Film Capacitors Metallized Polypropylene Film Capacitors (MKP) Series/Type: B32671P ... B32673P Date: April 2014 © EPCOS AG 2014. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Metallized polypropylene film capacitors (MKP) B32671P ... B32673P Power Factor Correction Typical applications PFC (Power Factor Correction) Dimensional drawing Climatic Max. operating temperature: 125 °C Climatic category (IEC 60068-1): 55/110/56 Construction Dielectric: polypropylene (PP) Wound capacitor technology Plastic case (UL 94 V-0) Epoxy resin sealing Dimensions in mm Features Very compact design Very small dimensions Very high ripple and peak current High frequency AC operation capability High voltage capability Excellent self-healing property RoHS-compatible Halogen-free capacitors available on request Lead spacing ±0.4 10 15 22.5 Terminals Parallel wire leads, lead free, tinned Special lead lengths available on request Marking Manufacturer's logo Lot number, series number Rated capacitance (coded) Capacitance tolerance (code letter) Rated DC voltage Date of manufacture (coded) Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For notes on taping, refer to chapter "Taping and packing“. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 18 Lead diameter d1 ±0.05 0.6 0.8 0.8 Type B32671P B32672P B32673P B32671P ... B32673P Power Factor Correction Overview of available types Lead spacing 10 mm 15 mm 22.5 mm Type B32671P B32672P B32673P Page 4 5 VRMS (V AC) 160 200 200 160 200 200 160 200 200 VR (V DC) 450 520 630 450 520 630 450 520 630 6 CR (µF) 0.068 0.082 0.10 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 1.0 1.5 2.0 2.2 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 18 B32671P Power Factor Correction Ordering codes and packing units (lead spacing 10 mm) VR V DC VRMS CR f ≤1 kHz V AC µF Ordering code (composition see below) Max. dimensions w×h×l mm 450 160 520 200 630 200 B32671P4104+*** B32671P4154+*** B32671P4184+*** B32671P4224+*** B32671P4274+*** B32671P4334+*** B32671P4394+*** B32671P4474+*** B32671P4684+*** B32671P4105+*** B32671P5823+*** B32671P5104+*** B32671P5154+*** B32671P5224+*** B32671P5334+*** B32671P5474+*** B32671P6683+*** B32671P6823+*** B32671P6104+*** B32671P6154+*** B32671P6184+*** B32671P6224+*** B32671P6334+*** B32671P6394+*** 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 14.0 × 13.0 7.0 × 16.0 × 13.0 8.0 × 17.5 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 7.0 × 16.0 × 13.0 8.0 × 17.5 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 14.0 × 13.0 8.0 × 17.5 × 13.0 8.0 × 17.5 × 13.0 0.10 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.68 1.0 0.082 0.10 0.15 0.22 0.33 0.47 0.068 0.082 0.10 0.15 0.18 0.22 0.33 0.39 Ammo pack pcs./MOQ 4000 4000 3320 3320 3320 2720 2720 2720 Reel Untaped pcs./MOQ 6800 6800 5200 5200 5200 4400 4400 4400 4000 3320 3320 2720 6800 5200 5200 4400 4000 3320 3320 2720 2720 2720 6800 5200 5200 4400 4400 4400 pcs./MOQ 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerance on request. Composition of ordering code + = Capacitance tolerance code: J = ±5% K = ±10% M = ±20% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 240 = Crimped down to lead spacing 7.5 mm, Ammo pack 140 = Crimped down to lead spacing 7.5 mm, Reel 003 = Straight terminals, untaped (lead length 3.2 ± 0.3 mm) 000 = Straight terminals, untaped (lead length 61 mm) Page 4 of 18 B32672P Power Factor Correction Ordering codes and packing units (lead spacing 15 mm) VR V DC VRMS CR f ≤1 kHz V AC µF Ordering