(Mbps)
150
150
150
Maximum
Propagation
Delay, 5 V (ns)
32
32
32
Maximum
Pulse Width
Distortion (ns)
2
2
2
Z = RoHS Compliant Part.
Tape and reel are available. The addition of an -RL suffix designates a 13” (1,000 units) tape-and-reel option.
Rev. D | Page 21 of 24
Temperature
Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package
Description
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
Package
Option
RW-16
RW-16
RW-16
ADuM3440/ADuM3441/ADuM3442
Data Sheet
NOTES
Rev. D | Page 22 of 24
Data Sheet
ADuM3440/ADuM3441/ADuM3442
NOTES
Rev. D | Page 23 of 24
ADuM3440/ADuM3441/ADuM3442
Data Sheet
NOTES
©2007–2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06837-0-2/12(D)
Rev. D | Page 24 of 24