SMT Inductors, SIMID Series B82422H SIMID 1210−H Size 1210 (EIA) or 3225 (IEC) Rated inductance 1 to 680 H Rated current 61 to 1150 mA Construction Ferrite drum core Laser−welded winding Flame−retardant encapsulation Features Very high current handling capability Suitable for reflow soldering acc. JEDEC J−STD 020C lead−free, RoHS−compatible qualified acc. AEC−Q200 Applications Filtering of supply voltages, coupling, decoupling DC/DC converters / switch mode power supplies Automotive electronics Telecommunications Terminals Electro−plated Base material CuSn6 0,4m Cu; 1−2m Ag; 5−7m Sn (lead-free) Marking Marking on component: L value (in H) and tolerance of L value (coded) Date of manufacture (coded) Delivery mode 8mm blister tape, reel packing 180mm Ø reel (2000 pcs) or 330mm Ø reel (7500 pcs) Taping in accordance to IEC 60286−3. For details on taping and packing refer to data book “Chokes and Inductors” and to Epcos Homepage. Please read the important notes at the end of this document 1 B82422−H1*−3−7659 28.06.2006 SMT Inductors, SIMID Series B82422H SIMID 1210−H Dimensional drawing Layout recommendation Dimensions (mm) A B C D Reflow soldering 2,70 1,15 1,80 4,40 Marking 1) Soldering area, tinned Technical data and measuring conditions Electrical specifications at TA = 20°C Rated inductance LR Measured with impedance analyzer HP 4294A at frequency fL Q factor Qmin Measured with impedance analyzer HP 4294A at frequency fQ Rated current IR Maximum permissible DC with inductance decrease L/L0 10% and temperature increase of 45K at rated temperature of 105°C Self−resonance frequency fres,min Measured with network analyzer HP 8753 DC resistance Rmax measuring current < IR Climatic category 55/150/56 to IEC 60068−1 Solderability lead-free to IEC 60068−2−58 and Jedec J−STD 002B / JESD22−B102D Resistance to soldering heat to IEC 60068−2−20 and MIL−STD−202, method 210 Permissible PCB bending 2mm (100mm long standard PCB) Weight Approx. 50mg Please read the important notes at the end of this document 2 B82422−H1*−3−7659 28.06.2006 SMT Inductors, SIMID Series B82422H SIMID 1210−H Characteristics and ordering codes LR Toler− ance 1) Qmin H fL;fQ IR Rmax fres,min MHz mA Ω MHz Ordering code 2) ( 180−mm reel) Core material: ferrite 1,0 1,5 2,2 10% K 8 8 8 7,96 7,96 7,96 1150 900 800 0,10 0,14 0,16 150 110 90 B82422H1102K000 B82422H1152K000 B82422H1222K000 3,3 4,7 6,8 5% J 10% K 8 8 8 7,96 7,96 7,96 770 700 570 0,18 0,25 0,35 70 46 35 B82422H1332+000 B82422H1472+000 B82422H1682+000 10 15 22 12 12 12 2,52 2,52 2,52 500 390 330 0,46 0,72 1,00 30 26 21 B82422H1103+000 B82422H1153+000 B82422H1223+000 33 47 68 15 15 15 2,52 2,52 2,52 280 230 180 1,40 2,10 3,40 15 12 10 B82422H1333+000 B82422H1473+000 B82422H1683+000 100 150 220 20 20 20 0,796 0,796 0,796 150 120 100 4,80 7,50 10,90 8,0 6,0 5,5 B82422H1104+000 B82422H1154+000 B82422H1224+000 330 470 680 20 20 20 0,796 0,796 0,796 90 76 61 13,00 20,00 31,00 4,5 3,5 3,0 B82422H1334+000 B82422H1474+000 B82422H1684+000 1) Closer tolerances and special versions upon request. 2) Replace the + by the code letter for the required inductance tolerance. Please read the important notes at the end of this document 3 B82422−H1*−3−7659 28.06.2006 SMT Inductors, SIMID Series B82422H SIMID 1210−H Q factor versus frequency f measured with Agilent 4294A Current derating I op/I R versus ambient temperature TA 1,2 30 Iop I R Q 25 1 H H 20 0,8 H 0,6 15 H 10 0,4 5 0,2 0 0 0,1 1 10 MHz 0 20 40 60 80 100 °C 120 f 160 A Impedance |Z| versus frequency f measured with Agilent 4294A inductance L versus dc load current IDC measured with LCR meter Agilent 4284A 100000 1000 H 680H H H |Z| 10000 L Ω 100H 100 H H 1000 10 100 1 10 1 10H 1H 0,1 10 100 1000 MHz 0,01 Please read the important notes at the end of this document 0,01 0,1 1 10 A IDC f 4 B82422−H1*−3−7659 28.06.2006 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as “hazardous”). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, EPCOS-JONES, Baoke, CeraDiode, CSSP, MLSC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 5 of 5