code (composition see below) 450 160 520 200 630 200 B32672P4104+*** 5.0 × 10.5 × 18.0 B32672P4224+*** 5.0 × 10.5 × 18.0 B32672P4334+*** 5.0 × 10.5 × 18.0 B32672P4474+*** 5.0 × 10.5 × 18.0 B32672P4564+*** 6.0 × 11.0 × 18.0 B32672P4684+*** 6.0 × 12.0 × 18.0 B32672P4105+*** 7.0 × 12.5 × 18.0 B32672P4155+*** 9.0 × 17.5 × 18.0 B32672P4205+*** 9.0 × 17.5 × 18.0 B32672P4225+*** 11.0 × 18.5 × 18.0 B32672P5154+*** 5.0 × 10.5 × 18.0 4680 B32672P5224+*** 5.0 × 10.5 × 18.0 4680 B32672P5334+*** 6.0 × 11.0 × 18.0 3840 B32672P5474+*** 7.0 × 12.5 × 18.0 3320 B32672P5684+*** 8.5 × 14.5 × 18.0 2720 B32672P5105+*** 9.0 × 17.5 × 18.0 2560 B32672P5155+*** 11.0 × 18.5 × 18.0 B32672P6154+*** 5.0 × 10.5 × 18.0 4680 B32672P6224+*** 6.0 × 11.0 × 18.0 3840 B32672P6334+*** 7.0 × 12.5 × 18.0 3320 B32672P6474+*** 8.0 × 14.0 × 18.0 2920 B32672P6684+*** 9.0 × 17.5 × 18.0 2560 B32672P6105+*** 11.0 × 18.5 × 18.0 0.10 0.22 0.33 0.47 0.56 0.68 1.0 1.5 2.0 2.2 0.15 0.22 0.33 0.47 0.68 1.0 1.5 0.15 0.22 0.33 0.47 0.68 1.0 Max. dimensions w×h×l mm Ammo pack pcs./MOQ 4680 4680 4680 4680 3840 3840 3320 2560 2560 Reel Untaped pcs./MOQ 5200 5200 5200 5200 4400 4400 3600 2800 2800 2200 5200 5200 4400 3600 2800 2800 2200 5200 4400 3600 3000 2800 2200 pcs./MOQ 4000 4000 4000 4000 4000 4000 4000 2000 2000 1200 4000 4000 4000 4000 2000 2000 1000 4000 4000 4000 2000 2000 1000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerance on request. Composition of ordering code + = Capacitance tolerance code: J = ±5% K = ±10% M = ±20% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 255 = Crimped down to lead spacing 7.5 mm, Ammo pack 155 = Crimped down to lead spacing 7.5 mm, Reel 003 = Straight terminals, untaped (lead length 3.2 ± 0.3 mm) 000 = Straight terminals, untaped (lead length 61 mm) Page 5 of 18 B32673P Power Factor Correction Ordering codes and packing units (lead spacing 22.5 mm) VR V DC VRMS CR f ≤1 kHz V AC µF Ordering code (composition see below) Max. dimensions w×h×l mm 450 160 520 200 630 200 B32673P4105+*** B32673P4155+*** B32673P4225+*** B32673P5474+*** B32673P5564+*** B32673P5684+*** B32673P5105+*** B32673P5155+*** B32673P5225+*** B32673P6334+*** B32673P6474+*** B32673P6564+*** B32673P6684+*** B32673P6105+*** B32673P6155+*** B32673P6225+*** 6.0 × 15.0 × 26.5 7.0 × 16.0 × 26.5 8.5 × 16.5 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 7.0 × 16.0 × 26.5 10.5 × 16.5 × 26.5 10.5 × 20.5 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 6.0 × 15.0 × 26.5 7.0 × 16.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 18.5 × 26.5 12.0 × 22.0 × 26.5 1.0 1.5 2.2 0.47 0.56 0.68 1.0 1.5 2.2 0.33 0.47 0.56 0.68 1.0 1.5 2.2 Ammo pack pcs./MOQ 2720 2320 1920 2720 2720 2720 2320 1560 Reel Untaped pcs./MOQ 2800 2400 2000 2800 2800 2800 2400 1600 2720 2720 2720 2320 1920 1560 2800 2800 2800 2400 2000 1600 pcs./MOQ 2880 2520 2040 2880 2880 2880 2520 2160 2160 2880 2880 2880 2520 2040 2160 1800 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerance on request. Composition of ordering code + = Capacitance tolerance code: J = ±5% K = ±10% M = ±20% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 003 = Untaped (lead length 3.2 ± 0.3 mm) 000 = Untaped (lead length 61 mm) Page 6 of 18 B32671P ... B32673P Power Factor Correction Technical data Reference standard: IEC 60384-16. All data given at T = 20 °C, otherwise is specified. Operating temperature range Dissipation factor tan δ (in 10-3) at 20 °C (upper limit values) Insulation resistance Rins at 100 V or time constant τ = CR Rins at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) Max. operating temperature Top, max Upper category temperature Tmax Lower category temperature Tmin Rated temperature TR 1 kHz 1.0 10 kHz 2.5 100 kHz 25.0 +125 °C +110 °C 55 °C +85 °C 30 GΩ (CR ≤ 0.33 µF) 10000 s (CR > 0.33 µF) 1.4 VR, 2 s Category voltage VC TA (°C) DC voltage derating AC voltage derating (continuous operation with TA ≤85 VC = VR VC,RMS = VRMS VDC or VAC at f ≤ 1 kHz) 85 <TA ≤110 VC = VR (165 Top)/80 VC,RMS = VRMS (165 Top)/80 Operating voltage Vop for Top (°C) DC voltage (max. hours) AC voltage (max. hours) short operating periods Top ≤100 Vop = 1.1 VC (1000 h) Vop = 1.0 VC,RMS (1000 h) (VDC or VAC at f ≤ 1 kHz) 100 <Top ≤125 Vop = 1.0 VC (1000 h) Vop = 1.0 VC,RMS (1000 h) Reliability: Failure rate λ 24 fit (≤ 1 10-7/h) at 0.5 VR, 40 °C Service life tSL 200000 h at 0.5 VR, 85 °C For conversion to other operating conditions and temperatures, refer to chapter "Reliability", page . Failure criteria: Total failure Short circuit or open circuit Failure due to variation Capacitance change ∆C/C > 10% of parameters Dissipation factor tan δ > 4 × upper limit values Insulation resistance Rins < 150 MΩ (CR ≤ 0.33 µF) Or time constant τ < 50 s (CR ≥ 0.33 µF) DC test voltage Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 18 B32671P ... B32673P Power Factor Correction Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. These parameters are given for isolated pulses in such a way that the heat generated by one pulse will be completely dissipated before applying the next pulse. For a train of pulses, please refer to the curves of permissible AC voltage-current versus frequency. dV/dt values Lead spacing VR VRMS V DC V AC 450 160 520 200 630 200 10 mm 15 mm 22.5 mm dV/dt in V/µs 140 200 250 120 160 180 100 110 130 10 mm 15 mm 22.5 mm k0 in V2/µs 126000 208000 315000 108000 166000 226000 90000 114000 163000 k0 values Lead spacing VR VRMS V DC V AC 450 160 520 200 630 200 Impedance Z versus frequency f (typical values) Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 18 B32671P Power Factor Correction Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C) For TA > 100 °C, please use derating factor Ft. Lead spacing 10 mm 450 V DC/160 V AC 520 V DC/200 V AC 630 V DC/200 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 18 B32672P Power Factor Correction Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C) For TA > 100 °C, please use derating factor Ft. Lead spacing 15 mm 450 V DC/160 V AC 520 V DC/200 V AC 630 V DC/200 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 10 of 18 B32673P Power Factor Correction Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C) For TA > 100 °C, please use derating factor Ft. Lead spacing 22.5 mm 450 V DC/160 V AC 520 V DC/200 V AC 630 V DC/200 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 18 B32671P Power Factor Correction Permissible AC current IRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C) For TA > 100 °C, please use derating factor Ft. Lead spacing 10 mm 450 V DC/160 V AC 520 V DC/200 V AC 630 V DC/200 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 18 B32672P Power Factor Correction Permissible AC current IRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C) For TA > 100 °C, please use derating factor Ft. Lead spacing 15 mm 450 V DC/160 V AC 520 V DC/200 V AC 630 V DC/200 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 18 B32673P Power Factor Correction Permissible AC current IRMS versus frequency f (for sinusoidal waveforms TA ≤ 100 °C) For TA > 100 °C, please use derating factor Ft. Lead spacing 22.5 mm 450 V DC/160 V AC 520 V DC/200 V AC 630 V DC/200 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 14 of 18 B32671P ... B32673P Power Factor Correction Maximum AC voltage (VRMS), current (IRMS) vs. frequency and temperature for TA > 100 ºC The graphs described in the previous section for the permissible AC voltage (VRMS) or current (IRMS) vs. frequency are given for a maximum ambient temperature TA ≤100 ºC. In case of higher ambient temperatures (TA), the self-heating (∆T) of the component must be reduced to avoid that temperature of the component (Top= TA + ∆T) reaches values above maximum operating temperature.The factor FT shall be applied in the following way: And FT is given by the following curve: Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 18 B32671P ... B32673P Power Factor Correction Testing and Standards Test Reference Conditions of test Performance requirements Electrical Parameters IEC 60384-16 Within specified limits Robustness of terminations IEC 60068-2-21 Voltage proof, 1.4 VR, 1 minute Insulation resistance, RINS Capacitance, C Dissipation factor, tan δ Tensile strength (test Ua1) Wire diameter Tensile force 0.5 < d1 ≤ 0.8 mm 10 N Resistance to soldering heat IEC 60068-2-20, Solder bath temperature at test Tb, 260 ± 5 °C, immersion for method 1A 10 seconds Capacitance and tan δ within specified limits ∆C/C0 ≤ 2% I∆ tan δ l ≤ 0.001 I∆C/C0 I ≤ 2% I∆ tan δ I ≤ 0.002 RINS ≥ 50% of initial limit Rapid change of IEC 60384-16 temperature TA = lower category temperature TB = upper category temperature Five cycles, duration t = 30 min. Vibration IEC 60384-16 Bump IEC 60384-16 Climatic sequence IEC 60384-16 Damp Heat Steady State IEC 60384-16 Test FC: vibration sinusoidal No visible damage Displacement: 0.75 mm Accleration: 98 m/s2 Frequency: 10 Hz ... 500 Hz Test duration: 3 orthogonal axes, 2 hours each axe Test Eb: Total 4000 bumps with No visible damage I∆C/C0 I ≤ 2% 390 m/s2 mounted on PCB I∆ tan δ I ≤ 0.001 6 ms duration RINS ≥ 50% of initial limit Dry heat Tb / 16 h. No visible damage Damp heat cyclic, 1st cycle I∆C/C0 I ≤ 2% + 55 °C / 24h / 95% ... 100% RH I∆ tan δ I ≤ 0.001 Cold Ta / 2h RINS ≥ 50% of initial limit Damp heat cyclic, 5 cycles + 55 °C / 24h / 95% ... 100% rh Test Ca No visible damage 40 °C / 93% RH / 56 days I∆C/C0 I ≤ 3% I∆ tan δ I ≤ 0.003 RINS ≥ 50% of initial limit 60 °C / 95% RH / 1000 hours with No visible damage I∆C/C0 I ≤ 10% VR, DC I∆ tan δ I ≤ 0.004 RINS ≥ 50% of initial limit High temperature high humidity with load Please read Cautions and warnings and Important notes at the end of this document. Page 16 of 18 B32671P ... B32673P Power Factor Correction Endurance A 85 °C/ 1.1 VR / 1000 hours Endurance B 110 °C/ 1.1 VC / 1000 hours Endurance C 125 °C/ 1.1 VC / 1000 hours Endurance D 85 °C/ VR + 4 ARMS,1000 KHz/ 1000 hours Please read Cautions and warnings and Important notes at the end of this document. Page 17 of 18 No visible damage I∆C/C0 I ≤ 5% I∆ tan δ I ≤ 0.004 RINS ≥ 50% of initial limit No visible damage I∆C/C0 I ≤ 10% I∆ tan δ I ≤ 0.004 RINS ≥ 50% of initial limit No visible damage I∆C/C0 I ≤ 10% I∆ tan δ I ≤ 0.004 RINS ≥ 50% of initial limit No visible damage I∆C/C0 I ≤ 10% I∆ tan δ I ≤ 0.004 RINS ≥ 50% of initial limit Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CeraPlas, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, TFAP, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 18 of 18